Search Documents

By Richard F. Hewlett

Numerous populations of assays have been simulated for a range of assay values representative of low-grade mineral deposits to facilitate the study of problems encountered in evaluating these deposits. Analysis of these simulated populations of assays (obtained by using statistical probability models for the simulation) makes possible the quantification of the effects of (1) various composite assay intervals, (2) ore reserve computational methods, (3) uneven assay intervals, and (4) various cutoff grades on both the precision and the accuracy of the estimated average grade and tonnage of ore.

Jan 1, 1964

By Frank J. Wiebelt, Spangler Hicker

The Iron Mountain investigations were part of a comprehensive program for making a national inventory of raw materials used in the production of steel. A tentative program of core drilling by the Bureau of Mines was set up for exploration of more promising iron deposits. Iron Mountain was selected as worthy of investigation because it could serve as a potential source of ore for the war-created steel plant at Fontana, Calif. The deposits were reported on by an engineer in October 1943. The purpose of the project was to determine the lateral and vertical extent of ore bodies and to obtain accurate material data on them.

Apr 1, 1948

By Raymond W. Hiteshue, Sam Friedman, Paul Dobransky, Robert Madden

A hvab coal was carbonized in a closed system at 600 ° C and 40 to 1 , 200 psig to produce a high- Btu gas and char . By retaining the volatiles within the system, it was possible to virtually eliminate production of tars and oils . Depending on pressure and residence time , yields of combustible gases (72 to 92 percent methane ) amounted to 4,000 to 6,000 cubic feet per ton of maf coal and gross heating values of these gases varied from 830 to 960 Btu per cubic foot . Yields of char (maf ) were about 1,600 pounds per ton of maf coal . Increased residence time favored production of gases but reduced their heating values , whereas increase in pressure resulted in somewhat higher heating values and lower production . Similar effects were observed from the carbonization of a low- temperature tar . If these results could be translated to an economical carbonization process for producing high- Btu gas from coal , the demand for coal could be expanded by 40 to 50 million tons per year . Because of large yields of char , a process of this type would obviously have to be integrated with coal - fired power plants . Fortunately , operations could be conducted at essentially atmospheric pressure as product gas under this condition can be obtained in satisfactory yields and with good quality .

Jan 1, 1964

By J. C. Edwards

To have the capability to predict the development of localized spontaneous heating within a porous coalbed that is subjected to forced air ventilation or in an otherwise quiescent environment in which buoyancy develops, the Bureau of Mines developed three time-dependent mathematical models, which were used to calculate the temperature increase associated with chemisorption of oxygen by the coal. In each model, spontaneous heating is driven by an Arrhenius first-order reaction between the oxygen and coal. Two models are two-dimensional, and one is one-dimensional. In the first two-dimensional model, a constant-velocity forced convection airflow is specified; and in the other, buoyant flow is allowed to develop in the absence of forced convection. The third model evaluates the airflow from Darcy's law and a specification of the pressure at the surface of a one-dimensional porous coalbed. Numerical computations demonstrated how each model could be used to predict the onset of spontaneous heating when the porous coalbed was subjected to constraints of an imposed internal heat source or a high temperature airflow. The effects of particle size and coalbed compaction upon spontaneous heating were examined with the third model.

Jan 1, 1990

By Roy T. Sorensen

The Bureau of Mines has investigated the recovery of cell-grade alu-mina by RCI leaching of calcined kaolin in the alumina miniplant at its Boulder City (NV) Engineering Laboratory. Classification and thickening were used for separating aluminum chloride leach liquor from the siliceous residue generated in the acid leaching step of the clay-HCI process. Coarse solids were classified from fines at 115 mesh and countercurrently washed in three additional spiral classifiers. Fines were treated in a conventional five-thickener, countercurrent decantation circuit. When this method was applied to the solids-liquid separation of slurry from RCI leaching of minus lO-mesh calcined kaolin, 75 pct of the residue reported as classifier sands and 25 pct as thickener underflow. Predicted individual classifier and thickener area requirements were 6 and 25 ft2/tpd, respectively. Total thickener circuit flocculant requirement was 2.4 lb/ton solids. Aluminum chloride pregnant liquor was produced that analyzed 8.4 pct A1203 and contained more than 97 pct of the alumina in the liquid phase of the slurry. Bench-scale settling tests were used to correlate fines content of leach residue to thickener area and flocculant requirements.

Jan 1, 1983

By C. M. Mason

The methods currently used by the Bureau of Mines to evaluate the sensitivity, strength, incendivity, gaseous products, and physical properties of explosives and hazardous chemicals are described. Included are the tests used to evaluate explosives which arc certified as permissible for use in underground coal mines.

Jan 1, 1972

By John Nagy

The effect of low percentages of methane (0 to 5 pet.) in an air atmosphere on spark initiated explosions of coal dust was investigated. With low dust concentrations (0.1 to 0.4 oz./cu, ft.), small amounts of methane increase the explosion pressure; with larger dust concentrations (0.5 to 2.0 oz./cu. ft.), small amounts of methane decrease the explosion pressure. The rate of pressure rise of a coal dust explosion increases with increase in methane concentration; about 3 to 4 pct. further addition of methane yields a decrease in the rate of pressure rise. Convection currents created by the air or gas blast used to disperse dust produce an increase in explosion pressure and rate of pressure rise. The minimum explosive concentration of the coal dust decreases about linearly as the concentration of methane increases from 0 to 5 pct. The explosion pressure increases linearly as the initial pressure within the chamber increases. Similarities between coal dust and methane explosions are indicated, INTRODUCTION During coal mining, methane occluded in coal or adjoining strata is liberated into the mine atmosphere,4 Normally, the methane is diluted and swept away by the ventilating air. Under some conditions, through accidental disruption of the ventilation system, sudden outburst, or because insufficient fresh air is supplied to a working place, low percentages of methane may be present during mining operations. If it is permitted to accumulate, methane itself presents an explosion hazard; its limits of explosibility arc approximately 5 and 15 pct. The effect of low percentages of methane on the explosibility of coal dust was studied to provide a broader understanding of the hazards of ignition and explosion and thus to facilitate development of control

Jan 1, 1961

By John M. Gomes

A two-phase molten halide-silicate technique for extracting tungstic oxide (WO3) from scheelite (CaW04) and wolframite [(Fe, Mn)W04] was investigated. The halide phase extracted over 99 percent of the was, whereas the lower silicate phase retained about 90 percent of the calcium, iron, or manganese oxides. The most efficient extraction and separation of tungsten from scheelite was accomplished at 1,080° C in a molten system containing, in mole-percent, 9 calcium tungstate (CaW04), 42 sodium chloride (NaCl), 28 sodium fluoride (NaF), 17 sodium metasilicate (Na2SiO3), and 4 alumina (Al2O3). Wolframite was also treated at 1,0800°C; the molten system contained, in mole-percent, 11 (Fe, Mn)W04, 74 NaCl, and 15 Na2 SiO3.

Jan 1, 1968

By J. D. Ramsdell

The study described in this report was undertaken to obtain information on the character and effect of antimony additions to titanium. The availability of high-purity, low-hardness titanium metal, resulting from fused-salt electrorefining techniques, permitted a reassessment and evaluation of the physical behavior of titanium-antimony alloys. Alloys, based on several grades of titanium containing up to 10 percent antimony, were arc-melted and processed to sheet by hot and cold rolling. Properties and characteristics were evaluated by hardness tests, hot and cold rollability, annealing treatments, metallographic examination, and tensile tests.

Jan 1, 1960

By V. T. Dow

In April 1957 the Bureau of Mines instituted a reconnaissance of titanium-and zirconium-bearing heavy sandstone deposits in the Four-State area of Utah, Wyoming, New Mexico, and Colorado. This report summarizes the study. Eighty-two deposits or groups of deposits, containing an estimated 27,920,000 tons of titaniferous sandstone, were examined in the Four-State area; 16 in southern Utah, 19 in Wyoming, 33 in New Mexico, and 14 in southwestern Colorado. The 16 deposits examined in Utah contain an estimated 1,043,000 tons with an average grade of 17.98 percent TiO2, 5.67 percent ZrO2, 20.98 percent Fe, and 0.09 percent equivalent Th02. The 19 deposits investigated in Wyoming are estimated to contain 21,873,000 tons of titaniferous sandstone having a weighted grade of 5.22 percent 702, 0.55 percent ZrO2, 24.8 percent Fe, and 0.01 percent equivalent Th02.

Jan 1, 1961

By John M. Gomes

Two molten salt systems were evaluated as electrolytes for the repetitive recovery of tungsten from tungsten oxide (W03) made by calcining commercial-grade ammonium paratungstate. Using a sodium chloride-sodium fluoride-potassium aluminum tetrafluoride electrolyte at 800° C, 1 pound of 99.8 percent tungsten was recovered for each 2.7 kilowatt-hours of energy consumed. The metal contained 1,100 ppm carbon, was in dendritic masses of spherical grains, and had an apparent bulk density of 5.41 g/cm3. T ngsten of 99.9 percent purity was won from a sodium pyrophosphate-sodium tetraborate-sodium chloride electrolyte at 1,000° C; 6.0 kilowatt-hours of energy was consumed for each pound of metal recovered. The metal contained 120 ppm carbon, was in dendritic masses of hexagonal acicular crystals, and had an apparent bulk density of 7.25 g/cm . Each metallic impurity--aluminum, calcium, copper, iron, nickel, and silicon--in the two tungsten products was 16 ppm or less.

Jan 1, 1966

By O. C. Blade

This report on the properties of motor fuels sold through service stations in the United states was made in accordance with a cooperative agreement between the American Petroleum Institute and the Bureau of Mines of the United states Department of the Interior. This paper is a continuation of a series made in cooperation with the Coordinating Fuel Research (CFR) Committee of the Coordinating Research Council (CRC). Inc. The first of this series of reports presented data on motor gasolines sold during the winter of 1935-36, and succeeding reports described motor gasolines sold during the summers and winters to and including the summer of 1941. No reports were made on motor gasolines sold during the winter of 1941-42 and during the summer of 1942. However, starting with the winter of 1942-431' the semiannual reports were resumed.

Jan 1, 1950

By V. E. Edlund

Laboratory batch flotation tests were conducted on copper converter slags to evaluate the relative merits of recovering copper from slow-cooled versus water-quenched slags. Three slags containing 1.6, 5.0, and 6.6 percent copper were used. More than 90 percent of the copper was recovered in a rougher concentrate leaving a 0.2- to 0.3-percent copper tailings when treating slow-cooled slag. Lower recoveries and higher copper tailings ranging from 0.5 to 0.6 percent copper were obtained from quenched slag. Grindability studies were made on the respective heat-treated slags. Quenched slags proved more difficult to grind than slow-cooled slags. Cost studies showed that quenched slags can be treated at slightly lower cost than slow-cooled slags. However, the cost advantage of processing quenched slags is more than offset by the higher copper recoveries obtained from slow-cooled slags.

Jan 1, 1971

By W. W. Adams

"A recent paper prepared by the writer summarized the results of an analysis of the accident records of 34 metal mines for the calendar year 1925. The present paper summarizes the results of a similar analysis of the accident records of 59 coal mines for the same year. This summary is based upon reports furnished to the Bureau of Mines, Department of Commerce, by operating companies that par¬ticipated in the National Safety Competition of 1925.The purpose of the Competition was to establish the lowest accident-severity rate, thus showing the smallest loss of time from accidents in proportion to total number of man-hours worked. The reports covered all lost-time accidents that occurred during the year, that is, all accidents that disabled an employee beyond the day or shift on which the accident occurred. Detailed information for each of the 59 coal mines is given in the appended table. Each mine employed at least fifty men underground; over half of than employed more than 200 men underground. Hence the accident records should be typical of those of large-scale mining operations in general where the company is devoting special attention to accident-prevention work. The mines covered by the reports are situated in eleven States: Alabama, Illinois, Indiana, Kentucky, Maryland, Ohio, Pennsylvania, Tennessee, Utah, Washington, and West Virginia.A tabulation of the reports covering the 59 mines showed an accident-frequency rate of 123 per million hours of ""exposure* and an accident-severity rate of 10.214 per thousand hours of exposure3. The total volume of exposure or employment was 29,117,561 hours, representing the equivalent of work of 12,000 men for three hundred 8-hour shifts. The records covered employment and accident above ground as well as underground, although they did not include stripping or open-pit mining. Accidents during the year resulted in 33 deaths, 1 permanent total disability, 28 permanent partial disabilities, and 3,510 temporary injuries. These accidents represented a loss of tine equal to 297,417 man days. In arriving at this lost-time equivalent, each fatality and permanent total disability was weighted at 6,000 lost days (see footnote 3), as specified in the scale adopted by the International Association of Industrial Accident Boards and Commissions; permanent partial disabilities were weighted according to nature of injury, in accordance with the scale adopted by the :Board; temporary injuries were weighted according to the actual number of calendar days during which the employee was incapacitated as a result of the injury."

Nov 1, 1926

The panic bars (and associated linkages and electrical circuitry) that are defined in this document are a machine operator-actuated control for the emergency deenergization of the tram motors on self-propelled, electric and diesel face equipment; including haulage equipment such as shuttle cars. There are nine basic types of panic bars (and several variations) that are recommended in this document, but all of the panic bars are characteristically of the ?fire door? type that is frequently encountered on outside exit doors of many public and some commercial buildings. It is also the intent of the following panic bar designs that, when emergency brakes are added to the face equipment machinery for which they are required, that they be designed and hooked up so that actuation of the panic bar will result in automatic application of the emergency brakes (immediately following the deenergization of the tram motors). The following panic bar design requirements are a restatement of the proposed requirements defined in the Federal Register, requirements cited in "Guidelines for the Design and Installation of Devices for Deenergization of Self -Propelled Electric Face Equipment/Automatic Emergency Brake s II by C. E. Lester and J. D. Greenhalgh of MESA, and Bendix recommendations that were formulated as a result of discussions with personnel at the various machine manufacturers and underground coal mines that we surveyed, discussions with G. L. Judy (our consultant), etc:

Jan 1, 1974

By W. S. Sanner

This report describes the commercial application of the launder screen in anthracite-industry fine-coal cleaning operations. No new device, the launder screen has been used since the early part of the present century to size, screen, classify, and deslime the fine-anthracite sizes (Buckwheat Nos. 1 through 5) recovered by "river-coal" men dredging along streams draining the anthracite fields. The launder screen is stationary, has no moving parts, requires ample water for operation, and can be constructed economically on the job. Essentially, it consists of a wooden trough with baffles placed through its width to form a well system. The wells are covered by fine-mesh woven-wire screening. Each well is tapped with a number of orifices, and the hydraulic suction head developed in this manner removes high-gravity fines and slimes through the screening as underflow to waste. Material retained on the screen surface discharges as overflow product.

Jan 1, 1954

By Albert L. Toenges, Henry E. Dekay, James N. Scudder

Support of the immediate roof in coal mines is essential for their safe operation, and timbers are the most common means of support. Their effectiveness depends upon their resistance to decay. The theory has been advanced by some mine operators that rock dust, which is applied to ccal-mine workings to prevent propagation of explosions, accelerates the decay of mine timbers. As the results of part 1 of this study were inconclusive, the study was continued. Its principal objectives are: 1. To determine the effect of rock dusting upon decay of mine timber. 2. To compare the extent of decay of timbers in two mines in which underground conditions are similar. 3. To determine the loss in strength of the timbers after exposure to mine atmosphere. The studies were carried on in the Crucible mine of the Crucible Fuel Co. where the first part of this study was made, and in the Isabella mine of the Weirton Coal Co. The mines are on the Monongehela River and are adjacent.

May 1, 1943

By Jr. Hazen

Relationships that may exist between assays and sample interval lengths when using unequal sample intervals in mine sampling have been investigated as part of the larger research problem of adapting statistical methods to the analysis of weighted average grades. The theoretical relationship between the amount of difference in the weighted and unweighted average grade of ore and the size of the correlation coefficient between assay value and sample interval length was found to be linear. Numerous examples of actual field sample and assay data, which have been obtained by using unequal sample intervals, are documented, and the differences between weighted and unweighted average grades of ore and the correlation coefficients between assays and sample interval lengths have been computed and plotted on graphs. Differences between these actual field data and the expected theoretical linear relationship are examined. It is hypothesized that the use of unequal sample intervals in mine sampling is, in fact, stratified sampling in a statistical context. The sampler establishes stratification by selecting unequal sample intervals on the basis of differences in lithology, changes in rock type, characteristics of mineralization, or differences in metal content. Statistically} methods currently used in mine sampling, involving unequal sample intervals, fail to consider differences in the inherent variances in grade of ore within the various strata established by using unequal sample intervals. Consequently the strata are sampled with different precision. This difference in precision of sampling between strata may account for much of the deviation between the plotted points representing actual field sampling data and the theoretical linear relationship between the amount of the difference between weighted and unweighted average grade of ore and the size of correlation coefficient between assays and sample interval lengths.

Jan 1, 1966

By M. G. Zabetakis

Benzene and toluene are the first two members of an important homologous series whose general formula is CnH2n-6. The members of this series differ in composition from benzene by some integral multiple of CH2; they can all be prepared in the laboratory by the Wurtz-Fittig, Friedel-Crafts and Grignard syntheses. Because 'of the industrial importance of these-hydrocarbons, the limits of flammability of eight members of the series have been determined at 100° C.-(A temperature of 1000 C. was chosen because the determination of the upper limit of flammability of p-cymene requires an apparatus temperature. of at least 90° C. As elevated temperature data are available for other combustibles at 100° C. but not at 90° C., all data were taken at 100° C. in order to obtain comparable results.) Minimum ignition temperatures of these combustibles have been determined at laboratory-pressures.

Jan 1, 1951

By A. Gene Collins

The Bureau of Mines undertook research to determine the bromide and iodide content of Mississippi and Alabama oilfield waters of the Tertiary and Cretaceous Period to determine genetic relationships of the ions, to determine their origin, and to determine their genetic relation to petroleum. The 280 samples were analyzed after a pretreatment to remove interferences. The iodide was oxidized to iodate and was titrated with thiosulfate. The bromide was oxidized to bromate and was determined iodometrically. A computer was used to calculate the correlation coefficients of iodide to bromide and to other ions. The other ions are sodium plus potassium, calcium, magnesium, chloride, bicarbonate, and sulfate. The mineral content of the samples ranged from 52 to 1,760 mg/l for bromide and from 2 to 65 mg/l for iodide. The mean bromide-to-chloride and iodide-to-chloride ratios were 0.0065 and 0.0002. The correlation coefficient matrix and linear plots indicated a definite bromide-to-calcium relationship for the brines investigated.

Jan 1, 1967