Search Documents

By Louis Schaffer

The objectives of the research were to determine whether a model health and safety program could be defined in terms which would enable its application to mines of all types, and, if such a model program could be defined to determine through evaluations in two mining companies whether it would achieve measurable improvements. This volume describes the model, how it was applied in the field, and how it was evaluated. Anecdotal data to illustrate common kinds of safety problems and their solutions are included. The literature and field research that preceded the model definition is discussed in Vol. 2, which covers the period of September, 1980 to September, 1981.

Jan 1, 1983

By J. Douglas Causey

In 1984, at the request of the Bureau of Land Management, the Bureau of Mines studied 9,600 acres of the 12,350-acre Antelope Creek Wilderness Study Area (MT-065-266) in order to evaluate its mineral resources. Within this report, these 9,600 acres are referred to as the study area. The Antelope Creek Wilderness Study Area, Phillips County, MT, adjoins the north end of the Charles M. Russell Wildlife Refuge. Considered part of the Missouri River Breaks, the area straddles the edge of a thrust fault zone that has deformed the Mesozoic strata in the west half of the area. Shale, siltstone, and sandstone of Cretaceous Age are exposed in the area. Coal beds averaging 3.0 ft thick occur in the Judith River Formation. About 0.20 million short tons of coal were mined from the Judith River Formation adjacent to the west boundary of the area; no production is known in the study area.

Jan 1, 1986

By V. F. Parry

Subbituminous coal or lignite when stored in random riles or in ordinary bins in which the temperature fluctuates and air circulates quickly undergoes objectionable physical and chemical changes, which decrease the utilization value of the fuel and increase its tendency to ignite spontaneously. Slacking takes place, and the heating value decreases. Those changes are accelerated by fluctuations of temperature and by circulation of air through the storage space. When such coals are exposed to the weather they lose moisture rapidly. If evaporation from the surface of a lump proceeds at a faster rate than that at which it is replaced by moisture from the interior, the rate of shrinkage at the surface is greater than that at the interior; consequently stresses are generated at the surface which cause the coal to disintegrate. Likewise, when moisture is absorbed by the air-dried surface the outside layers expand at a faster rate than the interior, which results in further break-down. As these cycles are repeated the lump may disintegrate completely. Therefore, successful storage of low-rank coals depends on control of the factors that influence change of moisture.

Jan 1, 1941

By Michael Rieber

An analysis of coal slurry pipelines was presented in our May 1976 study, Route Specific Cost Comparisons: Unit Trains, Coal Slurry Pipelines and Extra High Voltage Transmission (4]. The present study extends that analysis. The earlier work included technical and economic cost descriptions of the black Mesa and ETSI pipelines as well as some hypothetical pipeline routes. Water problems, safety and environment, required resources, and labor impacts were discussed at some length. Additionally, pipeline impacts on competing railroads, slurry-rail comparisons, and cost escalation. were analyzed. The difference in pipeline profitability to an owner-operator versus a promoter-builder was suggested. These aspects are not redone in this study. Here, we present a synopsis of the previous results and a general statement of coal slurry pipelines. Extensions of the arguments are presented where they appear warranted. New material is developed in the area of pipeline branching and tapping. This would appear necessary if slurry pipelines are to function as more than private lines; if they are, for example, to be responsive to common carrier requirements.

Jan 1, 1977

By Victor R. Spironello

The Bureau of Mines has conducted studies of the slags related to ferrous technology to evaluate experimentally acceptable substitutes for the auxiliary flux, mineral fluorspar, in steelmaking operations. Comparative heats were made in a 1/4-ton, pilot-scale, basic oxygen furnace (BOF) to evaluate a waste material known as "used potlining." Used pot lining is recovered from alumina reduction cells after its useful life and contains significant levels of fluorine and sodium in various compounds. This material in both lump and pelletized form provided adequately fluid slags, based on observations made during BOF operation. No adverse effects were found on furnace performance, metal and slag chemsitry, the strength of the steel produced, or the environment. Fluorine recovery in the slag was about the same as that obtained when using fluorspar, as were the losses to the scrubber water and solids. No difference was observed in furnace-refractory attack, as determined by the level of magnesia in the slag. The sodium recovered in the slag apparently also contributed to fluidity, since the fluorine input was at about two-thirds that of the fluorspar. Used potlining was determined experimentally to be a satisfactory substitute for fluorspar in basic oxygen steelmaking.

Jan 1, 1982

By Richard E. Thill

Elastic wave velocities and moduli were determined by both the pulse and resonance methods in a large number of specimens of St. Cloud Gray Granodiorite and Tennessee marble under the same moisture, temperature, and stress environment. Long cylinders were first tested by the resonance method to obtain longitudinal bar and torsional wave velocity. The cylinders were then sectioned in half and tested by the pulse method to obtain the transient pulse velocity. These velocities were later used to obtain various moduli for comparison. Statistical comparisons between the Young's, shear, and bulk moduli and Poisson's ratios obtained independently by the pulse and resonance methods indicate that the methods do not give equivalent results in nearly isotropic rock. The amount of difference varies for each modulus, with the least difference (less than 5 pct) occurring in the shear modulus and the greatest difference (as high as 34 pct) in the bulk modulus. Moduli determinations in aluminum show much closer agreement between the pulse and resonance methods than in rock. The discrepancy in pulse and resonance results probably is caused by frequency dispersion effects and by differences in error sensitivity in the various formulas used to calculate the moduli.

Jan 1, 1974

By Michael C. Horn

The 61,470-acre Lick Creek Roadless Study Area is in the western Salmon River Mountains, centered 12 miles northeast from McCall, ID. U.S. Bureau of Mines personnel examined the roadless area in 1984. There is no recorded mineral production from the study area and no current mineral-related activity was observed. The roadless area is underlain by granitic rocks of the Idaho batholith. Pegmatite dikes and aplite dikes are present locally. Sampling indicates these rocks are not mineralized. No mineral resources were identified. INTRODUCTION This report describes the USBM (U.S. Bureau of Mines) portion of a cooperative study with the USGS (U.S. Geological Survey) to evaluate mineral resources and potential of federal lands recommended for wilderness, as required by The Wilderness Act of 1964. The USBM examines and evaluates individual mines, claims, prospects, and mineralized zones; USGS conducts broader geological, geochemical, and geophysical surveys. Such data helps Congress and other federal agencies make decisions affecting the use of public lands.

Jan 1, 1986

By Laurance L. Oden

The Bureau of Mines is developing nickel catalysts for converting synthesis gas derived from coal to synthetic natural gas. The present report describes the relationship between the composition of aluminum-nickel alloys in the composition range NiAl3 to Ni2Al3 equilibrated at 840° C and the properties of catalysts obtained from them. Methanation activity was determined in the temperature range of 300° to 360° C in a flowing gas stream containing 1 pct CO, 8 pct H2, and the remainder He. One part per million of H2S was added to the gas stream at 400° C to evaluate the susceptibility of catalysts to sulfur poisoning. The total surface area was measured by the adsorption of nitrogen at liquid nitrogen temperature, and the active surface area was measured by the adsorption of hydrogen at room temperature. Total surface area and active surface area were found to increase with increasing proportion of aluminum-saturated Ni2Al3 in the precursor alloy, but methanation activity and resistance to poisoning by H2S were nearly constant. However, the methanation activity of the catalyst prepared from stoichiometric Ni2Al3 was less than half that of the other catalysts.

Jan 1, 1978

By Richard B. Moore

This bulletin presents a summary of available information regarding the sources of uranium, radium, and vanadium, the methods used in treating the ores, and the uses of the finished products. In particular the paper describes the ores found in the United States, giving especial attention to those characteristics of the ores and the conditions of their occurrence that affect mining and treatment. ACKNOWLEDGMENTS. In the preparation of this bulletin a number of persons rendered assistance by furnishing information and by making it possible for us to visit the carnotite deposits in western Colorado and eastern Utah at a time of the year when without this assistance it would have been difficult to obtain satisfactory results. We desire to express our thanks to the following persons: Henry Hall, W. L. Cummings, T. V. Curran, K. D. Hequembourg, David Taylor, H. C. Brown, Forbes Rickard, George W. Alsdorf, Dr. Herman Fleck, Orr J. Adams, C. S. Cherrington, Newt. Stewart, O. B. Willmarth, Angus Cameron, George A. Head, and Lorimer Bros.

Jan 1, 1913

By H. M. Lawrence

"Florida, the State that supplied 82 per cent of the phosphate rock sold in the United. States in 19284, has two producing areas - the hard-rock and the land pebble districts. Production of the hard-rock field, decreasing importance in recent years, is now confined to mines near Dunnellon, in Marion and. Citrus Counties. The land-pebble district, with a production of almost 80 per coat of the nation's requirements, is located, in Polk and Hillsborough Counties. In the land-pebble area the phosphate deposits - probably Pliocene in age, derived by marine action from underlying, older, phosphate-bearing formations - consist of beds of phosphate matrix, covered by practically barren sands and clays. The overburden, ranging in thickness up to 45 feet, is removed by hydraulic methods or by drag-line excavators. The matrix, ordinarily less than 25 feet in thickness, is mined by hydraulicking and is pumped to adjacent washing plants for beneficiation. The dried product of the washing plants is the Florida pebble rock that is sold in foreign as well as domestic markets.The beneficiation of phosphate ores in the land-pebble district of Florida has been largely limited in the past to the recovery of the coarser pebbles. By washing and screening the crude matrix a separation is effected at about 20 mesh (0.033 inch). The coarser material is the phosphate-rock product of the plant and the finer material is discarded. The amenability of the washer- rejects to treatment by other processes is being investigated. Of methods that may have some application to the treatment of the low-grade phosphatic sands that comprise the greater portion of the washer-rejects, gravity concentration has received some study.Laboratory experiments to determine the amenability of phosphate sands to gravity methods of concentration were first performed in October, 1927. Later, in the winter of 1928-1929, a further series of teats was made,. In these later tests phosphatic sands were concentrated by hydraulic classification, and. also by hydraulic classification followed by tabling. In these experiments concentrates with an analysis above the minimum grade of commercial phosphate rock (66 per cent bone phosphate of lime - B.P.L.) obtained. The recovery of the phosphate varied but was promising enough to warrant further study. A more comprehensive investigation was therefore outlined. This paper presents the results obtained from an investigation, of classification and tabling of phosphatic sands recently completed by the United States Bureau of Mines Su cooperation with certain Florida phosphate companies, the Missouri School of Mines and Metallurgy, and the University of Alabama."

Jul 1, 1930

By Terry S. Cory

This report describes the results of a measurement program to determine the broad spectral characteristics of both differential and common mode noise on phone lines in three coal mines; and, signal attenuation spectral characteristics on the same broad basis over phone line strings with taps/branches. The frequency range used was baseband -1000 Hz for resolution bandwidth ranging from 100 Hz near baseband to 30 KHz near I MHz. The signal attenuation measurements were performed on all three "legs" of taps where possible and applicable. Results were obtained comparing shielded and unshielded phone lines In one mine. The results include an improved electromagnetic noise chart for coal mines showing variations with types of mines, topology, and location of noise sources; also, fundamental high-frequency limit on untreated phone lines in coal mines is identified

Jan 1, 1981

By Robert W. Van Dolah

On December 27, 1961, a fire and explosion destroyed the blasting agent mixing plant and an attached storage barn of the Whitaker-Atlas Supply Co., near Norton, Wise County, Va. Five residences, an office building, four trucks, and three automobiles were completely destroyed; a house trailer and several other trucks and automobiles were severely damaged; and other property damage, including much window breakage, occurred up to 3 miles or more airline distance away. Through the quick action of the fire marshal of the Norton Fire Department, Norton, Va., there were no fatalities and only five persons required hospitalization. This incident is of particular interest because of the widespread practice of mixing fuel oil (FO) with ammonium nitrate (AN) to prepare low-cost blasting agents, in many cases under conditions and circumstances not very different from those presented here. A representative of the Bureau of Mines Explosives Research Laboratory, Pittsburgh, Pa., and field representatives of the Bureau's Health and Safety Activities conducted the investigation. Information in this report was obtained from representatives of the Whitaker-Atlas Supply Co., the Norton fire marshal, and others who were on the scene either shortly before or after the incident occurred. Representatives of the Manufacturing Chemists' Association, the Institute of Makers of Explosives, and individual ammonium nitrate producers participated in the inquiries and investigations.

Jan 1, 1962

By J. Mitchell Linne

In 1985, at the request of Bureau of Land Management, the U.S. Bureau of Mines studied a 54,480-acre portion of the 93,205-acre Dry Valley Rim Wilderness Study Area (CA-020-615), in order to evaluate its identified resources. The area studied is in Washoe County, NV, and Lassen County, CA, about 35 miles east of Susanville, CA. No metallic resources were identified. The Red Rock and Willow Springs areas contain 85 million tons of altered basalt with zeolite amygdules. This material, averaging more than 50 percent chabazite, constitutes a subeconomic zeolite resource. This zeolite-bearing material would require beneficiation to upgrade it for higher value uses. Natural zeolites have a small market in the United States, which is presently supplied by other higher grade material. There is low probability that these resources will be mined in the foreseeable future. The Capricorn claims, adjacent to the study area, are on alluvial sediments containing more than 30 percent montmorillonoid clays. The material is not usable as pozzolan and was not tested for other uses such as absorbency, oil clarification, or insecticide carrier. The term pozzolan refers to a number of siliceous materials which are combined with portland cement to enhance the physical properties of the resultant concrete. The area is remote from market and contains low value material. It is improbable that this occurrence will be mined in the foreseeable future.

Jan 1, 1987

By M. R. Geer

Efforts to evaluate washery performance are nearly as old as the art of coal cleaning, and in former years there was no uniformity in either the methods used or the basic terminology employed. This situation, and the con- fusion it bred, prevailed until about the time of the First International Coal Preparation Conference in 1950, Largely because of the interest of the French coal research organization Cerchar, the subject of evaluating performance was given prime importance at this conference. As a result, there is now a much greater degree of uniformity in terminology and methods of expressing cleaning results. The International Standards Organization currently is working toward international standards of terminology and methods that should improve the situation even more. The various criteria that are used to evaluate the performance of coal- cleaning equipment fall into three categories, depending upon the extent to which they are dependent on the density composition of the raw coal; some are directly dependent, others are only indirectly dependent, and still others are substantially indenpendent.

Jan 1, 1962

By Mark P. Meyer

A mineral investigation of the Chugach National Forest, Alaska was conducted jointly by the U.S. Geological Survey and the U.S. Bureau of Mines from 1979 to 1983 as part of the RARE II program. The U. S. Geological Survey remapped the geology and distribution of mineral resources. The Bureau investigated mines, prospects, and mineral occurrences. Previously unreported mineralization in three areas, Long Bay, Wells Bay, and Miners River were discovered in the western portion of the SOUND study area. Copper, lead, zinc, gold, silver, nickel, cobalt, fluorite, and arsenic were found in north-northeast to north-northwest trending shear zones, veins, felsic dikes, and granitic intrusives in Tertiary Orca Group metasedimentary rocks.

Jan 1, 2011

By W. C. Babcock

This report covers Phase V of .a continuing program to apply a new liquid membrane process called coupled transport to the recovery pf metals from hydrometallurgical leach solutions. During this phase of the program, a membrane system of moderate scale was constructed and field-tested at the Exxon Highlands Mine and Mill Co. site near Douglas, Wyoming. The test unit contained four hollow-fiber membrane modules, each with 100 ft2 of membrane area. In the field tests, about 1000 gallons per day of leach solution was processed. The unit was operated on the leach solution for about 50 days. Leach solution entering the unit contained 100 ppm uranium. This concentration was reduced to about 5 ppm by coupled-transport treatment, and the uranium was concentrated to about 2 wt% as a uranyl carbonate product. Under these conditions, a transmembrane uranium flux of about 2.5 lb/ft2-year was obtained. An economic analysis showed that the cost of recovering uranium from this leach solution via coupled trans-port is about $1.20/lb. At higher concentrations of uranium in the leach solution this cost is reduced. For example, at 1000 ppm the cost of uranium recovery is about $0.30/lb.

Jan 1, 1983

By R. D. Joseph

This report deals exclusively with roof-fall accidents that occurred during 1955 and 1956 in both anthracite and bituminous-coal mines throughout the United States. The report stems from a cooperative study conducted by the Bureau of Mines and the Roof-Control Committee of the Coal-Mining Section, National Safety Council. The study includes an analysis of individual accident reports, sets forth the measurable factors, and compares such factors with a representative sample of average data from 39 anthracite mines and 117 bituminous mines (appendixes A and B). Particular emphasis is placed on fatal roof-fall accidents with respect to their causes, locations, and the methods of support used at the point of occurrence. INTRODUCTION The purpose of the report is to classify all measurable details of the occurrences of roof-fall fatalities so that the material presented will assist those promoting safety and will serve as a manual for those whose principal duty is inspection of mines.

Jan 1, 1958

By Thomas J. Peters

In 1985, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied a 17,320-acre portion of the 52,143-acre Little High Rock Canyon Wilderness Study Area (CA-020-913/NV-020-008) in order to evaluate its identified mineral resources. The study area is located in Humboldt and Washoe Counties, NV, about 42 miles north from Gerlach. Three areas of epithermal alteration, similar to alteration associated with disseminated gold deposits, were found in the study area. One of the areas occurs along a northeast-trending structural lineament. Southwest of the study area two gold prospects undergoing active exploration, as well JS a gold deposit being prepared for production, occur along the same lineament. The Bureau of Mines examination, however, did not find evidence for gold resources in the study area.

Jan 1, 1987

By Donald O. Capstick

The U.S. Bureau of Mines conducted an inventory of the prospects and mineral resources in the Scodies RARE II area (No. 5212) in 1982. No mineral production is recorded from the area, and no mines are being developed. The Scodies RARE II area is comprised primarily of light colored granodiorite with minor inclusions of mafic granitic rocks. Late stage differentiates of magmas resulted in quartz veins and pods. Metasedimentary rocks which have been mineralized in some parts of the Sierra Nevada were not observed within the study area during this investigation but small inclusions have been reported.

Jan 1, 1983

By Eldon Keith Stanek

This annual report deals with four distinct tasks related to research on the safety and reliability of mine electrical power systems. Task one is to develop tests and the associated instrumentation to detect incipient faults on a mine or any low-voltage power system. Task two is a dual effort related to the digital prediction of electrical transients on mine power systems and laboratory testing of transient suppression devices. Task three is also a dual effort. This task consists of both theoretical and laboratory work to assess both the reliability and the fail-safe characteristics of several items of protective equipment used in mine power systems. Task four consists of an effort to use programmable calculators and/or computer terminals to check overcurrent protective device coordination.

Jan 1, 1976