Search Documents

By Robert Hopler

After the disbanding of the Gunpowder Trust Association in 1904, the Association of Independent Powder and Dynamite Manufacturers was formed, followed in May of 1906 by the formation of the Association of Manufacturers of Powder and High Explosives. Due to a lack of success in attracting all manufacturers to membership, these organizations did not survive.

Jan 1, 2014

By N Gkikizas-Lampropoulis

Selection of delay times to optimize fragmentation has been a controversial topic among researchers and blasting practitioners. This paper interprets previous experimental information on the effect of delay on fragmentation with the aid of some new experimental observations of the time of detachment of the free face of the blast as well as results of numerical modelling. It was shown that detachment of the burden occurs at delays shorter than the one which produced optimum fragmentation in the experiments, suggesting some fragmentation improvement due to gas action. In addition, at the spacing to burden ratio of the experiments, the damage zone from an earlier detonating charge extends the distance to the neighboring charge, essentially affecting the burden of some of the holes of the blast, at detonation time. Computer modelling demonstrated that increased spacing results is less overlap of stress induced damage zones meaning that there is less influence of delay on stress wave induced fragmentation. It was also shown that simultaneous initiation results in less back break, while increased back break may result even with short delay times.

Jan 1, 2016

By Andrew P. Ritter, James W. Reil, Douglas A. Anderson, Stephen R. Winzer

We have developed a method for predicting and controlling ground vibration from blasting using a rigorous scientific approach. The method is based upon the superposition of seismic waveforms generated by a single-hole free-face shot, recorded at seismographs deployed in an array that includes environmentally sensitlve locations. Waveforms generated by single-hole shots are shown to be reproducible. The waveforms for each of the sites are used to construct synthetic seismograms for delayed shots based upon linear superposition. A computer code systematically constructs the seismograms for the delayed shots, with incremental delays between holes of 1, 2, or 3 milliseconds (ms). A Fourier amplitude specs-rum is calculated for each synthetic seismogram and the spectra are plotted on a map in delay-frequency space, i.e., each row of the map represents the Fourier spectrum for a blast with a particular delay interval. For single-row shots, the delay between holes in a row is used; for multiple-row shots, the delay between holes In a row is kept constant and the delay between rows is incremented. Predicted vibration varies strongly as a function of delay and h

Jan 1, 1985

By J. Aravena, S. Gajardo, M. Ayala, P. Salinas

Both, Teck Carmen de Andacollo (Teck CDA) and Orica, work hard in the implementation of new technologies available in the explosives industry and drilling and blasting techniques, with the objective of sustainable development of their operations, regeneration, and protection of the environment, also considering the welfare and relationship with the surrounding communities. The open-pit Carmen de Andacollo mine is located adjacent to the town of Andacollo. Therefore, both companies together have developed the implementation of different techniques and technologies to mitigate the impacts of mining operations in the community, considering an important part of this challenge to minimize the impact of their perception of blasting by reducing the level of vibrations and sound pressure (airblast), in addition to the control of dust and smoke, strengthening sustainable production in harmony with communities. The technologies and techniques that have been implemented are the installation of airblast and vibration monitoring stations stands out, whose database has records since 2011. Using the vibration database, different models were developed to predict the vibration level of blasting in its design phase, achieving a difference of 4.1% between the estimated and measured values in the last year. Two techniques stand out to minimize the ejection of material, "Hydraulic Dome" and "Dual layer blasting", the first consists of water irrigation on the surface to be blasted and the second is an unconventional blasting technique, which was awarded in 2015 for its results in the environment. Also pre-splitting engineering has been modified in a positive evolution, where through different configurations, the airblast has been reduced by 15% compared with records from 2011 to 2022. Finally, due to the impact of operational restrictions, such as days available to blast, number of holes, and powder factors, the wireless initiation technology was implemented, which allowed reducing the limitations in the loading, generating an improvement in terms of blasted materials over conventional systems. Understanding the restrictions and challenges in terms of impact on communities, the correct implementation of all these techniques is important, and in conjunction with collaborative work, it has been shown and validated that producing in a sustainable and sustainable manner is possible.

Jan 1, 2024

By Brad Bockey

Whether you are a driver, blaster, or are in charge of filing, you must recognize the importance associated with DOT-required recordkeeping. As various agencies become intertwined with rules governing the explosives industry, the records we produce must be as accurate as possible. The time is right for reviewing your paperwork process from start to finish.

Jan 1, 2011

By William Reisz

The explosives and blasting industry has a commendable safety and security record, especially over the last several decades. This is due in large part to our newer technologies, better training and education, engineering practices, corporate initiatives, our professional organizations, and whether we like to admit it or not - our regulatory agencies.

Jan 1, 2012

By (Journal for the Fields of Gunpowder and Explosives) Germany (1914 Issues)

RBH Note: The following items are a deviation from the usual content of these articles, but I thought they were kind of interesting from an historical point of view (other than just explosives-history historical.) The interesting things to me are the military-related products, keeping in mind that World War I didn’t start until August, 1914, and then it was kind of an accident of political alliances gone awry. Obviously companies in Germany saw it coming. Of course, all the ads also included dynamite and safety explosives for mining and tunneling as well as the military items.

Jan 1, 2015

By Ronald L. Sanders

The prevailing view of the coal mining industry by government officials is: "Tell everyone you're coming - Don't let anyone know you're there - And remove all evidence you have ever been there". Now the irony is that the government inspectors are just enforcing the law. The coal mine operators seem more interested in genuine reclamation than the inspectors.

Jan 1, 1979

By Jane Wright, Brent Blanchard

Question: When it comes to demolition projects, what could be more demanding than asking a blaster to explosively demolish a stubby, heavily-reinforced concrete structure in the heart of a third-world country? Answer: Asking them to fell only half. Such was the charge recently put forth to Controlled Demolition Group (CDG), Yorkshire, UK when they were called to Casablanca, Morocco to provide a stunning demolition effect for the upcoming Universal Pictures film Spy Game, starring Robert Redford and Brad Pitt. Director Tony Scott (True Romance, Enemy of the State) contacted the renowned demolition firm after seeing their work on television and receiving recommendations from explosives manufacturers. The film’s producers then asked the CDG team if they could bring down half of an apartment block as part of a dramatic suicide bomber sequence.

Jan 1, 2002

By Rolf Koenig

After the Dynatronic firing system was demonstrated for the first time at the SEE conference in Miami in 1987, it was officially approved in Germany at the beginning of 1993. Dynatronic has now been on the market for 5 years. At present, it is used in several European countries and successful test series have been running in Australia.

Jan 1, 1998

By Tom Snyder, John Brulia

PART 3 – UN Identifi cation Markings for the Highway Transportation in Commerce of Bulk Explosives, Oxidizers, and Combustible Liquids

Jan 1, 2015

By R. F. Favreau, Patrice Favreau

In many quarries and construction sites visited by the authors over the last 50 years, the latter have observed muck piles from blasting with explosives, which included numerous large blocks, in some cases of dimensions larger than the input to the crusher. The names of these sites cannot be given in the article because the owners insist that data obtained on such visits be kept confidential. Often the blasters felt that the natural fissures in the rock would compensate for the use of a low powder factor, and they asked the authors to explain why such blocks were present. A detailed analysis of the situation often indicated that the cause of the blocks is that explained by figures such as 6 and 7 below in the article.

Jan 1, 2018

By Tom Goodell, James Cox, Scott Scovira

Resolution Copper Mining is sinking a 6943 foot (2116 m) deep shaft to access and develop a new panel caving mine with approximately 1.6 billion known tons of porphyry copper resource. This mine will take several years to ramp up to its full production level of 132,300 tons per day (120,000 tonnes per day) and is scheduled to begin production in the early 2020s. Resolution's shaft sinking contractor Cementation USA is using state of the art sinking methods combined with a largely local labor force to complete this record breaking shaft. Resolution's No. 10 Shaft has finished diameter of 28 feet (8.5m) and as of October 2013 is at the 6625 foot (2020 m) level. Upon completion in early 2014, the No. 10 Shaft will be the deepest single lift shaft in the United States.

Jan 1, 2014

By Guillermo Lazcano Ríos, Jorge Parvez Aguirre, Alejandro G. Díaz Berríos, Felipe Rodriguez Alveal

Codelco's Chuquicamata Underground Division (DCHS) faces issues due to collapses in its subsidence streets, which hinders the advancement of the subsidence front and leads to the loss of areas and reserves. To address these issues, DCHS and Orica have developed a new excavation methodology based on pre-loading explosives in high drawbell. This methodology involves creating a high drawbell extending from the floor of the production level to the ceiling of the subsidence level, divided into two phases: upper and lower. A resin stemming is used to separate these phases. The excavation strategy adjusts to variables such as reception volume, fluffing, and excavation geometry, involving vertical pre-loading of the explosive and the use of a separating element between the phases. The test aims to validate the new excavation methodology and the retaining element in the rock mass, evaluating aspects such as drawbell geometry, impact on the rock mass, damage to the retaining element, and fragmentation. Wireless electronic detonators are used in the upper phase to improve safety by eliminating the need for physical connections, while traditional electronic detonators are employed in the lower phase. Low-density bulk emulsion is applied to minimize the impact on the Crown pillar and extraction point, and higher-density explosives are used above the subsidence level to ensure good caving. Results showed that the blast achieved 86% conformity with the theoretical design. Resin stemming allowed for 100% effective detonation in the upper columns, and the fragmentation obtained was 5.44 inches, which was less than expected. No damage to the Crown pillar was observed, and the explosive quality met standards. This technique has proven to be effective and viable, suggesting the possibility of eliminating the subsidence level in future levels, resulting in savings, and providing greater stability to the rock mass.

Jan 21, 2025

By G Alan Foster

Many complaints generated from blasting operations result from the marked human response to ground transmitted vibrations and air blast effects and so many authorities have considered the regulation of blasting in terms of human response rather than, as previously, in terms of preventing damage to structures.

Jan 1, 1981

By Alastair Torrance, George Boucher, Roger Keller

An investigative blast programme has been carried out to provide information on the best blasting methods to excavate Chek Lap Kok island in Hong Kong for the new airport. The objectives of the programme included the assessment of a range of blast design parameters and their influence on fragmentation. This has been evaluated by physical assessment, photo digitising of the muckpile and computer predictions. In addition, a model to predict the three dimensional muckpile shape has been successfully calibrated.

Jan 1, 1992

By Saeed Karimifard, Saman Nouranian, Shahram Tafazoli, Bahram Sameti, Frank Chu, Caitlin McKinnon, Tetiana Konstantynivska, Glen Turner

Continuing blast optimization is the cornerstone of any mine-to-mill approach, and particle size analysis is a key metric for meeting blast targets to reduce overall energy consumption and operating costs. To ensure the statistical validity of particle size data, it is important to sample material frequently. In most mines and quarries, the blasted material is loaded onto haul trucks and then transferred to the crusher; measuring the particle size of each haul truck load therefore provides an adequate sampling rate. We propose a particle size analysis solution for haul trucks that does not impact current operational workflows. Using artificial intelligence (AI) and 3D imaging technology, our solution reliably localizes and identifies haul trucks as they drive by, then accurately calculates the particle size distribution of the visible material in each truck load. In this paper, we identify the challenges of designing and implementing the proposed solution and explain the strategies we employ to overcome these. We also discuss a method for boulder detection that leverages the existing deep learning architecture to significantly reduce crusher downtime caused by oversized rocks. Finally, we present field data from a trial installation. To evaluate each change made to the blast design, it is necessary to measure the effect on particle size. An accurate particle size analysis solution is therefore the first step towards optimizing blasting practices and reducing energy consumption throughout the comminution circuit.

By Barbara Rutter, Phillip Mulligan

This research investigates how changes in shock tunnel geometry affect the pressure versus time waveform. The Large Arena Test Simulator (LATS), which is composed of four different rectangular sections connected by three expansion sections, was used to determine how the changes in geometry affect the shock wave profile.

Feb 1, 2020

By Paulo Couceiro, Juan Navarro

The impact of rock blasting fragmentation and heave on digging performance in open-pit mining operations is usually the first true indicator of blasting outcomes. Within the typical excavation cycle, the bucket loading time or instantaneous digging rate are the ones that present the strongest correlation with rock fragmentation size distribution, swelling, and shape of the muckpile, a part of rock mass hardness, equipment size, power, and others. As the efficiency of unit operations becomes increasingly important for long-term mining strategies, cost-effective approaches are needed to increase mine productivity. In this line, the performance of downstream operations, such as digging, hauling, and comminution, may be affected by the energy input in blasting. This requires a better understanding of the explosive’s energy role in such unit operations in order to drive consistent improvements. Therefore, this paper examines the impact of the explosive’s energy distribution on shovel diggability from production shots carried out with different explosives in an open pit gold mine, with the aim of modelling the interface between blasting and excavation.

Jan 21, 2025

By Catherine Johnson, Barbara Rutter, Phillip Mulligan

Shock tubes, shock tunnels, and blast tubes have been widely used by explosive researchers and shock wave investigators to understand the characteristics of shock waves. Rectangular, cylindrical, and conical are the three simple geometries commonly used in shock tube and shock tunnel testing. These geometries result in shock waves that resemble the Friedlander curve’s simple exponential decay. However, geometries that are more complex have not been studied. This research investigates how changes in shock tunnel geometry affect the pressure versus time waveform. The Large Arena Test Simulator (LATS), which is composed of four different rectangular sections connected by three expansion sections, was used to determine how the changes in geometry affect the shock wave profile. Shock wave profiles were measured inside and outside the LATS to investigate the geometry’s effect. A representative shock wave profile from each geometry and open-air explosive testing were compared visually showing the geometries effect on the shock wave profile. The LATS produced a waveform with four pressure peaks behind the initial shock front, which were found to be associated with the four rectangular sections. The resulting pressure trace was compared to pressure traces from simulated urban bombings. The number of turns in an urban environment equated to a new peak, which is caused by additional expansion sections of the shock tunnel. From this observation, complex geometry shock tunnels can be purpose built to simulate an explosion in an urban setting. The use of shock tunnels with complex geometry in simulating urban bombings can allow for numerous representations and a better understanding of profiles produced during an urban bombing or similar scenario.