Search Documents

By Komar Kawatra, Joseph Halt

"Bentonite clay has been the traditional binder for iron ore pellets. However, bentonite increases pellets’ silica contents and is expensive. Researchers have proposed lowering bentonite doses by mixing it with other common binders. These mixtures may only be successful if the fundamental bonding mechanisms are understood. For example, what happens when bentonite (physical bonding) is mixed with fly-ash (chemical bonding)? What happens when bentonite is mixed with cornstarch (physical bonding)? In this paper, experiments are described where bentonite was mixed with various ratios of cornstarch and fly-ash, and pellets were agglomerated using 0.66 % w/w binder. Ca(OH)2 and CaCl2 were added as activator and accelerator, respectively, to the bentonite-fly ash mixture. Curves of pellet dry strength vs. bentonite-starch ratio were linear, suggesting the physical-physical bonding mechanisms were compatible - acceptable strengths (> 22 N) were produced at all bentonite-to-starch ratios. This was contrary to bentonite-fly ash mixtures, which displayed dry strength curves with a noticeable minimum due to competing binding mechanisms. Bentonite alone and fly ash alone produced acceptable strengths (> 22 N), but their mixtures resulted in weak pellets. Due to the positive results using cornstarch (CS) binders, the effects of CS solubility in water were investigated using two CS with high and low solubility (60 and 7.5 %). CS was premixed with bentonite at various ratios (0, 20, 40, 60, 80, 100 %). Pellets were agglomerated using 0.66 % w/w binder. The dry strength of pellets ranged from 50-300 N using the high solubility CS mixtures, and from 50-85 N using the low solubility CS mixtures. Fired strengths exceeded 2200 N/pellet at all bentonite-cornstarch ratios. This research showed that cornstarch solubility is an important factor in determining its effectiveness as a binder for iron ore concentrates, but significant work is still necessary before it can be used as a bentonite replacement."

Jan 1, 2014

By Luís Marcelo Tavares, Daniel Francioli, Malcolm Powell, Mohsen Yahyaei

"Mathematical modeling of the comminution process requires understanding of all breakage mechanisms occurring in this mechanical environment. Modeling of high energy impact breakage is well established, however, modeling low energy breakage including incremental damage breakage, attrition and abrasion is still under development. Free fall incremental impact tests were carried out to investigate the surface fragmentation of a copper-gold ore. This process was achieved by dropping particles individually from a height of four meters onto a metallic plate. The impact specific energy was 0.01KWh/t. The setting of the metallic plate was changed to test the impact angles of 0°, 45°, and 60°. Tests were carried out using fresh angular rocks as well as smoothed particles. Changes to the plate angle and particle shape enabled the study of the influence of the tangential component of the impact energy along with particle shape on superficial breakage. By studying the fractional mass loss variation in each impact, two distinct stages of surface fragmentation were clearly determined: high fractional mass loss dominated in the first 10 impacts and was attributed to chipping, whereas low fractional mass loss occurred for the remainder of the impacts and was attributed to abrasion. Smoothed particles demonstrated higher resistantance to breakage and their surface fragmentation behavior indicated a closer relationship to abrasion, especially when lower impact angles were used."

Jan 1, 2014

By Michael Young, Rodrigo Araya, Cesar Gomez, Le Huynh, James Finch

The performance of flotation machines is closely related to the gas dispersion characteristics achieved in their operation. It is known that frothers play a major role not only in the size distribution of the generated bubble population, but also on the swarm rise velocity. A program to characterize frother effects on two-phase hydrodynamics (air-water) of Jameson cells was undertaken in a fully instrumented pilot unit installed at McGill University. Gas dispersion parameters (gas velocity, gas holdup and bubble size distributions) of the gas-liquid mixture generated in the downcomer were measured after its release into the separation chamber. The unit was operated under different conditions including gas velocity, liquid jet velocity and frother concentration (MIBC). Bubble size distributions for concentrations above the critical coalescence concentration (CCC) were narrow with Sauter mean diameter between 0.6 to 1.3 mm. The bubble size followed the general trend as encountered in other types of flotation machines, i.e., rapid decrease with increasing frother concentrations below 10 µL/L, and almost no change in size for concentrations above 30 µL/L. The CCC was between 10 and 15 µL/L. Strong correlations were found between bubble size and air-to-liquid flow ratio (APR), and between the bulk density of the aerated solution in the separation tank and the vacuum inside the downcomer. An equation is proposed to estimate gas holdup in the separation tank from vacuum and bulk density readings.

Jan 1, 2014

By Majid Saghaeian, Rasool Hejazi, Parisa Ghobadi

"Pulp handling in mineral processing circuits is very complicated due to its inherent different specifications compared with other fluids such as water. Because any variation in ore property (e.g. size and abrasion index) and pulp specification (e.g. density, solid content and pressure) causes problem in this part and reduces the plant availability and throughput as a result. The most common issues in the hose system are sumps and pipe-line blockage, wearing of the pumps impeller and liner, and pipe tearing specially at elbows and bends. High pressure grinding roll (HPGR) is employed in a closed circuit with a screen as the first stage of grinding in Zarand Iranian Steel Complex (ZISCO). Wearing of the pump and pipeline transferring the screen undersize stream was the main problem from the plant commissioning. The plant couldn't achieve to the design capacity because of this defect. Although various practical solutions such as improving the pipes and impeller material quality and eliminating the elbows, as much as possible, were done in order to downtime minimizing, but damages didn’t vanish. Since HPGR discharge contains somewhat rough and abrasive particles, the mentioned modifications didn't effective very much. Therefore, converting of the wet screen to dry and using of belt conveyor to the screen undersize handling was employed based on the plant capability evaluation and experimental and pilot trial results. Although this reformation imposed another additional cost (for conveyor system), but it had significant advantages such as increasing the plant availability up to 96%, reducing the operating costs of the wear parts, providing more stable operating condition for the HPGR performance and decreasing abrasion rate of the HPGR rolls liner because of the lower moist feed."

Jan 1, 2014

By Claudio Bisso, Javier Vargas, Charles Lozano

"This paper summarizes the activities performed to predict SAG milling throughput at Minera Esperanza. Having highly reliable geometallurgical models aided by the new computer tools and specific metallurgical testing to rely on has become a major issue in recent times due to their impact on the business. Minera Esperanza’s SAG throughput model was constructed by characterizing the ore feed and operational parameters of the plant. Producing a robust model required satisfying number of requirements for the parameters used for both the ore and the plant as follow: 1) geologic and geometallurgical characterization parameters; and 2) parameters of a plant running at the rated production under optimum operating conditions. Obtaining these parameters required increasing the quantity of samples and metallurgical testing through drilling campaigns, mapping the drill holes and putting samples through various comminution tests while sampling all operational flows at the plant to obtain the metallurgical information for the operational parameters. The information was entered on the JKSimMet software to enable a throughput model to be developed to output SAG mill throughput predictions that are very close to actual throughput figures, i.e., accurate within a range of 2% on a monthly basis."

Jan 1, 2014

By Vladimir Vigdergauz, Sergey Kondratiev

The paper reviews the existing criteria of the formation of particle-bubble aggregates during flotation. It is shown that predictions obtained by these criteria do not completely fit to the interaction between mineral particles and air bubbles. Experimental results of the studies into the influence exerted by molecular forms of collectors on the particle-bubble interaction are reported. Rate of dry spot expansion on the surface of pyrite with various combinations of chemically and physically adsorbed xanthate are examined. It is shown that molecular forms of collectors accelerate the rate of dry spot expansion on the mineral surface after the local rupture of the water film between particle and air bubble. The authors come to a conclusion that the molecular forms of collectors remove water from the interlayer between mineral particle and air bubble during their contact. Similarities of the proposed mechanism with the action of ion-molecular associates of fatty acids and amines are discussed. Reagents with high surface pressure and rate of spreading at the water-bubble interface are required for the effective interfacial dewatering. It is concluded that the value of surface pressure can serve as the criterion for efficiency of physically adsorbed reagents. The low surface pressure indicates weak collecting ability but high selectivity of the collector. Therefore, the presence of the molecular forms of collectors in the sorption layer is the necessary condition for formation of particle-bubble aggregates, and comparison of the surface tensions of collectors could be recommended as the estimation criterion of their flotation activity and selectivity.

Jan 1, 2014

By Roberto C. G. Oliveira, Scott C. Brown, Brij M. Moudgil

The wettability or surface energy of particle surfaces dictates a number of multiphase ensemble interactions that have a significant impact in mineral processing. Dispersion, bulk powder handling and flotation behavior are just a few of the parameters that are largely due to the degree of hydrophillicity or hydrophobicity on particulate surfaces. Because of the inherent impact of surface wettability in nearly all industries, fields, and multi-phase interactions, a number of simple, precise and accurate techniques for accessing surface wettability or contact angle on macroscopic flat surfaces have been developed. However, these techniques cannot be directly applied to the particulate surfaces that are often in query. Though a number of techniques are available for accessing the wettability of particulate surfaces, these methods are either relative, application specific or prohibitively tedious. In this study, key features of existing techniques are combined to formulate an improved method to delineate particle wettability that is simple, versatile and capable of providing reproducible measurements in an industrial environment.

Jan 1, 2003

By Rod Hocking, Nenad Djordjevic, Randolph A. Pax

"Semi Autogenous (SAG) mills exhibit complex interactions between the competing processes occurring inside them. Traditional practice is to measure the operation of the SAG mill at an operating point in terms of its load, power draw, steel load, ore throughput rate, water addition rate and more recently the feed size distribution. However significant departures from standard operating conditions can occur due to changes, for example, in ore hardness, the quest for higher throughputs and mill internal geometry.Fundamental to SAG mill operation are the internal processes that ensure that a given ore throughput and discharge grind size are obtained and maintained. These processes can be measured using non-contact acoustic emissions from the SAG mills which utilise the information rich noise that is generated by the grinding, flow and charge movement inside a mill. Non-contact acoustic in-mill measurements can be used for the validation of discrete element modelling (DEM). The approach being reported in this paper is to model the individual physical processes and then to simulate the assemblage of a physical mill.By modelling the assemblage of steel balls in a 1 m pilot mill and duplicating the experimental arrangement exactly with the PFC3D model, it was possible to replicate the pattern of falling balls in the experimental mill. Furthermore, the key features of the acoustic emission spectrum that was calculated compared favourably to the measured spectrum at low frequencies. The experimental spectrum is shown in Figure 1."

Jan 1, 2003

By H. Hamza, M. R. MacIver, M. Pawlik, L. Malin

"Size and shape are important properties of aggregates formed in engineering processes and natural systems. Measurement of aggregate size or shape is a challenge when the solids concentration is beyond the gel point, ?? > ??g, when the aggregates are in contact and it is difficult to distinguish or segment individual particles in the network. This paper describes the use of a micro-computed tomography (micro-CT) method for the calculation of the aggregate volume fraction, ??, and a characteristic aggregate length, ??a, based on a 3D chord length measurement algorithm. These parameters can be used to quantify changes in aggregate and pore size during a compressive yield stress test to help understand the impact of flocculation and network structure on dewatering. INTRODUCTION In a thickener, flocculation is often used as a pre-treatment step and the final solids content of the underflow depends on the network strength and permeability of the bed formed by settled aggregates (Usher, Spehar, and Scales 2009). This paper describes the measurement and analysis of micro-computed tomography (micro-CT) of flocculated mineral sediments to obtain a characteristic length, ??a, of the aggregate and pore phases during a staged compressive yield stress experiment. This parameter may be used as an indicator of changes in aggregate and pore size to quantify material behaviour in solid-liquid separation processes that depend on self-weight compression or applied pressure. This analysis was carried out to help understand the effect of flocculation on aggregate structure and the thickening process as part of a broader research on the improved solid liquid separation of tailings produced in the oil sands industry.Aggregate properties The solids phase of an aggregated or flocculated suspension will eventually settle – if left undisturbed – under the influence of gravity. As settling of a flocculated suspension continues, the solids volume concentration, ??, may increase to the gel point or gelation threshold (Landman and White 1994), ??g, above which the aggregates form a network of touching particles, or space-filling structure (Kranenburg 1994). In the sediment bed, the aggregates are surrounded by fluid and occupy a partial volume fraction, ??, according to"

Jan 1, 2018

By Francis Pitard

"The optimization of metallurgical processes requires an in-depth understanding of the heterogeneity carried by any constituent of interest. It emphasizes that knowledge of the Theory of Sampling (TOS) is the necessary step to ensure that valuable and valid research programs, pilot plants, feasibility studies, plant design and plant operations have been set on solid foundations. Too many publications today are solely based on the properties of the sample, with no mention of how this sample relates to anything in the environment where it was collected. Unfortunately sampling is an error-generating process that leaves no apparent tracks of its shortcomings. Indeed, it is easier to track down analytical errors than sampling errors. Consequently, bad sampling practices plague the scientific community and the industry and are responsible for severe money losses, unsatisfactory science and processing, and sometimes litigation. A point-by-point strategy is presented addressing sampling problems in early stages of a project. Sampling system requirements for metallurgical accounting and process control are listed. The use of Chronostatistics is suggested to determine if sampling systems are performing satisfactorily and to identify the various types of process variability that may not be easily detected by a conventional inspection of available chronological data. This strategy will help engineering firms, manufacturers, managers and supervisors to provide, install, use and maintain key sampling systems located at very important points in a process. Equipped with the appropriate sampling and statistical tools it becomes easier to minimize reconciliation problems with the mine, with suppliers and with clients. Contrary to the beliefs of many people, good sampling systems are not expensive because in the long run they help to reduce hidden cost and better regulate plant productivity; they most certainly minimize the number of unnecessary meetings looking for solutions where there are none. The suggested strategy will help specialists to extract maximum information from the available data, as large investments and crucial decisions depend on it."

Jan 1, 2014

By M. H. Moys, H. Dong

"Discrete Element Method (DEM) has become a standard tool to simulate grinding mills in order to gain information about load behaviour, power drawn, etc. However, parameters necessary to run a simulation are not always readily available. For example, the coefficient of restitution used in DEM simulation from the literature ranges from 0.1 to 0.9 due to lack of accurate values. The lack of correct input parameters results in the fact that some simulation parameters are adjusted to match the simulation prediction with the experimental results. It is inappropriate to tune one single parameter arbitrarily in order to fit the prediction with experimental results. The correct value of parameters for DEM simulation should be established, and rigorous validation on simulation results by DEM needs to be done.The objectives of the ongoing project are to measure the coefficient of restitution at conditions analogous to grinding practice. Equipment has been built to measure the coefficient of restitution. A typical case of impact test showing the vertical position of a ball as a function of time is presented in Figure 1. The coefficient of restitution between steel ball of different sizes and the targets including steel liner (e = 0.91), mild steel block (e = 0.57) and rubber liner (e = 0.7) have been measured. The coefficient of restitution reduces to 0.38-0.52 when there is a layer of coal particles (1-2 mm) on the steel liner. The effects of ball size, drop height on coefficient of restitution are investigated. Then a DEM code is developed of several contact models to simulate the impact process. This code can reveal details on velocities (translational and rotational) and forces (normal and tangential) during the brief impact interval. Figure 2 is a comparison of the rebound rotational velocity between experiment and prediction by different models. The results can be used as DEM input and to assess contact models."

Jan 1, 2003

By J. Gebhardt, D. McBride, M. Cross, S. Gilbert

Heap leaching of ores containing chalcopyrite offers a low cost option to treat low grade complex copper sulfide ore bodies. However, the slow leach kinetics of chalcopyrite at ambient conditions typically results in unacceptably low recoveries. As the mineralogy of new ore deposits becomes more complex and the effects of gangue chemistry exert a greater influence on copper sulfide leach behavior, the control of leach reaction chemistry becomes more critical. Computational fluid dynamics (CFD) technology has been useful in the capture of multi-phase interactions and provides a path to simulate complex fluid flow, gas and liquid phases, through the heap, along with species transport. Coupling the flow models with the reactive mineral dissolution, and the sometimes competing aqueous chemical and solid-liquid reactions, yields a comprehensive model of the heap leach process. The leach kinetics of chalcopyrite dissolution in heap conditions is examined, and the incorporation of chalcopyrite leach kinetics in the CFD model is described. The application of the model to investigate optimization of the heap is discussed.

Jan 1, 2014

By Arkady Senchenko

The application of centrifugal separation methods with the use of gravity concentrators has been assigned high priority while gold-containing minerals processing. The separation proceeds under centrifugal force resulted from the rotor spinning and wash water flow in the concentrators. The high specific gravity particles are retained at the trapping surface of the cone, and the low specific gravity particles are brought in the tailings. The centrifugal field in such concentrators (Knelson, Falcon) is generated by the rotating cone provoking the swirling of the free fed slurry flow. The author investigated the regularities of the separation process in the centrifugal gravity concentrator where a two-phase flow of the separated mineral media is under the pulsed pressure of the fluidization water and air. As a result of the study the possibility of the deeper penetration of the fine heavy fraction into the cone rings, providing the fluctuation of the fluidization water or air flow, was theoretically argued and experimentally proved. This allows the increase of the separation performance at low pulsation costs. The developed mathematical models are in close conformity with the actual process of interest and they enable the prediction of the heavy phase behavior at the isolated process stages in the concentrator. Keywords: gold, centrifugal gravity concentrator, containing, specific gravity, cone ring, pulsation, cost, fluidization water, Knelson centrifugal separator

Sep 1, 2012

By James A. Finch, Linda Restrepo, Mitra Mirnezami, Amy Buchanan, Maryam Hashemi

Settling rate studies on slurries from Cu/Zn flotation plants occasionally reveals two aggregation maxima at pH 8-10 and 10-12 (Figure 1). From measurements on sphalerite and silica suspensions the double maxima could be replicated. These maxima correspond to the effects of Zn and Mg ions. The aggregation mechanism of both ions is related to the formation of the corresponding hydroxide precipitate. A combination of chemical and electrostatic bridging by the hydroxides is considered to be the aggregation mechanism.

Jan 1, 2003

By Gus Van Weert, Samuel A. Bolorunduro, David B. Dreisinger

"INTRODUCTIONAcid pressure oxidation of high-grade natural acanthite was investigated in the range of 110-150°C and in the sulphate media. High acidity and low pulp density were used to prevent the precipitation of silver.RESULTS AND DISCUSSIONTwo sets of acanthite specimens were obtained from La Valenciana and Ingleterra mines, Mexico. Pressure oxidation tests were conducted on 1 litre scale in a standard 2-litre Parr titanium autoclave.EFFECT OF TEMPERATURE ON THE REACTION OF ACANTHITEThe effect of temperature on the rate of oxidation is presented in Figure 1. The rate of reaction increased with increasing temperature."

Jan 1, 2003

By Anatoly N. Vinogradov, Vyacheslav A. Tsukerman

The North-West Russia for 70 years is one the main producers of Cu, Ni, Co, Al, P, REE, Zr, Ti, Ta, Nb, Fe ores and other minerals in the Europe. The largest mining companies locates in the Murmansk region, and they extracts about 100 mln. tons of ores and damps up to 250 mln. tons of waste annually. Nevertheless an environmental situation in the region is stable due to rational management and treatment of wastes on a base of the Noosphere Concept for Nature-using suggested by Vladimir Vernadsky. The Concept was performed practically in the Fersman’ scheme of “non-waste mining and metallurgical complex”, published in the monograph “Minerals of the Kola Peninsula: current status – analyses – prognoses” (1941) and served till now as a sort of “Bible” for industry managers lightening a strategy for an industrial “trophic chain”. The recent status of this scheme is shown on the picture below, and one can see that our concept is coincide with modern ideology known as the “Industrial Ecology”. Moving along this mainstream in the Kola Peninsula since 1929, when the first mining company “Apatit” was established, we provided the water close circuit in mineral dressing plants, hydrometallurgical treatment of slag and tailings, productions of building materials and adsorbents of wastes. The innovation set of technologies designed by the Kola Science Centre allow recently to involve tailing damps in re-exploitation as the technogenic deposits of valuable raw materials for fertilizers, tanning and cleaning agents, pigments, concretes and etc.

Jan 1, 2003

By Scott C. Brown, Brij M. Moudgil, Ivan U. Vakarelski

The manipulation of the apparent hydrophobicity of particlute surfaces is necessary to achieve optimal selectivity in flotation processes. Previously a number of works have investigated the role of microscale surface and particulate morphologies on chemically modified substrates. These works have suggested that microscale surface asperities lead to an increase in flotation efficiency by assisting in the rupture of wetting films. Yet, in mineral processing the presence of surface asperities may lead to a reduction in flotation. The reason for this may-in part-be due to the presence of nanoscale irregularities at the interface. In this work, it is proposed that the presence of roughness at the nanoscale may have a dominant impact on the apparent hydrophobicity of mineral surfaces during flotation. It is suggested that as inter-asperity seperation distances are reduced capillary effects are enhanced for high energy mineral surfaces leading to the formation of liquid domains, which adversely impact hydrophobicity. In addition, as these distances approach the surfactant headgroup size obstruction of surfactant self-assembly process may occur, thereby further limiting flotation.

Jan 1, 2003

By N. T. Beukes, W. Banda

Recovery of Co from slag is a recent advancement in the extractive metallurgy of nonferrous metals. In this study a DC arc technology at laboratory scale has been applied to investigate the selective recovery of Co from slag, under three different flux types with an emphasis on influencing the activity of FeOx, SiO2 and CoO in the slag. It is known that reduction of slag by carbon is only up to a certain level after which, the recovery will depend on the chemistry of the slag, hence the need to modify the slag chemistry. Two power settings were employed to induce higher temperatures and aggressive agitation. The results were interpreted by comparing how much Co and Fe was in the slag and alloy. TiO2 reduced the amount of Fe in the product alloy compared to when CaO and CaF2 were used. The change in power did not seem to have had a major effect on the recovery although the amount of material lost to flue dust was more at a higher power rate.

Jan 1, 2003

By K. A. Natarajan

Involvement of various indigenous microorganisms in extracellular and intracellular iron oxide formation is a convincing index for iron ore biogenesis. Biomineralization of various iron oxides such as hematite, magnetite, goethite and limonite with the participation of aerobic and anaerobic microorganisms is well established. Various aerobic and anaerobic bacteria such as Gallionella, Leptothrix, Acidithiobacillus, Thermoplasmales, Pseudomonas, Bacillus spp and Shewanella putrefaciens, which are implicated in the formation of higher and lower oxides of iron have been isolated from different iron ore deposits. Diversity of microbial life in iron ore deposits can be put to beneficial use such as selective removal of undesirable constituents such as silica, alumina, clays, phosphorous and calcite and also to bring about environmental detoxification. Role of microorganisms such as Paenibacillus polymyxa, Bacillus subtilis, Yeasts and a sulfate reducing anaerobe in the biobeneficiation of hematite is illustrated. Surface chemical changes brought about by bacteria - iron ore mineral interactions are discussed with respect to hydrophobcity, adsorption isotherms, zeta potential data and bioreagents generation. Bacterial adaptation to minerals such as hematite, quartz, alumina, calcite, apatite and clays results in secretion of mineral ? specific biosurfactants such as proteins and polysaccharides. Such bioreagents can be used as selective collectors, dispersants and flocculants in iron ore beneficiation. Research results are highlighted to demonstrate silica, alumina, phosphate, calcite and clay removal from hematite. Environmental friendliness of such biobeneficiation processes is demonstrated with respect to biodegradation of toxic amine collectors, utility of ?in situ? organisms in enhancing settlement of fines in tailing dams and water harvesting. Keywords: bio-mineralization, bio-beneficiation, bio-remediation, Gallionella, Leptothrix

Sep 1, 2012

By David G. Hulbert, Daniël J. Oosthuizen, Bernard Muller, Daniël de V. van der Spuy

"OVERVIEWExpert Online is a software system that aims to mimic an informed expert on a minerals processing plant. The primary objective of Expert Online is to provide operators with effective training and on-the-job assistance. Training will mostly be done off-line (e.g. using simulators of the plant), while on-the-job assistance will help the operator during normal operation to run the plant in an effective manner. Although Expert Online focuses on the operator, it is expected to also be of value to other plant personnel, including supervisors and plant managers.Expert Online will make use of novel artificial intelligence technology (developed by MINTEK) known as the Interpreting Expert System (IES). Previously the IES was only able to explain the actions taken by the controller. Expert Online will extend this functionality to also take the process dynamics into account.Expert Online is being developed by a South African consortium comprising MINTEK (focusing on the research and development of the system as a whole), Lonmin (globally one of the biggest platinum producers, with plants suitable to test Expert Online on) and the University of Natal (academic partner, providing consultation and focusing on complex process modelling). The initial application of Expert Online will be on milling- and flotation plants.This paper discusses the structural design of Expert Online for implementation on the latest version of MINTEK’s open control platform, PlantStar, as well as several advances and additions since the previous implementations of the Interpreting Expert System."

Jan 1, 2003