Search Documents

By Y. W. Mou

In order to improve the construction of pile foundations and deep foundations of largo sizes, the paper deals with the method of installing square or rectangular bored-piles for annular foundation as well as large-sized hollow or solid foundation.

Jan 1, 2010

By J. P. Powers

Methods for dewatering and the control of ground water for construction and mining are discussed, including open pumping; predrainage with deep wells, wellpoints or other systems; cutoff or exclusion of water by steel sheet piling, slurry concrete walls and slurry trenching, grouting, ground freezing, compressed air, slurry shields and earth pressure balance shields. Criteria are given for the selection among the methods for a given project. Unwanted side effects of dewatering are listed, with procedures for evaluating and avoiding them, by cutoff or artificial recharge.

Jan 1, 2010

By M. Nomura

This paper describes the results and field measurements of two long-term observation tests and two short-term loading tests to confirm the effectiveness of NF piles in reducing negative skin friction. All the test piles were equipped with strain gauges, allowing measurement of the compressive axial forces in the piles. These test results prove that NF piles are effective in reducing the negative skin friction to an insignificant value. Some examples of the design procedures used in Hong Kong and Japan are also presented.

Jan 1, 2010

By L. Z. Xie

The results of the experimental study on the static behavior of single piles subjected to repeated and reciprocating axial loadings are recommended in this paper. Tests of four full-scale single piles of two different lengths under repeated loading and those under reciprocating loading have been conducted using the slow maintained load test method. All the eight piles were instrumented with strain gages located along the shafts. The study showed that for repeated loads below a certain critical value the total displacement of the pile top approached gradually a constant value. However, any repeated load greater than the critical value resulted a residual displacement per cycle, and that the reciprocating load capacity of a pile was dependent on the ultimate bearing capacity of the pile in tension and both were in the direct ratio.

Jan 1, 2010

By Z. C. Chen

Based on the analysis of load test data of long floating piles in soft soil regions, the expressions of load-transfer function of pile shaft and tip for soft soils are presented in this paper, and the data of cone penetration test are suggested to use for calculating the parameters of load-transfer functions. For the loads of pile within the range of the working load of pile, the estimated pile stiffness by the suggested method in this paper are in satisfactory agreement with the results of load tests. The current Vijayvergiya's method and Satowa's method also are used to calculate pile stiffness in soft soil for comparison.

Jan 1, 2010

By Michel Bustamante

The original Cistercian Lure abbey situated in eastern France and built in the second half of the 16th century, has become nowadays an administrative building. Because it has been founded on poor ground conditions and inadequate foundation scheme, the abbey has suffered severe structural distortion. In 1992 an inspection revealed new extensive damages which led to a general refection together with a foundation underpinning. Micropiling was the selected method. Movements recorded over a period of 6 years after underpinning completion are presented.

Jan 1, 2002

By Ali Bouafia

Five full-scale horizontal loading tests of piles carried out by the LCPC in France are interpreted in order to analyse P-Y load-transfer curves. The experimental piles are either bored or jacked into quite homogenous sandy soils and instrumented by strain gauges for measuring bending moments along the pile. Successive differentiation and integration of bending moment profiles have led to derive respectively lateral soil reaction and displacements then to construct the load-transfer P-Y curves. The initial horizontal lateral reaction modulus was derived from these curves and shows linear variation with depth in accordance with Gibson soils profiles. P-Y curves are validated by back-computation of the pile on the basis de these curves and the horizontal reaction modulus was compared to the recommendations frequently used in pile design practice.

Jan 1, 2002

By Jesús E. Gómez

A recent bridge underpinning project provided a unique opportunity to obtain information on the load-deflection response of 260 hollow-core bar micropiles. All production micropiles were proof-tested to a maximum load of 125 percent of the design load. In addition, four verification tests were performed on sacrificial micropiles to at least two and a half times the design loads. This paper presents the results of the verification and proof tests performed for this project, and provides recommended values for design of hollow core bar micropiles in soils similar to those encountered. This work shows that hollow core bar micropiles provide a significant unit bond capacity in both granular and fine soils, which may be greater than that typically expected in pressure-grouted (Type B) micropiles. The hollow core bar system allows faster installation rates in the soil types encountered than other traditional micropile techniques, and can be installed with relatively simple quality control procedures.

Jan 1, 2007

By D. X. Xu

A pump station was constructed at the food of a steep mountain, very close to a riverside. To protect the pump station from being washed out, and to guarantee the stability of the steep hillside behind the pump station and the safety of the foundation pit when the station was built, cast-in-place R.C. diaphragm walls (Fig. 1) were clesigned in front of and on both sides of the pump station. This wall was 130m long, 0.8m wide and 29m deep. The diaphragm walling on both sides of the pump station served to prevent landslides and to fix anchor piles. The 55m long diaphragm walling in front of the pump station served as a temporary shuttering which kept earth and prevented water from permeating when the pump station was under construction. After the pump station project was finished, static blasting method was used to blow up the wall body which was 10m beneath the ground so that the water from the river could come into the pump station. The remaining wall body below this level was kept to prevent soil from being washed out. [ ]

Jan 1, 2010

By David J. Puller

As part of the value engineering process on a major Design Build highway project, instrumented trial pile load tests were used to achieve savings in cost and time on the foundations for a major river crossing. Two trial piles were tested close to failure load at 25MN. Following the interpretation of the pile load test results which included the determination of the ultimate shaft and base capacity, the mobilisation of the shaft and base resistance with pile displacement, and correlations with vertical effective stress and SPT profile, a revised design methodology was proposed. A 25% enhancement on commonly assumed ultimate shaft friction in Chalk was adopted. In addition a significant reduction in the Factor of Safety on end-bearing capacity generally used was also implemented. The revised design resulted in a significant cost and time saving on the piling operation with the pile length reduced by up to 6m (approx. 20%) for the river piers.

Jan 1, 2002

By Dennis Nottingham

Increased interest in seismic soil liquefaction and preventative soil stabilization sets the stage for improved deep compaction methods using pile driving techniques. In 1971 L.B. Foster Company personnel patented a method of deep compaction using a vibratory pile hammer and pile probe. The technique had some success, but did not produce consistent results and thus found its way to obscurity. Other patents attempted to modify the technique by various probe modifications, but again without measurable improvement from a practical point of view. Solutions to economical deep compaction up to 100-foot depths particularly in saturated granular soils would have a great impact on the construction industry and new bulkhead structures being developed, thus PND was prompted into related research and development. The advent of higher horsepower vibratory hammers, coupled with PND engineers' experiments, observations and measurements, led to an "H" pile probe design which has produced measured soil density improvements up to 250% using SPT "N60" values as a measure. Case histories of two projects involving extensive SPT soil sampling comparative measurements will be discussed along with findings that led to the compaction success. Applications to numerous modern "Open Cell" bulkhead projects will be presented and discussed.

Jan 1, 2004