Search Documents

By Marcia Harris, Richard Mainiero

The New York State Department of Transportation recently commenced highway widening and drainage improvement projects in Clarence and Amherst, NY. Drainage improvements including the installation of storm sewer lines required excavation to a depth of 2.5 m (8.2 ft). In September 2002, NYSDOT stopped further blasting when 800 ppm CO was detected in the basement of a house near the blasting site. At the insistence of NYSDOT, the general contractor developed a new blast plan with the assistance of an environmental consultant. The plan provided for the installation of multi-gas monitors in buildings of special concern and/or with basements and residential type CO monitors in all other buildings within 100m (330 ft) of the blast. The multi-gas monitors would be remotely monitored. The plan provided action levels which would ensure public safety. The blast design was also modified to allow for better venting of CO. Blasts were limited to 20 ft lengths. The overburden was to be removed from the rock and blasting mats put in place to prevent flyrock. Approximately twenty feet of trench adjacent to the blast was left open to allow ground movement and gas release. The use of CO monitors was effective to alert occupants of a building to the presence of CO. The most effective appeared to be the residential type CO alarms with digital readouts. They were simple and easy to use and allowed the public to participate in the process. False alarms were repeatedly received with the more sophisticated instrumentation. Residential type CO monitors are preferable to warn people near blast sites. More sophisticated instrumentation should be avoided unless personnel are experienced in its use. A general overview of the blasting and monitoring is presented and discussed. The use and effectiveness of residential type CO monitors and multi-gas monitors are discussed.

Jan 1, 2004

By Hans-Peter Rossmanith

Fracture mechanics (Atkinson 1987, Broek 1988, Rossmanith 1978-2002, 1983, 1997, Kanninen & Popelar 1985) and wave propagation (Graf 1975, Rinehart 1975) form the main ingredients in the new electronic detonator based blasting technology. The full potential of using short delay initiation timing in bench and underground blasting can only be exploited if the underlying physical processes are properly understood. From a structural geology point of view, in many open pit mine operations, blasting is performed in incompetent and/or loose rock. Under such conditions the stress waves produced by blasting very quickly dissipate in the rock mass and often their energy cannot effectively be put to work. This contribution shows the effect of open and closed joints – and to some degree also faulting – on the blast wave field and shows the influence of structural geology on the blasting result. A simple engineering method which combines wave propagation and impact mechanics is developed in order to assist the non-scientifically trained blaster in understanding blasting in blocky rock formations. Extensive use will be made of the so-called Lagrange diagram which was introduced in detail in the author’s previous lecture at ISEE 2003 (Rossmanith 2003). This presentation can be considered a continuation of the 2003 presentation.

Jan 1, 2004

By P. R. Mohanty, Kaushik Dey

Blast-induced tunnel overbreak prediction in the past has been based on peak particle velocity measured far from the blast site with necessary extrapolation. This has often resulted in suggesting higher damage threshold levels of Acceleration/PPV for overbreak prediction (Bogdanhoff, 1995, Holmberg and Persson, 1997, Murthy and Dey, 2002). These, site-specific far-field blast vibration studies, have also revealed that predicted PPV levels for overbreak could lie in the range of 700-5000 mm/s, an extremely wide range to generalize. Experimental blasts were conducted, in an underground metal mine located in eastern India, with an objective to study the level of acceleration /peak particle velocity generated in tunnel blasting. Accelerometers and tri-axial geophones with measuring ranges upto 500 g, 254 mm/s respectively, were mounted on the tunnel floor close to the blast face, with sensor distances varying from 15.25m to 36.10m. Due to straight faces the measuring distance could not be reduced further anticipating, in particular, cable damage. The equipment used was of M/s Instantel Inc., Canada. The blast pattern used was burn cut with large dia relief holes providing the required free face. The blast hole depth was 1.8m. Tunnel overbreak was measured using a telescopic offset rod fabricated at Indian School of Mines, Dhanbad, India.

Jan 1, 2004

By L. Chaves

In rock blasting, due to numerous factors, both controllable and uncontrollable, the execution rarely meets the planning. The powder factor is an important KPI for blasting since it represents the amount of explosive used to fragment the rock, therefore it depends on the rock mass characteristics and may be influenced by factors such as weathering and drilling quality. The blasts at the Serra Sul mine, S11D project, are usually big blasts and the high productivity is a challenge for maintaining the quality of the whole drill and blast process. It is important to know the contributions of each of the most common influencing factors of the powder factor to direct the efforts to the improvement of the process. A buildup model is presented to evaluate the contributions of five influencing factors to evaluate the planed x executed powder factor. The factors considered in the model are the average hole depth, the amount of hole/blasted volume, the stemming and decking length, the linear charge weight, and the density of the explosive used. The build-up may be applied for both individual blasts and for overall view of the blasts in a period. A case study is presented with the application of the model for the monthly powder factor analysis at Serra Sul mine has contributed to direct efforts to enhance drilling quality and preservation of the drilled holes.

Jan 1, 2024

By Visitor Makiyi, Chris Batten

Poor coal recovery due to coal damage or loss caused by blasting can have a significant impact on a mining operation. Increasing coal recovery by reducing blast damage can provide a significant opportunity for coal mines to maximise their revenue and reduce their operating costs. This paper provides details on advanced drilling and blasting techniques used throughout the coal industry globally to prevent coal damage and movement during blasting. Typical coal loss and damage mechanisms are explained, along with how each of the applied techniques works to minimise the impact of each mechanism. Key requirements for a coal loss reduction program are detailed with typical design parameters used for each of the methods discussed. The positives and negatives of each method are also provided to enable comparisons and help determine suitability for a particular coal mining operation.

Jan 21, 2025

By Timothy D. Stark

Blasters are usually strictly liable for injury or damage caused by flyrock (trespassory invasion) and blast-induced vibrations (non-trespassory invasion). The application of strict liability to non-trespassory invasions has resulted in significant litigation that has hampered the use of blasting and the blasting industry. Stark (2002) proposes that blasters should not be held strictly liable for non-trespassory invasions but should be liable only if their conduct is proven to be negligent. This change in legal standard was proposed because improvements in blasting technology over the last thirty years allow blasting to be conducted without substantial risk of harm to property and thus the amount of harm imposed by a blast can be related to the level of care exercised by the blaster. It is anticipated that negligence standard will reduce the amount of litigation because a plaintiff will have a greater burden to overcome. To facilitate the acceptance of negligence standard by a court of law, this paper illustrates the application of the negligence and strict tort liability frameworks using actual cases in which a decision was rendered. It is evident from these cases that some of the successful claims under the strict liability framework would not have been successful, and probably not litigated, under a negligence framework, which could result in substantial cost savings to the blasting industry and consumers.

Jan 1, 2004

By BernardThierry

To be able to precisely predict the result of a mine blast before pressing the button is a goal for many blasters due to the environmental and economic constraints of our century. Based on the fundamental fracturing of the mechanism of rocks by explosives, the most recent research in digital modeling, the power of present computers, and the possibilities offered by drones, we have designed a realistic digital 3D simulation model for mine blasts. This new type of model enables us to concurrently simulate the fragmentation of the rock, its movement and the associated seismic levels, all within a few minutes, which is a time compatible with a production cycle. Due to the complexity of the model, this article reveals the main principles and compares the results of simulations with on-site measurements in various sectors, i.e. quarries, mines and tunnels.

By Conny Sjoberg, Finn Ouchterlony, Bjorn Jonsson

This contribution reports an investigation of the blasting damage in the contour of an access ramp to a Swedish underground laboratory for nuclear waste related studies. Near zone vibration measurements were made for 7 rounds and the results converted to a site specific scaling law. A simple engineering correction for the influence of the charge length wee developed and the resulting equations used to predict the damage zone depths of three different drilling and charging patterns.

Jan 1, 1993

By Robert J. Nothnagle, Kristen Franz Begor, Rodney W. Sutch

Recovery of contaminated groundwater in a fractured bedrock system presents some unique problems. Typically, the most common problem occurs from the inability to adequately characterize the discrete fractures through which contaminants may be migrating. Without adequate characterization, difficulties arise in properly positioning recovery wells and verifying the performance of the system. To overcome these difficulties at a site in Upstate New York, an innovative approach was developed involving the creation of an artificial fracture zone through controlled blasting to intercept contaminated groundwater flow.

Jan 1, 1988

By Julio Cesar Barbosa de Freitas, Rafael Gonçalves Araujo, Túlio Soares, Jair Koppe, Augusto Ferraz Ribeiro, Pedro Barreto Garcia

This study thesis was motivated by the fact that it is of fundamental importance for open pit mining that the slopes initially have a geometry in accordance with what is proposed in the mining planning. This occurs because an inconsistency in this design can impact the operational safety and economic solutions of the mining project. These consequences can be explained by the fact that rock blasting close to mining limits requires specific study due to the attention required. Because, when this operation is not carried out properly, the mining plan in the mine may not be respected and may create risks to the operation due to the presence of unstable blocks on the slopes (Mackenzie). In this sense, Mackenzie (2004) cites pre-split, trim blasting and buffer as commonly used explosive blasting techniques that aim to limit damage beyond the projected wall. Therefore, Enaex Brazil realized the need to better understand the pre-split method. To do this, it is necessary to understand how the energy released during detonation is perpetuated in the rock mass when this technique is used and when it is absent. Thus, this analysis is based on a seismic study that allows the creation of vibration attenuation laws and an elementary wave damage model, which allows the local characterization of the rock. With this model it is possible to relate the peak levels of vibration during blasting and the extent of damage, but a critical level of vibration (PPVc) and its relationship with the Uniaxial Comprehension Resistance (UCS) are also defined for the start of fracturing and its level (McKenzie et al, 1995). And, mainly, this work aims to address a way to measure the pre-split filter potential by comparing the attenuation law with and without pre-split, ultimately knowing whether this finishing blasting is being effective, to understand the pre-split filter capacity.

Jan 21, 2025

By Gloria Contreras

The study aims to optimize the density of holes per tunnel section. The energy distribution, the one with the highest density, is used in the center of the diagram and is distributed homogeneously towards the contours with the lowest energies up to the contours to produce a perimeter control.

Feb 1, 2020

By Robert Pumpelly

During my nearly 30 years with ATF, (Bureau of Alcohol, Tobacco, Firearms & Explosives), I conducted hundreds of inspections. In many cases hours of time were wasted because the licensee or permittee, who had basically done everything right, was not prepared for the audit. In these cases, required documents were scattered, personnel were unprepared and no plan was in place. This paper will provide some simple steps to avoid these embarrassing delays. A list of common violations is also provided.

Jan 1, 2010

By Hubert den Dikken

ache, especially when it comes to forwarding of small quantities. Air transport is limited to 1.4 explosives on cargo aircraft and 1.4S classified explosives on passenger aircraft, so most samples cannot be transported by air. Ocean transport is a possibility, but due to stowage and segregation regulations of the IMDG code, a very expensive one. Road transport is often the only solution, but high explosives require special trucks with licensed drivers. The solution to these logistic problems is solved by creating a 1.4S (Class C) classification for all high explosives, when packed in special containment vessels.

Jan 1, 1995

By L. Muñoz, L. Steffen, W. Vilas

The emission of particulate material is one of the several parameters related to environmental control in mining operations near communities. Blasting is an event that generates and leaves a large amount of dust in suspension, which can cause discomfort to communities, generating complaints that can compromise the operational continuity of the mine. The proper management of these environmental impacts is a key factor to ensure a good relationship with the neighborhoods, making a responsible mining in harmony with the environment, giving sustainability to the mining business in the medium and long term. The main goal of this work is to present different techniques and technologies applied in a large-scale open pit mine in Brazil, with operations close to a community, to minimize the emissions of particulate material into the atmosphere. For this, different technical solutions were implemented. First, a non-conventional blasting technique was introduced that incorporates special charging and timing configurations, generating a first upper layer that serves as a blanket to contain a second, higher-energy lower layer. An optimal stemming was also defined in order to minimize ejections and maximize cratering, using the scaled depth of burial theory as well as video and fragmentation analysis. In addition, changes were made in the timing between decks (to guarantee a minimum time between layers) and between holes (changing the initiation point opposite to the free face). Finally, additional measures such as humidification of the bench, use of a wind vane to identify wind direction and the construction of a physical barrier between the mine and the community were implemented as additional mitigation measures. By applying the above techniques together, in some specific zones of the mine, it was possible to considerably reduce the ejections generated by blasting versus conventional blasting without the above measures, which was demonstrated in the field with dual blasts trials. Additionally, it was possible to achieve a vibration reduction in the community of ~30%. This work demonstrates how, by applying these technical solutions, it was possible to minimize the dust and vibrations generated by blasting allowing this operation to do sustainable mining

Jan 1, 2024

By James R. Houston, Wendel Clay Chaffin, John Loviza

During the spring and summer of 1993 the largest pipeline in Tennessee was installed as part of the upgrading of Nashville's sewage needs through the year 2035. This new 3.3 million dollar outfall project is able to carry 330 million gallons of treated sewage water daily. Special projects required special equipment as this project was safely and quickly installed.

Jan 1, 1995

By Adrian Moore, Alan Richards

A real-time system for prediction of the effect of meteorological conditions on airblast overpressure levels has been established in the Hunter Valley Coalfield in Australia. Real-time meteorological data from continuously operating sounding equipment and a predictive meteorological model is input to an atmospheric refraction model that enables the effect of meteorology on airblast overpressure levels in the area surrounding the blast site to be evaluated. Graphical outputs from the model, which are superimposed over a scaled airphoto of the mine and surrounding area, show the extent that airblast levels will be increased. When combined with inputs that quantify the effect of blasting specifications, the airblast levels that will result in the surrounding area from the combined effect of blasting specifications is determined. The model permits those responsible for blasting to make more accurate decisions on suitable times that blasting may take place to conform with applicable airblast limits.

Jan 1, 2009

By G J. Kulbieda

The Empire Mine initiated production in 1963. Since then the unit operations of drilling and blasting have evolved continually in order to meet the increased mining requirements demanded by plant expansions in 1968, 1973 and 1980. Additionally, advance mine planning has become an integral part of proper pit development and is necessary to insure uniform blending of the distinct ore horizons contained within the mine area. Blasting practices have been modified to facilitate the autogenous grinding system utilized at Empire and pioneered in the Iron Ore Industry. Technical innovations in the explosives industry, as well as, progress regarding on site blast engineering methods have substantially increased the use of ammonium nitrate explosives and helped to establish efficient charging procedures. In addition, the recent introduction and use of ammonium nitrate fueled with nitropropane and methanol indicates that it is a viable substitute for aluminized ANFO.

Jan 1, 1981

By Jorge Cárdenas, Luis Huaroc, Máximo Cari, Nestor Delgado

In Peru, after four years of pandemic, some mining companies have chosen to install integrated operating centers in central offices where through network technology and video surveillance it allows them to carry out their activities remotely, this has become a disruptive strategy to promote a safer and smarter mining industry. Our fundamental value is to improve the quality of life, safety and well being of our collaborators, that is why we have created the remote blasting engineering control center " Core" that allows us to humanize mining. Core is an integration of experience, security, technology, quality of life and artificial intelligence; it has media technology connected directly to the mining operation, specialist engineers and technical assistants in team they seek to create optimal proposals of drilling and blasting designs remotely that generate added value to customers. In the planning process the team suggests drilling meshes, in the loading process there are optimized, digitized designs and efficiency in the factory trucks finally in the safety process allows us to identify inadequate pipes within the blasting project, deviation of procedures, remote inspections, identify operating conditions to prevent future risks that may arise in the blasting process. The remote communication systems allow you to monitor mining operations remotely to identify and alert any operational or security deviation that was not identified by the personnel present in the operation, as well as to store images in case investigations are required. The results obtained have allowed us to reduce the exposure of personnel to any risk of the mining operation, to optimize times in the activities of our engineers who are in the mining operations since there is the permanent support of centralized specialists to face every challenge that arises in the operation, for the engineers who are in the offices of Core can be very close to the family and do not lose it, and for our customers it is to meet their needs with engineers specialists in the drilling and blasting process, as well as in safety to be able to proactively cope with any deviation that arises.

Jan 21, 2025

By Hernan Navea, Carlos Alvarado, Exequiel Nuñez, Matías Suarez, Jhon Silva, Bryan Townsend, Bryan Caceres, Felipe Pontanilla

Nowadays, technology dominates all aspects of human activities, and drilling and Blasting (D&B) is no exception. In most cases, the use of technology in D&B is focused on controlling individual activities such as drill performance, drilling advance rates, truck loading performance, etc. Still, in very few instances, the advantages of using technology along each D&B activity and how this influences the D&B results are documented. This paper shows how technology is applied to create a “relative hardness” model for the mine Caserones in Chile. In the future, the model can relate the relative hardness parameter to several variables, including excavation rate, fragmentation results, and vibrations. It can also be used in the explosives loading process, similar to the model used by Dyno Nobel’s Differential Energy (DE) technology. In the relative hardness model for Caserones, a design is loaded in the drill system, and data is collected during the advance of the blasthole. The collected data includes rpm, torque, pressure, etc. Then, an algorithm using the measured variables while drilling and known relationships between the properties of the rock and the drill's performance is used to classify the average relative hardness of the blasthole in four intervals: hard, medium, soft, and very soft. Optimization techniques and models used in the oil and gas industries to analyze drilling performance were adapted to implement the algorithm. The model uses the concept of mechanical specific energy (MSE). Using the data from the drill, the algorithm identifies the depth where the MSE reaches a minimum to calculate the “relative hardness” for the blasthole under analysis. The results are presented in maps highlighting the areas where hard, medium, soft or very soft rock masses are expected. That information can be used to anticipate areas where explosives with higher energy need to be used or to predict areas of the blast with additional digging difficulties and then lower loading rates. The paper shows examples where “relative hardness” maps are compared to drilling speed excavation rates and other variables.

Jan 21, 2025

By Eric C. Gerst

"In this current era of soft commodity and coal prices the mining industry is turning towards optimizingall levels of production to reduce operating costs. Part of this trend includes the automation of miningmachines. As the first tier of the mining process blast hole drill automation offers benefits through the entire value stream from drill bench to material processing."

Jan 1, 2017