Search Documents

By Rodney J. Hundermark, Sharif Jahanshahi, Shouyi Sun

"The major platinum producers in South Africa make use of electric furnaces for the melting of PGM bearing nickel - copper concentrates. To gain better understanding of the furnace operation, research was conducted at CSIRO Minerals in Melbourne, Australia. One aspect of the research project was the investigation of the factors affecting the electrical conductivity of melter type slags.Electrical conduction in slags can occur through two mechanisms: ionic and electronic. There is good understanding of the ionic mechanism. In slags containing high levels of iron, the dominant mechanism is electronic. There is limited understanding of the electronic mechanism and one of the aims of the research was to investigate this mechanism further.Experimental work was carried out on Al2O3.CaO.FeOx.MgO.SiO2 slags similar in composition to the melter slags. Conductivity increased significantly with iron oxide content. Above 20wt% FeOx, electronic conduction was significant and the conductivity varied with the oxidation state of the slag. As the iron oxide content was increased further, the electronic mechanism became more dominant. The conductivity reached a maximum at around pO2 = 10-7 to 10-4 atm., although this value was dependent on the total iron oxide content and basicity of the slag."

Jan 1, 2003

Under the sponsorship of the U.S. Department of Energy, a project was completed in 2005, which studied the use of a special pneumatic capsule pipeline (PCP) system, driven by linear induction motor (LIM), for transporting minerals and/or mine wastes. In this study, the pipeline is a rectangular tube of 1m × 1m cross section. The capsules are similar to railroad cars running on small rails imbedded in the tube. A LIM is placed AT the entrance of the tube to transfer power electro-magnetically from the LIM to capsules. The capsules going through the LIM, propelled by the electromagnetic field generated by the LIM, move faster than the air and hence impart energy into the airflow. This in turn pushes the capsules in the tube forward. When the tube is long (say longer than 10 km), additional LIMs may be needed along the tube to serve as booster pumps. An advantage of using LIMs instead of blowers as used in ordinary PCPs is that capsules can pass through the LIMs unhindered. This enables the use of booster pumps for long tubes. It also enables PCP to achieve much higher cargo throughput than that of PCPs using blowers, thereby reducing unit cost ($ per ton-km). Advantages of using capsules with steel wheels running on steel rails in the tubes including: (1) contact friction is only about one-fifth of that using rubber tires, thereby conserving energy, (2) capsules can run at a much higher speed than those using rubber tires without overheating and damaging the tires, and (3) rails make capsule motion control simple; they restrict lateral movement of capsules, and make branching easy-by using standard rail crossing equipment. This advanced PCP system combines the advantages of LIM with the advantages of rails, resulting in a super-efficient tube system having throughputs an order of magnitude greater than that of conventional PCPs, and having an energy efficiency better than railroad transport. Analysis shows that the system is highly cost-effective when throughput is high-at least 5 million tons per year. The system is most suitable for long-distance transportation of minerals (including coal and flyash) and wastes (including both mine wastes and municipal solid waste).

Jan 1, 2014

By M. Bhartia

India is the 5th largest producer of steel in the world and is slated to produce more than 180 Mt by 2020. Expectedly about 50 % of this would be through the Blast furnace route and the rest through Sponge iron / DRI route. Considering that there will not be any major change in iron making technology by that time, the Blast operation would require lump ore (10-40mm) with around 64% Fe grade and sinter fines (<10mm) with 60% Fe (min) as its feed. DRI process would need calibrated ore of size 5-18 mm as the most suitable size of feed. It is also expected that of the total requirement of ore for the DRI route a significant part would be DRI pellets. In India, there is considerable debate going on regarding the technology to be adopted for the processing of iron ore and there is a lack of clear consensus. The above scenario indicates that the processing requirement of iron ore in the country would involve both washing technology as well as beneficiation technology. CDE Asia Ltd is in the forefront of iron ore processing in the country and the experience gained by the company over the last few years of functioning has led the company to believe that route to be adopted depends on the end product requirement and the starting grade of the feed. Keeping in mind the nature of the feed required for the Blast furnace & DRI operation; it is obvious that good washing technology would be highly beneficial to the iron ore industry. Depending on the grade of ore available the limits of washing will be decided and equipment for lump ore beneficiation such as jigs could be incorporated into the washing circuit. Scrubbing of ore either before washing or selectively scrubbing the lumps could be necessary. Very low grade ore and jig rejects would be required to be totally ground and beneficiated for the production of pellet feed in order to utilize the iron ore resources entirely. Another source of ore for pelletisation would be slimes generated from the washing process as well as the huge quantities already available in the tailings dams in the operating mines. Deslimimg and magnetic route of beneficiation could release at 30-40% of the Fe locked up in these tailings ponds/dams. The paper describes the concept with examples from operating plants and proposes how the adoption could be engineered through test work and proper plan of integration. Keywords: washing, beneficiation, iron ore, lumps, sinter fines, pellets, jigs, screens, evowash, nanowash, thickeners, log washers, drum scrubbers

Sep 1, 2012

By F. Y. Kang

Graphite with layers structure is easily to form graphite intercalation compounds (GICs) by means of intercalation reactions due to the weak cohesion force among carbon layers, van der Waal?s interactions. By controlling the oxidation-intercalation, high quality exfoliated graphite with low residual sulfur content and MClx-GICs (M=Fe, Co, Ni, Cu, Zn) powder for electromagnetic wave absorbing and shielding materials have been invented. The expansion volume of expandable graphite can be larger than 160 mL/g while the residual sulfur content is less than 800 ppm. The MClx-GICs powder can shield infrared ray and laser completely up to 15 min. We have also in-vented exfoliated graphite for heavy oil adsorption and mild-expansion exfoliated graphite for anode materials in lithium ion battery by controlling the intercalation/de-intercalation. The exfoliated graphite can adsorb heavy oil up to 80 g/g, it also exhibits better performance than commercial active carbon in sewage treatment. The mild-expansion exfoliated graphite as anode material shows high capacity of 370 mAh/g and good cycle performance.

Jan 1, 2014

By A. S. Choudhary

India is endowed with a reasonably large reserve of chrome ore, amounting to about 100 million tons in different grades and is one of the leading producers of ore/concentrate along with South Africa, Kazakhstan and others. Chromite production in India has registered a 10 times increase during the last 30 years. Till late 1940s, the practice was to mine the high-grade ore for making ferrochrome and charge chrome and export the same leaving the low and medium grade ores stacked around the mine as waste material. This practice was continued for quite some time till the increase in world wide de-mand of chromite initiated an increase in production of chromite ore in India and the aspects of ?economy of operation? and ?conservation of mineral? dawned on the producers and associated authorities. Recovery of chrome values from low and medium grade ore was initiated to produce high-grade saleable concentrate. Suitable legislation was made by Government of India to induce and provide incentives to the operators to do so. First large scale chromite beneficiation plant in India was commissioned about three decades back at Byrapore in the Southern state of Karnataka. The ore, rather simple in nature and relatively free from clay, was obtained from underground. The processing consequently was simple washing and wet tabling. Further more, some test work, on the samples from eastern coast particularly from Orissa, was carried out at an internationally reputed laboratory by a large private operator and the plant was set up. This consisted of a combination of crushing-grinding-de-sliming-classification followed by concentration in multi stage spiral concentrators and shaking table. The plant was commissioned and operated successfully. Soon a state owned company followed suit on the basis of test work carried out in a well equipped Indian laboratory. The plant worked satisfactorily after some initial teething trouble and the company plans to double the existing plant capacity by installing balancing facilities. This development prompted a number of operators, including industry leaders to join the fray and the chrome ore processing industry flourished in India. More and more operators are now in the process of adding capacities to their existing plants. This paper attempts to chart the evolution of chrome ore beneficiation industry in India through a case study with reference to an existing plant. The process technology adopted and modified to suit the altered requirements as well as the future trends are outlined.

Jan 1, 2014

By A. Pirson, J. Souza, A. Araujo, M. Barbosa, F. Guimarães, J. Lima

"Although a large number of processes have been developed and applied to the separation of barite from other minerals, there is a lack of information in the literature about the separation of barite from iron ores. Nowadays, there are millions of tonnes of iron ore disposed as a waste or tailings given its high content of sulphur in the form of barite. In order to effectively separate barite from iron ore and ensure that mining business is truly creating economic and sustainable values, this paper provides a greater understanding of barite properties, the origin and occurrence of this barium-bearing mineral, and the employed beneficiation processes. A test work is conducted in a barite bearing iron ore from a deposit located in the Republika Srpska (Bosnia and Herzegovina) in order to separate the barite and check if a marketable by-product can be produced by drawing upon rich barite tailings. INTRODUCTION The exploration of iron ore containing barite results in a large amount of unrecovered material. The main difficulty in processing and using barite bearing iron ores is given by their high content of sulphur, silica and barium, which are unwanted chemical compounds in the subsequent processes in iron industry. As a result, millions of tonnes of iron ore are discarded every year into tailings or as a waste, which results in production losses, higher operation costs and environmental impacts (Praes et al. 2013). Therefore, the separation of barite from iron ores not only means reducing the environmental impact, but also an opportunity to generate income and beneficiate society. The beneficiation of barite bearing iron ores is a subject which requires a deeper investigation to solve the challenges faced by the iron industry. There are only a few studies that describe flowsheets proposed for the production of barite concentrate of iron ores. The most likely reason for this gap is that barite is frequently exploited commercially as a primary product rather than a by-product. In order to effectively separate barite from iron ore and ensure that mining business is truly creating economic and sustainable values, this paper provides a greater understanding of barite properties, the origin and occurrence of this barium-bearing mineral, and the employed beneficiation processes. A test work is conducted in a barite bearing iron ore from a deposit located in the Republika Srpska (Bosnia and Herzegovina) in order to separate the barite and verify if a marketable by-product can be produced by drawing upon rich barite tailings."

Jan 1, 2018

By O. Kökkilic

This study covers the tests to develop separation process for production of clay and colemanite rich concentrates, and aims to serve the clay and colemanite concentrates extracted from the tailing dams to the industrial applications. For this purpose, samples from the tailing dams in Kestelek Boron Plant (Turkey) with an average B2O3 content of 8%~11 % were subjected to the investigations. The separation process of hydrocyclone--to make clear the way to obtain either clean clay or cole-manite--was initially discussed. Therefore, following the gentle scrubbing (to keep the bimodal size distribution between clay and colemanite) of the tailings to disperse the slurry, two alternative multistage hydrocyclone processes; allowing to recycling the overflows or underflows to concentrate clay and colemanite were respectively tested. As a result of the preliminary tests, the multistage hydrocyclone separation in direction to the clean colemanite concentrates (recycling the underflows) gave the better separation efficiencies. So, all the parameters such as apex and vortex finder diameters and feeding pressures were examined with the multistage hydrocyclone process allowing the recycling the underflows. The detailed multistage hydrocyclone separation process of the tailing dam wastes yielded with colemanite concentrates (approx. 12 % of the feed, w/w) with B2O3 content of 35.0 % and the clay concentrates (approx. 42 % of the feed, w/w) with B2O3 content of 2.1 %. Colemanite concentrates were found good enough either to re-feed in to the separation process or to keep upgrading for final product ready to use in Industry whereas the attempts on production of light bricks from clay concentrates has failed. But it is worth to point out that these clay concentrates can be used for agricultural purposes just in the form as it is.

Jan 1, 2014

By S. Vimalnath

The bioremediation capability of Pseudomonas aeruginosa cells was investigated for the biosorption of lead ions from aqueous solution. The various parameters such as pH, kinetics, biomass loading and concentration of lead affecting the biosorption process were studied. Complete bio removal of lead could be achieved for an initial concentration of 12.4 mg/L at pH 6.2, corresponding to typical industrial effluents. The biosorption isotherm followed Langmuirian behavior and the Gibbs free energy (?G) was determined to be-30.8 kJ/mole, indicative of chemisorption between the functional groups of the bacterial surface and lead. The biosorption kinetics adhered to a pseudo-second order model. The possible mechanisms of interaction of lead with the bacterial cells are discussed. A carbon paste electrode with a coating of biomass was developed for lead ion detection in aqueous solution using cyclic voltammetric technique. Concentrations of lead up to 5x10-5 M could be successfully detected using cyclic voltammetry, which could be improved to a detection limit of 1x10-8 M adopting differential pulse anodic stripping voltammetry (DPASV). Keywords: Pseudomonas aeruginosa, bioremediation, lead, voltammetry

Sep 1, 2012

By B. P. von der Heyden, P. Neethling, M. Tadieb, L. Babedi

The effects of trace element substitutions in sphalerite mineral structure on optimised floatation response have, as yet, not been fully constrained or fully understood. To further this important field of study, this contribution focusses specifically on mineral and surface chemistry, and electro-chemistry of Cd- and Co- substituted synthetic sphalerites using Raman spectroscopy and Zeta potential experimentation. Raman spectroscopy illustrates that the presence of these impurities results in the introduction of a new mode, the relative intensity of which can be correlated (Cd r2=0.95 and Co r2= 0.99) to the dopant concentration. Comparison to X-ray Diffraction results measuring the unit cell parameter further shows that this relative intensity (Cd r2=0.81 and Co r2= 0.99) may provide insights into the degree of lattice strain within the mineral structure. The zeta potential distribution of an un-activated Cd-sphalerite show no detrimental effect as function of Cd content. Although the iso-electric point shifted from 2.45 at 1 wt.% Cd to 2.69 at 3.68 wt.% Cd, the zeta potential remained negative at alkaline media. Conversely, cobalt at low concentration of 0.36 wt.% had a detrimental effect on the surface charge, resulting to a close to neutral zeta potential at different pH. The adsorption of Cu ions on the surface of Co-bearing sphalerite conditioned in an alkaline media slightly increases the zeta potential of Co-sphalerite. While the Cd-bearing sphalerite decrease in negative zeta potential at >1 wt.% Cd indicating a complete exchange between Cu and Zn. The results presented herein illustrate that, based on the chemical nature of the substituting metal; sphalerite will exhibit multiple response to flotation reagents. Maximum recovery of zinc can thus only be achieved through multidisciplinary study and fundamental understanding of the effects of cation substitution on mineral structure and surface chemistry, the latter necessarily affecting the floatation response.

Jan 1, 2018

By E. Burdukova

This paper explores the relationship between the rheological behaviour and mineralogical nature of three different natural ore types. Rheological measurements performed here on Platreef, Kimber-lite and Norseman-Wiluna ores are correlated with the variation of phylosilicate mineral content in these ores and the corresponding physical properties of selected phylosilicate mineral groups. Preliminary results show that the clay mineral group (talc) has the least effect on both Bingham yield stress and viscosity of the three ore slurries tested, whereas the serpentine mineral group has a dramatic increasing effect on the Bingham yield stress especially at very low solid volume fractions. The Bingham viscosity of the mineral slurry appears to be the most influenced by the presence of the swelling clay mineral group (smectite). Significant increases in either Bingham yield stress or viscosity due to elevated contents of these problematic phylosilicate mineral groups are likely to cause negative effects on the processing and manageability of mineral slurries but it is unclear which is likely to have a more detrimental effect.

Jan 1, 2014

By K. S. McClure, S. B. Chitralekha, R. B. Gopaluni, Chmylek. T., S. L. Shah

This is a tutorial paper on industrially successful approaches for nonlinear process monitoring. Online process monitoring is essential to continuous operation of plants at high efficiency. The problem of process monitoring is one where an impending but undesirable process condition has to be identified and used to alert process engineers. This problem has traditionally been solved by practicing engineers using statistical techniques that detect a change in the underlying correlation structure of process variables. For linear correlation structures, algorithms such as principal components analysis, independent component analysis and partial least squares have been proposed. However, many industrial processes exhibit nonlinear correlation structure between the process variables. In this tutorial we describe various nonlinear monitoring techniques and elaborate on two recently developed methods, namely Support Vector Machine and Local Linear Embedding. The two methods are evaluated by application on two experimental case studies, a SAG mill and a polymer extruder.

Jan 1, 2014

By Linghu Changjin

Based on the characteristics of typical marine sedimentary phosphate rock in Guizhou, Southwest China, together with the research findings made on the surface electric properties of pure collophanites taken from different areas in pure water and under the action of collectors, a pure minerals flotation test of collophanite was conducted in this research. The differences of collophanite flotation behavior and the effects of the different pH values, varieties, and dosage of collector on flotation separation of collophanite were studied. It is suggested that that in pure water, collophanite had a negative charge within a wide pH range. The electro negativity values of collophanite increased with the addition of collectors GJBW and WF-01. When GJBW and WF-01 were used as collectors, the collophanite was depressed in acid medium, but had a good flotability in basic medium.

Sep 1, 2012

By M. K. G. Vermaak

Kimberlite weathering has been a topic of ongoing research within De Beers for many years. Using kimberlite weathering as an alternative to crushing has many advantages e.g. power and reducing diamond breakage. Weathering could also possibly be used in conjunction with crushing just to weaken the material and reduce power consumption. These forces have driven current research to investigate whether kimberlite weathering could be utilised for these reasons. Weathering in this context does not refer to weathering over long period of time but rather to disintegration of the material in aqeous media in relative short time periods. Previous published work discussed that the presence of smectite renders kimberlite weatherable and that the amount of smectite determines the rate of weathering (Morkel and Vermaak, 2006). The current work investigates whether cation ex-change or the adsorption of organic species in the smectite interlayer could influence the observed weathering behaviour. The results show that cation exchange does take place in the presence of cation species and that the weathering behaviour can be drastically improved with especially Cu2+ cations. Concentration and time effects of the weathering was also investigated. Weathering tests with organic species such as ethanol, methanol, edta, pentanol, butanol, acetic acid and oxalic acid was performed. The results show that organic species does improve weathering but under these testing conditions was not as effective as cations.

Jan 1, 2014

By J. Y. ` Xie

The paper introduced bio-oxidation plants of refractory gold concentrate in China and CCGRI cultures. CCGRI cultures are composed of bacteria and archaea. Archaea Ferroplasma acidiphilum is very thick and fills whole mineral surface. It plays a more dominant role in CCGRI process. Several years of practice has proved that the operating temperature in bioreactors between 38~52?,gold recovery is almost same. Pulp concentration has been increased each year and reached to 25%.

Jan 1, 2014

By H. D. Yu

In this paper, an evaluation about the process mineralogy of the rich iron mine in Mongolia with comprehensive methods is given; this provides foundation of the comprehensive recovery of iron and cobalt in the ore. The research shows that the iron?s grade is 61.23%, Co?s grade is 0.02%, the ore is rich iron ore and its Co content also reaches border mining grade. For the ore, if want get high grade iron concentrate powder, must identify the mineral composition and the occurrence of iron and take into ac-count the recovery of Co content as associated resources. Chemical phase analysis results show that 86.35% of iron exists in magnetite, which means that the theoretical recovery ratio of iron is close to 86%. Minerals spectrum analysis confirmed that the magnetite containing a small amount of Mg, Al, and other impurities, the actual iron minerals to 70.28%, which means that theoretically iron grade iron concentrate only close to 70.28%. Based on the result of iron chemical phase analysis, by investigating the liberation of sulfide minerals and gangue, the recovery index of iron can be forecasted, when grinding fineness is 35%, 45%, 55% and 65% bellow 0.074mm,theoretical content of Fe in iron concentrate separately is 67.71%,67.88%,68.78%,and 69.43%,accordingly the theoretical recovery of Fe is 87.38%,87.05%,86.92% and 86.63%. From the perspective of process mineralogy, the forecast mineral beneficiation indicators show that the ore is easy sorting ore, iron processing operations have higher recovery rate, but wants sorting of high-grade iron ore concentrate still need appropriate grinding fineness. Furthermore, associated element Co, existing mostly in pyrite and pyrrhotite, is valuable in the ore. Pyrite and pyrrhotite have ideal liberation under grinding, so cobalt can be easily enriched in sulfide concentrate.

Jan 1, 2014

The molybdenum ores currently utilized in China are mostly molybdenum sulfide ores whereas oxidized molybdenum ores, being finely disseminated and difficult to process, have not been exploited and utilized effectively. In this article the beneficiation process of a molybdenum ore occurred in an oxidized ore zone was investigated in order to provide a new way for the development and utilization of the oxidized molybdenum ores in China. The molybdenum mineral in the ore was mainly wulfenite and the associated minerals included barite, limonite, quartz and small amount of cerusite. Limonite in the ore occurred in a crust and honeycomb-like colloidal state and composed the framework for the formation of the other minerals in the ore, which filled the pores in the framework. Wulfenite was mainly fine-grained and occurred in the fine porous crust and honeycomb-like framework. The finely disseminated ore structure made the separation and recovery of the molybdenum mineral in the ore very difficult. On the basis of the mineralogical study of the ore, experiments were conducted to compare the various mineral processing methods for the beneficiation of the ore, including single gravity concentration, single magnetic separation, single flotation, and a combination of high intensity magnetic separation and gravity concentration. The results indicated that with single gravity concentration a molybdenum concentrate containing 5.85 % Mo with a yield of 11.76 % and a Mo recovery of 43.5 % was produced. With single high intensity magnetic separation it was very hard to obtain a molybdenum concentrate product. With single flotation process a molybdenum concentrate containing 7.06 % Mo with a yield of 15.14 % and a Mo recovery of 62.63 % was produced. With a combination of high intensity magnetic separation and gravity concentration a molybdenum concentrate containing 6.46 % Mo with a yield of 11.81 % and a Mo recovery of 42.11 % was produced. In conclusion, compared to the other methods the flotation process can produce more reasonable technological and economical results and is the best process for the exploitation and utilization of the finely disseminated oxidized molybdenum ore.

Jan 1, 2014

Micro-fine disseminated molybdenite was ground in a laboratory stirred mill using steel media and zirconium media respectively. The floatability of ground molybdenite and slurry chemistry was investigated. It was found that the total recovery of ground molybdenite using zirconium media was higher while the pH and Eh of the slurry are lower than that using steel media. When steel media was used, iron oxy-hydroxides had been generated coated on the surface of molybdenite, and decreased the floatability of molybdenite, especially of the -10µm particles. The iron and lead oxy-hydroxides was generated by the reaction between steel media with pyrite and galena associated with molybdenite. It was also found that changing the grinding media to inert can benefit the flotation of molybdenite. Keywords: stirred mill, grinding environment, floatability, micro-fine disseminated molybdenite, fine grinding

Sep 1, 2012

By Ji Hoe Kwon

Hindered-settling column process has been used for the separation of mineral particles for many years. In this study, a model based on DEM (Discrete Element Method) was used to simulate the movements of particles in a settling column separation process. DEM model is capable of describing the motion of particles and calculating the impact forces between particle and particle, and particle and wall contact under various operating conditions. Drag force, rotation induced Magnus lift force, contact force and the gravitational force acting on individual particles were considered for establishing the mathematic models. The overall motion of the particles in water is satisfactorily simulated by the DEM, and the result shows good agreements with the result of lap-scale experiment.

Jan 1, 2014

By B. McFadzean, P. E. Ngoepe, P. P. Mkhonto, J. Taguta

The adsorption of heterocyclic collectors such 2-mercaptobenzothiazole (MBT), 2-mercaptobenzoxazole (MBO), 2-mercaptobenzimidazole (MBI) and their derivatives on pyrite form a basis in understanding the flotation reactivity that may be applicable in a wide range of sulphide minerals. This study uses a computational and experimental approach to determine the heat of adsorption of MBT, MBO, MBI and modified MBT collectors onto pyrite surfaces. Computational calculations found that the adsorption energies were in the order: MBO > MBI > MBT. The heterocyclic collectors were adsorbed in their thiolate form on the surface. In the case of the pyrite (100) surface, the MBT adsorbed through the exocyclic sulphur atom, while MBO and MBI adsorbed through the exocyclic sulphur and N atoms onto the 5-coordinated Fe atom. The (111) surface was found to be more reactive and different adsorption mechanisms were predicted, where the MBT exocyclic sulphur atom bridged on the 5- coordinated Fe and surface 2-coordinated sulphur atoms, while the N atom adsorbed on the 5-coordinated Fe atom. In the case of MBO and MBI, dissociation of the exocyclic sulphur atom from the collector occurred with subsequent interaction with the surface 5-cordinated Fe and 2-coordinated S atoms. This resulted in the collector carbon atom adsorbing on the surface 2-coordinated S atom, while the N atom adsorbed on the 5-coordinated Fe atom. The adsorption of the modified MBT was found to be more exothermic than the MBT, which showed that introduction of a –CS2 group on the exocyclic sulphur atom improved the affinity of MBT on the surface, and was thus a better flotation collector. The computational results were supported by experimental enthalpy of adsorption measurements and microflotation tests. The chemistry of the heterocyclic thioamides is complicated by the fact that they can exist in a number of tautomeric and ionic forms at different pH’s. This is discussed in relation to the flotation and calorimetric data.

Jan 1, 2018

By Luis Cáceres, Genny Leinenweber

"We have designed a planar perpendicular flow cell for electrochemical measurement of a mineral available as a fine powder. The working electrode consisting of mineral powder supported on a carbon paste surface as a 4 mm diameter disk, was concentrically positioned inside a vertical tubular reactor. The counter electrode was a 316L tube embedded in the body cell. The supportive media was a 1.2:1 mixture of candle wax and graphite powder respectively, which is a good electrical conductor. The concentrate electrode as a film attached on a carbon paste disk was prepared rubbing the surface carbon paste against dried powdered mineral. An Ag/AgCl 1 M KCl cell as a reference electrode was attached to the body cell by using a fast coupling fitting. A stable flow rate was achieved using a frequency inverter to drive the pump motor. The flow through the cell verified to be laminar due to the Reynolds number in the cell flow passage. Cyclic voltammetry from - 1200 a 600 mVSAgE were measured using a carbon paste with and without mineral attached to the surface. The main findings of this work were: a). Electrochemical measurement of mineral powder in contact with flowing samples was easily achieved using ground mineral. This is important where massive samples are not available. b). The voltammetric curve features of ground mineral coincided with reported data. c). The working electrode could be quickly replaced while maintaining very good reproducibility."

Jan 1, 2014