Search Documents

By B. W. Gandrud

To say that the treatment and handling of the "fines" is the most difficult phase of coal preparation is probably an understatement of facts. It is the fine sizes from about 1/16-inch to 0 that are mainly responsible for the inescapable sludge and slurry problems at plants using wet methods of preparation. Sludge and slurry are a problem from the standpoints of both cleaning and dewatering. They cannot be cleaned satisfactorily by "gravity" methods, which are used so extensively on coarser Sizes, due to the fact that fine sizes, particularly from 65-mesh to 0, do not follow the same laws of settling as do the coarser sizes. Although fine sizes are cleaned more successfully on wet-wash tables than in jigs, even tables as usually operated in coal-preparation plants fail on sizes below 100-mesh. As to other phases of the, sludge and slurry problem, wet coal preparation plants are almost universally beset with troubles in connection with the recovery and dewatering of the fine sizes from about 14-or 20-mesh to 0. The sizes finer than 100-mesh further complicate the problems in a wet preparation plant by their tendency to stay in suspension and build up a troublesome load of solids in the circulating water. In order to prevent too much trouble from this source, it is, customary at most plants to bleed a fair-sized stream out of the circulating system continuously and replace it by addition of fresh make-up water. The slurry water withdrawn from the circuit is usually run to waste, in which case it carries with it a considerable amount of fine coal, thus increasing the "washer loss." Another evil results from wasted slurry water in that quite often it finds its way into creeks and larger streams, creating stream-pollution problems.

Jan 1, 1948

By S. H. Ash

A CLAY, sand, and gravel deposit known as the "buried valley" of the Susquehanna River is situated in the Northern field of the anthracite region of Pennsylvania near Wilkes-Barre. The presence of this buried valley and the uncertainty regarding the extent and physical condition of the water-bearing valley-fill deposits have made great care necessary in mining operations to avoid breaking the strata between the mine workings and the valley-fill deposits to the extent that inundation of the mine workings would follow. The principal factor that threatens to cut short the life of the anthracite industry, to curtail production, and to affect the economic structure of the people and business dependent on anthracite for their livelihood is inundation of anthracite mines (6,7).3

Jan 1, 1950

By Floyd R. Anderson

Noise control of existing pneumatic drills is difficult and runs into cost, performance and weight penalties. A need exists for a start-from-scratch approach for quiet pneumatic rock drills. The designs based on Leavell Principles which has been successfully used in demonstrating a quiet and vibration free paving breaker, is the concept chosen here. This report shows the feasibility of a quiet stoper for drilling roof bolt holes in coal mines. The work is directly applicable to pneumatic percussive rock drills. The report shows an oscillator based on patented Leavell concepts which results in a vibration free tool and noiseless exhaust. Dynamics of the oscilator is analyzed. Independant rotation of drill rod is provided by an air motor (screw expander) and flushing of cuttings is accomplished by an air ejector in a compact lower housing. The feasibility of no exhaust noise, low drill machine noise, and vibration free casing is discussed.

Jan 1, 1977

By Stanton L. Tainter

As a part of a wartime program to aid in the development of known ore bodies and in the discovery of hitherto unknown deposits of strategic minerals, the Bureau of Mines investigated the feasibility of diamond-drilling the Christmas copper deposit, in Gila County, Ariz., to increase the reserves of milling ore. Upon recommendation of the examining engineer, drilling was begun in September 1942, from the bottom (770) level of the mine. One month later, in cooperation with the Bureau, the Federal Geological Survey started geologic mapping of the mine workings. Since extensive and costly development would be required, the War Production Board concluded that ore below the bottom level could not be mined at that time because of the wartime shortages of equipment and man-power. In January 1943, drilling was moved to the 300 and 400 levels to locate reserves readily accessible for continued production of fluxing ore. This drilling, which was under the supervision of L. G. Marshall, was completed in January 1944.

Jan 1, 1948

By John A. Johnson

Conclusions regarding the use or omission of stemming in blasting have not peen reached, pending completion of all aspects of this investigation. The results from the dust phase of this study on six classes of stemming prove that the kind of stemming affects the amount of dust produced from blasting. In previous work at the Mount Weather testing adit it was demonstrated that blasting produces the highest dust concentrations of any of the mining processes.5/ Under the conditions prevailing at the Mount Weather testing adit, the average of all rounds having a break of at least 95 percent showed that the least amount of dust was produced when no stemming was used.

Jan 1, 1940

By John A. Johnson

Conclusions regarding the use or omission of stemming in blasting have not peen reached, pending completion of all aspects of this investigation. The results from the dust phase of this study on six classes of stemming prove that the kind of stemming affects the amount of dust produced from blasting. In previous work at the Mount Weather testing adit it was demonstrated that blasting produces the highest dust concentrations of any of the mining processes.5/ Under the conditions prevailing at the Mount Weather testing adit, the average of all rounds having a break of at least 95 percent showed that the least amount of dust was produced when no stemming was used.

Jan 1, 1940

By P. M. BIDDISON, G. G. Oberfell, George A. Burrell

The Bureau of Mines is conducting a series of investigations, with a view to ascertaining the most efficient methods of obtaining gasoline from petroleum and natural gas. This report deals with a method of extracting gasoline from natural gas by absorbing the gasoline in oil and subsequently separating it from the oil by distillation. The process is quite different from those of compression and condensation which have been used for a number of years for extracting gasoline from casing-head natural gas, and has not heretofore been described in the literature. MANUFACTURE OF GASOLINE FROM CASING-HEAD GAS. The extraction of gasoline from casing-head natural gas by compression and condensation methods has become a large and lucrative industry in this country. In the year 1915 about 65,000,000a gallons of gasoline prepared by these methods was placed on the market. In addition, in marketing this gasoline, at many plants an equivalent quantity of naphtha was blended with the gasoline, thereby utilizing for automobile fuel and other purposes a large quantity of naphtha that otherwise would have been unsuited for these purposes. The increase for the year 1915 over 1914 was about 22,000,000 gallons. For the year 1916 the production should be more than 100,000,000 gallons. The quantity of casing-head gas treated in the year 1915 by compression and condensation methods amounted to about 24,000,000,000 cubic feet; the average yield of gasoline was 2.57 gallons per 1,000 cubic feet. b This casing-head gas represents natural gas that formerly went largely to waste; hence the process represented a distinct and important step in the utilization of the natural gas produced in this country.

Jan 1, 1917

By William C. Cooley

[Data from t.-raturs on each hydr,ne has been assembled on the- data sheets whichw6ed in this Appandin. Dai_iis are provl_ od for ::amines or hydraulic s-ctions in the USSR (TDPhw~s), 8 in ASR (Kuzbass) , 1i-gin i, 1 in 7in China, i in Japan, and l in C~n- i.Ata sheetsiov tion prepared for mines in New Zealah_~sddered very rele¬ vant, nor forf !aA of information. In aW,!~.F in : --- C=SR for tiara ShoeLS ara 1palAwdl satinieral mines have operac- ~ - re Manned about which very limited data exist as folloos:]

Jan 1, 1975

By R. E. Heithecker, D. B. Taliaferro

"INTRODUCTION Recovery of core specimens from subsurface formations and their subsequent analysis are important aids in efficient development and operation of oil and gas fields. Gore specimens first were obtained mainly for the geologic information they revealed; now they are analyzed to determine many of the physical characteristics and conditions of the subsurface formations as well. Cores recovered from the producing formations may be analyzed for porosity, permeability, oil content, ""connate"" water content, and other physical and chemical properties of the formation, all to the end of furnishing enough data for making reliable estimates of the quantity and avail¬ability of oil and as within a reservoir and in devising efficient means for their withdrawal.Examination of bottom-hole samples of oil gives valuable information concerning the amount of gas in solution in the oil within the reservoir and the resultant shrinkage of the oil when the gas is released. Producing characteristics of reservoirs nay be determined by means of subsurface pressure and temperature gages and measurements male at the wellhead; however, unless reliable core analyses are available, these data have only limited use in any quantitative study of reserves. In such a study the quantity of oil, gas, and water contained in a unit volume of the reservoir formation is extremely important. Although reliable methods of analyzing cores have been developed and the data thus obtained are valuable, their applications become more limited or reservoirs at higher temperatures and pressures are discovered. This condition results almost entirely from the fact that in recovering a core from a formation of high pressure and temperature by present methods a large part of the fluid content of the core is lost or contaminated to an unknown extent. For a number of years most petroleum engineers have held that if this loss and contamination of the fluid content of a core were eliminated, the value of core analyses would be increased greatly."

Nov 1, 1939

By J. T. Popp, C. M. McCulloch

This Bureau of Mines study reviews the geological factors that affect methane in the Beckley coalbed in southern West Virginia, including overburden, coalbed structure, type of and changes in lithology above and below the Beckley coalbed, and presence of fractures in the coal and rock adjacent to the Beckley. Depending on the depth, the Beckley coalbed emits from 216 to 520 ft3 of methane per ton of coal mined, and the Bureau estimates that methane emission in a deep, extensively developed mine in this area may exceed 3,000 ft3 per day per ton of coal mined. Average face cleat and butt cleat trends in the Beckley coalbed measured underground are N 33° W and N 53° E, respectively. Close cleat spacing con- tributes to the friable nature of the Beckley and provides easy movement for methane and water. Because rider coals, splits, and carbonaceous shales may contribute methane to mine emissions, predictions of methane emission based on gas content of the Beckley coalbed alone may be conservative. Beckley coalbed reserves in the study area are 234 million tons. The gas content of the Beckley coalbed averages 407 ft3/ton, and the coalbed gas reserves are 108 billion ft3.

Jan 1, 1976

By George A. Page, Hewitt Wilson, Vance S. Cartwright

"Purpose of InvestigationThe process of removing solid material from liquid suspensions has been studied at the Northwest Experiment Station, United States Bureau of Mines, in cooperation with the University of Washington, as part of a general program to investigate the dewatering of Pacific Northwest plastic kaolins, which is difficult by ordinary filter-pressing methods. The present paper is a progress report of the work began by Vance S. Cartwright in 1928 and continued in 1931 and 1932. Spray evaporation is believed to be valuable for the following classes or grades of clay and clay mixtures:(1) Highly colloidal, plastic-type clays, which release their mechanically attached water with difficulty; (2) clays prepared for shipment in pulverized or powdered condition; and (3) synthetic, ceramic, porcelain, and tile mixtures prepared as aqueons suspension, dried and pulverized before molding. Dilute suspensions can be dewatered by spray evaporation to produce concen-trated casting slip or plastic clay with a lower water content.The most common dewatering method used in preparing powdered kaolin for the market comprises the following steps: Reduction of the water content by filter-pressing from approximately 75 percent in the thick ""slip"" condition to about 30 percent in the condition; further reduction of the water in the filter-press cakes by heat to about 5 percent; and pulverization of the dried cakes in hammer or dust. These three steps can be simplified to a single process by spray evaporation."

Jan 1, 1935

By E. J. Babcock, W. W. Odell

The Bureau of Mines since its establishment has always taken an active interest in the utilization of lignite and in the development of the lignite dep'osits of the United States. Extensive lignite fields occur in the west central States, notably in North Dakota, Montana, Wyoming, Colorado, and Texas; there are smaller areas in several other States, some of which are widely separated. The total area of the deposits and the total amount of lignite in these several districts are so enormous that the economic value is seldom recognized. To the people of ·the west and west central regions, however, the larger utilization of lignite, in whatever form it may be, is of fundamental importance, and any new methods or uses that promise to open these great lignite fields for more general and more efficient use deserve careful study. Although these lignite deposits underlie areas of thousands of square miles, their development and general utilization has been rather slow. This is no doubt partly because many of the districts are not thickly settled or highly developed in manufacturing industries, but is largely because lignites, from their peculiar physical and chemical characteristics, are low-grade fuels. Most of the lignites in these areas are imperfectly developed coals; many have a more or less woody structure; some belong to the brown-coal type; and others are darker, denser, and more homogeneous, approaching subbituminous coal. The people living in the regions in which these vast deposits occur, especially in the west central part of the United States, are vitally interested in every effort toward bettering lignite as fuel and aiding its wider utilization.

Jan 1, 1923

By Richard L. Unger

The Crewstation Analysis Programs (CAP) is a package of computer programs that can be used to analyze some human engineering aspects of crewstation design (such as visibility and illumination) that have particular significance in underground mining. It was developed under the U. S. Bureau of Mines (USBM) Health, Safety and Mining Technology program at the Pittsburgh Research Center, Pittsburgh, PA. This manual describes the steps necessary to collect data in the laboratory to develop luminaire profiles for the CAP illumination analysis. It also describes how the CAP Illumination Model calculates illumination. 1.1 How CAP Calculates Illumination 1.1.1 Background -CAP currently includes assessments of visibility and illumination in the surrounding work area. The advantage of using computers for these types of analyses is that many design iterations can be tested quickly and efficiently to learn the effects of changes. This reduces the need for expensive testing using physical mockups. Another advantage is that design ideas can be tested in situations where it would not normally be possible. For instance, the effects of modifications to a lighting system or canopy design on visibility could be tested while the machine remains in service.

Jan 1, 1994

By W. Dan Walker

In recent years the Federal Bureau of Mines tested and approved four new types of self-contained breathing apparatus and a facepiece designed for use with the McCaa 2-hour self-contained oxygen breathing apparatus. The Bureau also developed and perfected a battery-powered lifeline telephone for use in mine rescue and recovery operations. Some of this equipment is described in Bureau of Mines Information Circular 7413.4/ This publication is a revision of information Circular 7413 and presents pertinent information on more recently developed mine rescue equipment. The breathing apparatus described herein are 1/2- and 3/4-hour sell-contained types of much simpler design than the conventional 2-hour self-contained oxygen breathing apparatus ordinarily used by mine rescue crews; however, it is just as important to select rescue crews carefully and to train them properly in the use, care, and limitations of the newer types of apparatus as well as the older, established types, if the newer types are to be used safely. The Bureau of Mines recommends that 1/2- and 3/4-hour self-contained breathing apparatus be used only as auxiliary equipment in mine rescue and recovery work and that the capabilities and limitations of the apparatus should be well understood by those who wear the equipment.

Jan 1, 1957

By Frank Parrish

THIS REPORT by the Federal Bureau of Mines presents data on water-supply wells used by waterflood operators in North Texas and shows the distribution of permeable source sediments. Averages of well characteristics, including static fluid levels, working fluid levels, net thicknesses, producing rates, and depths, are presented and discussed. Essentially all water used in waterflooding is mineralized water from consolidated sediments. This study is concerned with the geology and distribution of these mineralized source sediments, whereas previous work in this area was predominantly a study of shallow sources of potable water. Tables, isopachous maps, and electric-log cross sections are included to describe the several source aquifers. In general, water-producing capacity increases with depth of the sediments. Wells completed in Cretaceous sediments 82 to 600 feet deep yield 50 to 600 barrels of water daily, whereas those completed in Pennsylvanian sediments 360 to 4,110 feet deep yield 100 to 7,000 barrels daily. Although deeper formations are used where oil and water are produced conjunctively and where large withdrawal rates are required, insufficient well data prevented mapping of deeper formations.

Jan 1, 1961

By Edwin B. Cook

Studies of flame and combustion phenomena at the Bureau of Mines have been facilitated by computer evaluation of the thermodynamic properties of gases formed by constant-pressure burning.4 5 This report is the sixth of a series6-10 presenting results of such calculations; it deals also with constant-volume deuterium-air flames.

Jan 1, 1961

By L. F. Willmott

The Bureau of Nines at Morgantown, W. Va., has been investigating, on a pilot plant scale, various methods of gasifying bituminous coal with oxygen and superheated steam to produce synthesis gas, as part of the broader program of finding new uses for coal. Differences in the pressure gasification methods used have depended on differences in the manner in which the pulverized coal is fed to the gasifier. One of the methods of feeding the coal that was investigated was the continuous, integrated coal-water slurry system. Goal and water were first mixed to produce a slurry; then the slurry was pumped through a heated coil. to evaporate the water fraction; the resulting steam was superheated, and some of it was separated so as to adjust the ratio of the residual steam to the coal fraction and make the resulting mixture suitable for partial combustion with oxygen in a pressure gasifier. Both before and during this reported3 developmental work it was necessary to make an extensive literature search into the technology of aqueous slurries in order to establish design criteria for the pilot plant and to correlate results of various phases of the work with that of other investigators, The pilot work coincided with the commercial development of a long-distance pipe- line for the transportation of coal as a coal-water slurry, and this fact tended to broaden the scope of the pilot plant work and the extent of the literature search. This bibliography is the compilation of the material that was collected.

Jan 1, 1963

LARGE-SCALE production of zirconium by the Northwest Electrodevelopment Laboratory of the Bureau of Mines at Albany, Oreg., is an anomaly that justifies some explanation. The reduction of titanium tetrachloride with magnesium in an inert atmosphere, as perfected by Dr. W. J. Kroll before 1940, aroused renewed interest in zirconium, and in 1945 development work on this metal was initiated at Albany under Dr. Kroll's technical direction. Preliminary results were promising, and in February 1947 a pilot plant with a weekly capacity of 60 pounds of zirconium-metal sponge was put in operation. Shortly thereafter the Oak Ridge National Laboratory of the Atomic Energy Commission requested production of 1 ton of zirconium-metal sheet, with the provision that it have a low hafnium content. The Bureau of Mines was furnished with a. supply of Brazilian baddeleyite ore, containing less than 1 percent hafnium with respect to zirconium, from which was made about. 2,700 pounds of relatively low hafnium zirconium sheet of 0.080-inch thickness for test purposes. This was accomplished by melting zirconium sponge in a graphite crucible, hot-rolling the ingot in an iron sheath, and finishing by cold rolling. Concomitantly the Oak Ridge Laboratory developed a method for separating hafnium from zirconium; and, in cooperation with the Atomic Energy Commission and the Bureau of Ships of the Department of the Navy, a, larger pilot plant was erected to produce zirconium from very low hafnium zirconium tetrachloride furnished by the Commission. Pilot-plant work on producing zirconium tetrachloride from zircon sand and baddeleyite was discontinued. Production of zirconium sponge in the larger pilot plant of 500 pounds per week capacity was begun in June 1949.

Jan 1, 1956

By Alden H. Emery, J. J. Forbes

"IntroductionThe data contained in this paper were collected during the course of an investigation which covered 15 representative coal mines in 6 coal-mining States. The purpose of the investigation was to determine by atmospheric sampling how much dust was raised into the air during the various operations of coal mining, such as undercutting with machines, loading coal by hand, and transporting it from the working face to the surface. The data thus obtained were considered from two angles - namely, the possible physiological effect of inhalation and the explosion hazard of the dust. No attempt will be mode to discuss the former factor in this paper.CONDITIONS OF MININGThe mines in which this investigation was conducted were considered representative, and it is believed that the results obtained will suffice for the average dustiness encountered in most coal mines. .All of the coal mined was bituminous, from beds 30 to 120 inches thick. Only the ordinary room-and-pillar system of mining was employed. Daily production ranged from approximately 700 to 1500 tons and the men employed from 150 to 450. Coal was undercut by short-wall mining machines in all mines, with the exception of one in which pick mining was employed. Loading at the face was done by miners; none of the mines used mechanical loaders. Electric drills, both for brushing roof and for shooting coal, were commonly used although some roof work was done with jack-hammers and a. little of both with augers. Coal was hauled by motor, mule, or rope power in end-gate cars with capacities ranging from 1600 to 3600 pounds. With few exceptions, coal was won at the face by dry methods - that is to say, no water was employed fox wetting down the dust either during undercutting, loading, or transportation."

Feb 1, 1927

By John A. Burgess

The Carson Hill mine of the Carson Hill Gold Mining Corporation is at Melones, Calaveras County, Calif. It is one of the numerous mines on the Mother Lode of California. The property extends for 8,400 feet along the outcrop of that important vein system. The elevation at the haulage level is about 1,000 feet above sea level. ACKNOWLEDGMENTS Acknowledgment of assistance in the preparation of this paper is made to Frank Wagner, underground superintendent; Max Petersen, engineer; and Homer Mann, assistant engineer. The geology of the Mother Lode has been described by Adolph Knopf in Professional Paper 157 of the United States Geological Survey; references to general geology have been abstracted largely from Knopf.

Jan 1, 1937