Search Documents

By Amy B. Cerato, Shawn Allred, Tatiana Vargas

"Helical piles are deep foundation elements that resemble, and are installed like, a large steel soil screw — they have a slender steel shaft with one or more round helix bearing plates welded to the shaft to provide support to the structure they hold. Helical piles are rotated into the ground with a large torque motor and provide support through soil bearing on the helix bearing plates and along the shaft. The piles are available in many lengths and, due to their small footprint along with their ability to create minimal disturbance to surrounding structures, they are often used in urban settings for foundation repair, retrofitting existing buildings and for new construction projects. Helical piles are routinely installed as foundation elements in seismically active areas, such as New Zealand, Japan and the U.S.Anecdotal observations (e.g., from New Zealand, Japan and the U.S.) have shown that piles with a comparatively small cross-section and high anchoring capacity, such as helical piles, are beneficial for seismic resistance. This is presumably due to the pile’s slenderness, higher damping ratios, ductility and resistance to tipping uplift. In New Zealand, it was observed that helical pile foundations fared much better than driven and drilled concrete piles after the 2011 Christchurch earthquake. In a personal communication, Woods (2016) described that, out of the 300 structures in center city Christchurch that were supported by helical piles, fewer than 10 structures suffered significant structural damage. However, many structures supported by driven and drilled concrete piles were damaged to such an extent that they were condemned and subsequently demolished."

Jan 1, 2017

By Yu Chuang, Zai Jinmin, Liu Songyu

"The piled raft foundation is a geotechnical composite construction method, consisting of three elements, piles, raft and soils, which is applied for the foundation in an increasing number. Differential settlements have numerous negative effects on a superstructure in piled raft foundations. Through the analysis of the production mechanism of differential settlements and differential settlements control measures, a method of adjusting pile configurations is presented to control differential settlements. By comparing the measured data and finite element method analysis of one oil storage piled raft foundation, the new method is verified that the differential settlements can be reduced effectively and the inner forces of foundations are more reasonable with varying length pile configurations. The differential settlements can be minimized or even reduced to zero with right pile length.INTRODUCTIONPiled raft foundations are widely adopted for the prominent advantage of limited settlements and adequate bearing capacities. However, there always exits differential settlements in conventional piled raft foundations. The differential settlement is the main cause that produces additional stresses in the structure. Differential settlements have numerous negative effects on a superstructure as well as on a foundation, and should be restricted to allowable limits. How to control the differential settlement is the key interest.An increasing number of structures are founded on piled rafts. For this reason, design strategies that enable an optimized design have a major importance for safety and economy. An optimized design may be defined as a design achieving maximum economy of the solution, that is minimum cost for the installation of the foundation."

Jan 1, 2005

By H. Yoshida

Jet grouting was first introduced in Japan in the second half of the 1960s, approaching 50 years ago. By the end of the first 40 years, jet grouting from single to triple fluid systems had become a global technology. In the last ten years, progress in the jetting has been remarkable, and operational efficiency has improved. The quantity of carbon dioxide emitted in unit soil improvement has become one-third that of the initial technology. Meanwhile, technologies in waste recycling and horizontal jet grouting are also emerging. This paper discusses developments in the most recent ten years.

Jan 1, 2010

By Lois G. Schwarz

I did a project (Sungai Piah) as a consultant to your firm in Malaysia, where we were faced with a similar situation as sketched out in your question. The following is what we did for the grouting of the primary holes, which were both located upstream of the plug as well as downstream: We used a hydrophobic MDI based semi-rigid polyurethane prepolymer in the first phase of the grouting operation when grouting under water flow conditions. Then in the second phase and also for the contact grouting we used a two component water compatible polyurethane elastomer. And then for deeper formation grouting, when all the water flow had been stemmed in the vicinity of the plug, we used a regular (balanced stable) cement based grout. So it may not exactly answer your question, but we first used hydrophobic grout because it is very efficient to grout a formation through which water flows. We didn't stop all the leaks day-lighting downstream of the plug or all water running through the formation near the plug, but the flow of water through the rock formation adjacent to the plug was reduced by 99.9%, after completing the urethane grouting. This facilitated the placement of cement based suspension grouts without wash-out.

Feb 10, 2003

By Amr Sallam, David Thompson, Moataz Hassan

"The Little Lake Harris (LLH) Bridge was constructed in 1951 to replace the eastwest County Road 48 Bridge connecting the towns of Howey-in-the-Hills and Astatula in Lake County, Florida, United States. The 78-span bridge carries two lanes of traffic, is 3,130 feet long, and 36.1 feet wide. The concrete deck is supported by steel I-girders carried by one row of 18-inch square precast concrete driven pile. In the late 1980's, slight settlements were observed in several bents. In 1990, Florida Department of Transportation (FDOT) initiated annual survey of deck elevations during bridge inspections to monitor settlement. Due to the slow nature and magnitude of settlement, substructure instability was not a major concern to the department. However, public concern over the settlement and rough ride of the bridge continued to rise. FDOT contracted Kisinger Campo & Associates Corp. (KCA) to provide the needed design to correct the dips in the riding surface and minimize future settlement. KCA's initial design was based on the concept of ""helper bents"" at the settled bents in order to restore the bridge to original elevation. Estimated construction cost for seven helper bents was about $3.3M. FDOT requested evaluating other alternatives to reduce the cost of the bridge restoration. KCA involved the geotechnical consultant, Terracon Consultants, Inc. (Terracon), to perform a peer review and provide an economical alternative solution. Jacking and shimming the bridge was determined to be both technically viable and economical with a total cost of less than $300K. The design was completed in March 2010 and construction was completed in February 2011. This paper provides an overview of the LLH Bridge history, summarizes the evolution of the design methodology including the findings of the geotechnical study and presents lessons learned during the design and construction of the project.INTRODUCTIONThe Safety and Preservation of the State Highway System is the top priority of the FDOT. Therefore, FDOT initiated a bridge management program that starts with conducting biennial safety inspections performed by Certified Bridge Inspectors (CBI). The inspection reports together with the CBI’s recommendations are reviewed by a registered Professional Engineer (PE) and work orders are issued with priority ranking depending on the severity of the bridge deficiencies. If the scope of work is considered beyond the in-house crews’ capability, the work is then included in a contract for and bid. LLH Bridge was a little different. It was initiated in direct response to number of complaints the FDOT District 5 Structures Maintenance Office (D5SMO) received regarding settlement of the Little Lake Harris Bridge."

Jan 1, 2015

By Mohammed Faizal, Abdelmalek Bouazza

"The operation of ground source heat pumps combined with foundation piles can have an effect on the thermal behaviour of the pile and the surrounding soil. This paper presents the effects of continuous heating, continuous cooling, and alternate heating and cooling operations on ground and pile temperatures as well as the thermo-mechanical behaviour of a field scale energy pile. The effect of pile operation on the ground temperatures is highest near the pile and reduces with increasing radial distance. The results of the present studies generally showed that the thermal elasticity of the pile is not affected.INTRODUCTIONGeothermal energy piles are foundation piles used as underground heat exchangers to maintain thermal comfort in buildings, via the use of ground source heat pumps (GSHPs). Ground source heat pumps are more economical and environmental friendly compared to conventional heat pumps. Energy piles can be combined with supplemental surface heaters or coolers, known as hybrid systems, for forcefully recharging the ground during non-operational times of the GSHP. Alternative heating and cooling of the GSHP improves geothermal energy usage and alleviates heat build-up in the ground and provides a balance of ground temperatures around the heat exchanger (Jalaluddin and Miyara, 2012).The temperatures induced in the piles during GSHP operation can lead to a complex response of thermal strains and stresses in the pile concrete. An assessment of the thermo-mechanical response of energy piles for various thermal loads may assist engineers in the design process. Furthermore, an assessment of ground temperatures will also highlight any potential thermal interactions with other energy piles in actual building operations.At present, the thermal strain and stress distribution in field scale energy piles has mostly been studied for continuous operation (Laloui et al., 2006; Bourne-Webb et al., 2009; McCartney and Murphy, 2012; Akrouch et al., 2014; Mimouni, 2014; Murphy and McCartney, 2014; Murphy et al., 2014; Wang et al., 2015). These studies have contributed considerably to the understanding of the axial thermal strain and stress distributions in the piles and have shown that pile thermal behaviour is mostly thermo-elastic without inducing major structural concerns.The present paper adds to the current knowledge by assessing the pile thermo-mechanical and ground thermal response for continuous and alternating thermal loads of a field scale energy pile. The operation modes studied are 24 hours continuous cooling (Faizal et al., 2015), 24 hours continuous heating, (Wang et al., 2015) and alternate heating and cooling operation (Faizal and Bouazza, 2016). The forced ground thermal recharging is done during the non-operating times of the cooling unit, simulating a solar hybrid GSHP system for a scheduled intermittent mode of operation."

Jan 1, 1900

By Yoshinori Kurumada, Masaya Watanabe, Kenji Sasa

"The Port of Yokohama is strengthening its international competitiveness as a strategic container port in order to respond appropriately to global exchange and shipping demands. Thus, the Minami Honmoku main Pier is currently being developed. The high-standard container terminals MC-1 and MC-2 have already started their service, and the development of the container terminals MC-3 and MC-4 is currently in progress.Because the South Honmoku Pier plays an important role in waste disposal management of Yokohama, a final waste disposal site (controlled final landfill site) is being developed in Block 5 to provide long-term and stable reception of waste that will be generated in the city. For this project, a revetment with water-blocking properties and an extension approximately 1.7 km in length is being built in order to prevent water from leaking from the disposal site. The base part of the revetment will be subjected to foundation improvement using the Cement Deep Mixing (CDM) method in order to secure water shielding of the soft sediment underneath the water, prevent slipping of the seawall, reduce the amount of subsidence, and increase the foundation support force.This report presents a preliminary study on using CDM on reclaimed soil and the construction process of the development project of the disposal site in Block 5 of the Minami Honmoku Pier, which has been underway since 2007.ABOUT MINAMI HONMOKU PIERThe development of the Minami Honmoku Pier started in 1990. It was designed to develop high-standard berths with greater water depths in order to handle the increasing volume of foreign container cargo and growing size of vessels. Figure 1 shows the layout of Minami Honmoku Pier. In April 2001, the Phase 1 (MC-1 and MC-2) began services. This is the newest pier in Port of Yokohama.This pier has one of Japan’s largest terminal areas (40 ha) and is equipped with 22 row-type mega gantry cranes capable of handling the newest ultralarge container ships. The pier has a quay with a water depth of 16 m, which is the first in Japan. The pier is equipped with advanced facilities and equipment to let Port of Yokohama be internationally competitive and function as an international commercial hub. An innovative system for high-efficiency transport is currently being introduced; it includes the installation of waiting vehicle lanes and a reservation-based loading and unloading system.Since the fiscal year 2007, a new container terminal (MC-3) with a -20m deep quay capable of handling the increased size of container ships and the diversification of port logistics has been under construction and is nearly completed."

Jan 1, 2015

By Paola Campana, Maurizio Lenzi

"In the paper a non linear model for the analysis of the pile response to the axial loads is presented. The study aims to find a general analytical solution concerning the pile-soil interaction modeled by means of the method of the load transfer curves. It makes use of a criterion based on the plastic and on the hardening work locally done by the shear stresses and due to the current elastic shortening of the shaft. Then a specific solution, denoted fractal model, is found applying recurrent relations that link the shaft shear stresses and the tip normal stresses to the pile settlements. These relations are based on that one proposed by Kondner in modeling the soil samples response in the triaxial tests and then used by Chin in the inverse slope method in estimating the pile capacity by the load test results. The comparison between the model predictions and the load tests measures validate the fractal model.INTRODUCTIONThe behavior of the axially loaded piles is known to be characterized by a highly non linear trend caused by the onset of plastic and irreversible deformations in the soil starting just from the first load levels. With the purpose to reach a deeper understanding of the pile-soil interaction, the influence of the soil inelastic properties on the distribution of the axial loads and of the vertical displacements is investigated. The research starts analyzing the behavior of an infinitesimal length of a pile embedded in a non linear homogeneous soil. That initial study leads to a criterion based on the plastic and on the hardening work locally done by the shear stresses and that allows to find the axial loads as a function of the elastic shortenings of the shaft. The relation that links the pile axial load to the elastic strain of the pile material is then used. That allows to find the vertical displacements and the axial loads as function of the depth in a parametric form in which the tip settlement acts as an independent parameter. The method of the load transfer curves is used and the effects of the pile technology are included in the soil constitutive relations. The analysis is then extended to the non-homogenous soils in a very effective way. The solution is applied taking as constitutive relations of the pile-soil interface the one proposed by Kondner to analyze the soil triaxial tests and by Chin to interpolate the pile response measured in the load tests."

Jan 1, 2017

By Axel J. Pollak

Since the late 1960's the Interstate Division for Baltimore City (IDBC) has been planning and developing the Interstate Highway System for the city to meet regional planning goals. The principal goals are to provide convenient access to the central business district and the port while diverting through traffic away from these congested areas. Interstate Route 95, an eight-lane highway carrying north-south traffic, has headed the city's priority list; during the 1970's its construction proceeded steadily from both east and west towards the harbor. Closing the final 8800-ft (2670-m) gap under the harbor will complete Interstate 95's construction. This final portion, known as the Ft. McHenry Tunnel project, will be built in nine construction contracts. Construction costs of the complete project are expected to exceed $700 million, making it the costliest single project in the Interstate Highway System. Full funding is being provided initially by the Federal Highway Administration (FHWA), and the Maryland Department of Transportation will re-pay the 10 percent local share from toll receipts within the first three years of operation.

Jan 1, 1989

By Saieb Haddad, Henry Pate

"Building retaining walls in an urban area is becoming more diffi cult due to right-of-way restraints. Using standard concrete cantilever walls requires a construction easement behind the walls for installation, which for the most part is unavailable. To install these types of walls in a limited right-of-way requires extensive temporary walls to minimize the construction easement. Top-down construction walls utilizing tie-back anchors for support require either the purchase of the right-of-way or underground easements in the area of the anchors.These problems faced the Department on Interstate 75 widening in Knoxville, TN in an area of a large cut. A multi-story Insurance Building and a large commercial Retail Center were located at the top of the cut. To prevent any impact on the buildings, the walls had to be placed within a limited area. The option of buying the properties was prohibitively expensive. Due to the height of the two walls and the variability of the underling rock line, contiguous caisson pile cantilever walls were contemplated as the only wall type that would be appropriate. The cost of the two walls was estimated to be very close or even higher than the cost of purchasing the two buildings. The Department believed that there must be a better way to deal with the problem. A vertically tied-down pile frame wall constructed from the top-down with a concrete facing was developed. This allowed the construction of the walls to be restricted to the available limited area and provided substantial savings for the State. INTRODUCTIONThe widening of I-40/75 has been a major transportation project in the Knoxville area which is being constructed by the Tennessee Department of Transportation. The project includes 18 Retaining Walls and 13 Bridges. Two of the 18 Retaining Walls, refer to Figure 1, are to support two valuable properties, one being an insurance company housed in a multi-story offi ce building and the other a suburban shopping center which were appraised at $13.0 million and $5.0 million respectively. Due to the 31 ft. (9.5m) maximum height of each of the two Retaining Walls and the limited Right-of- Way of 15.0 feet (4.6m), a contiguous caisson pile cantilever wall was proposed for each of the two retaining wall sites with an estimated cost of $12.0 million each. The contiguous pile cantilever Wall is comprised of a line of caisson piles socketed into underlying competent bedrock. The design required that 4 ft. (1219mm) dia. piles be installed at 6 ft. (1.83m) centers, socketed into rock in order to provide lateral stability and restrict lateral wall movement to acceptable limits. The line of caissons would be fronted with a cast-in-place concrete face wall."

Jan 1, 2007

By Saieb Haddad, Henry Pate

"Building retaining walls in an urban area is becoming more difficult due to right-of-way restraints. Using standard concrete cantilever walls requires a construction easement behind the walls for installation, which for the most part is unavailable. To install these types of walls in a limited right-of-way requires extensive temporary walls to minimize the construction easement. Top-down construction walls utilizingtie-back anchors for support require either the purchase of the right-of-way or underground easements in the area of the anchors.These problems faced the Department on Interstate 75 widening in Knoxville, TN in an area of a large cut. A multi-story Insurance Building and a large commercial Retail Center were located at the top of the cut. To prevent any impact on the buildings, the walls had to be placed within a limited area. The option of buying the properties was prohibitively expensive. Due to the height of the two walls and the variability of the underling rock line, contiguous caisson pile cantilever walls were contemplated as the only wall type that would be appropriate. The cost of the two walls was estimated to be very close or even higher than the cost of purchasing the two buildings. The Department believed that there must be a better way to deal with the problem. A vertically tied-down pile frame wall constructed from the top-down with a concrete facing was developed. This allowed the construction of the walls to be restricted to the available limited area and provided substantial savings for the State.INTRODUCTIONThe widening of I-40/75 has been a major transportation project in the Knoxville area which is being constructed by the Tennessee Department of Transportation. The project includes 18 Retaining Walls and 13 Bridges.Two of the 18 Retaining Walls, refer to Figure 1, are to support two valuable properties, one being an insurance company housed in a multi-story office building and the other a suburban shopping center which were appraised at $13.0 million and $5.0 million respectively. Due to the 31 ft. (9.5m) maximum height of each of the two Retaining Walls and the limited Right-of- Way of 15.0 feet (4.6m), a contiguous caisson pile cantilever wall was proposed for each of the two retaining wall sites with an estimated cost of $12.0 million each. The contiguous pile cantilever Wall is comprised of a line of caisson piles socketed into underlying competent bedrock. The design required that 4 ft. (1219mm) dia. piles be installed at 6 ft. (1.83m) centers, socketed into rock in order to provide lateral stability and restrict lateral wall movement to acceptable limits. The line of caissons would be fronted with a cast-in-place concrete face wall"

Jan 1, 2007

By Aly Mohammad, Dongyi Yue

"The design of rock sockets for drilled shafts and piles proves to be a challenge for the Design Engineer. The magnitude of loads on the shaft and the behavior of the rock are critical in determining the required socket length. Several acceptable methods are available in the literature to analyze a rock socket under a combination of axial loads, lateral loads and moments. This paper will present a state-of-the-art methodology to analyze rock sockets utilizing deformation characteristics of the rock. This design methodology was implemented in the design of a major project in New York City.The project discussed herein is a marine transfer station planned for construction at East 91st Street along the East River in Manhattan. In order to support the piers and platform structures at a site with relatively shallow depth of the bedrock, rock sockets were required for the drilled shaft foundations. Rock sockets were utilized to provide the required fixity to the foundations and the structures. Acting at the top of the rock sockets are large shear forces and moments created by the lateral loads transferred from the structure.Upon review of the available techniques, a simplified method was proposed and used to analyze the rock sockets with a significant magnitude of lateral loading. The method recognizes two mechanisms through which the lateral shear and moment are transferred to the rock; a) load transfer through horizontal resistance of rock and b) the vertical shear resistance of the bond between socket and rock.The first load transfer mechanism was analyzed using the p-y curve method based on a rock model developed by Reese. The second was analyzed using a bond stiffness derived from the formula and curves utilized in the AASHTO Specifications for calculation of rock socket displacement. By comparing the two mechanisms, the main contribution to the large horizontal shear force that developed in the rock socket is identified.The paper will present a summary of the design methodology utilized in determining the length of the rock socket. It is believed that the presented method will provide substantial cost saving in selecting the most economical and efficient design length."

Jan 1, 2005

By F Debidin

The progressive rise of an H-pile during driving of an adjacent pile is described in this case history in which piles 15 to 18 m long were driven to end-bearing for the foundations for a 230 m long building. The use of a reaction beam-soil anchor system for compression load tests is discussed. The results of static load tests to determine pile capacity are compared with those obtained by the Pile Driving Analyzer and by theory. Unusual high temporary compressions were observed by field control staff. Proof testing was necessary to determine the need for restriking of some piles in which rise had occurred.

Jan 1, 2010

By A. J. Partos

Table 4, Page 311 Table 4 Experimental Parameters from Straight Line Interpretation of Mohr Failure Envelope [ ]

Jan 1, 1991

By Vivek Samu, Murthy Guddati

A new method called Effective Dispersion Analysis of Reflections (EDAR) was recently developed to effectively analyze the dispersive waves generated from lateral impact to piles. This paper presents the results of nondestructive length estimation of existing piles through EDAR. EDAR provides a new visualization method for analyzing wave reflections by transforming the response into the frequency domain thus eliminating the need to perform difficult peak picking in the time domain. In addition to being able to analyze dispersive waves, EDAR also incorporates the effects of radiation damping due to the surrounding soil leading to more accurate length estimates. Concrete filled steel tubes of different embedment depths were tested both in laboratory and field conditions. Length estimates obtained were within 10% error margins after careful analysis accounting for the presence of soil effects and effects from pile top reflection.

By Masahiko Yamaki, Takahiro Yamanashi, Hijiri Hashimoto, Hirochika Hayashi

"In this study, the authors used heat conduction analysis with the aim of quantitatively evaluating whether treating improved ground with cover soil is an effective measure for maintaining strength development in the surface layer of improved ground after constructing cement treated soil for the winter season. This report describes a simple procedure to evaluate covering soil thickness, which is necessary for the strength of the surface of cement treated soil, by using the freeze index and both the water content ratio and dry density.INTRODUCTIONIt was reported that when ground improvement using cement is performed in winter in a snowy cold region (Fig. 1 photo, Fig. 2), the uppermost 1 m of the improved ground (i.e., the cement-treated soil) tends to become prone to solidification failure from exposure to the cold air during curing (Hashimoto et al. 2006). In light of this, our research laboratory conducted unconfined compression tests using curing temperature as a parameter of analysis on improved ground toward understanding the influence of curing temperature (ambient air temperature) on the strength improvement afforded by ground improvement.The authors found that if the curing temperature is maintained at 0°C for the first 28 days after improvement and then at 5°C for the next 337 days after improvement, the improved ground is expected to have 90% of the unconfined compressive strength of improved ground whose temperature was maintained at 20°C for the first 365 days after improvement (Hashimoto et al. 2011)."

Jan 1, 2015

By Gust Van Lysebetten, Monika de Vos

The objectives of monitoring geotechnical structures can be very diverse, including optimisation of the design, quality control, long term performance assessment, and approval of innovative execution techniques. In this context, new measurement techniques, based on optical fibres, offer the possibility of accurate strain and temperature monitoring with very small sensors and limited numbers of cables. This paper briefly presents optical fibre sensing techniques and illustrates their application to geotechnical structures by means of some projects, carried out by the Belgian Building Research Institute (BBRI).

May 1, 2022

By Michael W. Driller, Wen Yan (Grace) Chen, Steven J. Friesen

"Remediation for Perris Dam has been proposed in response to deficiencies identified in a seismic stability study prepared by the California Department of Water Resources (DWR) in 2005. Lenses of potentially liquefiable soil have been identified within the dam foundation which may lose strength during a seismic event. The remediation was designed primarily to limit deformation of the dam. Nineteen construction methods were compared and evaluated for the remediation. The final decision was to use cement deep soil mixing (CDSM) to strengthen the foundation and to construct a downstream berm to stabilize the dam. The entire CDSM treatment will cover over 4,000 linear feet of the downstream toe of the dam. Over 300,000 cubic yards of CDSM will be used to strengthen the foundation. The construction of the project started in Fall 2014 and is anticipated to take approximately 3 years. This paper describes the design aspects of using CDSM to treat the foundation, including laboratory testing, investigation of overstressing/cracking, extent of treatment, effect of CDSM on pore pressures under the dam, and the results of a full-scale CDSM test section.INTRODUCTIONPerris Dam is a zoned earthfill dam with a length of 2.2 miles, a maximum height of 128 feet, and a capacity of 131,450 acre-ft of water. The dam is located in Riverside County, California at the terminus of the East Branch of the State Water Project. The embankment was constructed between 1971 and 1973 over an alluvial deposit between the Bernasconi Hills to the South and Russell Mountains to the North. A rock outcrop divides the dam into left and right reaches when viewed from the reservoir looking downstream. The embankment soil was obtained from a borrow source at the North end of the reservoir. The dam has a sloping sandy clay core (Zone 1) with a 10-foot deep cutoff trench and a silty sand shell (Zone 2) with a downstream chimney and blanket drain (Zone 3 and Zone 4) as shown in Figure 1."

Jan 1, 2015

By Schmitz Stefan, Stephan Jee-Sun

"Due to the reunion of Western and Eastern Germany in the late 80’s, a multitude of infrastructure projects had to be executed. A good portion of these projects required improvement of the motorway system. In the southern region of Leipzig, in the eastern part of Germany, it was required to connect two existing motorways. Parts of the new motorway pass old strip mining areas. These strip mining areas consist of up to 70m thick backfill material. Especially the upper 20m are very inhomogeneous soil material with a very low bearing capacity. In order to increase the bearing capacity, to decrease the differential settlements and to homogenize the soil parameters, soil improvement using sand-gravel columns was required. Bauer Spezialtiefbau GmbH executed the installation of approx. 711,000 linear meters of columns with a length from 5 m to 25 m. For the project, 11 rigs with frame leads up to 40m were used to install the 43,000 columns with a diameter of 0.8m in 27 weeks.1. INTRODUCTION1.1 Site LocationThe construction site is located in the south-eastern part of Germany, in the south west of the city Leipzig.The area to be treated had a size of approx. 500,000 m² to allow the construction of dam/embankments and a highway bridge.1.2 Required WorkIn addition to the general earthworks and the installation of geogrids and fibre mats, a total amount of more than 710,000 linm of Gravel-Sand Columns with different lengths due to the given soil conditions had to be installed:•nos. 4,206 Columns length 5m ? 21,030 linm•nos. 4,581 Columns length 10m ? 45,810 linm•nos. 10,820 Columns length 15m ? 162,300 linm•nos. 19,634 Columns length 20m ? 392,680 linm•nos. 3,574 Columns length 25m ? 89,350 linmFor the installation of the columns Gravel-Sand with the grain size of 0/32mm was used. The total amount of Material was 580,000mt"

Jan 1, 2015

By David S. Graham, Benjamin Turner, Paul J. Axtell

Seismic challenges were at the forefront of design for two parallel replacement bridge structures over the Arkansas River as part of the I-30 Crossing Project in Little Rock, Arkansas. Although not an area of the country typically associated with high seismicity, proximity to the New Madrid Fault Zone resulted in design ground motions sufficient to trigger liquefaction in alluvial channel and point bar deposits. A detailed post-award subsurface investigation program utilized CPT with complimentary borings to obtain samples for laboratory testing to assess the continuity of potentially liquefiable layers, from which we concluded that continuous zones of liquefaction across the extent of the north approach could lead to lateral spreading towards the river. An overview of the foundation and superstructure design to resist lateral spreading forces in accordance with the latest published design guidelines and research is presented. Other seismic aspects of the design are covered including timber pile ground improvement to mitigate liquefaction at the north approach embankment and foundation input motions that differ from code-based ground surface motions due to foundation stiffness, strength, and geometry. The project showcases an example of successful collaboration between geotechnical and structural designers with contractor input to address seismic challenges in the South Central US. Furthermore, the importance of considering kinematic demands on columns and other superstructure components – not just foundations – is highlighted.

Sep 8, 2021