Search Documents

By D. Harrington

As no cure is known for silicocis after it has developed, prevention is the only effective remedy. There are two main lines of approach to the problem of dust-disease prevention in industry - the engineering, through control of dust production, and the medical, through selection of workers by examination; success probably depends upon a combination of the two. Hatch (146) considers the following measures essential to a complete, well-balanced program of control of the dust hazard in industry: 1. Selection of workers by means of physical examinations in order especially to eliminate those with tuberculosis and other disorders of the respiratory system. 2. Reduction of the duct concentration below the standard of permissible dustiness through adequate moans of dust control and good housekeeping. 3. Limiting the frequency and duration of employment in the dusty occupations, thus reducing the rate of deposition of dust in the lungs. 4. Routine measurement of the effectiveness of the dust-control program by means of periodic medical examinations and duct surveys.

Jan 1, 1935

By David C. Grant

A laboratory technique for simulating in-situ uranium mining was developed and used to determine the effects of leaching variables on permeability, uranium recovery, leach solution interaction with the ore-aquifer environment, and post-leach chemical leakage. In particular, ammonium bicarbonate, the commonly-used leach solution, was examined in great detail. Agitation leach tests were conducted to examine the effect on ammonium sorption and desorption of clay content, solution and clay ammonium levels, pH, and the type and concentration of other anions and cations in solution. Initial column tests were performed to determine the degree of ore-aquifer interaction that could be expected for various leach solutions; sulfuric acid, and ammonium, sodium, and potassium bi-carbonates. Subsequent tests examined various methods to restore the ores by lowering the post-leach chemical leakage. The restoration tests examined the use of reducing agents (e.g., ammonium bisulfite, sodium bisulfite; and sodium sulfite), ore blocking and stabilizing agents (e.g., sodium silicate, aluminum chloride, and magnesium-calcium salt).and ammonium displacement agents (e.g., aluminum chloride and lanthanum chloride-sulfate)

Jan 1, 1980

By L. Nahai

Overall mineral industry productive activity in Europe increased in 1965, following general upward trends in gross national product and total industrial production4 recorded. The gross national product of non-Communist Europe in market prices in 1965 was estimated at $572 billion and that of Communist Europe at $409 billion. However, the extractive sectors of the mineral industries generally did not fare as well as the processing sectors. In fact, a number of countries recorded lower production levels in this sector in 1965 than in 1964 and most countries had a lower growth rate in extractive industry output than in overall industrial output. Among the non-Communist nations of Europe, a general decline in coal production and lower levels of iron ore output in France, West Germany, and Luxembourg contributed significantly to the smaller growth rates or declines in extractive indexes. Where higher indexes were registered, this generally resulted from the performance of the petroleum and natural gas industry; exceptions were Greece, Norway, and Sweden. The decline recorded for Czechoslovakia was attributable entirely to poorer performance by that nation's coal industry.

Jan 1, 1967

By J. C. Gerdeen

A new analytical model for the shear stiffness at a joint of the fully-grouted resin roofbolt is developed using the Theory of Elasticity and an analogy to a beam on an elastic foundation, Gerdeen [2]. The model developed in this study treats the elastic foundation modulus of the resin as being composed of both an elastic rock and an elastic resin. All previous attempts have neglected the elasticity of the rock and treated only the resin. A three dimensional finite element model of the bolt-resin-rock system is developed also and comparisons are made between the predictions made by it and the analytical solution. It is found that the agreement between the two representations ranges between 1.2% and 10.5%, with the greater differences being observed for systems of very large or very small bolt diameters and resin annulus thicknesses. Since such configurations are not the rule in practice parameter studies are performed using the analytical solution with the finite element solution being used as a check. For a 0.75 in. bolt, a resin annulus thickness of 0.1375 in., a resin with E = 7 x 105 psi and -1) = 0.210, and a rock of modulus E = 6.8 x 106 psi and V = 0.159 the shear stiffness is found to be 1.220 x 106 lb,/in, from the analytical solution and 1.245 x 106 lb,/in, from the finite element model. Applying the finite element model to the problem of the axial stiffness of the fully-grouted resin roofbolt a value of 6.002 x 106 lb./in. is obtained which proves to be at least 50% higher than any of the now existing analytical predictions.

Jan 1, 1976

By John E. Trombly

System objectives and design criteria for an in-mine visual personnel paging system are discussed. Display technologies are evaluated and tradeoffs leading to display selection are described. The prototype dispatcher's console, battery/receiver box and visual display assemblies are functionally described. The report includes circuit descriptions, schematics, parts lists and equipment cabinet drawings for the three assemblies. The report concludes with an estimate of the manufacturing cost for each assembly.

Jan 1, 1975

By Walter E. Lewis

The Fort Randall Reservoir project, on the Missouri River at Pickstown, S. Dak., was designed by the Corps of Engineers and is part of the Missouri River Basin Development Program. The location of the project with respect to adjacent features is shown' in figure 1. When the project is finished, it will include a large earthwork dam and 12 circular tunnels, 8 of which will be equipped for power and 4 for flood control. Various phases of the construction have been contracted to independent companies, and at present four companies are working on different phases of the project under a rigid time schedule. Western Contracting Corp. is the contractor on stage II, earthwork; Johnson-Winston Construction Co. is the contractor for construction of the intake towers at the upstream side of the dam; McCarthy Improvement Co. has the contract for the power house and the outlet works on the downstream side; and Silas Mason Co. has the contract for driving the power and flood-control tunnels. The latter two companies use the same roads for ingress and egress to their respective work areas and the same general waste dump area. Under such circumstances, it is necessary that each company stay on a time schedule in regular sequence to avoid interference with the other.

Jan 1, 1951

By R. L. Marek

The number of persons fatally injured in the California petroleum industry in 1932 was 24, a decrease of 6, or 20 percent from the number killed in 1931. The decrease in the number of fatalities occurring in 1932 caused the fatality curve of the California petroleum industry to reach its lowest point in 10 years. Changing conditions in the oil industry - reduced personnel, decreased active field development, and curtailed production - have undoubtedly caused a part of this decrease, but continued accident-prevention efforts by the industry have also contributed to the reduction in the number of fatalities for 1932. The Bureau of Mines has analyzed and reported annually the fatalities in the California petroleum industry for a period of 10 years. Figure 1 shows the trend of fatal accidents during that period. Fatality statistics for 1932 show that the drilling and producing, pipe line and transportation, and refining and natural gasoline divisions of the industry had fewer accidents in 1932 than in 1931, sales and marketing being the only division that showed an increase over 1931. The number of fatalities by divisions for 1931 and 1932, percent of total, and percentages of increase and decrease are given in Table 1.

Jan 1, 1933

By Lars G. Olavson

A prototype roof bolt which can be remotely placed by pumping has been developed by the Bureau of Mines. It is known as the "Pumpable Bolt". With the objective of field testing the effectiveness of the pumpable Bolt roof support system a mining machine was developed capable of installing Pumpable Bolts in the normal production cycle of a typical underground coal mine. The machine was built and the pumpable Bolt concept tested and evaluated as a total system in shop and mine tests. The machine was operated in the mining cycle of two mines and pumpable Bolts were installed at both mine sites.

Jan 1, 1976

By Lloyd A. Morley

This Bureau of Mines publication presents a comprehensive review of mine electrical power-system theory and practice. It discusses fundamental theory and the vital aspects to be considered in planning and designing mine electrical power systems. The report is divided into three major sections. The first presents the history of electricity in mining and the fundamentals of electrical phenomena and components. The second focuses on power-system components: motors, grounding systems, cables, and protective equipment and devices. The final section includes mine power-center equipment, switchhouses and substations, batteries, and mine maintenance.

Jan 1, 2003

"The mission of the Respirable Dust Center is to enhance the health, safety and productivity of the miners 'through advancing the fundamental .understanding of all aspects of respirable dust associated with mining and milling and the interaction of dus.t and lungs for reducing the incidence and severity of respirable dust disease. All Dust Center activities are focussed to be responsive to this mission which is shared by several federal agencies closely associated with the Generic Mineral Technology Center for Respirable Dust such as USBM, M,SHA, and NIOSH, and the mining industry. While significant progress has been achieved in making mine atmospheres cleaner and healthier, respirable dust disease remains the nations worst industrial hazard. GOALSThe goals of the Respirable Dust Center have been formulated to recognize the diverse scientific, engineering and medical aspects of respirable dust as well as the need to enhance the interaction, education and technology transfer in the respirable dust area.The Center goals are to:1. Enhance the understanding of the scientific, engineering and biological characteristics of fine and respirable mineral particles, fibers, organic aerosols, and complex particles found in the mining and milling atmospheres.2. Advance the understanding of the physical behavior of airborne respirable dust particles in flowing streams under different. stimuli during mining and milling.3. Advance fundamental understanding of the causative mechanisms for the occupationally related lung impairments and the airway diseases of mine and mill workers.4. Establish the relationship between natural and cultural factors (mine geology, mineralogy, mining and milling methods, equipment and control measures) in the generation, exposures, and pathogenic properties of fine particles.5. Contribute to the development of control mechanisms for reducing ambient respirable dust concentrations, worker exposure, the incidence and severity of dust related lung disorders and disease prevention in mining and milling atmospheres.6. Enhance functional integration among the various research personnel in the Center, as well as, with other groups, such as MSHA, NIOSH and USBM involved in respirable dust research and control.7. Develop technically trained personnel for employment in the mineral industry for respirable dust research and control.8. Enhance the availability of respirable dust-related information utilizing several technology transfer avenues."

Jan 1, 1990

By F. B. Petermann

The Bureau of Mines conducted electric furnace smelting tests on sintered flotation concentrate and siliceous log-washed are. The flotation concentrate was derived from the Maggie Canyon deposit of the Artillery Mountains area, Mohave County, Ariz., and contained, before sintering, 35.6 percent Mil and 19.4 percent Si02 + A1203. The log-washed ore was from the McGregor deposit of the Artillery Mountains area, Mohave County, Ariz., and contained 31.2 to 33.6 percent Mil, 19.5 to 27.6 percent Si02 + A1203, and 2.5 percent Pb. This work was undertaken to determine the most effective smelting technique for producing standard products from such nonspecification ore and concentrates. The objective was to collect data, using a small furnace, which would be reasonably accurate and permit extrapolation to large-scale practice for comparing with results on specification-grade are.

Jan 1, 1962

By Danny A. Riley, James R. Sanger, Hani S. Matloub, Michael Agresti, David Rowe, Lin-Ling Zhang, Yuhui Yan, Paula Galaviz, Judith Marchant-Hanson, Ji-Geng Yan

Until now there has been controversy about which tests should be performed to diagnose early Hand-Arm Vibration Syndrome (HAVS). Initial screening questions, especially about tingling and numbness, routinely given to patients prior to examinations proved to be a very important tool in the diagnostic process1, 4. However, standardized tests that are simple, quick, valid and reliable are needed to support a diagnosis of HAVS. Purpose: To find the most valid and reliable tests to diagnose HAVS. Material and Methods Five major tests were performed on Group I and Group II. Group I: Control group of 12 volunteers including students, nurses, secretaries and physicians with no history of using vibrating tools (age 20 to 50y, mean age 38.5y; 5male, 5 female.) Group II: 12 workers (age 17 to 65y, mean age 39y; 9 male, 3 female) were sent by a local trade union with a history of using vibrating power tools on their jobs for varying amounts of time (mean 12.2y, from 0.5 to 35y.) Pre-enrollment survey showed that each had more than 4 complaints commonly associated with use of vibrating tools (including numbness, tingling, weakness, pain, finger color or nail changes, temperature change, and difficulty moving.) 1. Sensory nerve conductive tests: Amplitude and nerve conductive velocity (NCV) were evaluated. 2. Cold Stress-Temperature recovery time tests were done on the index finger of the dominant hand following these steps: Confirm water bath is within 4-5º C. Place the finger temperature probe on pad of the index finger of the dominant hand. Record temperature every 15 seconds. Place subject’s hand in the cold- water bath for exactly five minutes. Record temperature every 15 seconds for ten minutes. 3. Blood test: Venous blood was taken by a 21-gauge needle with the yellow collection tube adapter. S-ICAM, Sera Thrombomodulin, Norepinephrine levels were evaluated by Henderson Research Centre, Canada. 4. Finger Sensory Evaluation: Semmes-Weinstein monofilament test and 2-point discrimination tests were performed on bilateral fingers. 5. Digital blood pressure test: blood pressure was measured in bilateral index fingers. Results 1. Median nerve sensory conductive amplitude from palm to wrist : GI: mean 96 ± 31µm; GII: mean 43± 30µm; for dominant hands. GI vs GII: P<0.001

Jan 6, 2006

By Thomas C. Denton

In 1965 Africa maintained its position as a region of the world essential to advanced non-Communist nations for supply of vital metals and minerals. The position stemmed from the fact that Africa produced in large quantity a number of key minerals of which either or both resources and production capacity elsewhere did not approach the needs of the free world. The Republic of South Africa alone contributed more than three quarters of the gold mined in the entire non-Communist world besides an estimated 60 percent of metals of the platinum group and the entire new supply of amosite asbestos, and Africa as a whole was nearly the non-Communist world&apos;s only source of gem and industrial diamond. Africa also accounted for 83 percent of non-Communist world cobalt production. Besides these massive contributions, Africa in 1965 provided 50 percent or more of the new supply from non-Communist countries of the following mineral commodities: Lithium minerals, corundum, manganese ore: and chromite, and over 20 percent of new supply from non-Communist countries of columbium-tantalum concentrates, antimony, beryl, vanadium, phosphate rock, and copper. Africa also accounted for 18 percent of the non-Communist world&apos;s output of uranium, 14 percent of its tin, 11 percent of its lead, 9 percent of its zinc, and 8.9 percent of its crude oil output. With respect to chromite, at yearend Africa&apos;s reserves of the mineral were far larger than those of all other non-Communist regions combined. This probably also held true for manganese ore. In the case of crude oil, the fact that Africa&apos;s share of non-Communist world output was 1.6 percentage points greater than in 1964 was significant, particularly inasmuch as the output rate was continuing to increase at yearend.

Jan 1, 1967

By Magnus Persson

ISO8662-4, “Hand-held portable power tools - Measurement of vibrations at the handle - Part 4: Grinders” is under revision. The new revision shall harmonize ISO 20643 “Mechanical vibration - Hand-held and hand-guided machinery - Principles for evaluation of vibration emission” which, among others, requires measurements in three directions and declared values related to the upper quartile of real-use vibration. To get the most suitable test method, a round robin test was made for evaluation of the two test methods proposed by the ad-hoc group working with this standard revision. Methods Seven laboratories measured the vibration from four grinders of different sizes, with and without autobalancing units. The laboratories come from universities, health & safety laboratories and grinder manufacturers. Two measurement methods are evaluated with respect to repeatability and reproducibility: 1. Grinding on a well-defined mild steel bar with depressed center wheels according to detailed test instructions. The test sequence starts and ends with 10 seconds of running the grinder in the air, when measuring the unbalance contribution to the vibration coming from the unbalance of the grinding wheel. Between these runs the average vibration during 60 seconds of grinding is measured. Three operators do five grinding tests per grinder. 2. Measurements using an aluminum unbalance disc similar to the one defined in ISO8662-4. Each operator runs the grinder four times, between each run the unbalance is moved 180 degrees to avoid variations caused by the play between the test wheel and the spindle. The averaging time is 10 seconds. Each grinder is tested by three operators. Repeatability is the spread within a lab between operators and over short time period for one machine and reproducibility is the spread between laboratories and over longer time periods for one machine. Instrumentation and transducer location are chosen according to ISO8662-4 and circulated test instructions. Results Both the repeatability and reproducibility is poor for the real grinding test, see figure 1. The coefficient of variation for repeatability is approximately 40% higher for the grinding test and the coefficient of reproducibility is 60% higher for the grinding test than for the unbalance disc test.

Jan 6, 2006

By E. D. Calvert

The Bureau of Mines, in its effort to promote greater utilization of domestically abundant materials, conducted reasearch on an alternate mold material that has commercial potential for titanium investment casting. Using variations of the conventional lost wax molding process, investment shell molds were formed entirely of fused, calcia-stabilized Zr02 and a Zr02-forming binder. Optimization of binder/slurry properties&apos;, stucco grain size and dis¬tribution, and curing practices resulted in a structurally sound investment shell that was distortion free and thermally stable. Small titanium castings, weighing up to 10 pounds, were prepared in unheated molds by both static and centrifugal casting techniques. Microstruc¬tural examination of the castings revealed that mold fill and surface quality were enhanced by centrifugal casting, although good results also were obtained from the statically poured molds. Microstructural and electron microprobe examinations showed that excessive, brittle case formation could be avoided by curing the dried shell molds in air for at least 2 hours at 1,400° C. Increasing curing temperature and time above these levels yielded added bene¬fits. Molds fired in vacuum at 1,500° C for 4 hours yielded castings essen¬tially free of case formation. The tensile properties of as-cast test specimens (no surface conditioning performed) id the chemical composition of representative metal samples showed that castings produced were comparable to Grades C-1 and C-2 unalloyed titanium This indicated that no sifnificant degradation of metal properties resulted from mold/metal interaction.

Jan 1, 1981

By O. H. Metzger

This is one of a series of capers being published by the Bureau of Mines on gold mining A the Western States. It describes the production of gold in the principal mining districts of New Mexico. The material was gathered red on a trip through tale State in the summer of 1936. ACKNOWLEDGMENTS The author acknowledges the aid and cooperation of mine operators in all parts of the State, who willingly contributed all information requested. Geological reports of the Geological Survey and the New. Mexico Bureau of Mince were drawn upon freely for information; credit to individual paper, is given in the text.

Jan 1, 1938

All of the coal resource in North Dakota is lignite. The lignite fields of North Dakota cover approximately 40 percent of the total area of the state, with reserves estimated to be 9.8 billion tons, two percent of the U.S. base. The first commercial coal mine in North Dakota opened in Morton County in 1873. As the railroads crossed the plains, the demand for coal increased. Coal for fuel was supplied by the state&apos;s underground mines. By 1884, North Dakota&apos;s lignite production had reached 35,000 tons. North Dakota was among the fist states to shift from underground to large-scale commercial surface coal mining. By 1927,40 percent of the total production was by surface mining, compared to 2 percent for the nation as a whole. By 1959,86 percent of the total production was by surface mining, while the national average was 22 percent. Since 1966, surface mining has been the exclusive coal production method in North Dakota. North Dakota&apos;s regulatory program received conditional approval December 15, 1980. Following approval of amendments to the program, it received full approval February 18, 1986. The Abandoned Mine Lands Program was approved December 23,1981.

Jan 1, 1992

By Iain Finnie

This report is in three parts. The first part presents a review of theoretical models which have been developed to study removal operations for various types of materials. In the second part, a brief summary is given of coal cutting research. The majority of this work has been carried out in Britain using chisel type bits rather than the conical picks which are in general use in this country. However, a comparison of specific energies measured for conical picks in the laboratory and in the mine shows very encouraging correspondence. In the third part of the report, analytical models for coal cutting by picks are suggested. An extension of the British "tensile breakage" theory, developed for chisels, is given for picks. The role of crushing and cutting in coal removal is discussed as a theory which combines the two processes is shown to give reasonable predictions for specific energy requirements. Finally, directions in which the existing theory could be improved are presented and the need for further research is emphasized.

Jan 1, 1977

Empirical methods involve the scientific interpretation of real-world experience. Many problems in ground control lend themselves to an empirical approach because the mines provide us with plenty of experience with full-scale rock structures. During the past 10 years, powerful design techniques have emerged from statistical analyses of large databases of real-world pillar successes and failures. These include the Analysis of Retreat Mining Pillar Stability (ARMPS), the Analysis of Longwall Pillar Stability (ALPS), the Mark-Bieniawski rectangular pillar strength formula, and guidelines for preventing massive pillar collapses. In the process, our practical understanding of pillar behavior has been greatly enriched.

Jan 5, 1999

By V. F. Parry

The object of this report is to present certain pertinent data on the physical and chemical properties of South Arcot lignite and to present the results of several special tests to show how the raw lignite can be upgraded to superior fuels for certain special uses. The Bureau of Mines Branch of Coal Technology laboratories at Denver have advocated the drying and carbonization of all low-rank fuels for special uses and have introduced and developed new techniques for upgrading and refining noncoking coals. Application of these techniques to the South Arcot lignites was the object of the investigation, and this report presents significant data necessary for planning a fuel program based on utilization of dried and carbonized dusts. In general, the South Arcot lignite is similar in chemical properties to the high-moisture lignites found in the United States and has some physical properties similar to Australian brown coals. The samples submitted for test had lost moisture before delivery to the laboratory, and it has been necessary to estimate the analysis of the lignite in place in the mine. Various observations made in India by qualified technicians indicate that the bed moisture content of the entire seam is in the range of 54 to 56 percent. For estimating purposes in this report, the bed moisture content has been taken as 56 percent and the ash content of the fresh coal as 2.5 percent. The average analysis estimated for the as-mined lignite is: [Moisture percent 56.0 Volatile matter do.22.0 Fixed carbon do.19.5 Ash do.2.5 Heating value B.t.u. per lb. 4,890]

Jan 1, 1957