Search Documents

By James A. Schneider

The successful installation of long piles driven into very dense sands relies on the occurrence of the reduction in local friction with increased pile embedment, a phenomenon known as ?friction fatigue?. The underlying mechanisms controlling friction fatigue are poorly understood, with some design methods including an adjustment for the influence of pile diameter while others do not. This paper back calculates the installation resistance of 0.356m to 2m (14in to 78in) diameter open ended piles driven into very dense sands using wave equation analyses. Cone penetration test data are used to link soil properties to installation resistance. The study illustrates consistent interpretation of a variety of case histories of open ended piles driven in very dense sands using newly developed analysis techniques and normalized parameters. Results provide information on methods for incorporating friction fatigue into drivability studies as well as a discussion of mechanisms related to pipe pile installation resistance in sandy soils.

Jan 1, 2010

By George Piscsalko

There are numerous methods currently available to assess the integrity of drilled shaft and ACIP piles. Each method has its advantages and limitations. This paper will compare the various available methods as well as introduce a new method for assessing integrity of drilled shafts and ACIP piles. This new method, known as Thermal Integrity Profiling, determines the integrity of the shaft both inside and outside the reinforcing cage by measuring the hydration temperature of the concrete along the length of the shaft. These temperature measurements can be made by either passing a thermal probe through a standard Cross Hole access tube, or from embedding thermal wires within the shaft. This Thermal Integrity Profile method will be described in detail and one case history will be presented. Additional testing methods which will be compared include low strain Pile Integrity Testing and Cross Hole Sonic Logging. Advantages and limitations for each method will be discussed.

Jan 1, 2011

By Bauduin C. Besix

The Eurocode 7 "Geotechnical Design" is based on "Limit State Design", tackling the uncertainties as much as possible at their source through: - selection of characteristic values of variables (loads, soil properties, pile resistance,...); - partial factors applied on the characteristic values; - model factors to account explicitly for uncertainties of the calculation rule if necessary. Eurocode 7 will propose three "design approaches". The selection of one of them will be by National Determination. For pile design, the approaches are: - approach 1 is a "material factoring approach" at load side and a "resistance factoring approach" at resistance side. The structural and geotechnical design are checked for both of two separate sets of partial factors. - approach 2 is a "load and resistance factoring approach" and is in several aspects close to a deterministic approach. The design is checked for one set of partial factors. - approach 3 is a material factoring approach, at load as well as at resistance side. The design is checked for one set of factors. The aim of this paper is to introduce to the design of pile foundations based on pile load tests and on ground test results (semi-empirical and analytical methods) in the frame-work of the three design approaches. Detailed attention is devoted to: - the selection of the characteristic value of the pile resistance, accounting for spatial variability and stiffness of the structure; - the reliability of the prediction of the pile resistance using analytical or semi-empirical methods which may be accounted for through a "model factor". The results of a large test campaign on screw piles in OC Clay and a calculation example illustrate the proposed procedure when calculation rules using CPT results are used.

Jan 1, 2002

Jan 1, 1989

By Arturo Ressi di Cervia

From the times when men in lacustrine environments drove wooden piles into the mud to elevate their dwellings, until the beginning of the twentieth century builders reacted to the conditions found in the location of their proposed structures by attempting to distribute their loads in ways that could be supported by the foundation's soils; or, if those were unsuitable, by moving the structure, whenever possible. While many major structures were built on stable ground (the pyramids were founded on rock), others were built on [ ]

Jan 1, 2000

By Carl-John Grävare

This paper deals with some of the systems and equipment that are being developed and/or are in use in Scandinavia. The main subject is the development of loading tests on the piles using monitoring equipment. This paper also describes ground improvement using lime-cement columns, expander body piles and steel core piles.

Jan 1, 2000

By Z. G. Lin

In Xian, China, compaction by means of soil (or lime-soil) piles is one of the effective methods widely used for densifying loess and eliminating its collapsibility. However, as a result of groundwater table rising, it is no longer applicable in many areas. This paper is the summary of the first-time use in Xian of sand-gravel compaction piles aimed at densifying the miscellaneous fill (already partially under water) and saturated loess at a certain project site. In-situ tests, conducted before and after the treatment and including several kinds of penetration tests backed up and confirmed by a set of plate loading tests, yielded very satisfactory results, strongly testifying to the viability of the method.

Jan 1, 2010

By Robb L. Swenson

Construction of foundations for the Skyway Segment of the San Francisco Oakland Bay Bridge required innovative techniques due to the mass of the structures being inserted and the unique subsurface of the Bay. Twenty of the pier structures required large sheet pile cofferdams. Eight other foundations were installed in open water without cofferdams at the deeper part of the Bay. This narrative will present the initial planning, as well as the stages of installation, for each type of foundation. The first section will discuss foundation constructability modifications made during the initial planning phases of the project. Considerable effort was expended by Caltrans, the owner, T.Y. Lin the designer, and KFM (Kiewit/FCI/Manson) the contractor in modifying the design to assure that required tolerance would be maintained during the installation of the foundations. The final section will describe the steps required for installation including: initial access dredging, installation of cofferdams, preparation required to install the footing boxes, footing box installation, foundation support pile installation, and pile to box connections.

Jan 1, 2013

By C. Vipulanandan

It is critical to monitor the ground conditions during excavation and drilling of boreholes during construction to identify possible changes in the soil and rock formations. Drilled shafts are increasingly used as foundations to support structures, bridges and other facilities in geomaterials such as soft-rocks and hard clays. Locating the bottom of the borehole during construction with the required design strength is critical. Hence developing a simple device that could be easily adapted/used with the drilling tool was of interest in this study. Determining the shear strength of the geomaterial in the borehole and at various elevations including the bottom of the borehole can lead to better quality control of construction by identifying the various layers based on strength. In this study, a down-hole penetrometer (DHP-CIGMAT) was designed, built, calibrated and tested in the field to determine its effectiveness in measuring the strength of soil/soft rock in the boreholes. Based on limited field tests, linear correlations between geomaterial strengths and DHP-CIGMAT deflection have been developed. The DHP-CIGMAT can be used to identify soils and soft rocks.

By Bengt H. Fellenius

Session 2, Deep Foundation without Soil Excavation, has attracted no fewer than 22 papers dealing with subjects from soil improvement by grouting, injection, and deep mixing techniques through vibroflotation and special piles, including aspects pertaining to conventional driven and bored piles. In the short time available, it is not possible to both do justice to the papers and provide a critical review of the state-of-the-art. Instead, to meet the objective of making the next half hour worthwhile to the audience, I have chosen to comment on a few special points brought forward in the papers and thereafter to discuss more in detail a couple of aspects I have deemed to be of general interest. Four papers deal with jet-grouting, injection, and deep mixing techniques: DOMSKI, J. J. Reinforcement of subsoil under the foundations of historical buildings in Cracow using deep injection technique. RESTELLI, A. B, BERTERO, M., and LODIGIANI, E. Deep mixing technology to improve the bearing capacity of a very soft clayey soil under an earth embankment.

Jan 1, 1994

By A. J. Partos

One Liberty Place, at 315 m is the tallest building in Philadelphia, PA USA. It is supported on drilled piers socketed in heterogeneous rock. 3832 kN/m2 end bearing and 383 to 766 kN/m2 shaft resistances were selected. Design load distribution was 40% on the base and 60% by shaft resistance. The maximum compression on the corner core columns is supported by clusters of 3 drilled piers. In order to confirm load distributions along shaft and at the base, Drilled Pier G-10 supporting T13-A type outrigger column was instrumented. This column supports 53,849 kN compressive load which includes 13,440 kN windload. This paper reveals details about the process to select the final design for One Liberty Place together with pertinent Information about site geology, foundation construction, quality control, and methods of steel erection. It also presents detailed Information on the type of Instruments, their calibrations, field fabrication, and installation in the shaft of Pier G-10. Readings of concrete temperatures, computed loads, and load distributions are presented for a period from October 1985 through May 1988. The building was completed in 1987.

Jan 1, 1989

By M. Hesham El Naggar, Yasser Abdelghany

"ABSTRACT: The axial and lateral monotonic and cyclic behavior of helical pile foundations was investigated and new innovative helical screw systems suitable for seismic loadings were developed and patented. More than one hundred full scale field load tests were conducted on instrumented helical screw piles installed in cohesive soil. The piles included: plain helical screw piles (P-HSP); grouted (G-HSPs); fiber reinforced polymer FRP-G-HSPs; and reinforced grouted RG-HSPs. The RG-HSP piles axial capacity was more than twice that for P-HSP, with minimal reduction after cyclic loading, and their lateral capacity was more than 3 times the P-HSPs capacity. A 3-D finite element model was established. The results of 3-D finite element modeling were used to establish the load transfer mechanism and a design methodology for the considered piles.INTRODUCTION AND LITERATURE REVIEWHelical (screw) anchors have been utilized in tension loading and have gained popularity for bearing load applications. Helical piles represent an overall cost effective alternative to conventional piles for new construction and repair applications. The helical piles speed and ease of installation, less noise during installation added advantage with regards to their efficiency and reliability for underpinning including re-support and reconstruction of distressed and damaged foundations for either stabilization or rehabilitation. The “square shaft” SS175 pile is a segmented deep foundation system with helical steel bearing plates (helices) welded to a central steel shaft. Load is transferred from the shaft to the surrounding soil through these bearing plates. Segments or sections are joined with bolted couplings. Practically installed depth is limited only by soil resistance and economics. A helical bearing plate or helix is one pitch of a screw thread. All helices regardless of their diameter have a standard 75 mm pitch (Figure.1). The performance of single helical anchors and group action were studied experimentally and theoretically by several researchers, the researches focuses on the installation torque and uplift resistance. Some researches focus on the load carrying capacity with little pile response to cyclic loading effects or to instrumented full scale field testing. Helical piles axial compressive or lateral loading still is not well characterized and needs more analyses and their seismic performance was not investigated. For such this research was initiated to investigate the helical piles monotonic and cyclic performances under axial and lateral loadings to consider their usage in different applications in seismic zones. Among the several researchers, Clemence (1983); Mooney et al. (1985) conducted field and laboratory testing; Hoyt (1989), Hoyt et al. (1995), and Ghaly and Clemence (1998) conducted theoretical and experimental testing, Puri and Vijay (1984), Huang et al. (1995), Perko (2000), and Pack (2000) conducted theoretical analyses. Rao and Prasad (1993), Prasad and Rao (1994), conducted experimental testing; Vickars and Clemence (2000) studied the performance of helical piles with grouted shafts."

Jan 1, 2014

By K. Rambha Devi

The paper is an attempt to co-relate the findings of pile capacity using a number of formula suggested by various authors with the actual field load test results. Five locations consisting of wholly sandy or clayey soils were selected for this purpose. The clayey soils are on a hilly area having clays of medium to stiff consistency upto a depth of 20 m The sandy soils are near the bank of a river having angle of internal friction 'Ø' value ranging from 30 to 35 Degree. The details of the soil properties are given in Table-1 Bored cast-in-situ piles of 30 cm diameter and a length varies from 6.5 m to 13 m were designed and cast for load test to be carried out. The load applied was twice the design load. The load vs settlement curves were obtained. The theoritical values obtained by formula suggested by various authors were superimposed on the curves. From the careful study of these curves it is seen that De Ruiter and Berigen values are close to the actual results for clayey soil. For sandy soil it is found that both the BIS method and Meyerhof method found to give conservative resuslts. A multiplication factor is suggested to theoritical values for obtaining satisfactory results.

Jan 1, 1996

By K. Mallikarjuna Rao

There are several methods available to estimate deflection and ultimate Capacity of laterally loaded piles. In this investigation an attempt has been made to verify the existing methods for prediction of ultimate lateral resistance and deflection with the laboratory and field test results reported in the literature. A 75 pile loading test data obtained from the literature was used to evaluate two methods designed to predict the ultimate lateral resistance of rigid piles and three methods designed to predict the lateral deflections of rigid piles and four methods designed to predict the lateral deflection of flexible piles subjected to lateral loads. The accuracy and precision of each method is quantified statistically. The statistical results of the overall analysis indicate that the mean values of the ratios of predicted to measured lateral capacities vary from 0.62 to 1.14 with an average of 0.88. However, the settlement predictions were much more widely scattered than the ultimate load predictions and in general all the methods have a tendency to under predict the deflections. A new method is proposed by modifying the Broms's method to estimate the lateral deflections of free headed rigid and flexible piles separately. The proposed modified methods were found to be reasonably good in comparison to existing methods and to overestimate deflections.

Jan 1, 1996

By Rudolph P. Frizzi

Quality control is essential for augered cast-in-place (ACIP) piles (also known as continuous flight auger (CFA) piles outside the United States) and drilled displacement (DD) piles since the pile is constructed below the ground surface out of the direct sight of the personnel constructing and inspecting the pile. ACIP piles are being successfully constructed to support high-rise structures, hospitals, arenas and stadiums, mass transit systems, and power and industrial facilities. The use of DD pile technology is also gaining ground in the United States, typically utilizing proprietary systems such as Omega (currently utilized by Richard Goettle Inc., and LG Barcus and Sons, Inc.), Berkel, and DeWal (currently utilized by Morris-Shea). Different types of ACIP/DD pile installation equipment are shown in Figures 1 and 2. ACIP piles are installed into granular and cohesive soils, and soft rock to lengths currently approaching 130 ft (39.5 m), with diameters up to 24 to 36 inches (610 to 915 mm), and sustaining design loads approaching 900 kips (4000 kN). Current DD pile installation equipment in the United States is capable of installing up to 79-ft-long (24 m) piles with diameters ranging from 12 to 18 inches (305 mm to 460 mm).

Jan 1, 2004

By John E. Lens

Minutes after the Friday afternoon October 16, 2009 announcement that the 80 year old Lake Champlain Bridge was closed to traffic out of concern for public safety, emergency detour planning started at VTrans and NYSDoT. The closure severed a cross-lake link between Addison, VT and Crown Point, NY, which created a 76 mile detour and significant hardship for commuters, farmers working on both sides of Lake Champlain, and businesses relying on both traffic and employees commuting between Vermont and New York. Rehabilitating the bridge was determined to be economically and technically unfeasible and the design of a replacement bridge was accelerated for a spring 2010 construction start. In the meantime, a temporary ferry alternative was to be rushed into service beside the original bridge by February 2, 2010. This paper presents the case history of the fast-tracked ferry dock design and construction on the Vermont side. Twin 300-foot-long pile supported approach spans, a loading slip system and ice deflectors were designed, fabricated and constructed in 90 days in the fall/winter of 2009-2010. This chronicles the project from initial concepts through the extraordinary cooperation between state and federal agencies, and near round-the-clock winter construction on Lake Champlain. This project and its companion project on the New York shore succeeded by virtue of exceptional cooperation between seasoned regulatory, design, and construction participants and warrant this case-history presentation of the Vermont project to share within the industry as an example of overcoming extraordinary challenges.

Jan 1, 2011

By Marco D. Boscardin

Control and mitigation of building response to construction activities are assuming a greater role in design decisions for underground construction. Alternatives for controlling building response have multiplied with the continued development of ground modification methods, better control of construction activities that cause ground movements, and increased understanding of building behavior and response. This paper describes approaches to estimating building response to construction-related ground displacements caused by adjacent excavation and highlights the discussion with several case history examples. Examples discussed includes experiences with two, seven-story historic structures, supported by timber piles with granite block pile caps, which were underpinned in preparation for ground-freezing ground stabilization and tunnel construction beneath the buildings. The elevation of each building column was monitored and elevation adjustments were actively performed during construction. The second example examines the performance of a slurry wall braced cut, 45 to 50 feet deep penetrating through a stiff crust into a soft clay layer and associated building response. This cut was immediately adjacent to two, approximately 15-story office buildings, which were supported by deep foundations founded in the stiff crust.

Jan 1, 2003

By Jiwei Duan

The energy transferred from a hammer to the pile top is considered as the effective energy in this paper. The effective energy is related to the pile dimensions, soil and pile-soil interface properties. This relation may be expressed as an equation based on the dimensionless theory. The relationship between pile capacity and effective energy was studied by performing a series of wave equation analyses using a commercial software called GRLWEAP (Wave Equation Analysis Program) by GRL Engineers, Inc. The results show that the pile capacity increases with the blow count when the effective energy is constant, however, it has a little change as the blow count is over 100 blows per foot. The pile capacity decreases as the ratio of pile penetration depth to pile diameter increases if the effective energy is constant. The pile capacity will increase as the pile diameter and wall thickness increases if the effective energy is constant. The pile stickout (pile length above the ground surface) does not have a significant effect on the effective energy and may be neglected. Curves for pile capacity versus effective energy are presented to be used for preliminary hammer selection according to effective energy and hammer efficiency. Finally, a case from PDA testing was studied. Measurements of the effective energy and pile capacity by CAPWAP were presented and compared with the results by GRLWEAP.

Jan 1, 2006

By Thomas M. Gurtowski

This paper presents a summary of allowable bearing pressures and skin friction values that have been used to design drilled pier foundations for support of high-rise structures in downtown Seattle, Washington. These design parameters are based upon a review of geotechnical reports and records of more than 20 building projects. The following pages present a description of the soils encountered at these sites including foundation bearings soils, and design bearing and friction values. The accumulated data is summarized in Table 1, and the locations of the buildings are shown in Figure 1. A detailed description of the construction of two belled drilled piers are presented illustrating typical methods and procedures used in downtown Seattle. The two cases are from the Washington State Convention and Trade Center (WSC&TC). SEATTLE AREA SOILS The Puget Sound area was subjected to several major glaciations during the Pleistocene Epoch. Glacial ice originated in the cordilleran and coastal mountains and the Vancouver Range of British Columbia. The maximum southward advance of ice reached the area about halfway between Olympia and Centralia. As a result of these glaciations, the Puget Lowland was filled to significant depths by glacial and non-glacial sediments during the Pleistocene.

Jan 1, 1990

By K. Englehardt

J BERESFORD introduced the subject of the paper which is the use of polymeric slurries to support the sides of diaphragm wall and bored pile excavations during construction. In the opinion of the authors the use of a suitable polymeric fluid offers financial and technical advantages compared with traditional bentonite based slurries. Under quiescent conditions a support slurry must have the following properties. - sufficient viscosity to support the sides of the excavation, to prevent infiltration into soils and to hold loose soil particles in suspension. - when agitated it should thin quickly to assist pumping transfer and cleaning and allow free passage of the grab or drill. - viscosity should be low enough during concreting to facilitate placement but high enough to prevent contamination of the concrete.

Jan 1, 1991