Search Documents

By E. J. Gleim

In April 1932, the Bureau of Mines published Information Circular 6595, entitled "Data in Reference to Installation of Cables in Shafts and Boreholes", in which were described methods followed in various sections of the United States when electrical circuits are taken into mines by means of cables suspended in shafts and boreholes. In view of the present tendency to extend high-tension cables along entries and passageways from the bottom of the shaft, borehole, or other point of entrance to coal mines rather than over the surface, it is deemed that the various methods of installing such cables deserve careful consideration, particularly in mines in which gas and coal dust contribute to explosion hazards. This is especially true of localities where there is an inclination to restrict the extension of 2,300- and 4,000-volt circuits into the mines. Probably it is feared that accidental contact with the cables of such circuits may result in more serious shock than with lower voltages; also, it is possible that new circuits are regarded merely as explosion hazards additional to those already existing, regardless of the manner in which the new circuits may be installed. It is the firm belief of some engineers that the circuits can be installed so that they will not be damaged by wrecks or roof falls, thereby eliminating the hazard of explosion from this source while at the same time making the chance of accidental contact remote if not impossible. Moreover, some believe that fire hazards from direct-current systems can be reduced by keeping motor-generator sets close to load centers. Thus, although the alternating-current circuits would be lengthened, the size and extent of direct-current circuits would be kept to a minimum.

Jan 1, 1939

By P. C. Good

High-purity chromium was prepared in massive form by the electrolysis of chromium trioxide solution at high temperatures. The metal thus obtained, containing 50 to 150 p.p.m. of oxygen, 20 p.p.m. of nitrogen, and traces of metallic impurities, could be hot-worked to rod and sheet and drawn to wire ductile at room temperatures. Optimum concentrations and operating conditions were established for the deposition of chromium from chromic acid baths containing sulfate, fluoride, and silicofluoride ions. Current efficiencies of 13 percent were attained with baths containing sulfate ion, and efficiencies of 40 to 44 percent with baths containing fluoride and silicofluoride ions. Cation exchange resins were used for removing metallic impurities from chromic acid solutions containing sulfate ion; solutions containing fluoride and silicofluoride ions were purified by recrystallization.

Jan 1, 1960

By Raymond B. Lucas

"Distinction between Tripoli and Diatomaceous EarthMuch confusion exists both in the literature and in the trade as to the proper use of the terms tripoli, tripolite diatomeceons or infusoriai earth, and kieseigunr. All of these terms are often used synonymously by the trade and even in mineralogists and other reference books. Actually, tripoli is a ma- is a material of definite and distinct physical and chemical properties and all of the other terms belong to a different material with just as definite and distinct properties.Originally the term tripolite (loosely called tripole) was given to a diatomaceous cart from Tripoli in Northern Africa. Dena (J.D. Dana, A System of Mineralogy 6th Ed.) calls this material tripolite and gives no authority for the use of the terms tripoli. Between 1880 and 1890 the deposits near Missouri, were opened and the material placed on the market as ""Tripoli"" no doubt due to its resemblance in some respect to the original tripolite or diatomaceous worth from Tripoli. Since that time the term tripoli has with increasing definitenesss been reserved for the Seneca material and other siliceous of similar origin and physical properties, while all siliceous material of organic origin, containing dilators, has been called diatomaceous earth (or its synonyms infusorial earth, kiselguhr, etc.). Rottenstone is sometimes classed with tripoli."

Nov 1, 1920

By C. B. Manula

In this report, the application of the Open Pit Materials Handling Simulator (OPMHS) to a Southwestern surface mine using draglines and front-end loaders is described. The specific objective of the study is to demonstrate the application of the simulator to analyze mine planning and to analyze alternatives for increased production. The simulator was verified by comparing long term production figures to the simulated results from data collected on a mine visit. A short term and a long term alternative are studied with projected productivities and scheduling. No economic analysis of these proposals were performed.

Jan 1, 1977

By R. R. Allen

Gieseler plastometer tests were performed on eight western coking coals at retort - immersion depths ranging from 2 to 3-3 /4 inches (measured to the center of the coal charge ) . Increased maximum fluidities were associated with greater retort - immersion depths , the most pronounced increases being observed on highly swelling coals when tested at 3-3 /4 inches . The maximum fluidity of one of these coals when tested at 3-3 /4 inches was 146 percent greater than that observed at 24 inches . Retort - immersion depth had no significant effect on the temperatures of initial softening , fusion , maximum fluidity , end of fusion , and solidification .

Jan 1, 1964

By O. C. Blade

This report on the properties of motor fuels sold through service stations in the United States was made in accordance with a cooperative agreement between the American Petroleum Institute and the Bureau of Mines of the United States Department of the Interior. By agreement with the American Petroleum Institute, identification of the items is confidential. It presents analytical data for 3,924 samples, representing the products of 116 companies. The samples were collected during June, July, and August, 1954. As in previous surveys, the gasolines covered by this survey include those from both large and small suppliers, The data were obtain& by laboratories of various refiners, motor manufacturers, and chemical companies and submitted to the Bureau of Mines for compilation, A list of the National Motor-Gasoline Survey reports published during the past 10 years is given on page 5.

Jan 1, 1955

By T. E. Green, E. F. Spano, W. J. Campbell

A combined ion exchange X- ray spectrographic method was evaluated for the determination of 11 metallic elements in high - purity tungsten : Aluminum , calcium , chromium , cobalt , copper , iron , magnesium , manganese , nickel , titanium , and zinc . Copper , nickel , and manganese in the 5- to 100 - microgram range ( 1 to 20 parts per million based on 5 - gram samples of tungsten ) , calcium in the 10- to 100 - microgram range , and cobalt in the 5- to 20 - microgram range can be determined within an accuracy of ± 10 percent of the amount present . Limits of detection of these elements are 0.05 to 0.14 microgram . The overall method was unsatisfactory for the determination of aluminum , chromium , iron , magnesium , titanium and zinc in tungsten .

Jan 1, 1964

By C. E. Henning

The total number of petroleum refineries in the United States on January 1, 1958, was 318 and their total crude-oil throughput capacity was 9,407,707 barrels per day, according to the Bureau of Mines annual survey. During 1957, 3 new refineries began operating while 4 refineries were retired. Although there was 1 less refinery, the total crude-oil throughput capacity at the beginning of 1958 was 284,033 barrels per day, or 3 percent, more than the January 1, 1957, level. During 1957 all refinery districts showed increases in capacity. The largest increase, 27 percent, occurred in the West Coast district followed by the Indiana-Illinois-Kentucky district with 14-percent increase and the Texas Gulf Coast district with 13-percent increase. The national increase in capacity had the effect of raising the capacity of the average refinery from 28,601 to 29,584 barrels per day. New crude-oil capacity under construction on January 1, 1958, totaled 185,265 barrels, and an additional 297,885 barrels capacity was reported building as replacement for existing facilities. Included in total new construction were 2 new refineries, 1 in Washington and another in Texas, with planned processing capacities of 45,000 barrels and 8,550 barrels per day, respectively.

Jan 1, 1958

By Joseph A. Conway

This paper is one of a series dealing with the mining and crushing methods and costs of the nonmetallic industries, prepared under the sponsorship of and in cooperation with the U. S. Bureau of Mines,. The quarrying methods described in this paper are those used at the Monocacy trap rock quarry which annually produces from 450,000 to 500,000 tons of crushed stone. This property is located 3 miles east of Birdsboro at Monacacy, Pa., and is one of the three quarries operated by the John T. Dyer Quarry Co. Throughout the paper an effort is made to explain the various methods used and the cost of operation.

Jan 1, 1931

By N. A. Gokcen

In this Bureau of Mines report, appropriate equations correlating the activity of water with the activities of electrolytes in binary and multicomponent solutions have been derived for computer calculation. It was found that the half-integer power series are far superior to the integer power series, for both types of series having the same number of terms. The pro-posed method of calculation is capable of accurately yielding the activities of all components from the measurements of the activity of a single component at various concentrations. This method replaces the cumbersome and objection-able method of graphical integration of the Gibbs-Duhem equation. Two novel methods are proposed for determination of activities of electrolyte solutions important in hydrometallurgy; (1) Water vapor pressure measurement by differential pressure transducers having an accuracy of 0.001 pet, and (2) transpiration method with an inert gas bubbled through concentrated solutions followed by the analysis of the evaporated and redissolved electrolytes with specific ion electrodes having a sensitivity of ±10-10 molal. The first method is suitable for nonvolatile electrolytes, and the second, for volatile electrolytes such as hydrogen halides, HN03, H2S03, etc. The existing methods of estimation of ionic activities have been surveyed, and the best method has been selected, discussed, and summarized.

Jan 1, 1979

By Ronald S. Conti

This U.S. Bureau of Mines report discusses the results of research conducted in the Bureau's experimental mine at Lake Lynn Laboratory on the response of fire sensors to simulated mine fires, which included (1) a slowly developing coal-conveyor belt fire, (2) a rapidly burning liquid fuel-belt fire, and (3) a liquid fuel-belt fire in the presence of diesel exhaust. During these tests, several mine fire sensors were evaluated with respect to sensor placement, spacing, and type. The data indicate that smoke sensors alarm several minutes before CO sensors do; and that, in the presence of diesel exhaust, a prototype diesel-discriminating smoke sensor can successfully function without being sensitive to the diesel contaminants. The vertical placement of sensors in the entry near the fire was also shown to be critical in terms of alarm times. Additional data showed that variations exist in response time and level of response for two brands of electrochemical CO sensor. Results also indicate that early detection of fires will improve the probability of miners' escape, because of reduced smoke concentrations during the incipient stages of the fire.

Jan 1, 2010

This report describes a U.S. Bureau of Mines investigation into the removal of gate road chain pillars in conjunction with longwall retreat mining. The research objective was to determine, through evaluations of the loads imposed on the gate road pillars and supplemental support elements in the entries, how the pillars, supplemental support, and entries were affected by the longwall abutment pressure. To achieve this goal, vibrating wire stressmeters and hydraulic flat jack pressure cells were installed in the support elements to monitor stress change caused by abutment pressure as a function of longwall face advance. The findings documented in this report are the result of information collected from instrumentation and observation at the mine. Pillar and support loading measurements and stability observations revealed that the roof and the support elements remained stable during panel retreat, while the face progressed at a normal rate of advance. The ability to safely and efficiently mine chain pillars during panel retreat increases resource recovery and can provide several other benefits described in this report.

Jan 1, 2010

By J. Burlin Johnson

This report describes an investigation of the relationship between crater dimensions formed in laboratory blasting experiments and the mechanical properties of the material cratered. Scaled field data have been included when available. The results show that tensile strength and possibly other mechanical properties may be useful in predicting maximum crater dimensions.

Jan 1, 1963

By J. C. Johnson

In situ stresses are important input data for the design of safe, stable stope layouts and extraction sequences. However, it is commonly assumed that normal and shear stress gradients in a stress field are negligible and, consequently, that stresses are uniform throughout the region of analysis. To evaluate these assumptions and to provide input data for an analysis of a shaft pillar mining plan, in situ stresses were measured at the Homestake Mine, Lead, SD, using overcoring on hollow inclusion cells and borehole deformation gauges. These measurements were used with conventional least squares, best fit data reduction schemes. The results showed that normal stresses within the shaft pillar were less than, but comparable to, those estimated from finite-element modeling. Shear stresses were an order of magnitude less than normal stresses and varied considerably from site to site. Possible causes of this variability include effects of scale, elastic moduli, anisotropy, and axial strain. Because of the variability, it is not possible to determine the magnitude of horizontal stress gradients.

Jan 1, 2010

By B. M. Bird

For several years the U.S. Bureau of Mines and the University of Washington have been cooperating, in a study of coal tabling. The first pert of the work consisted of experiments using, one of the commercial-sized coal washing tables in the laboratories of the College of Mine. As an outgrowth of this work, hindered-settling classification has been successfully applied in the tabling of coal4, and several important improvements, mainly in the riffling, have been made in the table itself. Both of these developments have resulted in increasing the rapacity and efficiency of the coal-washing table. In order to facilitate further progress in this work an investigation has been undertaken to throw more light on the mechanism of table separation. The final separation of a table is obviously the resultant of several operations; namely, stratification, removal of the top strata or parts of them as washed coal by the cross-flowing water, and removal of the bottom strata or parts of

Jan 1, 1929

By W. M. Traver, A. M. Evans

"INTRODUCTION The Bureau of Mines undertook exploration in the Torlingua district, Texas, during June 1943, at a time when the demand for mercury for war industries was considerably more than the anticipated domestic production. In view of the impressive past production of the mines and the favorable geologic conditions in several underdeveloped areas in the district, the investigation was considered of immediate importance.Prior to initiation of the exploratory program, a preliminary examination of the district was made in August 1942 by A. B. Needham, an engineer of the Bureau of Mines. This examination was followed by a comprehensive geological study by the Federal Geological Survey 3/ and further investigation the Bureau of Mines."

Jan 1, 1947

By D. H. Desy

The Bureau of Mines studied the properties of copper that had been oxide dispersion-strengthened with 2 vol pct of either yttria or alumina. Compounds of copper and aluminum or yttrium, coprecipitated from aqueous solution, were converted to oxides; the copper was reduced, compacted, sintered, and extruded. For the resulting copper-dispersoid composites, room temperature tensile properties after annealing in hydrogen, elevated temperature tensile and stress-rupture properties, and electrical conductivity were determined. Compared with oxygen-free copper, copper-2 vol pct alumina or yttria had improved strength after annealing between 400° and 1,000° C, and improved elevated temperature strength, with little loss in electrical conductivity.

Jan 1, 1969

By M. W. Von Bernewitz

Corduroy is used for saving gold in small Land large milling plants throughout the world. Investigations by the Metallurgical Division of the Bureau of Mine indicate that corduroy blankets, used with or without a trap or jig in the mill classifier circuit, often are effective in concentrating gold and sulfides, especially if the gold does not amalgamate readily and if not enough sulfides are present to warrant the use of a shaking table, flotation cells, or cyanide plant. Most cold-mining countries include several or many small miner, that produce siliceous ores low in sulfides and gold, which can easily be amalgamated or caught in traps or jigs or on corduroy and shaking tables. At these mines the ore is crushed by stamps or bill mills, and the flow sheets include plates, flotation cells, and cyanide treatment, yet probably nearly as much of the pair minerals may be recovered by the less expensive plant. A well-known western maker of mine and mill equipment asserts, as the result of considerable observation of installed plants, that old and other valuable minerals should be caught as soon as they have been released by a mill, end recommends jigs to do this. A supplier of corduroy has informed us that at some mines this material is being replaced by jigs that catch gold as fine as 400-mesh. But for the small operator, inexpensive equipment such as a corduroy table may be better adapted and give a good recovery of gold and associated minerals.

Jan 1, 1939

By John Campbell, E. S. Baker, G. W. Jones

"INTRODUCTION In previous reports 5,6./ results were given showing the amount of natural ventilation that takes place in manholes (capacities, 74.1 to 308 cubic feet) when the number of ventilation openings in the manhole cover ranged from no openings to a maximum of 4g.The tests warranted the general conclusion that the ventilation or air changes taking place in, a manhole increase as the area of openings in the cover of the manhole is increased, and are proportional (with the exception of a few erratic tests) to the area of the openings in the cover. The area of the openings was the chief factor that affected ventilation.The results did not show any marked change in rate of ventilation due to increased capacity or shape of manhole, when the results were expressed in terms of air changes per day versus area of ventilation openings in square inches per 100 cubic feet of manhole space.It was observed during these investigations that in certain tests that showed erratic results (that is, did not agree with the general average for a given set of test conditions) the wind velocity during the test period was also abnormal. In view of these findings it was decided to conduct a series of tests in which the wind velocity across the openings in the manhole cover could be controlled accurately to determine the effect of wind velocity on ventilation rate."

Aug 1, 1938

By John Paul Gries

During World War II, when the curtailment of imports led to an unprecedented demand for domestically produced mica, beryl, and other pegmatitic minerals, the Bureau of Mines and the Geological Survey entered upon a program designed to expedite the production of these minerals from the Black Hills area of South Dakota. The program involved mapping, sampling and drilling many pegmatite dikes found in the southern portion of the area and beneficiation tests in the field and in the Bureau of Mines laboratories at Rapid. City, S. Dak., Rolla, Mo., Salt Lake City, Utah, and College Park, Md. This paper describes the mode of occurrence and the sampling and beneficiation tests on one dike, the Helen Beryl pegmatite, which was investigated as part of the general pegmatite study in South Dakota. Investigation of the Helen Beryl Pegmatite by the Bureau began in August 1943 and was terminated in April 1944. During this period the Bureau took a series of bulk samples from pits for beneficiation tests, drove an adit through the center of the dike to obtain feed for a bulk-sampling plant operation, and finally drilled a series of long holes to sample the deposit further. Geologists of the Federal Geological Survey mapped the deposit and the faces of all excavations and logged drill holes from sludge samples recovered from long-hole drilling.

Jan 1, 1949