Search Documents

By Joel Moskowitz

A new office complex is being constructed within 25m of the Hudson River in New Jersey. The project, about 140 m by 100 m, will include 4 basements under the entire footprint. The perimeter was to be secured by a 0.8 m thick diaphragm wall, laterally supported by high capacity tieback anchors to rock. Columns were to be supported on footings or piers to rock at a nominal bearing pressure of 3.8 MPa at depths up to 17m. Although some variation in rock quality was observed in borings, a substantial vertical seam of weathered and/or decomposed rock, 1 to 2 meters wide by as much as 8 meters deep, was encountered during construction necessitating field redesign. In some locations the seam dipped below more competent rock. Footings were redesigned for support on drilled caissons, or soft rock was excavated and replaced with concrete necessitating a reduction in bearing pressure of the footings by one half.

Jan 1, 2002

By J. -M. Rescoussier

Due to Important settlements inducing major structural damages, the western part of the Grand Littoral shopping centre has been closed in 1997. The present paper describes the project of underpinning including not only micropiles under the structure of the building but also a reinforcement of the soil located between the shopping centre and the edge of the embankment surrounding the western part of the shopping centre. The aim of this reinforcement is to reduce existing horizontal movements to allowable values.

Jan 1, 2002

By Rolf Katzenbach

The principle questions related to the design of deep foundations especially in soft soils are the stability and the cost optimised settlement reduction to prevent possible damages and to minimise the deformations of the adjacent infrastructure. The present develop­ments in the design of deep foundations lead to the design approach of the Combined Pile-Raft Foundation (CPRF) which offers a lot of new possibilities, e.g. the utilisation of the CPRF for horizontal loading or the use of the subsoil as a geothermal storage system.

Jan 1, 2006

By Camilla Favaretti, Benjamin Turner, Anne Lemnitzer

Pile foundations are extensively used in the construction of various types of superstructures, including tall buildings, bridges, freeways and offshore structures. A fully constrained tip embedment such as a rock-socket offers an attractive solution for achieving significant tip resistance and improving the load-carrying capability of the foundation element. In profiles with very soft surficial soil, rock-socketing often provides the only reliable source of axial and lateral resistance. In preparation of a large-scale testing program on rock-socketed piles at UC Irvine (UCI) geared towards studying the magnitude of shear amplification at the rock-soil boundary of pile foundations, a pre-test model-scale experiment was executed in the UCI Structural Laboratory. The objective of the model-scale experiment was to iterate and validate the test setup, study the influence of important boundary conditions, assess instrumentation techniques and sensor placement, and to gain preliminary insight into the small-scale specimen non- linearity. In addition, this model-scale study provides ample opportunity to compare lateral performance parameters with analytically predicted lateral load behavior using traditional soil resistance functions and limit state analyses and explore new techniques for the derivation of soil resistance functions. The pile specimen had a pile diameter (D) of 10 inches and a total pile length of 125 inches. The pile was embedded in a 40 inch simulated rock socket overlain by 52 inch of medium dense sand (DR~50%). The pile extended 32 inches above the soil surface, where cyclic lateral loading was applied. The pile was installed in a laminar metal frame box with inside dimensions of 39 inches in width (W), 73 inches in length (L) and 86.1 inches in height (H) as shown in Figure 1. During testing, the box was restrained using a rigid bracing system consisting of concrete reaction blocks, wooden braces and steel girders.

Jan 1, 2018

By William E. Lardner

Interlocking caisson walls developed from conventional "soldier pile and lagging" shoring. In the latter, the soldier piles receive directly most of the soil load. Natural arches form in the soil behind the shoring; the lagging supports little more than the segment of soil inside the arch. Fig. 1: A typical layout of a lagged wall [ ] Fig. 2: A typical layout of an interlocking caisson wall [ ]

Jan 1, 1987

By M. B. Wechsler

An analysis is developed for determining the maximum loading, as well as the potential uplift of the piles on bridge pier foundations. There are considered piers supported on two through seven rows of piles, and related to two simply supported collinear superstructures of any structural material. The study leads to different types of influence lines for various load combinations. For load combinations containing vertical loads only, the related influence lines are similar to those as for the bending moments of a virtual span covering the two actual spans, as well as the gap between the two superstructures; and, in this case, the heavier loads should be positioned in the vicinity of the pier. While, in the case when vertical loads are acting together with hori­zontal forces, the related influence lines will indicate where the heavier live loads should be positioned. And they will also indicate on which portions of the spans the live load should be avoided.

Jan 1, 1989

By Thomas C. Anderson

Thirty-four retaining walls are part of the $46 million upgrade of a 1942 depressed highway in Highland Park, Michigan near Detroit. This project will close a missing link between two newer roadways, I-75 and the John Lodge Freeway. The existing 75 ft. wide, six lane Davison Freeway is being replaced by a eight to ten lane, 200 ft. wide depressed highway in a limited right of way. The highway will be 20-25 ft. deep and 1.5 miles long. A design/build decision by the Michigan DOT saved about 37% of the engineers estimated cost of $19 million for the walls. The successful pre-qualified specialty contractor utilized an innovative solution for the walls consisting of tiedback/cantilevered walls on the north side and mechanically stabilized earth walls on the south side. All of the walls have an identical cast-in-place architectural facing.

Jan 1, 1999

By John A. Dal Pino

This paper describes two independent building underpinning projects during the construction of the Los Angeles Metro Rail System. The first project involves pinpile underpinning of a building along the Red Line which is the main heavy-rail portion of the system. Vertical and inclined friction pinpiles were constructed, using drilling equipment in a low-overhead height space, to support underpinning grade beams. This underpinning permitted the demolition of the building caissons so that the subway tunnels could pass beneath the building unimpeded. One of the piles was statically tested in compression. The second project involves the use of traditional pit piers for the underpinning of historic buildings along the Pasadena Blue Line, which is one of the light-rail branches from the Red Line. The piers were designed for various loading conditions and to minimize differential settlement of adjacent foundations. The piers will be internally braced with steel struts to be designed by the contractor.

Jan 1, 1996

By Roger Frank

"Abstract After noting the importance of standardization for piles, the European system is described (execution, tests and design, etc.). Some important aspects of Eurocode 7 are outlined (like the role of pile load tests). Finally, the calculation methods in the recent French standard for the design of piles following Eurocode 7 are shortly addressed.Importance of standardization for piles Like for other fields of geotechnical engineering, pile engineering is a complex art. For piles, the challenges are particularly numerous and many things must be mastered properly: - the soil investigation must be serious and adequate (for instance, deep enough!);- the choice of the pile type and the assumed behaviour must be assessed in order to reach a safe and economic design of the overall foundation;- the execution itself (construction and/or installation) deserves special attention and must follow strict state-of-the art rules.The geotechnical engineer, in charge of the design of a pile foundation, must have in mind the parameters linked to the variety of soils, of soil conditions and of pile types. A wide range of strong environmental issues are also to be considered: minimum disturbance during the execution processes, long-duration friendliness of the “inclusions” into the ground (to avoid pollution of the soils and waters, for instance) and respect of the neighbouring structures.Pile engineering plays in a world which is constantly moving and progressing: constructions expand in new difficult areas, actions on piles are more and more important, new execution techniques of piles are developed, research into the complex behaviour of pile foundations has no end, etc. Our views on how piles and group of piles really work are constantly evolving!"

Jan 1, 2014

By Lianyang Zhang

For optimal design of rock socketed shafts used to support axial loading, it is important to predict the end bearing capacity. The existing empirical methods for determining the end bearing capacity of rock socketed shafts use the empirical relations between the end bearing capacity, qmax, and the unconfined compressive strength of intact rock, sc. Since rock socketed shafts are supported by the rock mass (both intact rock blocks and discontinuities separating them) not just the intact rock, one should consider not only the intact rock properties but also the influence of discontinuities when determining the end bearing capacity. Although the effect of discontinuities may have been implicitly (partially) included in the empirical relations derived from the results of load tests, it is not clear how big the effect is and how much of it has been included. In this paper, a database consisting of 50 test shafts, 25 of which contain the RQD (rock quality designation) value, is developed. Using the database, the applicability of the existing empirical relations is evaluated and two new empirical relations between the end bearing capacity, qmax, and the unconfined compressive strength of rock mass, scm, are derived. The new empirical relations explicitly consider the effect of discontinuities by using scm which is directly related to RQD. Finally, an example is presented to demonstrate the application of the newly derived relations.

Jan 1, 2008

By Venda Oliveira P. J., Correia A. A. S., Danisi C. M.

"AbstractA laboratory study has been undertaken to establish common understanding of the creep phenomenon of a Portuguese soft soil chemically stabilised with binders. In order to study the effect of different stress levels on the strength and on the creep behavior of the stabilised soil, oedometer creep tests and unconfined compressive tests were performed at different curing times. Results show that the creep stress level does not influence the unconfined compressive strength. In addition, the creep phenomenon increases the unconfined compressive strength of the treated soil. Two different secondary compression indexes were recognized from the one-dimensional compression curve which increase with an exponential trend with the creep stress level.IntroductionConstruction on soft soils requires a mandatory soil stabilization work to improve mechanical characteristics of the natural soil. Deep mixing method is a worldwide employed ground improvement method, nevertheless the creep phenomenon hasn’t been yet thoroughly analyzed. Most of the published papers have focused on the analysis of the compressibility and the strength of the soil-binder mixtures without considering the creep phenomenon. However, numerical results (Venda Oliveira et al. 2009) have shown that although settlements that occur during the creep stage (namely creep strains) are less in case of treated columns, they are still important especially due to the high loads applied to the stabilised soil. The few published studies about creep behavior of soil-binder mixtures reveal that the stabilization of an organic soil with cement induces a reduction of creep deformations, which is related to the amount of cement used and that the increase of the organic matter of the soil has a negative impact on soil stabilization, further inducing a slight increase in the creep deformations (Venda Oliveira et al. 2012).As part of the current research the effect of different stress levels on the creep behavior of a soft clayey-silt soil was studied. The binder mixture used to enhance the properties of the soil had a specific composition and quantity. Unconfined compressive strength tests (UCS) and UCS creep tests were carried out at pre-set curing times in order to analyze the creep behavior of the soil-binder mixture. In particular five different creep stress levels were studied to understand its influence on the strength and on the compressibility of the stabilised soil. In addition, considerations about the secondary consolidation index are also presented."

Jan 1, 2014

By G. R. Dasari

New Austrian Tunnelling Method (NATM) has been analysed by Finite Element method in two and three dimensions by Strain Dependant Modified Cam Clay (SDMCC) Model. The effects of construction sequence, stiffness of shotcrete and time dependency of shotcrete on surface settlement magnitude due to the NATM have been studied. Settlements obtained in 2D analysis, as expected, found to be more than the observations. The surface settlements obtained in 3D analysis found to be about 3 times less than equivalent plane strain analysis. This is due to mobilisation of soil strength around the tunnel face and soil-tunnel lining interaction. About 40% settlements occurred due to excavation of face at the monitor section and 60% after the excavation crossed monitor the section.

Jan 1, 1996

By Enrique Ibarra, Manuel J. Mendoza

"Abstract: This paper describes the current state-of-practice for the design of cast-in-place drilled shafts in granular soils under axial loading, addressing recent advances that take into account the surrounding soil grain size distribution and their behavior. The important role of the gravel content in the shaft response under axial loading is emphasized. Usual design approaches in Mexico are described, and the results of load tests from different sources are discussed. The analysis emphasizes the primary contribution of the lateral area of shafts to their axial bearing capacity, raising doubts regarding the common local idea of “point bearing shafts”. Finally, some lines of research are noted to permit advances in the important field of deep foundations. 1 INTRODUCTIONIn Mexico, cast-in-place drilled shaft foundations are widely used to support various structures in the west area of Mexico City, where alluvial and volcanic deposits predominate. Deep foundations are also used in modern construction works located in other major cities of Mexico. In fact, the use of drilled shafts for tall buildings and overpasses in the center of Guadalajara as well as in transportation works related to the Metro and roadways in Monterrey is well known. It is worth mentioning that these same structures have been applied in road bridges throughout the country.Procedures for pile construction in Mexico have been basically the same for the past 20 years (Paniagua et al., 2005); however, modern equipment has been incorporated into the construction industry, including innovations in sludge-drilling technology, control and the quality of the castings. In addition, novel and efficient procedures such as construction with continuous auger displacement piles have been implemented (Auger Cast in Place, ACP) and have begun to be used locally with success (Schmitter and Paulin, 2006).However, it can be argued that the technological developments that have resulted in more efficient construction procedures have not included a breakthrough in the full understanding of the phenomena or basic mechanisms of load transfer from piles to the surrounding subsoil and therefore in supported, tested and practical design methods. This is particularly true when seeking to determine the unit side shear strength of shafts drilled in granular media with gravels, where it has been observed that the commonly used calculations developed for sands underestimate the load-bearing capacity by frictionin a most important way. Due to the above reasons, it seemed appropriate to present in this paper a review of the current stateof- practice in Mexico for the design of cast-in-place drilled shafts, particularly in granular media, highlighting some recent advances and research that takes into account the grain size distribution and behavior of granular soil."

Jan 1, 2014

By S. Narasimha Rao

Bored cast in situ piles are highly susceptible to construction defects like necking, discontinuity in concreting, poor compaction of concrete, improper end bearing condition due to inadequate cleaning of bore hole, exposure of reinforcement, segregation of concrete etc. There is a necessity to understand the behavior of piles so as to design effective foundation system. In this paper investigations of two field cases were discussed to bring out the effect of defective piles. In one case improper end bearing has been discussed for a concrete pile of length of 45m and diameter equal to 1.2 m and is reinforced with 32 no's of 28mm diameter steel bars and in another case necking of the pile has been discussed. Further model piles with preformed defects have been tested in laboratory to bring out the influence of defective piles.

Jan 1, 1996

By A. Mazzucato

This paper presents the experimental results of driving and load tests on an instrumented pile driven into a test pit filled with fine homogeneous sand.

Jan 1, 2010

By K. Rainer Massarsch, Bengt H. Fellenius

"Abstract Vibrations generated during the driving of piles or sheet piles can affect buildings or installations in the ground. However, observed building damage is not always caused directly by dynamic effects, but can also be related to foundation conditions. The importance of geotechnical conditions is usually not taken into consideration in most vibration standards. This paper describes how building foundations, and in particular mixed foundation types, are especially sensitive to ground vibrations. A method is presented for assessing the risk of settlement due to vibrations in granular soils. Also, a simple concept is proposed for estimating settlements in the vicinity of driven piles.1. INTRODUCTIONUnder unfavorable conditions, the installation of piles or sheet piles can cause damage to buildings or other structures on the ground. Frequently, such damage is attributed to vibrations of the building itself. In many countries, national or international standards are used to assess the risk of vibration damage to buildings. As such standards are often prepared by engineers with little or no geotechnical knowledge, the effects of ground conditions on vibration propagation and damage to building foundations are generally not recognized, and damage criteria based solely on the dynamic response of buildings neglect the importance of damage mechanisms governed by geotechnical conditions. One potentially important damage mechanism is differential settlement below buildings, especially when these are founded on loose granular soils. When seeking guidance in the literature, little or no information can be found regarding methods to assess permissible levels of ground vibrations with respect to risk for settlement.This paper focuses on building damage that can be attributed to foundation conditions. In the case of ground vibrations due to pile and sheet pile driving, differential settlements are of particular importance as the ground vibrations attenuate relatively rapidly from the source. Consequently, settlement below part of the building, which is located close to the vibration source, can be significantly larger than at a distance further away.Piles are often a cost-effective foundation solution for buildings on loose and compressible soil, frequently located in urbanized areas. Sheet piles are commonly used as support for deep excavations. While impact driving is most commonly used to install piles, vibrators are frequently used for driving (and extraction) of sheet piles. It is important to recognize the fundamental differences between impact and vibratory driving. During impact driving, the pile is subjected to stress waves of short duration. The driving process creates vibrations, which radiate from the shaft and/or the toe of the pile into the soil. The larger the intensity of the stress wave, the larger the dynamic force and the intensity of ground vibrations. In addition to the vibration intensity, which often is expressed in terms of particle velocity, also the vibration frequency is important. When the dominant frequencies of the generated vibrations harmonize with the resonance frequency of buildings or building elements, the risk of building damage increases."

Jan 1, 2014

By James E. Maccariella

Replacement of an existing movable bridge with a new low level fixed bridge would not accommodate potential future navigation traffic. In order to replace the existing bridge in a cost effective manner, while accommodating the potential future needs of the Port of Salem, a new bridge was proposed that would permit conversion to a vertical lift type movable bridge should a potential need for upstream navigation warrant such a project in the future. Drilled shafts were found to be the most desirable foundation type for the replacement of the Route 49 Bridge over Salem River. Their ability to resist scour, be constructed without cofferdams, adequately resist vessel collision forces, and accommodate conversion to a future vertical lift bridge allowed the project to meet both the needs of the New Jersey Department of Transportation and the Port of Salem.

Jan 1, 2005

By Jelke Dijkstra

This paper presents the results of model pile load tests in a photoelastic material. The soil in this test is represented by an assembly of photoelastically sensitive glass particles, which allows for optical measurements of stresses. In the same test setup, displacements around the pile are measured using digital image correlation (DIC). During the pile installation stresses and strains are recorded. Tests were performed in loose and medium dense particle assemblies. The development of stresses and strains around the pile tip and pile shaft are quantified and presented in this paper. For the loose conditions the results show a small influence on the stress state. For the medium dense conditions a clear stress change is observed.

Jan 1, 2006

By Scott D. Thomson

The client for this project specializes in the use of state-of-the-art technology to fabricate and assemble composites and metal-bonded structures for commercial and military aircraft programs. One of the key components for this operation at the client's plant is a highly precise computer-numerical-controlled router known as the Shoda Machine. This machine tool was installed at the plant in July 1998 for the manufacture and inspection of aircraft parts, and it is extremely sensitive to deflections. To monitor the occurrence of deflections, an internal laser system continuously checks the machine calibration. Deflections in excess of 5/1000-inch in the foundation on which the machine rests require costly periodic re-leveling and recalibration of this tool. Therefore, a significant problem arose when measured deflections during machine operation were as large as 20/1000-inch. In addition, the foundation was cracked in at least three places as a result of elastic foundation movement caused by dynamic loading as well as shrinkage and loss of base support. Deciding on a remediation procedure to alleviate or eliminate these problems involved the following important considerations: (1) achieving the client's need for reducing deflections to less than 5/1000-inch, (2) minimizing the repair cost as much as possible, and (3) reducing the time required for implementation of the foundation remediation solution. After evaluating the advantages and disadvantages of several alternatives, jet grouting was selected as the most suitable solution. The jet grouting program provided columnar elements of soilcrete to remediate the Shoda Machine foundation.

Jan 1, 2003

By George Mylonakis

The curvatures and subsequent bending imposed to piles by the surrounding soil during the passage of strong seismic waves is studied. This type of bending develops even in the absence of a superstructure and is referred to as "kinematic bending", to distinguish it from bending imposed to piles by loads generated from the inertia of the superstructure ("inertial bending"). Although kinematic loading may be severe in the presence of sharp stiffness discontinuities in the profile and may lead to damage, it has received little attention by engineers. The scope of the paper is twofold: (i) to discuss some fundamental aspects of seismic pile bending, and (ii) to review some existing design methods. To this end, a dimensionless bending strain parameter (instead of the more commonly used bending moment), and a strain transmissibility function relating pile bending strain and corresponding soil shear strain are introduced. Numerical examples are also presented.

Jan 1, 2002