Search Documents

By Michael W. Redifer

A Fortran IV computer program was developed to calculate the composition at equilibrium of products from a set of high-temperature gas combustion reactions. The program was used to develop high-temperature equilibrium concentration profiles for various constituents as a function of temperature and oxygen concentration. The computer program was specifically applied to reactions pertaining to the corrosion of superheater tubes in pulverized coal-fired boilers; however, it is useful for any multicomponent, multireaction scheme in which equilibrium constant data can be obtained and is comprised of gaseous reactants along with finely dispersed solids or liquids. General applicability of the computer program, including its limitations, are discussed along with detailed instructions for using the program.

Jan 1, 1973

By Mark R. Pettitt

Noise surveys conducted in underground coal mines have consistently indicated that auger mining machines subject the operator and helpers to excessive noise exposure. The machine cutting heads have been identified as the primary noise source. This report documents the research program conducted to (1) investigate the nature of the cutting head noise problem, (2) develop noise control concepts, (3) devise in-mine survivable techniques to implement the noise control concepts, and (4) build and demonstrate prototype reduced-noise auger miner cutting heads. The dynamic forces generated during coal cutting by the brittle fracture of coal are predominently low frequency. The low-frequency (less than 1500 Hz) structural response of the cutting head, therefore, determines the noise radiated by the cutting head. The most feasible methods of reducing the cutting head low-frequency response are to increase both the structural stiffness and the low-frequency damping. A technique was devised to achieve these goals. The standard plate helix was replaced by a sand-filled hollow helix of triangular cross section, and the core diameter was increased with an attendant reduction in helix depth. Extended in-mine tests demonstrated the operational capability of the reduced-noise auger cutting heads. The simple noise control concepts are valid for all continuous miner cutting heads. The sand-filled hollow helix technique, which achieved a 10 dB(A) noise reduction for the auger, can be used on any helix-bearing Cutting head.

Jan 1, 1983

By Lloyd A. Morley

This annual report details progress under USBM Grant G0155003 during the project period of January 1, 1977 through December 31, 1977. The report contains four principal chapters covering accomplishments in the mine electrical safety research areas of continuous monitoring, battery and battery-charging safety, and computer modeling. Highlights of the work are summarized in the last report chapter.

Jan 1, 1978

By H. S. Auvil, L. D. Schmidt, H. G. Graham

"Several studies on the bulk density of coals prepared for byproduct-oven use were undertaken during the war by the Bureau of lanes in cooperation with the Office of the Solid Fuels Administrator and with the advice of the Coke Production Committee. The primary purpose of these studies was either to produce more uniform coke or to increase the throughput of existing facilities or both; the goal was increased Production of steel for war. As these studies were made, detailed reports were sent to the individual companies with whom the Bureau cooperated; also two reports,5/6/on the general subject of bulk-density control were published. In the course of the work, data were gathered that now prove of value in judging the merit of carious methods of testing bulk density and the limits of application of each method in byproduct-oven operations.Since the cessation of hostilities, the .Bureau section (Coke Production Survey Section) that conducted this work has been liquidated, but it was felt advisable to prepare a report on the accumulated experience so that it would be in a form available for the use of the industry and also as a base for any further research on the control of fluctuating bulk densities in coke ovens.It is hoped that the data and experiences recorded herein will be of material assistance to the many who have had difficulty in obtaining reproducible results in bulk-density testing. Since the data were gathered in the course of extending aid to individual plants in minimizing the deleterious effects of fluctuations in bulk density of oven charges on the quality and quantity of coke produced, certain desirable phases of an over-all investigation were not covered. However, on certain of these phases qualitative indications are available and the policy followed herein is that suggested by the American Society for Testing Materials Manual on Presentation of Data7/ that lacking quantitative information, relevant material should be included even though it ""may be qualitative in character, some may even be vague."""

May 1, 1946

By Robinson Newcomb

Gypsum is a form of hydrated calcium sulfate (CaS04.2H20) which is widely distributed over the earth's surface. The two varieties worked commercially are rock gypsum and incite. Rock gypsum, the variety commonly mined for commercial purposes, is a relatively soft mineral having a specific gravity of about 2.3 and weighing about 150 pounds per cubic foot. The chief producing States are New York, Michigan, and Iowa. Before being used the crude gypsum is ground and generally calcined. The predominant use of gypsum is for building purposes (the manufacture of plaster), for which calcined gypsum is required. Gypsum is also used as a retarder in Portland cement, as fertilizer, and for other purposes. GYPSUM MINING Crude gypsum is mined by two methods - underground and open-pit. Although the use of the former method predominates, open-pit mining increased in relative importance during the early twenties and contributed about two-fifths of the output during the period 1925-38.

Jan 1, 1940

By G. E. McElory

"INTRODUCTION The subject of mine and tunnel ventilation has two broad aspects - (1) what atmospheric conditions to obtain in underground openings and (2) how to maintain the desired conditions efficiently. The first relates primarily to quantity requirements of ventilating systems, whereas the second relates more particularly to pressure requirements. Both, therefore, determine power requirements, which is the deciding factor in any system of mine or tunnel ventilation.Both divisions of the subject have received considerable attention from the Bureau of Mines since its inception in 1910 in the form of research, service, and correlation and dissemination of information. Numerous papers on various Phases of the subject have been published, of which a selected list, numbered and arranged in chronological order by type of publication, will be found at the end of this Paper. One of these, Technical Paper 705 (25) 2/ gives a complete bibliography of Bureau of Mines publications dealing with health and safety. As indicated by the selected list of publications accompanying this paper, the health and safety aspects have received most of the attention devoted to this work, chiefly because these have been dominant factors in Bureau policy, but partly because these aspects lend themselves to laboratory research and small-scale field studies. Although considerable attention has also been devoted to the engineering aspects of mine and tunnel ventilation, there has been, in the opinion of the author, who has been engaged on this phase almost continuously for the last 30 years, only sporadic recognition of the vital effect this phase of the work could have on improving health and safety conditions. As a matter of fact, ventilation activities have constituted but a very minor part of the total work of the Bureau of Mines, as, except for a few years in the nineteen twenties, there have been only a few short intervals when more than two or three men were engaged in field work and a similar number in laboratory research directly related to mine gases or mine air."

Mar 1, 1950

By Arnold O. Tanner

The domestic mining industry gained more strength in 1988 as the healthy comeback that became evident in 1987 continued and grew for many commodities. The increasing and more stable commodity prices, still predominantly in the metals sector, reinforced both the new ways of conducting business and the use of technological advancements in successfully lowering operating costs during the last 4 to 6 years. Some commodities and companies still struggled to survive, but increases in productivity and profits were becoming more common.

Jan 1, 1990

By Joseph Gersic

The U.S. Bureau of Mines assessed mineral resources of the BLM Malheur-Jordan Resource Areas (MJRAs) in southeastern Oregon in 1993 and 1994. The study relied heavily on acquiring and analyzing existing data. In order to efficiently handle and analyze a large quantity of data, a minerals information management program, informally called MINFO, was developed as a frontend for three databases created to store basic information gathered during the minerals resource assessment. The MINFO program will also provide the BLM with a method of tracking and updating minerals information in the future because program modules in MINFO allow the addition of new data and the correction of errors, creation of print files, transfer of data to other database formats, exportation of data to other software packages, and creation of AutoCAD script files to be used in conjunction with AutoCAD to produce maps. The report specifically identifies significant past and present mineral exploration and development activities and possible areas of future mineral exploration and development. These areas are informally designated as areas of development interest or ADIs. The report contains a scenario of what mineral development might reasonably occur in the foreseeable future if the BLM does not substantially change its present resource management plan, and it shows the possible socioeconomic impacts of that development. The uncertainty of the political and economic situation makes it extremely challenging for the USBM to accurately predict a reasonably foreseeable development scenario. The reasonably foreseeable development (RFD) scenario developed by the USBM for the BLM indicates short-term RFD of minerals should have a negligible socioeconomic impact, and longer-term RFD of minerals should have a slight socioeconomic impact on the MJRAs. The mining industry is facing a rapidly changing business and regulatory environment in Oregon. Several signal changes have occurred recently, including State regulations that require significant bonding prior to the startup of "chemical process" mining, an initiative by a special interest group to stop all chemical process gold mining within the State, and an opinion by the Oregon Attorney General (AG) banning all forms of placer mining without exemption. In the AG opinion, not even gold panning is allowed, and the prohibition applies to mining claims on Federal lands. The State legislature may amend the statute to allow small scale placer mining to occur, as was allowed under an AG opinion issued in 1982. These and other changes occurring at the local, State, and National levels are making it more challenging for the mining industry to operate in the United States. Several epithermal gold properties in the MJRAs attracted the mining industry's interest. Only the Grassy Mountain Project of Newmont Grassy Mountain Corporation may be developed in the next few years. It is probable that at least two other properties will be developed if Grassy Mountain is successful. Mining companies are waiting to see the effect recently promulgated State mining regulations and more stringent proposed regulations, particularly bonding regulations, may have on Grassy Mountain. Resources of bentonite, diatomite, and zeolite are abundant. The almost Ubiquitous stone, sand and gravel, and semiprecious gemstone resources also were examined. Little environmental or socioeconomic impact is expected from reasonably foreseeable development of these mineral resources.

Jan 1, 1994

By John C. Machisak

INJURY DATA and experience at, coal mines in the United States for 1953 and 1954 are presented in this publication with a minimum of interpretation and comment because of the numerous tables required to afford detailed comparisons between the 2 years. Corresponding tables for 1953 and 1954 follow in consecutive order under the following general sections: (A) General injury experience: Tables 1 to 11: Contain current data on number of fatal and nonfatal injuries, frequency and severity rates, and average severity and time-loss rates. (B) Selected injury data: Tables 12 to 85: Contain current data on causes of injuries, distribution of injuries by part of body injured, days of disability, extent of hand and machine loading, experience by employment and production groups, and various other operating factors and physical conditions related to the occurrence of injuries at the Nation's coal mines.

Jan 1, 1958

By E. K. Stanek

This report contains the results of an investigation into the feasibility of periodically measuring parameters of the insulation for a mine electrical power system in order to detect incipient faults. The variety of insulation parameters evaluated included insulation resistance, dissipation factor, power factor (vs. applied voltage), current harmonics, leakage current, infrared radiation, as well as certain circuit breaker parameters and tests. In order to augment field tests a program of accelerated life testing was also carried out. Apparent inconsistencies in data were identified as the result of environmental effects, primarily temperature and relative humidity. A series of environmental tests were conducted to develop correction factors that allow one to refer measured parameters to standard conditions. A portable data collector was develop-ed to aid in the accurate collection and analysis of laboratory and field data. The primary conclusion is that insulation deterioration can be measured and failure predicted with reasonable confidence. The secondary conclusion is that most of the tests are impractical in the field although useful in the laboratory. Infrared sensing, insulation resistance and dissipation factor are the best insulation field tests when portability is taken into account.

Jan 1, 1979

By F. H. Gunnell, W. C. Dunham

"INTRODUCTION The Treasure Hill mines, situated in Dry Canyon, Ophir mining district, Tooele County, Utah, together with several other properties in the district, examined were examined by Frank L. Wideman, an engineer, the Bureau of Mines, in September 1942.In April 1945, development drilling was started on the Treasure Hill mines, which are operated under lease from the Madison Mines Co. The project was continued in 1946 and terminated in 1947.While the Bureau of Mines project was in progress, the Morgan and Fullion tunnel workings were surveyed by Bureau engineers.ACKNOWKEDGEMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy, It is the policy of the Bureau to publish the facts developed by each project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual investigative perk, and prepares the final report. The Branch, O. C. Ralston, chief, analyzes samples and performs beneficiation tests. The work here described was under the direct supervision of Paul T. Allsman, chief, Salt Lake City Division, Mining Branch."

Jan 1, 1948

A general description of investigative work conducted by the Bureau of Mines at the, Missouri Valley. manganese deposits and leading to tonnage and grade estimates has been given in Report of Investigations 4375, part 1 of a three-part report of work done between July 1945 and August 1947. Basic factual information from which tonnage and grade estimates were drawn was derived through the drilling sampling of 238 large-diameter bucket-drill holes in 11 widely separated areas. Drilling areas were selected after careful reconnaissance, mapping, and consideration of earlier work done on the deposits by the Bureau of Mines, State agencies, and private organizations and individuals. Stratigraphic studies permitted extending the results compiled within the drilling; areas to outcrop and lightly covered manganiferous zones between an beyond drilling areas. The locations of drilling areas, drilling sections, and individual drill hues are shown on illustrations in part 1 f this report. The individual drill holes, aside from providing the basic information for tonnage and grade estimates, disclosed features affecting any future plan As exploitation. It in particularly significant that a large part of the visible outcrops is faulted end otherwise complicated by slides that give a false impression of the thickness, vertical location, and even the existence of manganese-bearing zones.

Jan 1, 1949

By William J. Wuest

The technical analysis of parameters that can influence roof and rib reinforcement is important to the operation of safe and profitable underground mines. One such parameter, studied in this U.S. Bureau of Mines investigation, is the effect of time on untensioned, resin-grouted bolt anchorage characteristics. A group of seventy-three 4-ft-long bolts with three different grout column lengths were I installed in a stable coal mine roof. The bolts were then subjected to standardized pull tests at various intervals throughout a 37-month period. For each test, load-deformation data were reduced to determine axial stiffness and yield point. The magnitudes of these two anchorage characteristics at the time of installation were compared with results from subsequent pull tests to determine if anchorage capacity deteriorated. Bolts with 18-in grout columns were studied over 9 months, and no measurable loss occurred. Bolts with 48-and 24-in grout columns were studied over 37 months and also exhibited no measurable loss.

Jan 1, 2010

By H. P. Hermance

Preliminary examinations of the Parker and Webb deposits were made by E. E. Maillott, Bureau of Mines engineer in July 1942. The chemical and spectrographic analyses included in this report wore made at the Eastern Experiment Station of the Bureau of Mines at College Park, Md., under the general supervision successively of S. M. Shelton and of Paul M. Tyler, formerly regional engineer, Eastern Region. Beneficiation tests were conducted under the supervision of Frank D. Lamb. The mineral exploration was under the general supervision of J. D. Bardill, formerly district engineer. Acknowledgment is gratefully made to the St. Joseph Lead Co., in particular to John S. Brown and P. J. Mechin for their assistance. Special acknowledgment is made to the American Metal Co., Ltd., ,Ind to T. C. Moore for furnishing core-drill and assay data; to the Universal Exploration Co. and P. B. Jennings; and to the Northern New York Mining Corp. and C. H. Sprague for their permission to publish the core-drill dta. Excellent cooperation was given by Dr. W; M. Agar and C, L. Rogers of the Geological Survey.

Jan 1, 1949

By Neal M. Miur

"INTRODUCTION The Mineral Ridge-Clay Lick fault system in Crittenden and Livingston Counties, Kentucky, is one of the larger and more important fault systems of the Western Kentucky Fluorspar district. Total production from it up to July 1945 (chiefly since 1900) was approximately 80,000 tons of fluorspar ore, 10,000 tons of which came from the Mineral Ridge Fluorspar Co. tract 1, which was being operated by the Mahoning Mining Co. of Rosiclare, Ill. The fluorspar ore carries lead and zinc that can be recovered by milling, and the Mahoning Co. planned to log-wash the ore at the mine and then mill it in its mill at Rosiclare, The Mineral Ridge Fluorspar Co. properties were examined by O. M. Bishop, an engineer of the, Bureau of Mines, in August 1942. During 1943 and 1314, developments on the properties were under observation by X. B. Starnes, of the Bureau, and it was decided to diamond-drill tracts 1 and 2, as indications seemed favorable for opening up additional fluorspar ore bodies. Drilling was begun March 12, 1945, and was completed July 2, 1945, during which time 12 holed were drilled on tract 1 of the Mahoning Co.'s leases for a total of 3,637.1 feet, and one hole 359 feet deep was drilled on tract 2 of the Jennings lease. The Mineral Ridge-Clay Lick fault system, 4 to 47 feet wide, was encountered in all holes at 126 to 265 feet."

Apr 1, 1947

By Kenneth Maas

The Bureau of Mines devoted portions of the 1987-1988 field seasons to investigate the mineral aggregate industry in Juneau, Skagway, Haines, and Gustavus, Alaska, as part of the Juneau Mining District study. Statistics compiled for current suppliers include location, activity, reserve estimates, expected mine life, and types of commodities available. Each population center, except for Gustavus, is well endowed with suitable mineral aggregate to last at least 20 years. The Bureau of Mines quantified the mineral aggregate resource in many large potential sites within each area. Sampling, engineering and soil-index testing, site descriptions, deposit dimensions, and gold recovery information is described. Refraction seismic studies performed at three localities revealed gravel thicknesses in excess of 40 to 80 feet. In the Juneau area the Herbert/Eagle Rivers outwash area, East Fork Lace River. Antler/Gilkey Rivers, and Grizzly Bar (Taku Inlet) individually contain in excess of 60 million yd3 of excellent-quality aggregate with minor accessory gold credits. Haines is also well endowed with aggregate resources; large, quality deposits occur along and at the confluences of the Chilkat, Katzehin, Klehini, Tsirku, and Kicking Horse Rivers. Large deposits of granitic aggregate exist in the Skagway River and East Fork Skagway River.

Jan 1, 2012

By Oliver Bowles

"General.The term mica is probably derived from the Latin ""micare"", meaning to shine or glitter, for the brilliant reflection from mica flakes in rocks has directed more than ordinary attention to this group of minerals. Mica includes a group of several minerals all characterized by a perfect basal cleavage, by virtue of which they may be split into exceedingly thin plates. The minerals are of very common occurrence in all countries, constituting about 4 per cent of the igneous rocks of the world The term ""isinglass"" is sometimes applied to glazing mica, but this is incorrect, for true isinglass is a soluble combustible material made from the air bladders of certain fish. As a constituent of granites and schists, mica is present as flakes too small for commercial use. Mica occurs also as small scales in many sandstones. When granites decompose, the quartz and the white mica are the most resistant to weathering, and so remain when the other constituents have been decomposed and carried away. A secondary white mica known as sericite is formed by the metamorphosis of clay-bearing rocks, and thus, in extremely fine-grained form it constitutes an important constituent of slates and related rocks. Some schists contain a high percentage of mica, but the presence of large amounts of quartz and other minerals has up to the present time rendered them useless as commercial sources of mica for grinding. It is possible, however, that certain mica or seri-cite schists which are composed almost wholly of mica with very little quartz may be utilized for ground mica if found in large enough entity. Considerable micais sometimes found mixed with the residual kaolin that results from decomposition of pegmatites, and in one locality at least it has been recovered as a by-product in a clay purification plant."

May 1, 1922

By S. H. Ash

The Pennsylvania anthracite-mining region is the only one in the world of major magnitude. As the deposits of anthracite in the United States are limited virt113.lly to Pennsylvania, the difficulties of this industry have been commonly considered a State rather than a national problem. However, there is also national interest in the conservation and wise utilization of all fuel resources and in the control of interstate waterways. The anthracite industry is confronted with the very se:;-ious :problem of accumu.lation of water in many of the mines. This problem must be solved soon if progressively higr-er mi~ing costs are to be avoided. The water proble~ cannot be solved by the operating compa,nies without State or Federal aid, or both, owing to the magnitude of the work requir~d, diversity of interests of the coal ana surfa.ce ovmerships, hazard to the whole mining community, and interests affec~ed outside the mining region. The cost of abati~ the ever-increasing_surface seepage to mine workings and of handling this seepage once it }3s occurred is beyond the economic resources of most ope~ating ma.'18.gements. The data in this paper giving the high lights of the water problem and indicating what appears to be a step in the right direction are based upon observations made during the past year that the industry desires and believes it is to the npublic interesttr to keep mine workings free of flood end surface waters.

May 1, 1941

By Jack L. Henry

A laboratory and a pilot-plant-scale investigation has been conducted by the Bureau of Mines to examine possible sources of nitride defects in the production of magnesium-reduced titanium sponge. The production of alpha-stabilized nitride inclusions in hot-rolled titanium plate from air contamination of sponge during its manufacture has been experimentally demonstrated. Magnesium-reduced sponge prepared from air-contaminated magnesium or when contaminated by an air leak during reduction, vacuum distillation, or inert gas sweep, shows very large variations in nitrogen content. Refractory nitrides, delta TiN and epsilon Ti2N have been identified in this sponge. The highest incidence of inclusions resulted from sponge that was reduced by air-contaminated magnesium and from sponge subjected to air contamination during the vacuum distillation cycle and during helium sweep. Air contamination of sponge during the reduction cycle was not nearly as effective in producing inclusions. Tests showed that color and texture may not be reliable criteria for locating defects during sponge inspection. Maintenance of good vacuum-tight integrity, filtration of molten magnesium prior to charging into the reduction retort, and mechanical attrition of sponge to pulverize and disperse nitrides are suggested as practices to lower inclusion incidence in commercial titanium ingots.

Jan 1, 1974

By George Saliba

This report disucsses the formulation of a mathematical model for the steering of a conveyor belt by a flat return idler and a troughed idler under various loading conditions. Significant parameters associated with belt training are identified. The generation of a skewed flat return idler model in terms of a steering force and self-aligning torque is presented. Development of the mathematical model for the flat return steering idler is illustrated for the case of no circumferential slip occurring and for the assumption of a bidirectional slip mechanism. Experimental results supporting the theoretical analysis is presented.

Jan 1, 1977