Search Documents

By R. J. Yan

There was a plant equipped with a 32000t Hydraulic Press to be built, under which a box foundation of 22.5m x 15m x 14.25m (depth) with a base slab of, varying thickness was proposed. The subgrade reactions, bending moments and settlements needed to be determined by means of in-situ model test. A model of the same materials as the prototype scaled to l/10 was embedded in-situ with simulated depth in the bedrock. A lot of data obtained from 39 bench marks, 32 elongation measuring points, 30 couples of electric resistance strain gauges and 24 pressure cells attached to the model foundation enables all the quantities required to be found out. Since it was put into operation, the settlements measured has reasonably agreed with the test results and the foundation has been in good condition.

Jan 1, 2010

By Dongwook Kim

Recently, load and resistance factor design (LRFD) is gradually being adopted internationally in geotechnical design due to the advantages of LRFD over the existing allowable stress design (ASD). LRFD is a more advanced design method compared to the ASD because resistance factor is calibrated based on the reliability analysis for a given target reliability index. Target reliability index changes with the importance of the structure. Typically, target reliability index of offshore foundation is less than those of onshore. The widely-used Imperial College Pile (ICP) design method is used for the calculation of pullout capacity of driven piles. The uncertainties regarding pullout capacities of driven piles are assessed using the statistical data reported in the literature. The first-order reliability method (FORM) is used to calibrate resistance factors for the pullout ultimate limit states of the driven piles for three different levels (2.5, 3.0, and 3.5) of target reliability index. The load factors used in this paper are the ones proposed in the AASHTO LRFD bridge design specifications.

Jan 1, 2010

By Scott Webster

Dynamic pile Monitoring Services (DMS) have been used for testing of offshore piles for several decades. However, most of this testing was to measure hammer performance and pile stresses rather than pile capacity or soil resistance. As the need for more economical solutions for foundation support increases, the use of DMS has provided a better means of evaluating in-place pile capacity for offshore structures, and therefore a method of determining pile acceptance. The authors have been involved in several offshore projects where DMS has been the primary source of data for acceptance of the driven pile foundations. The use of DMS for evaluation of offshore foundations requires considerations quite different from land applications and these considerations are often necessary for the careful and thorough analysis of the collected data in nearly real time for determination of pile acceptance. Case Method capacity estimates are often of little use due to the non-uniform cross sections of the foundation piles and their deep penetrations. Therefore, capacity assessments should be made using CAPWAP which is a signal matching program whose utility and reliability has been proven on thousands of projects every year, both on land and offshore. Depending upon the soil conditions at a given location, capacity assessment after soil setup effects may be necessary. In addition, tension capacity is often critical when pile refusal occurs significantly before the design pile penetration depth. Evaluation of uplift capacity can be accomplished by a CAPWAP analysis, which results in a total capacity prediction and its shaft resistance component. The use of hydraulic hammers for driving of these piles also adds the requirement of controlling hammer energy such that over-stressing of the pile is avoided. The calculation of non-axial stresses such as bending or eccentric stresses may also be involved in order to prevent pile damage.

Jan 1, 2010

By Richard J. Hartman

This presentation identifies some of the more common problems associated with cofferdam construction. After the various problems are identified, they are briefly explained and possible solutions and preventive measures are noted. Photographic slides used during the seminar illustrate the conditions. This discussion is limited to cofferdams which are braced structures excavated inside to allow access for construction. The common procedure is to drive sheet piling and then alternatively install bracing and excavate. They can be located either on land or in water. Loads are applied by soil, water, surcharge pres-sure, eccentricities, and impact loads. The loads are resisted by the sheet piling, the bracing, and the soil below the bottom of the excavation; each of these three components must be capable of resisting the applied loads.

Jan 1, 1987

By Jean-Louis Briaud

The following is a summary of a very recent report prepared at Texas A&M University for the National Cooperative Highway Research Program and entitled "Downdrag on Bitumen Coated Piles". Anytime the soil settles more than the pile, downdrag or negative skin friction will develop. The load in the pile increases with depth up to a certain point and then decreases down to the pile point. This phenomenon has been quoted as being the number one culprit for deep foundation failures. In Chapter 1, an introduction to downdrag is given. The most common criterion for downdrag is to consider it in design as soon as the settlement of the soil surface after pile driving exceeds 0.5 in. Coating piles with bitumen is an effective way of reducing downdrag forces and therefore allows to use smaller piles for the same load. This results in cost savings. Coating piles with bitumen increase the cost of piles by about 33% and therefore the decision to use bitumen is generally based on economic considerations.

Jan 1, 1989

By Seth H. Hamblin, John E. Regan, Dimitrios Palantzas

"Through reliability-based calibration of larger pile load test databases, recent developments of the Load Resistance Factor Design (LRFD) methods, which include geotechnical load and resistance factors for deep foundations design, have advanced the state of practice for geotechnical engineering. These load test databases upon which the current geotechnical load and resistance factors have been developed are limited, however, and do not provide sufficient data to support the development of resistance factors for uplift (tension) pile capacity. As such, some recommended resistance factors for uplift capacity estimation methods are simply derived by reducing the recommended resistance factors for piles in compression by a factor of 0.10.The results of three (3) tension loading tests performed to failure on 508 mm (20- in) square precast, prestressed concrete piles, driven though granular soil in southeastern Massachusetts, are presented and compared to static pile capacity calculations and dynamic analyses performed using the Pile Driving Analyzer (PDA) during installation. These results are presented along with current recommended LRFD resistance factors for driven piles under uplift (tension) loading conditions. These comparisons offer an assessment of the applicability and limitations of current resistance factors methods for piles under uplift loading and may be useful additions to the existing database for future calibrations of LRFD resistance factors for driven prestressed concrete piles in sand.IntroductionIn 2010, two (2) natural draft cooling towers were constructed by Kiewit (Kiewit) Construction Company of Woodcliff Lake, New Jersey at the Brayton Point Power Station in Somerset, Massachusetts. These massive 500 foot tall, 400 foot diameter cooling towers were designed to convert the existing “open loop” system into a “closed loop system” thereby dramatically reducing the thermal impact to Mt. Hope Bay.Based on design guidance from the German VBG Design Code and the Massachusetts State Building Code (MSBC), tension (i.e. uplift) and lateral loads due to wind loads and design seismic events represented the critical loading conditions.Weighing approximately 190,000 kips upon completion, the cooling tower loads are transferred to 44 foundation nodes (i.e. pile caps) evenly spaced along ring beams which run the circular perimeter of each tower base. Each pile cap node was designed to resist a 2,000 ton compression load, 200 tons in tension (i.e. uplift), and 600 tons in the lateral direction."

Jan 1, 2015

By Roger A. Bullivant

As the UK's foremost domestic foundation underpinning contractor over the last 25 years it has become abundantly clear that the size of the repair market, some £500m per annum is a significant waste of resource and cost. To experience this scale of foundation failure in mainly new construction less than 20 years old is unacceptable. This is being further endorsed by our contracting experience in the USA over the last 10 years. Our foundation repair systems are mainly based upon the use of driven mini piles and it was considered appropriate that this type of pile should be upgraded and used on new build construction where the ground was marginal or bad.

Jan 1, 1995

By Allan Herse

"The years following World War II were nation building years in Australia. Soldiers returned from the European and Asian theatres of war sparking a major infrastructure construction boom. Dams and highways were built to keep up with the growth of towns and cities, which were bursting at the seams, not just from the returning soldiers settling down with their families but also from the many waves of refugees from war torn areas around the globe.The demand for electricity generation and distribution required for the growing population sparked the expansion of the national power grid with new high-voltage transmission towers appearing across the landscape. However, with an original design life of 50 years, those transmission lines constructed in the 1950s are nearing, or are at the end of, their anticipated service life.In recent years, the Australian power distribution network has changed from a period of high construction activity in greenfield high-voltage lines to a period that is now focused on reducing cost and maintaining existing assets. Replacing aboveground structural members and electrical components is relatively simple even under live conditions. However, the replacement or repair of tower foundations, many of which are in remote locations, has been a problem that has caused difficulties for power utilities trying to operate on a budget while also avoiding costly and unpopular power outages.With thousands of miles of aging transmission lines needing life extension work, Piling & Civil Australia (PCA) has developed a patented system of upgrading the foundations with micropiles while under live-line conditions without requiring costly outages. The system is seen as revolutionary by power utilities, allowing the utilities to extend the life of their existing assets until demand increases to warrant the construction of a new line. PCA has been working on a potential solution with Powerlink Queensland for the past 5 years to develop a quick and cost-effective foundation replacement system that can extend the life of its existing asset base anywhere from an additional 5 years to 50 years.With design support from Quanta Subsurface, USA, PCA recently completed the foundation replacement of 26 lattice tower foundations in the Townsville region of North Queensland. Using a steel bracket (patent pending) to connect hollow bar micropiles to the lattice towers, the installation techniques that were developed enabled the micropiles to be installed within a tolerance of less than about 3/8 in (10 mm) through the existing steel grillage foundation while maintaining live line conditions. The project was an Australian first and a trial by Powerlink for wider use within its network, and it was delivered on time and within budget at one tenth of the cost of traditional methods."

Jan 1, 2017

By Allan Herse

"The years following World War II were nation building years in Australia. Soldiers returned from the European and Asian theatres of war sparking a major infrastructure construction boom. Dams and highways were built to keep up with the growth of towns and cities, which were bursting at the seams, not just from the returning soldiers settling down with their families but also from the many waves of refugees from war torn areas around the globe.The demand for electricity generation and distribution required for the growing population sparked the expansion of the national power grid with new high-voltage transmission towers appearing across the landscape. However, with an original design life of 50 years, those transmission lines constructed in the 1950s are nearing, or are at the end of, their anticipated service life.In recent years, the Australian power distribution network has changed from a period of high construction activity in greenfield high-voltage lines to a period that is now focused on reducing cost and maintaining existing assets. Replacing aboveground structural members and electrical components is relatively simple even under live conditions. However, the replacement or repair of tower foundations, many of which are in remote locations, has been a problem that has caused difficulties for power utilities trying to operate on a budget while also avoiding costly and unpopular power outages. With thousands of miles of aging transmission lines needing life extension work, Piling & Civil Australia (PCA) has developed a patented system of upgrading the foundations with micropiles while under live-line conditions without requiring costly outages. The system is seen as revolutionary by power utilities, allowing the utilities to extend the life of their existing assets until demand increases to warrant the construction of a new line. PCA has been working on a potential solution with Powerlink Queensland for the past 5 years to develop a quick and cost-effective foundation replacement system that can extend the life of its existing asset base anywhere from an additional 5 years to 50 years.With design support from Quanta Subsurface, USA, PCA recently completed the foundation replacement of 26 lattice tower foundations in the Townsville region of North Queensland. Using a steel bracket (patent pending) to connect hollow bar micropiles to the lattice towers, the installation techniques that were developed enabled the micropiles to be installed within a tolerance of less than about 3/8 in (10 mm) through the existing steel grillage foundation while maintaining live line conditions. The project was an Australian first and a trial by Powerlink for wider use within its network, and it was delivered on time and within budget at one tenth of the cost of traditional methods."

Jan 1, 2017

By David A. Hart, Barry P. Osborn, Richard J. Totty, Ana T. Carvalho, Max B. Elliott

This paper addresses the experience designing and installing bored piles for the King’s Cross area. This includes continuous flight auger and rotary bored piles, with a range of diameters between 600 mm and 1200 mm, reaching a maximum depth of 56 m below ground level. Existing Network Rail Thameslink twin bored running tunnels are located directly beneath the subject plots. These tunnels have an external diameter of 6.6 m and the crowns of the tunnels are very shallow, in some cases just 10 m below the existing ground level. Some plots needed piles to be installed in close proximity to the tunnels, which required additional control measures and contingency plans. Pile verticality was monitored as the tip of each pile advanced and in-tunnel monitoring readings were verified and are presented. Lessons learned from designing, installing and testing the piles and monitoring the tunnels are addressed in this paper.

May 1, 2022

By Packer M. L

Residual load development in driven precast piles has been widely researched in recent decades, however, cast-in-situ piles are often falsely assumed to be unaffected by this mechanism. In contrast to driven precast piles, driven cast-in-situ (DCIS) piles require adequate time prior to loading for the concrete hydration and curing processes to occur. The concrete-soil interaction is complex with several processes influencing the strains within the concrete pile after installation. DCIS piles are of particular interest given that residual loads can be developed during both the driving and casting phases. This paper present four instrumented end-bearing DCIS piles in which temperature and strains were monitored from installation, with the objective of identifying the processes contributing to the measured strains prior to testing. Strain gauges at all depths recorded a net compression and compressive strains continued to increase up to the commencement of load testing. Residual strains in the test piles were interpreted to be influenced by temperature (concrete and ambient soil and air temperature), consolidation of soils due to dissipation of excess pore water pressure, and swelling from absorption of groundwater. Several residual load interpretive methods are evaluated with the Siegel and McGillivray (2009) approach being consistent with the skin friction full mobilisation theory of the Unified Design method. The full-scale field tests presented herein provide a unique opportunity to examine DCIS pile behaviour, particularly given the lack of presently available published studies on these pile types.

May 1, 2022

By Kyle Kershaw

Micropiles are routinely used in the United States for foundation support and stabilization of slopes. In recent years, several retaining walls have been constructed using micropiles in an A-frame type configuration to support temporary and permanent excavations at sites with limited access and limited right-of-way. Typical A-frame micropile walls consist of a row of vertical micropiles at the face of the wall and a row of battered micropiles extending into the soil or rock to be retained. The two rows are then tied together with a pile cap such that the front pile acts primarily in bending and the back pile acts primarily in tension. Because of tight right-of-way constraints at a residential site in Aspen, Colorado, it was not possible to construct the wall using conventional shoring systems or micropiles in the typical A-frame configuration. Rather, the wall was designed such that the row of battered piles was installed at the wall face and the row of vertical piles was installed adjacent to the property line behind the wall. As a result of the reverse configuration of the A-frame wall, FLAC, a two-dimensional, finite difference software program, was used to model the soil-structure interaction. The final wall design consisted of both temporary and permanent retaining wall sections with maximum heights of 26 feet. Inclinometers were installed in several piles to monitor the behavior of the retaining walls during and after excavation. This paper presents an overview of the design method, a discussion of construction techniques, and a comparison between the FLAC model and the measured behavior of the wall in the field.

Jan 1, 2007

By Kiyotaka Ohno, Nobushige Yasuoka, Yosuke Hioki

"The diameter of improved columns adopted by the original DJM Method had been 1000 mm, however, in order to comply with the social need for construction cost reduction, the Expanded Dry Jet Mixing (EX-DJM) Method with maximum column diameter expanded to 1300 mm was developed between 1998 and 2001 and has been widely applied since then. From the first application of EX-DJM in January 2002 for a first construction project, the total volume of improved soil has reached 325,000 m3 in 17 projects up to September 2014. Because of the advantages of the EX-DJM such as reduction of construction costs and periods leading to reduction in the number of improved columns, adoption of this method is expected to increase in the future. This paper describes the advantages of the EX-DJM, its construction results and case examples including those applied to restoration projects after the Great East Japan Earthquake, 2011.1. BACKGROUND OF DEVELOPMENTThe Dry Jet Mixing (DJM) Method is a soil stabilization method in which a powdery or granular binder is pneumatically fed into and mixed with soft soil to induce chemical reactions that stabilize and strengthen the soil. It was developed by government - private collaboration in Japan between 1977 and 1979. Up to March 2014, the total volume of soil improved by DJM method reached 33,500,000 m3. The initial diameter of improved columns of the original DJM Method was 1000 mm. In order to comply with the social need for construction cost reduction, the Expanded Dry Jet Mixing (EX-DJM) Method with maximum column diameter 1300 mm was developed between 1998 and 2001.2. ADVANTAGES OF EX-DJMThe construction equipment for the EX-DJM consists of two major parts, which are DJM machine and binder plant are shown in Fig. 1.The construction machine is of double mixing-shaft type with its column diameter expanded to 1200mm or 1300mm. In association with the increase in the column diameter, the binder feeder has also increased its discharge rate by approximately 1.69 times. Same as the increase rate of the area of original diameter 1000mm to diameter 1300mm are shown in Fig. 4."

Jan 1, 2015

By Mike Muchard

STATNAMIC load testing augmented with embedded instrumentation has been successfully used to obtain structural and geotechnical design information on large diameter spun cast concrete cylinder piles on many large marine construction projects. The paper focuses on one particularly interesting large marine project involving a new bridge to St. George Island, Florida where instrumentation and STATNAMIC load testing was used in conjunction with static load testing on high capacity piles. The information presented includes embedded instrumentation measurements taken during pile fabrication (post-tensioning), during pile driving, during static load testing, and STATNAMIC load testing. As much of this data is the first of its kind on concrete cylinder piles, it is exciting to present the foundation industry with this additional insight as to the behavior of this pile type and the accuracy of the methods used to test them.

Jan 1, 2013

By Dario Libano

"The Line 5 Extension, in Sao Paulo, Brazil, is currently the most important investment in public transportation by Sao Paulo’s state government. It will connect the south part of the city to the city center, crossing through four other major Metro lines and stations; all currently in operation. The total extension of the line is 11 km (6.8 mi), and includes a new parking yard for the trains and 11 new stations. The Brooklin Station, one of the new stations due to be open and operating in 2016, has a unique geometry of five secant shafts.The original design included constructing five secant shafts stabilized by two plastic slurry walls using conventional grab technology. One slurry wall, along the Santo Amaro Avenue, was to contain the contamination plumes, and another was for temporary support to enable the excavation of the shafts. The final retaining wall design was changed to a concrete structural diaphragm wall that reduced the construction time of the shafts by half, allowing the contractor to meet the construction schedule. This solution also avoided dewatering effects in a geological region characterized by Quaternary sediments and environmental contamination plumes. It was the first time that a hydromill was used in such a situation in Brazil. The hydromill, by overcutting the panels, increased the quality of the joints, and decreased the probability of having seepage into the shafts. The hydromill also created a seepage barrier and avoided movement of the contaminated plumes.The GeologyLocal geology is composed of a superficial Quaternary soil, basically soft organic clays and sands and gravels. From the depth of 8 m (26 ft) until 18 m (59 ft), geology is composed by tertiary medium compact sand with thin silt-clay layers. From 18 m (59 ft) down, there are alternations between compact silt-sands layers with very hard clays layers. Each is approximately 5 to 10 m (16.4 ft to 33 ft) thick.The Initial Basic DesignThe original basic design of the Brooklin Station was to be constructed from five 40 m (131 ft) diameter intersecting circular shafts, all in a line along the axis of the Metro tunnel, in 555 days. In the excavation sequence, the odd shafts were first excavated, waterproofed and had part of their inside cast-in-place structure built before the even shafts were excavated. During the excavation of the even shafts, part of the odd shaft’s support was demolished and connected with the even support. A 0.8 m (2.6 ft) thick plastic slurry wall, acting together with the wire mesh reinforced shotcrete support, ensured the excavation stability around the five shafts."

Jan 1, 2014

By Kevin Kuhl

With the destruction of the US-90 Bridge spanning St. Louis Bay by Hurricane Katrina, the State of Mississippi awarded its first major design-build contract in order to have a completed four-lane bridge in a period of less than two years. The structure consists of 76 pre-cast concrete beam spans with a total bridge length from Bent 1 to Bent 77 of 11,124 ft (2.1 miles). All 77 bents are founded on pre-cast, pre-stressed concrete piles and consist of two foundation types: pile bents and water line footings. A total of 53 pile bents were utilized where the deck is less than 52 ft above the water. Further divided, 10 pile bents, supported by 24 in. square, solid piles, are located on land. The remainder of the pile bents are located within St. Louis Bay and supported by 36 in. square, voided piles. All the waterline footings are supported by 30 in. square, voided piles. In total, 138 -24 in., 437 -30 in., and 463 -36 in. piles support the structure. Production pile design was based upon information gathered from the subsurface investigation, design soil profile and 23 out-of-position test piles. Verification of the design was established by monitoring the first production pile driven at each bent using the Pile Driving Analyzer. Particular challenges included highly variable coastal deposits, loads in excess of 1600 kips per pile and a compressed construction schedule. Initial drive capacity of a portion of the production test piles was less than expected resulting in a minimum 14 day setup. Following the setup period, restrikes were necessary to verify capacity. Project production piles ranging from 50 ft in length to in excess of 160 ft in length were used to achieve the required resistance. This paper includes a brief overview of the foundation design and indicator test pile program. The main objective is to provide a summary of the quality control procedures including establishing the driving criteria for each bent and to present issues that arose during production pile driving and the solutions that followed.

May 11, 2007

By C. Michael Morgano

Static tests are costly and time consuming, so they are not always the best answer [ ]

Jan 1, 2005

By Richard T. Stain

"In 2001, a pile trial site was established at Limelette in Belgium consisting of 25 displacement screw piles and 5 driven pre-cast piles. Interested parties were invited to participate in a pile prediction event, whereby they would submit predicted static load test behaviour in the form of load settlement plots. These predictions could be based on soil investigation results supplied by the organizers, or dynamic load test measurements.Following the submission deadline, the organisers released the results of static load tests for comparison.Of all the six participants, including Statnamic, the SIMBAT method was independently accredited with achieving the best predictions.This paper examines at the differences between SIMBAT and other systems, and presents the correlations from the Limelette trial.INTRODUCTIONThe Belgian Building Research Institute (BBRI) initiated an ambitious research programme involving the construction and testing of some 60 trial piles spread between two sites, a clay site at Sint Kateline Waver and a sandy site at the BBRI headquarters at Limelette. The project was financed largely by the Belgian Ministry of Economic affairs. (ref 1.) This paper refers only to the second site.At Limelette, six different types of displacement pile were installed: one driven pre-cast and five cast in place screw piles - Atlas, DeWaal, Fundex, Olivier and Omega. A detailed site investigation was carried out including in-situ and laboratory tests.An international pile capacity prediction event was publicised, participants being invited to predict static pile behaviour. Predictions could be based on:"

Jan 1, 2005

By John C. Niedzielski

The existing US-70 Bridge over the Gila River at Bylas, Arizona is planned to be replaced due to its current poor condition. The replacement bridge is planned to be a 15-span, 1,904-foot (580 meter) long bridge, the third-longest bridge in the state highway system. Within the Gila River floodplain, granular alluvial soil is underlain by cohesive lacustrine soil; bedrock was expected due to nearby terrain but not encountered within the geotechnical exploration depth of 166.5 feet (51 meters) or less. Based on the anticipated loading conditions, design scour depths and the soil conditions, the full structural loads are carried by large diameter drilled shafts; therefore accurately determining the axial capacity of the proposed drilled shafts has important practical and safety implications. The conventional methods for axial capacity determination may be overly conservative to use for design in the site?s layered granular and hard clay soils. An Osterberg cell load test was performed to obtain detailed information on the load transfer from the drilled shaft in side friction and base resistance to allow optimization of the bridge foundation design. The full-scale field test played a significant role in the design of the project?s deep foundations, notably, by incorporating the specific subsoil properties and consequently, an exact prediction of the load-settlement behavior under loading. This paper provides the results of the geotechnical site investigations, drilled shaft load testing procedures, and shaft load distribution from the load test results. Comparisons were developed between predicted axial capacities of drilled shafts using several design methodologies and the axial capacity measured from static load testing. The load test results showed that underestimation of the axial capacity is evident using conventional methodologies. The exact prediction of the load-settlement behavior under loading combined with a site-specific design approach, resulted in a substantial reduction of foundation costs due to reduced drilled shaft dimensions.

By Monique Nykamp

"INTRODUCTIONTerminal 46 is located just south of downtown Seattle, and is one of the Port of Seattle’s busiest container terminals. The Terminal 46 Redevelopment Project was undertaken to replace the existing 15-m-wide (50 ft) cranes along the apron with 30-m-wide (100 ft) cranes, which can unload larger, post- Panamax ships. The project included upgrading the existing waterside crane rail with new piles and constructing a new land-side rail behind the sheetpile bulkhead. The new piles had to be installed adjacent to the existing apron without causing damage, which was a signifi cant geotechnical challenge due to the soft soil conditions at the site. An instrumentation program performed during the test pile program evaluated this challenge and allowed for the development of specifi c production pile installation procedures that had the least possible effect on construction costs and schedule. SITE HISTORYThe site lies along the west side of Elliott Bay, north of the mouth of the Duwamish Waterway. Prior to development, this area was part of the tide fl ats where the Duwamish River drained into Elliott Bay. Prior to 1970, there were several existing timber piers and structures in the area. In the 1970s, the Port of Seattle constructed a 900-m-long (3,000 ft), 30- m-wide (100 ft) apron to support fi ve, 15-m-wide (50 ft) container cranes. The contained backland area was then fi lled with dredged spoils (sand and silt with organics) and the upper 5 to 20 m (16 to 65 ft) backfi lled with sand and gravel.The existing apron was constructed using 0.4 m (16 in) octagonal prestressed concrete piles to support the precast concrete deck and crane rails. The pile-supported bents were spaced at 6.1 m (20 ft), center-to-center, along the longitudinal direction. Pile lengths typically varied from about 20 to 40 m (65 to 130 ft) with 15 to 26 m penetration below mudline (50 to 85 ft penetration). The slope below the apron was constructed at about 1.75 horizontal to 1 vertical to allow for suffi cient water depth for cargo ships. In most areas, a riprap buttress was placed at the toe of the slope. A typical cross section of the apron is shown on Figure 2.Several stability, settlement and pile driving issues arose during the original construction of T-46 (Pita, 1983). Reportedly, movement of the submarine slope occurred during pile driving, resulting in settlement behind the bulkhead. Pile driving reportedly caused settlement of adjacent piles. In addition, some piles were “running” (dropping quickly under one hammer blow) during installation."

Jan 1, 2007