Search Documents

By Cory G. Rice

A significant portion of the piling industry has long felt relying on soil setup to gain the required capacity is a complexity that would rather not be dealt with. Instead, the pile are driven to the required capacity on the initial drive and the potential gain of capacity due to soil setup is simply considered an added bonus or safety factor. There appears to be an attitude that if one did not put in the energy required to develop the full capacity on the initial drive, then one should not expect to gain anything from Mother Nature for free. However, substantial savings in time and materials can be realized by properly accounting for setup. This paper will show the impacts and ramifications this rationale can have on required labor and material costs and illustrate a case history with significant soil setup and the savings realized on a project currently being constructed.

Jan 1, 1992

By M. Kumaran, A. Vetriselvan, A. Purantharan

"This paper presents a case history of evaluating the stability of a distressed earth bund and rectification measures carried out. A 5.45 km long, 7m high earth bund for drinking water storage was constructed in Andhra Pradesh. During construction of the bund following were observed – (a) a longitudinal crack at the downstream side (b) Bund on the downstream side along the crack settled to a max of 700 mm and (c) downstream rock toe level area raised by heave up to 175 mm. Investigation of the events made important contributions to the fundamental understanding of the behaviour of large earthworks of this type. It was found that the variation in subsoil strata was not addressed during the execution.After careful evaluation, stone columns were recommended as a suitable ground improvement technique. Stone columns were used as a reinforcement to improve the shearing resistance of foundation and in turn ensure stability. By using and applying advanced geotechnical engineering analysis tools and modelling techniques, earth bund and its foundation was analysed and examined against failure by slope instability. Stone column design was carried out using in-house computer program GEOSTONECOL and stability of earth bund was analysed using TALREN software. Earth bund construction was completed after ground improvement and is performing satisfactorily.INTRODUCTIONIn order to supply water during summer season, Government of Andhra Pradesh decided to construct a 7m high and 5.45km long earth bund summer storage tank. It was one of the largest earth bund summer storage tanks in whole of South India at the time of its construction. During construction, the earth bund has undergone sudden distresses. Investigation of the series of events occurred during construction has made important contributions to the fundamental understanding of the behaviour of large earthworks of this type. This paper presents the reasons for earth bund failure, slope stability assessment of the distressed earth bund and recommendation of stone column as a suitable ground improvement remediation technique.DESCRIPTION OF STUDY SITEThe characteristics of the original construction are briefly described as follows. A shallow cut-off trench was excavated below existing ground level at the centreline of bund as shown in Fig. 1. Below the base of the trench a cut-off grout curtain was installed. Upstream and downstream shell earth filling was carried out using Clayey Sand ‘SC’ type soil. At some locations, bottom of cut-off trench has reached as deep as 12m from the existing ground level."

Jan 1, 2017

By Marlion T. McQuinn

This paper will discuss the design, construction, and performance of the support of excavation on the Dulles East and West Automated People Mover Tunnels and Station projects. The elements of the system included drilled soil nails and rock anchors with reinforced shotcrete to the excavated face. We will discuss the geotechnical characteristics, design and construction considerations, loading criteria, construction techniques, schedule constraints, and performance of the support of excavation system. In consideration of the conference theme, there will be a discussion of the application of the real-time instrumentation monitoring program. The project team worked to design and install approximately 710,000 square feet of shotcrete and 19,000 soil nails/rock anchors as well as excavate over 720,000 cubic yards of rock materials within 15 months and in such a manner as to minimize the disruption to airport passengers and operations.

Jan 1, 2006

By Peter Yen

This session consists of five papers. Three involved research on the properties of grout materials, specifically ultrafine cements and polyurethane grouts. Two papers present the development of soil grouting technology and monitoring methods. Of great interest are the papers on ultrafine grout penetrability testing focusing on the pressure filtration effects encountered in permeation grouting applications (Ericksson, Stille and Mittag, Savidis). The comparison testing of hydrophilic and hydrophobic polyurethane grouts submitted by Vrignaud, Ballivy, Perret and Fernagu assessed the long-term performance of these materials for repairing saturated cracks in concrete, subject to thermal expansion and contraction. Two very practical papers present the development of soil grouting, where permeation, fracture, replacement, jetting and other grouting techniques are utilized. The papers by Lees with Chuaqui and Warner present experience with ultrafine and other commonly used grout materials. Methods to measure and monitor the injection process and verify production progress are discussed.

Feb 10, 2003

By Maurice Bottiau

The recent evolution of the piling market clearly shows a growing demand for screw piles with soil displacement. The recently developed Omega Screw pile ful-fill these new expectations, combining the advantages of vibration-free systems and the behaviour of a displacement pile. The paper describes recent experience and new applications with this very promissing pile. Full-scale load tests were carried out in different countries as U.K. or Sweden. A very attractive and innovative piled embankment is also described, using geogrids in order to transfer the loads from the superstructure to non-reinforced Omega-piles.

Jan 1, 1996

By Jörn M. Seitz

Dynamic load testing is employed with ever increasing frequency to estimate the strength and elastic settlement behavior of piles of all types. For dynamic loading ram masses up to 20 Mg have been used and pile resistance forces up to 30 MN have been activated. Strains and accelerations induced by the impact are measured near the pile top and a load-set curve is computed by the so-called CAPWAP method. This paper briefly describes both the necessary equipment and other details of the dynamic tests and the available analytical tools for data interpretation. Furthermore the need for further research and the current status of standardization will be discussed. This paper also presents the results from several static and dynamic correlation tests on cast-in-situ piles of up to 2 m diameter and 64 m length. The results demonstrate the economical and technical feasibility of this test method.

Jan 1, 1987

By Charbel Khoury, Kwabena Ofori-Awuah, Kofi B. Acheampong

"Following heavy rains in spring of 2014, Prince George’s County officials issued a mandatory evacuation for homes in the Piscataway Hills subdivision of Fort Washington, Maryland where a landslide along a 1700-foot hillside destabilized homes, collapsed the single access road, and resulted in water and sewer mains break. Forensic investigations, including geologic assessments, test borings and in-situ Cone Penetrometer and Dilatometer soundings, were performed to evaluate subsurface conditions and provide stabilization options for the roadway and slopes. Post-failure ground movements were monitored using inclinometers. Critical failure planes were identified within the underlying 30-foot thick Marlboro Clay formation, a known geologic hazard with historic occurrences of landslides and slope failures.This paper discusses the remedial design for stabilizing the landslide and 60-foot hillside slope failure, and protecting the roadway. Amongst several feasible options, driven piles were selected in consultation with the County and retained contractor based on cost, environmental impacts and site constraints. Constraints included private ownership of hillside slope, upslope buildings safety; deep-seated failure, relocation of underground water and sewer mains, and accelerated construction schedule.Pile design included global slope stability analyses and lateral pile analyses using several loading configurations to optimize pile geometry and spacing, and determine a value-engineered design satisfying both serviceability and strength limit states to achieve long-term stability with factor of safety of 1.3. Soils within the active landslide plane were assumed to provide no resistance, while soils below the failure plane provided lateral resistance. This stabilization scheme, which extended along the 1700-foot roadway section and toe of hillside slope area, consisted of 410 steel HP16x141 piles in two to three rows driven to depths between 60 and 70 feet below the Marlboro Clay stratum at 5 to 7-foot spacing."

Jan 1, 2017

By David E. Thompson

This paper describes the full-scale field load testing of three deep foundation units using the Osterberg Load Cell. The load tests were completed on three separate projects, two in Massachusetts and one in New York. The Massachusetts projects involved the load testing of two 18-inch O.D. concrete-filled steel pipe piles over water for railroad bridge reconstruction projects in Revere and Saugus/Lynn. The New York project involved the load testing of a 24-inch diameter drilled shaft socketed into sandstone on land for a building foundation in Rochester. The 18-inch O.D. piles were loaded to failure at jack pressures of 142 to 215 tons. The drilled shaft was loaded to failure at jack pressures of approximately 450 tons. The loading testing procedure is described and the results of the three tests are presented. The advantages and disadvantages of the Osterberg load cell for load testing of deep foundations are discussed.

Jan 1, 1989

This Workshop was held at the Doubletree Inn, Seattle, Washington from September 26 to 28, 1997. Run under the auspices of the Deep Foundations Institute (DFI), it was co-funded by the newly formed Japanese Association of Micropiles (JAMP), and the Federal Highway Administration (FHWA). The Workshop was jointly organized and facilitated by Fujita Research Corporation and ECO Geosystems, Inc., with close support by Donald B. Murphy Contractors, Inc. DFI kindly consented to publish these Proceedings. As is clear from the list of attendees, 42 specially invited engineers from all aspects of micropile technology were present, representing Japanese, European and American practice. This proved to be a most friendly and interactive group of people, who freely exchanged ideas, views and close comradeship, not only during the technical sessions, but (and especially!) during the numerous social events. Perhaps the best illustration of this came in Day 2 when the attendees were divided into five competing teams, each comprising representatives from the different geographic groupings. These teams had to quickly devise solutions to two technical problems (using standard data previously provided. A team of "referees" (who also acted as "coaches") later determined the most apposite response, based on constructability design concept, cost, schedule and so on. Not only were the winning team very liberal in distributing the prize (vintage California champagne) among themselves, but the whole Workshop soon benefited from their generous division of the spoils of victory.

Jan 1, 1997

Jan 1, 2005

By Don Deardorff, Ke Yang, Yingcai Han, Ken Sorensen, Robert Kruger, Mark Petersen, Diane Fiorelli, Larry Goldfarb, Kathryn Petek, Kwabena Ofori-Awuah

Design of deep foundations for lateral loads requires an understanding of soil-foundation-structure response during loading. Lateral loads on a deep foundation (piles) could be due to earthquakes, winds, waves, and/or machine vibrations. Over the years, analysis of response of piles due to lateral loads evolved from closed-form solutions to p-y methods to strain wedge to finite element/finite difference modeling. Although analysis of lateral response of piles and shafts is routinely performed, there is no single guidance document and/or standard for design and testing. Several different analytical methods are available for the analysis, and the resulting design can result in significantly different responses which can create confusion. This is especially true for analyzing and designing piles in potentially liquefiable soils with lateral spread issues under seismic conditions.This guidance document is intended to assist geotechnical engineers, pile designers, and contractors in analysis, design, and testing of piles and drilled shafts for lateral loads. This document discusses the background of different analytical and testing procedures and presents the recommended methods for analysis, design and testing of piles for lateral loads.Chapter 1 defines the different kinds of lateral loads to which a single pile or pile group may be subjected. This first chapter also presents different types of piles used to resist lateral loads.Chapter 2 discusses geotechnical issues related to lateral pile design such as liquefaction and lateral spreading and other non-seismic issues. Also addressed in Chapter 2 is geotechnical site characterization (as related to lateral loads) in terms of site investigation, in-situ testing, geophysical testing, laboratory testing, and estimation of soil/rock properties.Chapter 3 discusses the background and available analytical methods and tools for the analysis and design of single piles and drilled shafts. Several methods of analyses from closed-form elastic solutions to the finite element/finite difference solutions and their applicability are discussed. Available commercial computer software packages for analyzing single piles and drilled shafts are also presented.Chapter 4 expands the discussion of single piles and drilled shafts into the analysis and design of pile groups. In addition, group effects, resistance of pile caps, results of previous experimental and analytical studies, and available analysis tools and software for pile groups are discussed.Chapter 5 presents the issue of lateral resistance of piles and drilled shafts as discussed in different national and international building and non-building codes. A summary of extensive research on several codes are presented to facilitate the compliance with different codes.Chapter 6 discusses structural design issues of individual piles and drilled shafts such as depth of fixity.Chapter 7 discusses soil structure interaction issues related to kinematic and inertial effects due to seismic loading and available methods of analyses.Chapter 8 discusses and presents the typical procedures for the lateral load testing of piles. This guideline was developed as an aid to the practicing engineer in providing information, direction and commentary on the lateral design of deep foundations. Although all reasonable effort has been made to accurately compile the material and information contained herein, no warranty is made with regard to any such material or information and the Deep Foundation Institute assumes no responsibility for any possible errors or any direct or indirect result of the use of any such material or information. It is not intended that this document address every factor affecting lateral design for every situation. Therefore it is the responsibility of the person utilizing information from this document to confirm that it is appropriate and correct for their situation as well as to understand and properly apply

Jan 1, 2012

By Dennis Nottingham

Spin-fin pipe piles can develop large loads in tension, thus have evolved as a foundation product of great potential. Currently, over 500 spin-fin piles have been used successfully in dolphins, docks, buildings and bulkheads. Spin-fin piles are pipe piles with plates welded near the tip at a batter-in-screw fashion. Thus, as the pile is driven, the pile screws into position. Tests show this pile type to have highly unusual stress/strain relationships, wherein plunging failure is usually never reached either at normal or large deformations. Tension capacity can approach pile capacity in bearing; thus, large reserves are usually available for tension. Tests have been performed on 8-5/8-inch to 24-inch-diameter piles in silt, sand, and gravelly soil, to provide a broad spectrum of data.

Jan 1, 1990

By B. H. Moore

The opportunity to evaluate the pile design procedures used on a major project is an infrequent occurrence. It is even more infrequent that the project involves piles with significant tension and horizontal capacities. This report synopsizes over twenty years of design and construction experience on just such a major pile founded structure. The philosophy governing foundation design procedures is described and discussed. The order and extent of full scale pile testing are evaluated. Principal points in the specifications are established and their effect on construction progress and claims are noted. The report concludes with recommendations for future projects.

Jan 1, 2010

By Michael A. Knott

Large lateral forces on bridge foundations due to extreme events such as vessel collisions, earthquakes, and wave forces on storm surges during hurricane events are often the controlling design condition for bridge foundations. A review of the American Association of State Highway and Transportation Officials (AASHTO) vessel collision analysis and design codes used in the United States for highway bridges will be presented. The paper includes the background and development of the AASHTO Guide Specification and Commentary for Vessel Collision Design of Highway Bridges (1991) and vessel collision provisions of the AASHTO LRFD Bridge Design Specifications (3rd Edition 2004 and the approved 2005 Interims). Experience in using the AASHTO codes will be discussed and observations on the adequacy and gaps, comparison with the European Standard Code, and recommendations for immediate and long term needs will be presented.

Jan 1, 2013

By Fabio Santillán, Mario Mauro, Raffaella Granata

"This paper presents the utilization of slurry walls methods for the recent remediation of three high hazard active dams in the United States. Tuttle Creek Dam, located in Manhattan, KS, required seismic retrofit. To this extent, transverse shear walls were installed on the downstream slope using self-hardening slurry (SHS) to reinforce the liquefiable foundation soils. Herbert Hoover Dike, located around Lake Okeechobee, FL, is subject to potential failure because of internal erosion, piping and slope instability at high water levels. The innovative use of the hydromill equipment with SHS allowed the successful construction of the cutoff wall through heterogeneous soils and rock. At Bolivar Dam, located in Bolivar, OH, under-seepage negatively affects the structural stability of the dam, and a partial seepage barrier wall is required through the upstream slope of the dam. In this case, the Contractor selected the plastic concrete seepage barrier, excavated by a combination of clamshell and hydromill equipment. The main features of the three projects are summarized in Table 1. IntroductionTuttle Creek Dam was constructed by the U.S. Army Corp of Engineers (USACE) on the Big Blue River in North-East Kansas in the 1950s for flood control. Tuttle Creek Dam is a zoned earthfill embankment, 7,500 ft long and about 137 ft high with a crest width of 50 ft (Fig. 1). It is located in an area of moderate seismicity associated with an old continental rift zone located just to the east of the dam. The USACE, under the Dam Safety and Assurance Program, determined the need for remediation. Site investigations and geotechnical analyses identified the upper alluvial foundation sands as being susceptible to liquefaction when subjected to the Maximum Credible Earthquake.In 2005, USACE awarded a construction-manager-at-risk/early Contractor involvement contract. The USACE and the Contractor closely cooperated to identify the most effective technologies, materials and configurations to be used in the remediation. The original remediation design required both the upstream and downstream slope stabilization of liquefiable foundation. Results of refined seismic deformation analyses revealed that the stabilization of the downstream slope and toe was needed to protect the downstream seepage control system and to provide assurance that a liquefaction-induced flow slide would not occur (Stark et al., 2012)."

Jan 1, 2016

Jan 1, 1992

By Zhou Lu-Jian

The Port of Shekou is situated at Shenzhen Bay on the east bank of Lingding Ocean. Its coastline is about 6 km long and the water depth near the shore is Favourable. Across the bay is the ' New Territories " of Hong Kong. The port is at a distance of 22-23 seamilesaway from center of Hong Kong and 80 seamiles to Huangpu Harbour of Guangzhou, its highway links with Shen-Guang Highay. Since 19 79 China Merchants Group of the Transportation Department, began to set up Shekou Industrial Zone, the port has been developing and flouri­shing in business. With 15 large or small berths in all, the present portline is 2600 m, and the annual cargo throughout is over 3,000,000 tons and the annual passenger traffic is about 2,000,000 persons. Equalling a medium-scale seaport, it has been officially approved as an oceangoing transit port by the ministry of Transportation. The construction of Shekou port is chara-terized by the self-collected funds and the short construction period. In view of this, the optional plan of the port structure must serve the requirements of simplicity in struture, economy in mate­rial and speed in construction. That accounts for the most application of the sheet piling type to the port in Shekou. Once the project was approved, the cons­truction started. Only within an average period of 7-8 months, a deep water pier was completed and put into operation, which covered series of processes from exploration, designing, tender for con­struction to completion.

Jan 1, 1991

By Tony Mazzo

It has often been said by consulting engineers that foundation contractors are in the business of taking risks. One would agree that the mere fact a foundation project can be budgeted, planned, engineered and executed solely on the reliability of eight test borings made at a proposed site having an area of approximately 19,000 square feet, is a risky proposition, in and of itself. Now imagine that this site is actually one half of a city block located in an urban setting in an old, congested, historical neighborhood, surrounded by narrow city streets and historic landmark buildings. And suppose that the required depth of excavation for the construction of the new building on this site is approximately 35 feet and the natural groundwater table is at a depth below existing grade of only 25 feet. Given the difficult site conditions outlined above, one could certainly add the words "challenging" and "complicated" to the inherent word "risky" when describing the construction techniques involved to undertake a foundation project of this magnitude. This case study will discuss in detail how the excavation, sheeting, dewatering and underpinning work was accomplished as well as the problems overcome along the way.

Jan 1, 2003

By Karen C. Armfield, Gisele R. Passalacqua, Joanna Smith

When selecting a solution for improving resiliency at facilities, such as airports, utility and transit sites, there are many options to protect structures and equipment against potential flooding. Each case involves an evaluation of the several key factors such as: design flood parameters, the geography and geological conditions below the site, the facility, and the layout of buildings and equipment to be protected. Upon reviewing these conditions and conducting a cost analysis of various options, the most suitable approach to protecting a facility can be determined. This paper will compare the conditions at various New York City sites, and give detail to the solutions utilized at these sites to improve resiliency and protect each facility. Flood wall types varied as did the strategies for raising critical equipment, to meet the Federal Emergency Management Agency (FEMA) and American Society of Civil Engineers (ASCE) 7 guidelines. Due to granular soil conditions, some sites may experience soil seepage below the flood wall resulting in the need for underground cut off systems. The authors will also present detail regarding the solutions used to control seepage. Various cut off systems will be discussed such as grouting and sheeting, explaining the factors that may impact the choice of systems. Another consideration in flood resiliency is the potential for a buoyancy condition on basement slabs when localized flood barriers are employed on first floor doors and windows. The authors will discuss the potential impacts of this condition on facilities and methods to mitigate this issue. 1. INTRODUCTION New York City is an urban coastal Metropolis with varied geology and low land areas. This includes but is not limited to sandy soils at Coney Island and the John F. Kennedy Airport. Soft marshes are found near Flushing Queens and LaGuardia Airport. Heavy rains and coastal storms caused disruption to daily life and heavily affected the economy of this vibrant City. For instance, in lower Manhattan business was interrupted in the Financial District. Power outage was widespread; commuter trains and subways were stopped and put out of service. Additionally, numerous residential homes were damaged in Coastal Neighborhoods such as the Far Rockaways and Staten Island. 1.1. Superstorm Sandy Flood Statistics On October 29, 2012 Superstorm Sandy impacted numerous facilities in the New York City Metro area. The resulting damage cost New York City more than $42 billion in repair costs. $33 billion was allocated to repair housing and infrastructure, and $9 billion was allocated to protect transit systems1. One of the major issues that impacted the city in terms of its preparedness was the high flood surge. The surge surpassed the former base flood elevation and reached as high as 13.88 feet (above mean lower low water - MLLW) in Battery Park at 9:24pm that evening. Tottenville, Staten Island experienced more damage where the water was recorded at +16 (North America Vertical Datum of 1988 - NAVD88), which is equivalent to 18.7 feet above MLLW (see Fig. 1). Not only was the surge at record levels, the waves in New York Harbor were also at record level where some buoy stations recorded waves of up to 32.5 feet. The City released “A Stronger, More Resilient New York” in June 2013, a plan laid out to rebuild communities impacted by Sandy and improve the resiliency of the infrastructure and buildings in New York City. Figures below help to illustrate the extent of the inundation relative to the projects being discussed.

Jan 1, 2018

By Mario A. Terceros Herrera, Mario Terceros Arce, Antonio Marinucci

A Smart Cell is a closed-type tip post-grouting device that is attached to the bottom of the steel reinforcement cage of a drilled shaft and is used to enhance performance and to reduce uncertainty thereof. Control of the grout is maintained within the device during injection and a uniform stress is imparted across entire base area simultaneously, inducing a pre-mobilization load into the shaft as well as the soil. This paper describes the construction and tip post-grouting of drilled shafts from two bridge projects in the Santa Cruz, Bolivia region along the Paraí River. During the grouting process at each project site, there were noticeable differences in the grouting pressures achieved and responses observed, even within short distances between shafts. For this project, the greater benefit of using the Smart Cells was the reduction of risk and uncertainty of performance due to the highly variable soil conditions. Ultimately, since the response of each shaft was observed during grouting and because a “minimum” value of shaft resistance (i.e., pre-mobilization of load) was measured, there is a greater reliability with the anticipated performance of the shafts when axial loading is eventually applied.