Search Documents

By J. Faitli

The Lake Balaton is the biggest and for many reasons the most important lake in Hungary. To preserve its healthy nature it is necessary to remove the accumulated mud time to time, similarly to the many living waters, lakes and rivers everywhere. Typical existing technologies (mechanical, hydraulic) require large depositional areas, where the removed slurry and mud is dewatered through very long time. One problem is the non existence of an economical mud thickening technology. Another major problem is that current methods remove the sand fraction with the mud as well. Many times sand has to be complemented from outer sources to endanger the natural balance of the living water. By the financial support of the NKFP 3A/068/2004 Hungarian Research Project our consortium has been looking for the solution to the above mentioned problems. The original ideas of the project were: 1. Sand should be separated and returned to the water by hydrocyclon; 2. New mud thickener should be developed based on the principle that vibrating rods can force settling and packing of mud particles. The work was started by fundamental research with different samples from Lake Balaton and River Bodrog. An automated settling column (45L) has been built for the investigation of the effect of vibrating rods on the settling behavior of suspensions. An optical sensor has been developed by with the settling curve (height of settling slurry as function of time) can be automatically measured. Different vibrating methods and parameters have been tested by the application of a linear motor and mechanical eccentric drive. On the basis of the fundamental research a new thickener, called the rod ? lamella thickener has been developed and an industrial size (50m3/h) mud removing technology has been built. Main parts of the technology are the traditional dredging barge and the thickening technology. The thickening and sand separation technology is tugged by the dredging ship. Its main elements are the homogenization tank, slurry pump, hydrocyclon and the rod ? lamella thickener. In this unit lamellas carry out pre-thickening, then vibrating rods further increase the concentration. The thickened mud is transported out by a screw - of which revolution number is precisely controlled - against a spring supported valve. Paper reports about the design, building, water probe and on-site tests of this mud removing technology. Two new patents had been presented, one is about the rod ? lamella thickener and the other is about the mud removing technology with sand separation.

Jan 1, 2014

By Peter Kondos

The need for a sustainable development of ore deposits makes it imperative to be innovative and mindful in creating an economically and environmentally viable operation, while maintaining a good working relationship with the various stakeholders involved in developing and operating a large and complex mining project. This is becoming immensely important as gold ore deposits are becoming more mineralogically complex along with lower grades presenting both metallurgical and environmental challenges that need to be addressed in mitigating risks and improving project economics. This paper presents Barrick?s approach to development of strategic technologies for our long-term sustainable growth through conversion of valuable resources into reserves for both our green-field development projects and the expansion of our existing mining operations. Some of the key strategic solutions, including mineral processing, metallurgical and energy technologies, developed by Barrick and their impact on some of our complex gold and copper-gold ores will also be discussed in this paper. Keywords: gold ores, copper-gold ores, processing, breakthrough technologies

Sep 1, 2012

By X. Y. Liu

A culture-independent approach based on 16S rRNA gene clone library was used to analyze the bacterial community change both associated to the solids and in the liquid phase during pyrite bioleaching process. Phylogenetic analyses of 16S rRNA fragments revealed that the retrieved se-quences mainly related to genus Leptospirillum, genus Sulfobacillus and genus Acidithiobacillus. During the bioleaching process, genus Leptospirillum trends to grow associated to the solids while major of genus Sulfobacillus were in the liquid fase, only accounting little portion in the solids. Genus Acidithiobacillus can grow both on the solids and in the liquid phase, but accounting high portion on the solids.

Jan 1, 2014

By Y. X. Yang

Porous silica was obtained by acid leaching of chrysotile. The porous silica had been characterized by chemical analysis, powder X-ray diffraction (XRD), Fourier transform infrared spectros-copy (FT-IR), and N2 adsorption-desorption techniques. It is shown in this study that the porous silica retains the nanofibrous morphology of the original chrysotile, and produces a high specific surface area (SBET) of 391. 8 m2/g and total pore volume of 1. 05 mL/g. The increase in SBET and the total pore volume of the porous silica reflect the formation of micropores of 1.2~1.5nm and meso-pores of 3.2~3.8nm in diameter inside the porous structure. The hysteresis loop of N2 adsorption-desorption curve indicates mainly slit-shaped pores. The porous silica is amorphous, but its structure is regular to some extent. The structural unit of silica from chrysotile is a SiO4 tetrahedron and six-member silicon-oxygen rings with the tetrahedral positioned alternately up and down in the six-member rings.

Jan 1, 2014

By B. Q. By

TiO2 is an ideal material for catalytic technology due to its unique properties. In this paper, Sm3+ doped TiO2 photo-catalyst was developed to improve the efficiency of TiO2 and to use the natural light as irradiation source, which was made from Titanium Tetrabutoxide and Samarium Oxide with the Sol-Gel process. The Sm3+-TiO2 photocatalyst was used to degrade reactive orange 4 (RO4) in Azo Dyes. The effects of solution pH, Sm3+ concentration and catalytic time on the degradation rate of RO4 were studied. The characteristics of the catalyst were analyzed with XRD and TEM. The experimental results show that the catalyst has high activity in the degradation of RO4. The Azo bonds of RO4 are active and easily broken by oxidation. The catalytic activity of the Sm3+ doped catalyst greatly depends on the pH of solution. The catalyst has high photo-catalytic activity at both neutral and alkaline conditions. The degradation mechanism of the Sm3+ doped TiO2 photo-catalyst was also discussed.

Jan 1, 2014

By Z. G. Song

As a kind of complex physicochemical process, grinding would affect the subsequent mineral processing such as flotation considerably. In this study, the effect of wet grinding on malachite and calcite flotation using sodium oleate as collector was studied. And the mechanism of the effect of grinding was investigated. Laboratory scale grinding and flotation testing of malachite and calcite samples were performed. Different grinding media were used, including steel balls and zirconia balls. It was the aim of this work to study the effect of grinding on the pulp chemistry paying particular attention to flotation recovery. The effect of grinding media and different addition location of sodium oleate on malachite and calcite flotation was studied. The methodology used in this project involved grinding the ore with and without the addition of sodium oleate in mill, measuring the pH and metal ions produced by minerals after grinding, adding various quantities of sodium oleate and determining the copper recovery. The presence of species of products on the minerals after grinding was probed using X-ray photoelectron spectroscopy (XPS), and the metal ions produced by minerals after grinding were measured by atomic absorption spectrometry (AAS). It is showed that the mil-ling environments evaluated significantly affected the flotation of malachite and calcite. This study also discusses the effecting mechanism of grinding environment on floatability of malachite and calcite.

Jan 1, 2014

By E. V. Zelinskaya, V. U. Starostina

"The Irkutsk region is a raw material region. There are a lot of big enterprises for extraction and processing of oil, gas, coal, iron, gold and rock salt. Besides of it, refractory clays, limestone, mica, gypsum and talc are mined in the region. The most important type of mineral raw material is a gold. More than 8.5% of the total mining in the Russian Federation is extracted in Irkutsk region. It is about 0.7% of the world production. The environmental problems of mining and processing enterprises are a complex set of issues that requires of the searching of effective methods to be solved. One of the key environmental problems remains the reduction of waste generation and the introduction of environmentally safe waste management. After analysing different methods of environmental impact assessment it is established that the method of Life Cycle Assessment is one of the most effective methods for mining production. This method base? on the material balance of flows of raw materials, products and waste. The method of Life Cycle Assessment allows to identify the effects of environmental pollution under the influence of mining and processing at a quantitative level and to show real quantitative forecasts of the possibility of managing the flows of raw materials and waste.INTRODUCTION The Irkutsk region is a raw material region. There are a lot of big enterprises for extraction and processing of oil, gas, coal, iron, gold and rock salt. Besides of it, refractory clays, limestone, mica, gypsum and talc are mined in the region. The most important type of mineral raw material is a gold. More than 8.5% of the total mining in the Russian Federation is extracted in Irkutsk region. It is about 0.7% of the world production. The main provider of precious metal is the Bodaibo region. This is a main location for the major ore companies such as “Vysochaishy”, which produces about 5.0 tons a gold per year; “Pervenets”(PJSC Polyus, the largest gold producer in Russia) - 4.5 tons/year, “Druza” - 0, 5 tons/year. Placer gold is extracted by more than 40 enterprises. In connection with this, there are many plans about a building of new and reconstruction of concentrating factories. Consequently, an increase in the volume of processing is expected. The main projects are the construction of a new mill of the Mining and processing plant GOK “Vysochaishy” with a capacity of 2.6 million tonnes of ore per year; the development of the “Uhakhan” gold-field - 23 km from the “Goltsa Vysochaishy” gold-field; the opening in the Bodaibo region the next parts of the gold-deposit ""Pervenets"". Additional, the growth in a gold production can be achieved by a store of gold in the “Sukhoi Log” deposi"

Jan 1, 2018

By W. Z. Yin

It is investigated systemically in this paper that the granularity of the precursor, ZnC2O4?2H2O, is influenced by synthetic conditions. Instantaneously adding of precipitation agent is able to control the mean size of precursor ZnC2O4?2H2O under 300nm, which has great function to obtain well-dispersed ZnO nanoparticles in the next step, pyrolysis. The pyrolysis kinetics model of ZnC2O4?2H2O powder is obtained. Two steps take place during the pyrolysis. The first is dehydration, which the pyrolysis kinetic model is 2(1-a)2/3(chemical reaction), A=8.3×108s-1, E=(75.82±3.00) KJ/mol. The second is formation of ZnO, which the pyrolysis kinetic model is (1-a) (random nucleation and latter growth), A=8.45×1028s-1, E=(360.54±12.00)KJ/mol. ZnO nanoparticles obtained by pyrolysis take on self-growth behavior. It is resulted that for precursor ZnC2O4?2H2O pyrolysis time takes obvious influence on the partilces size under 420?, 500? and 600?. Finally, a new flow sheet for synthesis of ZnO nanoparticles is investigated, in which blendes is used as raw material and hydrometallurgy is introduced into it. The whole flow sheet has no industrial wastes, that is all byproducts can be used in the flow sheet recycled, resulted in the de-crease of productive cost and industrial wastes.

Jan 1, 2014

By O. Jerez, A. Novoselov, L. Gutiérrez, J. Morales, U. Kelm

"In Chile, the evaluation to reprocess tailings for elements other than the traditional Cu, Mo, Au, and Ag, as well as projects to implement long-term monitoring of mining residue sites are key elements of the government’s roadmap laid out for the mining industry for the next two decades. Characterization routines for tailings and mining residues in general have to be adapted from traditional ore and gangue mineral and micro-chemical studies. This contribution summarizes key aspects for the regional mining industry for a basic characterization of tailings with emphasis on small- to medium-size operations with limited in-house facilities and funds to carry out extensive characterization programs. The oldest tailings in Chile were deposited almost a century ago; this fact gives importance to the recovery of past ore /gangue feed information, process circuits and changes (e.g. acid to alkaline flotation), process water provenance and recovery, meteorological registers, and routines of filling a tailings impoundment. Basic characterization should include X-ray fluorescence spectrometry combined with laser diffraction (LD) granulometry followed by X-ray diffraction (XRD), optical microscopy (OM) and automated mineral analysis (AMA) on a reduced set of samples identified by hierarchical cluster analysis. For this detailed stage, only coarse tailings are recommended for direct a study by microscopy and automated mineralogy (P80 >100 µm); for fine tailings (P80 ~30 µm) a combination of XRD and deposit type adapted sequential extraction are more informative options. In particular, for XRD of clay phases, losses of crystallinity may result in deviation of spectra from standard reference phases due to prolonged storage. To monitor surface alteration, scanning electron microscopy can be complemented by Raman spectroscopy to detect residual reagents on mineral surfaces. For reactivity modeling BET measurements are essential."

Jan 1, 2018

By L. W. Luo

Zeolite in some regions or countries of the world have been the subjects of materials for environmental remediation involving the use of removal to heavy metal ions and some organic pollutant as a sorbent because of its capacious ions exchange and huge surface area. This article addresses the equilibrium and kinetics for manganese adsorption using zeolite modified by hexadecyl trimethyl ammonium bromide (HTMAB) as a sorbent material over a range of pH between 3.4~7.2 with eight different Mn(?) solution concentrations. PHzpc (pH of zero point charge) of the sorbent was examined according to the method proposed by Tripathy and Kanungo, and a value of 6.91 was obtained. The experimental data fit langmuir?s model for the majority of pH and Mn(?) solution concentrations tested (0.92<R2<0.97). The maximal adsorption capacity, qm ascending with pH between 3.4~7.2, rise from 15.01mg?g-1 at 3.4 to 19.46 mg?g-1 at 7.2. Besides, the constant of Freundlich Kf have the same trend with qm, increases with pH ascending. And the sorption intensity, represented by parameter 1/n in Freundlich?s model, is favorable in entire range of metal ions concentration studied. Finally, kinetics data accurately fit to pseudo-second order which indicate that there must be sorption of Mn(?) behavior occurring on inner-sphere of the sorbent.

Jan 1, 2014

By Y. M. Zhao

The dry coal preparation technology based on air dense medium fluidized bed is an innovative dry highly efficient technology of coal by introducing fluidization technology into beneficiation.. A modularized 40-60 tones/hr system (KZX-40) with an air dense medium fluidized bed separator was established. The construction cost of the modularized system is only 1/3 of the traditional wet heavy-medium coal preparation plant construction cost with the same capacity, and the consumption of dense medium can be reduced by 50%-60%. The footprint and volume of the system are decreased by 75% and by 89.81%, respectively. These facts show the improved intensity, efficiency and economy of modularized coal preparation technique. The modularized KZX-40 system can be used to separated 50-6 mm coal over a separation density range of 1.3-2.2g/cm3 depending on the variation of <1mm fine coal content. The separation efficiency of the system was investigated at low and high separation densities by float-sink experiments. The partition curve of the products at low separation density shows that the separation density (d) is 1.33g/cm3, and the probable error (E) value is 0.05g/cm3. Using 50-6mm coal with an ash content of 55.35% as feedstock, at a high separation density of 1.61g/cm3, the clean coal with an ash content of 14.67% and the tailing with an ash content of 71.26% are produced with an E value of 0.06g/cm3. It is clear that the modularized KZX-40 system is suitable for separating 50-6mm coal effectively. During the dry coal preparation process, the dust is removed by the bag collector and recycled back into the separator. So the system has the advantages to work without environmental pollution and water. The modularized system greatly reduces the construction and operating costs and decreases the area and volume required, compared with wet dense medium system. The system is applicable to the coals located in arid regions and also to the coals that tend to slime during wet separation. Keywords: modularized, KZX-40, fluidized bed, beneficiation

Sep 1, 2012

By W. D. Guo, Y. M. Zhu, B. B. Luo

The main chemical constituents of waste cooking oil are higher fatty acid glycerides, which can be used to produce anionic fatty acids for most non-sulfide flotation. However, using the mixed fatty acids (MFA) produced by waste cooking oil as collectors directly, the flotation effect is usually not satisfactory, especially at lower temperature or room temperature. There are very rare systematic studies about the reason for poor flotation performance of waste cooking oil. This study aims to investigate the flotation and adsorption characteristic of different types of fatty acids in waste cooking oil to find out what kind of fatty acids results in the poor flotation performance. This will provide technical supports and theoretical guidance for the waste cooking oil application in the field of mineral processing. In this study, MFA were produced from the waste cooking oil, and then separated into saturated fatty acids (SFA) as well as unsaturated fatty acids (UFA), which possessing different flotation properties. The properties of the MFA, SFA and UFA were analyzed by iodine value, melting point measurement, Fourier transform infrared (FT-IR) spectroscopy and quartz micro-flotation tests. The results showed that UFA was composed of fatty acids containing group—(CH=CH—CH2)n—, having an iodine value of up to 162.90, a melting point as low as -17.3 ? and stronger low-temperature floatability. In contrast, the SFA was made up with saturated fatty acids and a few oleic acids, with an iodine value of 48.97 and a melting point of 38.8 ?. SFA had shown poor collectability and required a flotation temperature higher than 35 ?. The results of zeta potential measurements, solution chemistry calculation and FT-IR spectra revealed that both UFA and SFA can be adsorbed on the quartz surface activated by CaCl2 via the chemical and hydrogen bonding. The reason MFA having a poor flotation performance is the SFA has an extremely high melting point which affecting the dissolution of the dispersion.

Jan 1, 2018

By X. S. Yuan

With a demand for increasing energy efficiency and a need for improving bitumen recovery, a highly integrated solution for sustainable lease development of Aurora North of Syncrude has been proposed and implementation plans are underway. Flocculation and thickening technology as an important component of the integrated solution provides Syncrude an opportunity of rapid heat recovery from tailings and more flexible tailings closure and reclamation options. Flocculation of fine-particle suspensions by polymers is a non-equilibrium process whose performance is strongly influenced by physical and chemical variables. While polymeric flocculants are frequently used to establish the chemical conditions favorable for flocculation, the actual performance of a flocculation process generally depends more on the physical variables, such as the hydrodynamic conditions in mixing the flocculants and slurry. In order to study the effect of hydrodynamic conditions on flocculation of Syncrude fine tailings, a standardized laboratory test procedure called power flocculation has been developed in comparison with the conventional manual mixing methods. It is shown that the agitation speed and time in conditioning the flocculant solution and the slurry have a profound effect on the flocculation performances measured by initial settling rates, supernatant clarity and sediment density. It was found that the optimum bench test conditions for power flocculation of Aurora fine tailings with a sand-to-fine ratio (SFR) of about 1:1 are conditioning of the flocculant solution and the tailings slurry at 250 rev/min to 300 rev/min in 20 s to 40 s. The test results are inter-preted with a flocculant adsorption/redistribution kinetic model that helps understanding of the effect of hydrodynamic conditions on flocculant adsorption, floc formation and floc growth.

Jan 1, 2014

By J. Z. Yuan

The purity of rectorite is only about 70% after preliminary mineral processing, which has limited its application. In this research, different pulp densities, different dispersants, different dispersing methods and purification flow sheets were used to purify rectorite. The results show that it is possible to obtain high pure rectorite clay with the purity above 90% and concentrate yield between 24.9% and 29.4% by the purification process with composite dispersants, stirred mill grinding dispersion and so on. The obtained high pure rectorite can be further used in rectorite nanocomposites.

Jan 1, 2014

By X. H. Li, F. Xie, Q. Zhang, Z. H. Shen, S. Mao

"There is abundant rare-earth element(REE) in our country, but it is very fragmented in the earth's crust, and it is very difficult to mining or mining cost is extremely high. There are few of industrial value rare-earth deposits. There is a lot of concomitant rare-earth deposits, and the comprehensive utilization value is high. There is very rich carlin-type gold resource, associated with a certain amount of REE in the southwest of Guizhou province. In order toutilize comprehensively the resources, this paper conducts the study on the occurrence characteristics of REE in the ore. By the chemical analysis, the gold grade is 3.35g/t, the organic carbon 0.81%, the total REE 0.022%, which is a high carbon fine disseminated gold ore. By the optical microscope and XRD analysis, the major minerals are quartz, pyrite, calcite, limonite, arsenopyrite, mica, kaolinite, clay minerals, etc. In addition, there is a large amount of carbonaceous materials, such as organic carbon, graphite, which is harmful on leaching of gold. By the scanning electron microscopy analysis, there are thorium, lanthanum and neodymium, ytterbium, persimmon and other REE in the ore. Gravity separation shows that REE could be enriched to lighter material mainly, which indicates that REE disseminate closely with lighter materials.INTRODUCTION Carlin-type gold ore is important gold resource in the world, which are mainly distributed in Nevada and its vicinity, as well as the two Golden Triangle of Yunnan, Guizhou, Guangxi and Sichuan, Shanxi, Gansu province in China(Su W.C. et al.,2009; Xia G.X.,1996).Guizhou carlin-type gold ore is the second largest gold resource in the world(Muntean J L et al.,2011), distributing along the southwestern margin of the Yangtze plate, mainly mineralizing in the neopaleozoic-early mesozoic(Xie Z J et al.,2017). Many large gold deposits have been found in southwest in Guizhou in twentieth century, such as Zimuyou,Getang, Lannigou, Shuiyindong and Laowanchang gold deposit, and so on, and the gold reserves reach over 100 tons(Xia Y. et al.,2009).There is a certain amount of rare-earth resource in the carlin-type gold ore in the southwest in Guizhou province, and the current researches might mainly focus on characteristics of REE from the angle of geological mineralization(AnanyevY.,2015), not from the angle of separation and enrichment."

Jan 1, 2018

By H. R. Manouchehri

"In all electrical beneficiation methods, the difference in electro-physical properties of the contributed mineral particles, essentially frictional charge, electrical conductivity and dielectric constant properties are exploited to achieve separation. The composition of the raw material determines what kind of either corona charging, conductive induction, or triboelectric separation method should be employed. The process is versatile and is influenced by different parameters related to mineral characteristics, surrounding ambient conditions and electrical and mechanical attributions of the separating device. Electrical separation is surface based beneficiation method which is mainly affected by the surface and surface changes of the minerals. Therefore, it is essential to understand how the electrophysical properties of the minerals can be changed/modified. During electrical/electrostatic separation process, both charge magnitude and its polarity that developed on the particles and therefore, their electrical beneficiation potential is essentially defined by surface phenomena. Therefore, it is essential to understand how the main electro-physical parameters can be changed/modified with applied surface treatment/pretreatment methods to promote separation. Surface treatment of minerals is carried out by different means, including chemical conditioning, irradiation, thermal treatment, etc. This paper discusses and analyze the electrical separation process, electrophysical properties of the minerals with special focus on the effect of surface pretreatment/treatment methods to affect electrical beneficiation potential of the minerals. The surface treatment methods vary in a wide range from simple surface cleaning to more complicated chemical conditioning and doping. The knowledge of the solid-state physics and chemistry leads to improve the beneficiation potential of different mineral systems by choosing suitable treatment method(s). Despite the complexity and multiplicity of the charging mechanisms, difficulties in separating fines it seems to be beneficial make our attempts to further investigate and develop the process as dry, low cost beneficiation process, especially nowadays when environmental concerns, as well as energy and water consumptions are main concerns for mining industry."

Jan 1, 2018

By G. X. Du

Improving reaction effectiveness of asbestos tailings and acid is main means to increase the productivity of magnesium hydroxide and amorphous silica and to reduce production costs. In this paper, the process optimization of acid-leaching reaction process of asbestos tailings is reported. Through the orthogonal experiments of four influence factors, such as acid consumption, reaction temperature, reaction time and initial acid concentration in the leaching reaction. The experiment results indicated that the optimal process parameters were as follows: reaction temperature was 95?, reaction time was 1.5h, acid consumption was 218.9g hydrochloric acid(37%) per 100g asbestos tailings and initial acid concentration was about 25%. The influence significance sequence of the four factors was as follows: reaction temperature > reaction time > mass concentration of hydrochloric acid > hydrochloric acid consumption. Under the optimum process conditions, the leaching rate of MgO was 97.3%, total iron 98.15% and Al2O3 57.9%.

Jan 1, 2014

By E. Hulthén

Cone crushers are used in the mineral, mining, and aggregate industry for fragmentation of rock materials. Control systems for cone crusher settings are widely used to compensate for wear and to protect the machines. The eccentric speed in a cone crusher affects the number of compressions the material is exposed to and thus the particle size distribution of the product. Eccentric speed also affects crusher capacity. However, the speed of the crusher is mostly fixed, because speed changes must be made by shifting pulleys, a process which is quite time-consuming. By applying a frequency converter, which has decreased in cost during recent years, it has become possible to adjust the speed continuously. By also applying mass-flow sensors to the process, the crusher can be run optimally to yield the most sellable products in a given moment. Existing systems normally only protect the machine. The sensors can be mass-flow meters, e.g., conveyor-belt scales. To analyze data from the process and calculate the appropriate value for the speed, an algorithm has been developed. The developed algorithm was tested and evolved at a crushing plant for aggregates that produces around 350 kton a year. The algorithm was implemented in a computer that could communicate with the frequency controller, retrieve data from four mass-flow meters, and also interact with the opera-tor. The computer was reachable over the Internet for the researchers at Chalmers and the algorithm was tuned and improved on-line. The result is a crushing stage that consistently and maximally produces the most desirable product. The performance (yield of required products) increased by 4%. As a bonus, the lifetime of the mantles increased 27% on the evaluated crusher.

Jan 1, 2014

By Imre Gombköto, Zoltán Pap, Ákos Debreczeni, Sándor Nagy

Eddy current separators have become generally used in waste recycling industry during the last decade. There are many papers dealing with separation processes on eddy current separators, and also many article describes particle trajectory and different particle features affecting particle trajectory. These data are used in modeling as well. Within the frame of R&D project called ‚Fundamental research into the exploitation of the economic development potentials of critical raw materials in international co-operation - CriticEl?, authors are aimed for using Eddy Current Separator (ECS) as a mechanical separation step of high value critical elements recovery of selected WEEE’s like display panels, PCB’s. ECS, equipped with 305 mm wide belt, and a concentric magnetic rotor is used for experiments targeted development of methodology for determining separability of different particles on ECS. The subject of our work was to investigate the behavior of model particles with different shape, conductivity (aluminum and copper), orientation and size in order to separate Al and Cu according to the results of many experiments were carried out in this field. However it looks like that throwing distance of one particle is only possible to describe by a certain distribution for even the same particle within the frame of the same conditions. Sample mean and standard deviation are depending on some of the particle feature and acting forces. The paper is going to draft the first results on the relationship between distribution of throwing distance and particle properties.

Jan 1, 2014

By Fangming Liu

The key problems of current flowsheets and equipments are analyzed. A new steel slag&apos;s crushing flowsheet whose key equipments are the improved inertia cone crusher and inertia vibrating jaw crusher is proposed. An advanced two stage open-circuit crushing method is adopted in the flowsheet, with 90% of particle size crushing under 6mm. Using inertia vibrating technology and selective crushing principle the crushers can realize steel slag separating fully into steel and slag and with flexible transmission mechanism the crusher can be protected when iron lump is passing. The flowsheets can enhance the recovery of metal greatly, and expand the application range of tail slag and added value.

Sep 1, 2012