Search Documents

By G. L. Gates

Five possible sources of water for waterflooding of petroleum reservoirs in the arid San Joaquin Valley of California were considered. Three of them (water produced with petroleum, water from a shallow saline aquifer, and waste irrigation water) were analyzed chemically; laboratory information for one (sea water) had been developed during a previous study. A series of laboratory tests made on the fifth source (fresh water) determined the solubility of calcium sulfate dihydrate in water. Laboratory analyses included the following: Chemical analyses of water produced with petroleum and waste irrigation water; solubility of calcium sulfate dihydrate in water and brines; the effect of excess sulfate on the solubility of calcium sulfate in brines; the presence of sulfate-reducing bacteria; and the permeability of cores from a petroleum reservoir to air, to water from other petroleum reservoirs, and to waste irrigation water. The results showed that most of the waters and mixtures of waters are compatible with petroleum reservoir waters and are generally suitable for injection. The calcium content of some of the formation waters is quite high, and care must be taken to prevent precipitation of calcium sulfate dihydrate. The permeability of the few cores tested was about the same to water and brines as to air, indicating that formation damage due to clay swelling will not be serious. The waters most likely to be available for injection are water produced with petroleum, water from shallow saline aquifers, and waste irrigation water.

Jan 1, 1970

By A. A. Cochran

The objective of the research was to determine the final distribution of cerium additions to steel, their effect on sulfide inclusions, and the usefulness of radiotracer methods in investigating steel problems. Fifty-gram heats of steel were prepared that contained either cerium 141 and nonradioactive sulfur, or sulfur 35 and nonradioactive cerium. These steels were studied by autoradiography, measurements of their surface radioactivities, optical microscopy, and chemical analysis. Samples of the crucibles were analyzed quantitatively for cerium or sulfur by radioactivity counting methods. The addition of cerium to steel melts reduced the size and number of iron sulfide inclusions in the resulting steel. A significant fraction of the sulfur and most of the cerium penetrated into the MgO crucible during the melting operation, The cerium inclusions in steel were identified as cerium sulfide. Radiotracer methods were found to be versatile and highly sensitive.

Jan 1, 1963

By David Schlain

The galvanic corrosion properties of titanium and zirconium were investigated by the Bureau of Mines. The dissimilar metals involved in these experiments included magnesium, magnesium alloy FS1, aluminum alloys, zinc, steel, tin, lead, copper, Monel, nickel, and several stainless steels. Couples were immersed in synthetic ocean water, tap water, 5-percent ammonium sulfate solution, 5-1/2-percent sodium chloride solution, sodium hydroxide solution, 0.1 N hydrochloric acid, and various concentrations of sulfuric acid.

Jan 1, 1956

By T. J. Williams

Researchers at the U.S. Bureau of Mines monitored rock mass response to mining of an experimental underhand longwall stope in Hecla Mining Co.'s LUCKY Friday Mine, Mullan, ID. This stope design, the Lucky Friday underhand longwall (LFUL), was proposed as a means of controlling rock bursting while also allowing increased mechanization of mining operations. Instruments were specifically manufactured to monitor three geomechanical factors (backfill performance, ramp stability, and rock mass response) that directly affect the success of stope design. Despite considerable difficulties with instrument installation and survival in the harsh mine environment, especially within the stope fill, sufficient information was collected to suggest that the LFUL method was successful in achieving project goals. This conclusion, in addition to favorable economic and operational evidence, led the mine to adopt the method throughout the mine. Indeed, this study and mining experience suggest that underhand longwall mining could be considered a feasible mining method for rock-burst-prone ground throughout the Coeur d'Alene District. Further Reports of Investigations (RI) in this series present in-depth analyses of the effects of backfill on rock bursting and calibration of a stope numerical model.

Jan 1, 2010

By Robert H. Bedford

As a result of the Bureau's general survey of quicksilver deposits in California, the Guadalupe mine area was among those chosen for exploration. Exploration, such as that at the Guadalupe, was aimed primarily at maintaining or increasing production of quicksilver during the critical wartime period. The project as originally planned contemplated sampling the dumps and prospecting some promising surface exposures by bulldozer trenches. Salvage was the objective in the first case and new ore in the second. Later, a program. of diamond drilling was added, designed to add both to ore reserves and to geological information. This report summarizes the history, notes the location and physical features, mentions property and ownership, and presents a brief description of the mine. The geology is outlined, and the work done by the Bureau of Mines is explained and supplemented with accompanying maps. The work involved repairing 1-1/4 miles of roads; bulldozing 13 trenches by removing 2,345 cubic yards of dumps to provide for sampling; digging and sampling 9,284 linear feet of hand trenches, digging and sampling numerous test pits; and drilling 7 diamond-drill holes, totaling 1,000 feet. A total of 419 samples, including 10 percent check samples, were taken. Exploration work in California at the time of this project was under the direction of Spangler Ricker, supervising engineer of the California field office, the late Robert Bedford was in charge of the fieldwork on this project.

Jan 1, 1950

By John D. Sullivan

In leaching copper ores knowledge of the rate of dissolution of the copper minerals and of the impurities is desirable. With knowledge of these two factors and data as to what minerals are present in the ore the metallurgist has an excellent start on planning a leaching cycle to fit that ore. The rate of dissolution is rather difficult to predict, and the time required to leach a given ore may differ markedly from that required by another ore. The whole study as related to mixed oxidized and sulphide ores is one of relative rates of dissolution of the different copper minerals and the impurities in sulphuric aoid and in ferric sulphate. The aim of leaching is to choose a cycle and strength of solvents to extract a maximum amount of copper and a minimum of impurities. The consumption of reagents per unit of copper dissolved is a function of the strength of the reagents used and the relative rates of attack on copper minerals and impurities. An opportunity may exist of obtaining the kind of electrolyte wanted for electrolytic precipitation and yet of saving on the consumption of reagents by modifying the strength of ferric sulphate and of sulphuric acid during the cycle to fit the time needed for dissolving the sulphide and oxidized minerals present.

Jan 1, 1931

By William H. Pomroy

Spontaneous combustion fires involving high-sulfide-content ores are a relatively infrequent yet serious safety hazard in mining. They are also the cause of lengthy mine shutdowns because they typically occur in areas of a mine where abundant fuel material is present but which are inaccessible for fire fighting. This Bureau of Mines report describes research to design, fabricate, and test in the laboratory and field a system that warns of spontaneous combustion fires in metal mines. Overall performance of the detection system was found to be satisfactory, in that the system was capable of reliably detecting low levels of combustion products believed to indicate the preflaming stage of spontaneous combustion in metal mines. Installation of similar systems in mines with a high risk of spontaneous combustion is recommended. Principal operating problems and recommended corrective actions are also discussed.

Jan 1, 1987

By John D. Sullivan

In leaching copper ores knowledge of the rate of dissolution of the copper minerals and of the impurities is desirable. With knowledge of these two factors and data as to what minerals are present in the ore the metallurgist has an excellent start on planning a leach¬ing cycle to fit that ore. The rate of dissolution is rather difficult to predict, and the time required to leach a given ore may differ markedly from that required by another ore. The whole study as related to mixed oxidized and sulphide ores is one of relative rates of dissolution of the different copper minerals and the impurities in sulphuric acid and in ferric sulphate. The aim of leaching is to choose a cycle and strength of solvents to ex¬tract a maximum amount of copper and a minimum of impurities. The consumption of reagents per unit of copper dissolved is a function of the strength of the reagents used and the relative rates of attack on copper minerals and impurities. An opportunity may exist of ob¬taining the kind of electrolyte wanted for electrolytic precipitation and yet of saving on the consumption of reagents by modifying the strength of ferric sulphate and of sulphuric acid during the cycle to fit the time needed for dissolving the sulphide and oxidized minerals present. Former papers have considered the rate of dissolution of azurite, malachite, tenorite, chrysocolla, cuprite, chalcocite, boruite, and covellite in common leaching solvents. A paper soon to be written will consider some of the less important copper minerals. The present paper considers the rate of dissolution of copper from ores of the Southwest in sulphuric acid of varying strength and the ratio of sulphuric acid consumed to copper dis¬solved. In this study two ores containing the copper principally in an oxidized condition were used. A study of other ores, especially those containing high percentages of sulphide copper minerals, would be desirable, but since consumption of acid has paramount interest,

Jan 1, 1931

The National Personal Protective Technology Laboratory (NPPTL) of the National Institute for Occupational Safety and Health (NIOSH) has undertaken a collaborative study with the Mine Safety and Health Administration (MSHA) to determine how well self-contained self-rescuers (SCSRs), deployed in accordance with Federal regulations (30 CFR 75.1714), withstand the underground coal mining environment with regard to both physical damage and aging. Apparatus tested included the CSE SR-100, the Draeger OXY-K Plus, the MSA Life-Saver 60, and the Ocenco EBA 6.5 and M-20. This report presents findings regarding laboratory-tested SCSRs in the tenth phase of testing, from July 2004 to March 2006. The SCSRs were tested on a breathing and metabolic simulator and on a human subject walking on a treadmill. The tests performed in this study are not the tests used for certification (Title 42 of the Code of Federal Regulations, Part 84). The tests performed in this study continue until the apparatus are empty to enable comparison of new versus deployed apparatus. The method for obtaining deployed SCSRs for this evaluation was not a random selection from the deployed population of SCSRs. We sought older apparatus with visible environmental impact rather than newer apparatus, and we attempted to sample a wide range of deployment modes. Although the results of these tests are useful for observing performance of the tested SCSRs, they are not representative of all deployed SCSRs. This report is the last of 10 report phases begun in 1982. Previous reports describe phases 1 through 9 [Kyriazi et al. 1986; Kyriazi and Shubilla 1992, 1994, 1996, 2000, 2002, 2004, 2006] A new evaluation protocol, with revised sampling strategies, test methods, and reporting procedures, is currently being designed to enhance the applicability of the results. The results of these studies suggest that the large majority of SCSRs that pass their inspection criteria can be relied upon to provide a safe level of life support for mine escape purposes. However, the storage and handling in the mining environment seems to have caused performance degradation in some of the apparatus. In this phase, phase 10, we found some CSE SR-100s (93 tested) that exhibited high CO2 levels, stuck-together breathing hoses, starter-O2 failure, breathing hose punctures and tears, high breathing pressures, and loose particulates in the breathing hose. The loose particulates caused coughing in human-subject tests. One MSA Life-Saver 60 (20 tested) in this phase had a stuck-open relief valve. One Ocenco EBA 6.5 (50 tested) had an unattached O2 supply hose. An unexplained phenomenon occurred with two Ocenco M-20s (20 tested): low O2 flow rates preventing their successful use. Almost all of the failures noted involved units that failed their inspection criteria.

Jan 6, 2008

In the interest of safety in metal mining, the Bureau of Mines recommends: That underground metal mines be equipped with a main fan in a fireproof housing, located preferably on the surface. The fan installation should be designed to ventilate the mine adequately throughout and to permit prompt reversal of direction of air flow. Many metal mines depend for ventilation upon natural flow of air, assisted by the exhaust from pneumatic drills and by compressed air blown into the workings. Others also ventilate separate headings or sections with fans and blowers. Relatively few have o mechanical ventilating system that controls the coursing of air throughout the mine.

Jan 1, 1939

By William B. Harper

Domestic sales of carbon black sustained the upward movement for the 4th consecutive year, reflecting the increased sales of motor vehicles during the same period. Sales of carbon black in the domestic market topped 2 billion pounds for the first time during 1965 and have more than doubled the output of 20 years earlier. By far the largest user of carbon black is the rubber industry. That use accounted for more than 94 percent of the carbon black consumption with the bulk of it being used in tire casings and tubes. Thus demand for carbon black is naturally sensitive to trends in the sales of passenger cars and other motor vehicles, Manufacturers of inks, paints, plastics, paper chemicals, and food are also important users of carbon black.

Jan 1, 1967

By J. G. Kirby, F. S. LOTT

The mmber of petroleum refineries in the United States decreased during 1949 from 375 to 367 while the total crude-oil charging capacity of refineries continued to increase. A gain in the through-put capacity of 257,305 barrels daily raised the total to a new high level 6,696,300 as of January 1, 1950. The capacity of the average refinery to process crude-oil increased during 1949 from 17,171 barrels daily to 18,246. The four coastal refinery districts accounted for 178,900 barrels or 70 percent of the total capacity increase and the Illinois-Indiana- Kentucky district 57,950 barrels, or 23 percent. Slight declines in capacity were reported in the Texas Inland and the Arkansas-Louisiana Inland districts. The capacity building on January 1, 1950, 145,600 barrels daily, was less than half the amount under construction a year earlier. Most of the new construction involved enlargement of existing refineries and was confined to the East Coast and Indiana-Illinois-Kentucky districts. Two new refineries, however, were under construction, one in Oklahoma and the other in Texas. The shut-down capacity increased for the first time since 1946, and the 473,302 barrels daily reported on January 1, 1950, was the largest recorded since January 1, 1938. The only refining district showing a decline in the shut-down capacity was the Appalachian No. 2 district. The largest increases were reported in the Texas Gulf, Indiana-Illinois- Kentucky, California, and East Coast districts. The operating ratio of the petroleum refining industry, as indicated by dividing the January 1950 runs to stills of 5,483,000 barrels daily by the total installed capacity January 1, 1950, was 81.9 percent, compared with a ratio of 87.8 percent at the beginning of 1949.

Aug 1, 1950

By Willard L. Hunter

The smelting of tin slags was undertaken at the Bureau of Mines Albany Metallurgy Research Center (AMRC) to produce crude columbium-tantalum ferro-alloy as a unit operation in the production of pure columbium and tantalum oxides or chlorides. Columbium and tantalum-rich alloy was prepared during short unrelated campaigns over a total period of 12 years. Tin slags from Malaya and the Congo (Geomines) were smelted. These slags were reduced by carbon in a small, single-phase, steel-making furnace} a larger three-phase, steelmaking furnace, and a three-phase, submerged-arc furnace, In all cases depleted slags were fluid and easily tapped from the furnace. However, unless diluted by iron additions, the metal product was a viscous, high-melting, heterogeneous mixture that could be removed from the furnace only by hand rabbling.

Jan 1, 1966

By G. W. Jones

The operation of combustion engines of various types at high altitudes and other combustion processes at reduced pressures have made it desirable to determine limits of flammabilities -under these conditions. Experiments carried out by the Bureau of Mines have shown that although natural gas-air mixtures become more difficult to ignite as the pressure is reduced below atmospheric, with a suitable source of ignition the limits of flammability are as wide at 175 mm mercury absolute as they are at atmospheric pressure.

Jan 1, 1949

By V. E. Homme

Low- and high-temperature reduction techniques were employed by the Bureau of Mines in study of conditions favorable to the formation of massive titanium crystals. '1,1,2 low-temperature method, feeding molten sodium to solidified titanium lower chloride-sodium chloride, produced higher quality and high quantity crystalline metal. The percentage of crystalline titanium was increased with increasing reactor diameter, melt depth, and titanium dichloride concentration. The high-temperature technique, feed molten sodium to melts above 8000 C, producing needle-type crystals of lower quality and with less consistent results than the low-temperature method. Layers of titanium foil, sponge, fine needles, wool, and crusts of sin-tered granules were formed during the earl, -art of the low-temperature reduction, and massive crystals were produced beneath this barrier in the latter part of the reduction. Crystalline titanium having an average hardness of Bhn 76 and representing 58 percent of the total titanium was obtained. Lamellar crystals up to 1 1/2 inches long with a hardness as low as Bhn 54 were also produced. A second-stage reduction for reclaiming titanium from offgrade sponge is described. Titanium produced by this method was comparable in quality to that from sodium reduction of titanium tetrachloride.

Jan 1, 1966

By Scott W. Hazen

In recent years many mining companies have recognized that their chance for continued economic survival depends on the adaptation of technological advances in their operations. Increased productivity through new developments in mining methods and improvements in equipment has made mining and processing of lower grade ores possible. Cost analysis has produced accurate data on the costs for development, production, and processing of ore. All of these changes and cost studies have shown the necessity for increased accuracy in determining the grade of ore. Methods of estimating grade in a mineral deposit have not kept pace with the technological advances in the other areas. The same methods are in use today as in the past. Experience and judgment are major criteria of accuracy and the results are highly subjective. In 1953, as part of its research program to develop a better understanding of fundamentals of mining technology, the Federal Bureau of Mines began a sampling method research project at its Denver Mining Research Center. The basic objective of the project is to investigate sampling methods and to study the adaptation of the techniques of statistical analysis to mine sampling.

Jan 1, 1961

By P. V. Fillo

This paper describes Mohave Mining and Milling Co. methods of mining and milling manganese ore in Arizona. It is one of a series of publications prepared by the Bureau of Mines on methods and costs in various mining districts in the United States. Production of manganese ore, as such, in Arizona began in 1915. Before this time manganiferous ores had been mined primarily for silver content and used as a smelter flux. From 1916 to 1918 approximately 69,000 long tons of manganese and mangsniferous ores were mined. After World War I production dropped to almost nothing until World War II, during which period more than 24,000 long tons were produced. A lull in mangonese mining occurred after World War II, having production rates of only a few hundred tons annually through 1952.

Jan 1, 1963

By Phil Patton, Bill M. Stewart, Curtis Clark

Handling materials in underground mines continues to be a major safety problem. To help reduce materials-handling injuries, the National Institute for Occupational Safety and Health (NIOSH) at the Spokane Research Laboratory is developing, modifying, and testing equipment to replace the necessity of doing lifting tasks manually. To reduce single-event lift injuries, equipment having mechanical automatic weight sensing and balancing control was investigated. The Coleman manipulator was selected for testing. Modifications to the Coleman manipulator to make it more suitable for underground mine use included mobilization, self-containment, all-purpose gripper attachment, and support jacks. To reduce or eliminate the need to clean off manually the materials that commonly plug grizzly openings (timbers, wire mesh, roof bolts, and other debris), a track-guided pincher arm device was developed. The TGPA attaches to an impact hammer head, and the pincher arms are controlled by the operator of the hammer. Oversized rock can be broken with the pincher arms in the up position; the arms can then be lowered to grab and remove debris. Sweeping action to remove cohesive fines bridging grizzly openings is also greatly improved. This device is especially useful in recessed grizzlies. An industrial gun was tested to evaluate its effectiveness in breaking oversized rock. Boulders up to 76 cm in diameter were successfully broken to minus-33 cm. Although methods to control fly rock need to be developed, an industrial gun may be a safe and inexpensive alternative to breaking oversized rock in certain underground mining situations.

By L. C. IlsLey

Figure 1 is a reproduction of a chart recently prepared by the Bureau of Mines at its Pittsburgh Laboratory to show the Bureau's approval work in connection with electrically operated mining equipment. Nearly 27 years of approval work, covering 346 approved units, are shown on this chart. These approvals are arranged according to year of approval and the manufacturer to whom approval was granted. Forty-five manufacturers are represented, and a scheme of using various colored tabs permits the following subdivision of the equipment: Cutting machines, loading machines, conveyors, battery-operated locomotives, battery-operated power trucks, drills and drilling machines, rock-lusting machines, pumps, room hoists, air compressors,, and miscellaneous, The greatest number of approvals granted to a single manufacturer is 80; the next highest is 65, and the third is 49. Several manufacturers have been granted only a single approval. The chart shows all approvals granted for, motored equipment. Some of these units have since become obsolete, and a few are used to a very limited, extent if at all.

Jan 1, 1941

By A. Wahab Khair, W. M. Devilder

"This paper presents an analysis of fragment size distribution and characteristics of fracture surface in coal cutting using a rotary coal cutting simulator. Coal cutting by a drum type continuous miner was simulated in the laboratory. A series of tests along both the face and butt cleat direction of coal under different operating and in-situ conditions were performed. In each experiment the cut surface was photographed microscopically and the coal cuttings were collected and sized. Data were used to show how and to what extent various parameters effect size distribution of the coal cutting and how this correlates with the characteristics of the fracture surface. This study resulted in establishing a number of distinct correlations between the size distribution and fracture surface. These correlations were primarily based on the degree of interaction between adjacent bits and the amount of bit-coal interaction taking place on the cutting path. Some of the major results of this study are as follows:Zones of bit-coal interactions proved vital toward understanding the effect the conical bit has on the fragmentation process. This in turn led to the identification of areas which are responsible for the production of fines and generation of respirable dust.The various parameters employed in the coal cutting experiments which showed a strong effect on the coal fragment size distribution were: bit type, bit spacing, depth of cut, in-situ stresses, and cleat orientation. Bit angle and cutting head velocity exhibited the least effect and no correlation was established.From this study it is obvious that the key to achieving efficient coal fragmentation is to limit the degree of bit-coal interaction that takes place throughout the bit path while causing maximum interaction between adjacent bits. Accomplishing this not only increases the percentage of large fragments produced but limits the amount of secondary crushing that takes place in the bit path thus resulting in decreasing fines and consequently, the amount of respirable dust generated.Over 2,000 continuous mining machines (introduced in the 1950's) equipped with conical bits or point attach bits account for well over half of the United States' production from underground coal mines. Today, competition in the coal industry has increased, due mainly to coal market conditions and legal restrictions, thus placing an emphasis upon increasing production, efficiency and health/safety of the workers. Mine operators are always interested in finding the most efficient performance of continuous mining machinery to produce the largest amount of size of coal at the lowest cost. An increase of fine material sent to the cleaning plant can seriously overload the plant to the extent that plant efficiencies deteriorate significantly (1). Also, the difficulty and expense of cleaning very small particles often cannot be done economically and thus, thousands of tons of coal are sent to the refuse pile because of costly or ineffective cleaning facilities. It has been said, ""the efficient extraction of coal or rock implies breakage into a size range that contains a minimum quantity of very small sizes"" (2). All known fragmentation theories concur that more fragmentation requires more energy (3). So, the importance of reducing fines is already evident from an outlook upon efficiency.Now, let's consider another view point., duet generation."

Jun 1, 1988