Search Documents

By T Guiliani, F Ottuonye

Explosives casting is gaining increasing popularity as an overburden removal method in strip mining because the coats of using explosives to cast a percentage of the overburden to the spoil are lower than the costs of using stripping shovels or draglines to do all the overburden removal. This is due to the rising capital and operating costs of draglines and shovels.

Jan 1, 1989

By Thomas M. Keevin, Gregory L. Hempen

A user-friendly model for environmental effects from underwater explosions is presently available. The model by Munday et al. (1986) is effective for determining fish mortality radii from underwater shooting. The IBLAST program (Coastline Environmental Services 1986) from this model includes estimates for both borehole-loaded explosives for demolition or rock removal purposes and midwater shots. Midwater shots may be used for fish population assessments or some seismic surveys. The program produces approximate mortality distances for planning purposes. IBLAST does have serious shortcomings of which users should be aware.

Jan 1, 1995

By Robert Hopler

GEO. M. MOWBRAY’S REFRIGERATOR CAR FOR THE SAFE CONVEYANCE OF EXPLOSIVES. It is a fact well known to all miners who have used nitro-glycerin, or any of its adulterations, commonly known as dynamite, rendrock, Hercules’ powder, dualin, vigorite, etc., that when congealed, these compounds cannot be exploded, and in this congealed state — say at temperatures below 40° F. — they can be handled with no more danger than a box of soap or a can of lard. If, then, the atmosphere by which this class of explosives is surrounded, during transportation, be maintained below 40° F., explosion is practically annihilated. Therefore, I constructed a refrigerator car, with cells for every box of the explosive; and two years of railroad transportation confirms our ten years’ experience in teaming in wagons, that this class of explosives can be transported in perfect safety, as above described.

Jan 1, 2011

By Romel B. Villanueva

At the Yanacocha gold mine, in the Andes of northern Perú, the first instrumental tests were carried out in October 2019 to detect the initiation sequence of a production blast by detecting the EMF signal produced by the detonation from each blast hole in the sequence. Several experimental tests were carried out to choose the correct antenna and find the best setup of the high-speed Data Acquisition device (DAD) to detect these electromagnetic waves. Finally, the first measurement was obtained. With the instrument recording at a rate of 1 million samples per second, the initiation sequence was detected with 99.5% accuracy. It was found that it corresponded, without a doubt, to the designed scheme. The main result is that these tests provide us with a method and instrumentation to verify if the planned initiation sequence is carried out correctly in the field. In this way we can find operational deviations and detect possible misfires. This method has proven to be accurate, fast and easy to implement, mainly requiring an EMF signal capture equipment that can record at very high speed, something that is increasingly easier to satisfy with the development of microcontrollers. On the other hand, the type of antennas used in this method are low cost and very commercial. These tests have improved our understanding of the nature of detonation and have marked a new milestone in the development of blasting instrumentation in Peru.

Jan 21, 2025

By R. Ranjan

Stanstead granite has been investigated with respect to its dynamic compressive strength and its strain-rate dependency. A standard Split-Hopkinson Pressure Bar (SHPB) apparatus has been employed to generate strain rates of up to ~500/s through high-velocity impact. The diameters of the test samples were 19 mm, and tested under impact velocities up to ~20m/s. It is found that even within this limited range of strain rates, the dynamic compressive strength for the granite showed nearly a 100% increase in value compared to those obtained under static loading conditions (e.g. compressive strength of 394 MPa at a strain-rate of 600/s, compared to 215 MPa obtained under static loading). The details of the test are described in terms of incident, reflected and transmitted stress pulses, along with means to achieve stress equilibrium in the test samples under dynamic loading conditions. The advantage and drawback of the use of ‘pulse shaping’ techniques to achieve dynamic stress equilibrium are also detailed.

Jan 1, 2010

By Sami Kara, Marsel Nabium

This paper provides an overview of the solution applied in underground Silver mine in Russia. The paper reviews the dilution problem throughout the entire mining process, and provides a rational approach to underground mine Blast design in order to minimize dilution

Feb 1, 2020

By Karl Christopherson, Vanessa de Viterbo

Trim blasting is an integral part of the mining processes at the Morenci Mine, a Freeport-McMoRan Copper & Gold Inc. property. Trim blasting near high-walls or Finals blasting requires a tighter distribution of energy but a reduction in total energy factor near the wall. Recent Finals blasting in Morenci Mine was allowing the shovel to dig to the final design limit, but causing high-wall instability due to excessive energy or production of energy (blast design and timing). Slope instability events reduced production in two of the three operating pits in Morenci over 2009. In order to avoid high-wall instability from Finals blasting, a new method was required. The new method utilizes air-decks, unconventional row timing, and blast design based on the geology predicted. Many different geologic structures and rock types exist in Morenci, and different strategies were needed for the many predicted geologies. Drill penetration rate and core mapping were the primary tools for determining the blast design. Patterns were designed within a consistent geology; with weaker rock types receiving a lighter load than the stronger rock types. Penetration rate returned by the drill would be the determining factor on the actual rock hardness. Maintaining the pattern geometry on Finals designs should not be an issue as long as the lb/hole is adjusted to reduce powder factor close to the high-wall. One requirement of Finals blasting should be that the powder factor matches the geology as closely as possible. A softer, fractured zone should use approximately one-half to two-thirds the explosive charge of a competent, sound geological zone. This has been incorporated into the final Trim blast design. It is impossible to protect every high-wall from close-in blasting, especially those with crossing prominent joint sets inclined toward wedge failure, but this new design has provided protection on walls where the mine was encountering problems.

Jan 1, 2011

By John Cory, Ran Tamir

Blasting data analytics are being increasing used to increase mining productivity, reduce mining costs, maximize high margin aggregate products, and to reduce fines. Three examples will be illustrated using simple models to maximize the percentage of blasted rock within established dimensions and reduce fines-one from video fragmentation distribution information, the second from sieved crusher fragmentation data, and the third from plant production data. In addition, the use of sieved crusher results to determine blasting related fines and the use of mine productivity data to maximize aggregate sizes when pattern (burden and spacing) areas are changed will be illustrated

Jan 1, 2012

By Christodoulos Xiouris, Ali Reza, James Karnesky

A rocket parachute signal flare is often used to signal a maritime emergency. In the general operation of these devices, a solid rocket motor propels a metal body to an altitude of approximately 1000 ft(305m).At the end of the rocket motor, a propelling charge drives a signal flare and parachute out of the metal body and ignites the flare, which then burns for approximately 40 seconds as it falls to earth. In this paper, we describe an engineering investigation of an accidental ignition of a rocket parachute signal flare, which caused injury to the user. The components of the flare involved in the accident were inspected via x-ray and microscopic imaging techniques, and compared with those of unfired flares recovered from the same vessel. Chemical analysis of residue on recovered components from the accident flare was also performed. These comparisons were used to determine the likelihood that the actuation mechanism had been deliberately manipulated. In the subject model of the flare, ignition of the rocket motor is accomplished through a percussion cap which is struck by a firing pin. Prior to activation, the firing pin holds down a pre-compressed spring. We present a comparison of the ignition system of the incident flare with those of other rocket parachute flares, which do not incorporate any stored mechanical energy.

By Seokbin Lim

According to published literature, the equation of motion of linear shaped charges (LSCs) has been investigated as early as the 1960s in a few research organizations. However, due to the comparatively low penetration performance, the amount of research has not been extensive, and the use of this device is quite limited in very specialized applications. Traditionally, the equation of motion of an LSCs’ liner shares the same basis as conical shaped charges (CSCs) because they are under the same functional category and generally have similar geometric configuration. However, the nature of LSCs is not quite similar with that of CSCs due to multiple reasons, and they required a new set of equations to properly address their performance. In this paper, we reviewed different sets of approaches in describing the liner collapse behavior of LSCs mostly based on the author’s contributions.

Jan 1, 2014

By Roger Favreau, Patrice Favreau

The article reviews the aspects which contribute to the quality of the results from a blast with explosives, namely a good floor, no large blocks, easy mucking, and explains the mechanisms of the blasting process which decide on the quality of these aspects for a given blast method, and how these mechanisms can be simulated from basic principles. It proposes that good fragmentation size distribution can also be important if the rock is going to a crusher, e. g. for the ore in a mine and for the rock excavated in a quarry.

Jan 1, 2012

By Rowland Jones

This type of quarrying is very much different from that of established quarries in developed countries, demanding somewhat unorthodox techniques to produce the variety of materials required. The demands on the resourcefulness of-the quarrymaster can be very testing, and produces quite a different breed of individual than what is normally met in managerial status in quarries of developed nations.

Jan 1, 1977

By D D. Garg, D A. Wasson

Open pit blasting in India uses two types of explosives. First there are bulk explosives for wet and dry holes, and there are packaged explosives. The Indian open pit coal mining is projected to use 190 thousand metric tons of explosives in 1995. This volume is projected to grow for the next ten years, whereas the underground coal mining will hold fairly constant.

Jan 1, 1995

By John T. Day, Lex L. Udy, Mark L. Thomas

When we consider that the purpose of blasting is to fragment rock or ore so it can be subsequently handled and processed, we can see that the cost of blasting, in reality, affects all downstream steps of the mining (and in some cases) production processes. The productivity of all subsequent operations is influenced by the degree of fragmentation of the primary blast.

Jan 1, 1987

By Christodoulos Xiouris, Ali Reza, James Karnesky

A rocket parachute signal flare is often used to signal a maritime emergency. In the general operation of these devices, a solid rocket motor propels a metal body to an altitude of approximately 1000 ft (305 m). At the end of the rocket motor, a propelling charge drives a signal flare and parachute out of the metal body and ignites the flare, which then burns for approximately 40 seconds as it falls to earth. In this paper, we describe an engineering investigation of an accidental ignition of a rocket parachute signal flare, which caused injury to the user. T

Feb 1, 2020

By K. Hausmann, P. A. Sashin, G. J. Prejean

Misfires caused by unreliable shock tube constructions can have significant cost implications and place field workers at serious risk during remediation. Ionomer materials, used as a subtube in shock tube constructions, provide superior hot tack strength, oil resistance, impact resistance at cold temperatures and excellent thermoformability properties. These are important features for resisting blast-throughs and ensuring blasting reliability in demanding environments, such as open pit mining in harsh environments. Superior hot tack strength, strain hardening, and excellent thermoformability properties of the ionomer materials ensure uniform powder distribution along the shock tube during construction and avoid undesired powder accumulation due to deformation or vibration during use. Oil or chemical resistance is another feature of Ionomers. This allows improved property retention in contact with oils and hence longer sleep times of the shock tube. Another feature of these highly engineered ionomers is superior impact strength at low temperatures. This plays an important role considering the resistance to fly rock impact in open pit mining operations in particular in cold climates.

Jan 1, 2011

By Timothy Stark

At present blasters are strictly liable under tort law for personal injury and property damage caused by ground vibrations and/or air overpressures. The application of strict tort liability to vibration and air overpressure damage has resulted in litigation that has hampered and probably will continue to hamper the blasting industry. There are many case histories in which blasters have been sued for the appearance of cosmetic cracking, some of which have involved frivolous claims and marginal expert testimony (Oriard 1999). This litigation has resulted in additional costs to the blasting and construction industries and the American public because there are usually many plaintiffs involved and each case is usually adjudicated separately instead of under a class-action format. It is proposed herein that blasters not be held liable for vibration or air overpressure damages unless their conduct is proven to be negligent. A number of reasons are presented for raising the legal standard from strict liability to negligence including: (1) improvements in blasting technology that allow blasting to be conducted without substantial risk of damage and if damage does occur it is likely to be cosmetic, (2) establishment of conservative ground vibration and air overpressure damage limits for typical structures, and (3) established industry standards for construction blasting.

Jan 1, 2002

By Clayton Thompson

Linear detonation wave generators (DWGs) shape a detonation wave so that every portion of the wavefront reaches the target “line” simultaneously. A projection-type linear DWG uses Gurney plate velocity predictions and Taylor deflection angle predictions to estimate the angle at which a thin projected flyer (typically metal) will impact a target. A mousetrap-style planar DWG consists of two projection-type linear DWGs working in succession to create a planar wave-front through shock initiation of each successive target explosive. The angle of deflection is critical to yielding a planar or linear wave profile. Gurney predictions, nominally accurate to within 10% of empirical results, may not yield ideal linear or planar detonation behavior when used with a grazing projection-type DWG, which typically requires accuracy within 2%. Simulations were conducted using AUTODYN hydro code to compare deflection angle prediction methods. Ranges of minimal error between Gurney and Taylor predictions and the results from the hydro code were determined, using PBX-9404-driven polyethylene flyers.

Jan 1, 2011

By Benjamin Cebrian

Rock blasting at quarries represents multiple challenges not easy to see at first sight. Aggregate industries face similar or superior prices for explosives while extracting a material that usually is of less value of metal mining operations. Therefore, learning to optimize a quarry operation can be a perfect training for a position in blasting at larger metal mining operations.

Jan 1, 2010

By K. Hausmann, W. Whelchel

The properties of ethylene Ionomer resins for the inner layer of non-electric shock tubes will be discussed in detail, and opportunities for property enhancement will be pointed out. A stiffness program for prediction of shock tube stiffness, as determined by the stiffness of the individual layers, will be presented and discussed.

Jan 1, 2010