Search Documents

By R. W. Nice

"For many decades the incidence of a highly active graphite-like ore has plagued the McIntyre mine. This ore acts as a precipitant of the gold complex immediately upon formation of this complex. The gold is subsequently discharged with the tailings.Many different methods have been devised by various researchers all of which proved inapplicable for the McIntyre problem.Recently, McIntyre personnel, through their own research, developed a flowsheet. This circuit should give an overall recovery of 36% which is below the 94% experienced in the mill at present. Therefore, less revenue would arise from treatment of these ores. On the other hand there exists a possibility of more efficient mining methods in some of this ore thus allowing more economic recovery.INTRODUCTION This paper has been prepared to serve two purposes:i) To propose a method of recoverying gold from a sizeable orebody at the McIntyre mine at Schumacher.ii) To summarize and present the many methods suggested to solve a very old but very real mineral dressing problem familiar to the industry as long as cyanidation itself."

Jan 1, 1971

By A. E. Reschke

Optimized mine planning of the Leeville Gold Mine, Nevada, necessitated the requirement for an average of 2540 tpd of high quality cemented rockfill (CRF) in primary stoping blocks and underhand cut and fill workings. To meet this requirement, a number of innovative design features were incorporated into the overall batching plant design. Foremost is the use of a dedicated skip to transfer crushed aggregate from surface down through the ventilation shaft to twin underground storage silos. Also, the use of a high shear colloidal mixer on surface to pre-slurry a cement/flyash binder with pipeline delivery to one of two separate underground CRF mixing stations was incorporated. Finally, the binder and aggregate are combined in a 9 m3 twin shaft compulsory type mixer before loading into teleram trucks for placement.

May 1, 2007

By G. V. Lewis

"INTRODUCTORY REMARKS""I believe we need to communicate as much as possible with the industry. I don't think that we should be a body that just goes around doing dust surveys and writing nasty letters. We should get together on these problems and try and solve them as a group. I've only been with the Department a little over 12 months. I haven't visited all of your plants. I've visited most of the major open pits and I have had a chance to observe a lot of problems that you have encountered and a lot of the problems that you have brought up this morning. I thought the best thing I could do is perhaps mention a few of the approaches to the problems that my superior has suggested to me and we have discussed in the Department, and then perhaps go over a few of the evaluating problems and what we are trying to do with our dust surveys and perhaps ways and means of improving the present setup."""

Jan 1, 1976

By Jennifer Pakula

Productivity improvements in underground mining are becoming harder to find. Most mines quickly identify deficiencies in their processes and then struggle to make productivity gains beyond that plateau. One way to increase productivity in this situation is to modify existing methods of operation. Vale?s Stobie Mine has been in operation since the late 1800?s employing a variety of mining methods. Many mining advances have been incorporated over time. With the advent of mechanized rubber tired equipment, sublevel cave mining was introduced to allow economic extraction of a large low grade area. Additional productivity gains were seen in the sublevel cave area with the introduction of preloading production drill holes. In preloading, the holes are loaded with bulk emulsion ahead of the production cycle and then primed for blasting as needed. The introduction of preloading, although giving the Stobie sublevel cave process an overall productivity gain, saw an increase in oversize due to the collar priming technique employed. Handling oversize material prohibited the operators from handling additional units of optimally sized material. Prepriming, adding detonators at the toe and midcolumn of the production holes during the preloading process, was identified as a change that could reduce the formation of oversize. This paper describes the introduction of prepriming to the sublevel cave mining method and focuses on the process Stobie employees followed to ensure a safe transition to this productivity improvement.

Nov 1, 2011

By Frands Jensen, Erik Eriksson

"Haldor Topsoe’s Wet gas Sulfuric Acid (WSA) technology has been proven in a number of industries converting sulfurous gasses to concentrated sulfuric acid. In the metallurgical sector plants have been delivered handling SO2 gasses from copper, zinc, molybdenum, and lead ore. WSA has high energy efficiency and allows autothermal operation from feed gas strengths as low as 3.0% (volume). Recent variants of the WSA process have been developed that allow very high SO2 conversion efficiencies of over 99.9%. This paper describes the technology, its advantages and industrial achievements.The WSA technology is well suited for production of concentrated sulfuric acid of commercial quality from the sulfur dioxide (SO2) gas that inevitably emerges from the metallurgical processes. Some of the features that make the WSA technology attractive for this application are:- High SO2 conversion rates (up to 99.99%)- High energy efficiency leading to a low autothermal point (~ 3% SO2)- No need for gas cooling and drying to produce concentrated sulfuric acid- No production of waste- Very low cooling water consumptionThis paper describes the WSA process principles and highlights features that make this process attractive for handling SO2 gases."

Jan 1, 2014

By Neri Roux, Ross Gilders, Yemi Oyediran, Leo Cheung

Quest Rare Minerals Ltd. is developing their Strange Lake B Zone REE deposit located in Northern Quebec. An extensive batch bench scale testing program was launched to investigate open circuit rougher flotation performance under different conditions. The objective of the flotation study was to demonstrate the effectiveness of rejecting gangue minerals to flotation tailings while concentrating rare earth elements as well as yttrium, zirconium, and niobium into a concentrate suitable for further hydrometallurgical processing. Mineralization of interest at Strange Lake occurs within peralkaline granite-hosted pegmatites and minor aplite. The REE and high field strength element (HFSE)-bearing phases are hosted primarily in pegmatites as relatively fine-grained phases or pseudomorphs. The gangue phases comprise of quartz, feldspar, amphibole, and pyroxene. Potential ore minerals comprise predominantly of kainosite, gerenite, gadolinite, zircon, pyrochlore, and gittinsite. These complex mineralogical characteristics increase the difficulty for processing and provide a challenge for choosing the correct reagent scheme in rougher flotation. Process options including reverse flotation to reject the gangue minerals and de-sliming prior to the direct rougher flotation were investigated. Optimization trials were conducted using various reagent regimes and under different flotation conditions. Encouraging results were found using a combination of collector reagents supplied by Cytec Canada Inc.

Jan 1, 2014

By C. O. Aksoy

Operating the underground marble quarries effectively, it is important to evaluate the deposit blocks economically which are affected by the suitability of the topography and configuration of bedding. The joint sets within the deposit and the spacing between these discontinuties are also of great importance. In this study, the marble deposits that could be geomechanically eligible for underground excavation have been selected throughout Turkey and these selected reserves have been classified accordingly by Q-Rating System. These classified marble deposits that forms groups of 1,2, and 3 (groups were determined by evaluating the O-rating, topography, quarry situation, cracks, joints etc.) are convenient for this type of production. Nevertheless, when the auxiliary factors (topography, location, production method etc.) regarding the deposit have also been investigated, the most convenient sub-group of deposits (Afyon Tiger Skin, Burdur Beige, Diyarbakir Pink and Mugla White) have emerged. The sizing of the pillars have been performed utilising Bieniawski?s stress profile. The LAMODEL software, developed by National Institute for Occupational Safety and Health (NIOSH), USA and run under the laminated displacement discontinuity method, has been used to size the pillars. This work brings in a novel opportunity to Turkey, in which no underground marble quarry has been attempted up-to-date similar to its several examples in Italy, USA, etc. This study serves as a reference for the marble operators and for the pioneering application of laminated displacement discontinuity method in hard rocks.

Apr 1, 2005

By V. M. Robb, F. Walraven, L. J. Robb

"The old Albert Silver Mine is a polymetallic deposit comprising concentrations of CuPb- Zn-Ag-U-F within a set of sub-parallel quartz-hematite veins which occur within the fine-grained apical phase of the 2050 Ma old A-type Bushveld granites. Mineralization occurs as an early pyritechalcopyrite- arsenopyrite-galena-sphalerite-(argentiferous) tetrahedrite paragenesis followed by a later, more oxidized assemblage comprising chlorite-hematite-fluorite-pitchblende. Accumulation of metals appears to have taken place at the interface between a coarse-grained porphyritic granite and an overlying fine-grained phase: veins occur in the latter and represent leakage of magmatic fluids from the differentiated, water-saturated, subjacent granite.Mineralization processes in the Bushveld granites are believed to be related to long-lived circulation of dominantly magmatic fluids stimulated by the high heat productive capacity of the host rocks. Endo- and exogranitic tin-tungsten and base metal mineralization formed during an evolving hydrothermal system that lasted for several hundred million years, forming innumerable small- to mediumscale polymetallic deposits. At the Albert Silver Mine, unroofmg of the cover sequences at circa 1600 Ma to 1700 Ma resulted in the incursion of lower-temperature, high-f02 meteoric fluids which remobilized the earlier sulfides and introduced the paragenetically late U-F mineralization."

Jan 1, 1994

By J. W. Scott, G. G. R. Falkenberg

"The Syncrude project is an integrated complex designed to mine, extract and upgrade bitumen from the Athabasca tar sands to produce 129,000 barrels per day of synthetic crude oil. This paper provides a brief general description of the location, history and geology of the tar sands and the overall organization and structure of the project. The major emphasis and the bulk of the detail presented deals with the extraction plant; a material handling and mineral processing installation designed to treat 312,000 tons per day of tar sand feed.History of the Tar SandsThe Athabasca tar sand deposit was recorded in 1788 by Peter Pond, however the first serious geological mapping and exploration did not begin until 1915. Little interest was taken in the deposits until the Second World War, when the governments of Canada and Alberta conducted an extensive exploration program. In addition a number of pilot plants were sponsored during the 1940 -1950 decade. The hot water separation process was successfully demonstrated on the pilot plant scale during 1948 -49, and was established commercially in 1967 in the G.C.O.S. plant. The Syncrude plant, due to come on stream in April 1978, also employs the hot water separation process."

Jan 1, 1978

By Alan B. Morrow, William A. Poe

"Minerals processing operations are constantly challenged with improving production rates, yields, energy efficiency and process stability. Advanced Process Control has proven to be an effective tool for improving operations by capturing the full process capabilities consistently. However, the velocity of applying the technology as well as the sustainment of these significant benefits has been hampered by the usability of the software and adaptability of the applications.Some of the new technology developments that improve the usability and adaptability of advanced process control include:• modern and intuitive user interfaces,• customizable models to support unique process behavior,• fast and flexible OPC connection tools,• automated model building,• integration with first principles dynamic models and• improved performance monitoring.This paper will briefly discuss the new technology developments that have improved the usability and adaptability of advanced process control and how this can affect minerals processing operations.In today’s environment, Minerals Processing plant managers continuously face new challenges and requirements including:• higher energy efficiency,• increased run lengths,• reduced product quality variability,• reduced emissions,• higher availability, and• lower operating costsOperating a unit to meet these challenges in real time is not easy for operators and conventional process control systems. However, innovatively using existing technologies in Minerals Processing plants can improve operations on a minute by minute basis and reap significant benefits.Advanced Process Control (APC) can extract the maximum performance benefits from existing equipment while respecting plant operating constraints. Expensive capital projects to upgrade equipment are not always necessary. Advanced Process Control can deliver significant economic benefits by maintaining the plant at its most profitable point as conditions change."

Jan 1, 2016

By Alok Porwal, E. J. M. Carranza, M. Hale

Abstract- Approaches to mineral potential mapping based on weights of evidence generally use binary maps, whereas, real-world geospatial data are mostly multi-class in nature. The consequent reclassification of multi-class maps into binary maps is a simplification that might result in a loss of information. This paper describes results of using multi-class evidential maps in an extended weights-of-evidence model vis-à-vis results of using binary evidential maps in a simple-weights-ofevidence model. The study area in the south-central part of Aravalli province (western India) hosts a number of SEDEX-type base metal deposits in Proterozoic supracrustal rocks. Recognition criteria for base metal deposits were represented as both multi-class and binary evidential maps. The known mineral deposits were divided into two subsets, viz., the training and the validation subsets. The training subset was used to calculate, for the evidential maps, the weights, contrasts, and posterior probabilities and their variances. The distributions of expected frequencies of base metal deposits estimated from the posterior probabilities and the observed frequencies were compared using standard goodness-of-fit tests to verify conditional independence of the input evidential maps. The posterior probabilities from both the models were mapped and interpreted to classify the study area into zones favorable, permissive, and non-permissive for base metal deposit occurrence. As compared to the simple weights-of-evidence model, the extended weights-of-evidence model results in more robust and finely differentiated posterior probabilities in favorable and permissive zones and has a better prediction rate. The results also reveal that the statistical properties of the weights of evidence, the contrasts, and the posterior probabilities are not significantly degenerated by using multi-class evidential maps in weights-of-evidence modelling.

Jan 1, 2001

By Jaroslaw W. Drelich

Despite the success of DLVO and extended-DLVO models that have been developed for homogeneous and smooth surfaces, a vast majority of practical surfaces encountered in mineral ore beneficiation are typically rough at various scales; they are also typically heterogeneous. The interactions of gas bubbles with particles having rough and heterogeneous surfaces are much more complex than the commonly used DLVO or extended-DLVO models predict. The effects of surface roughness on flotation and colloidal interactions have been reported many times in the past, although a clear understanding of their origins has been lacking. To explain differences in colloidal interactions for spherical hydrophobic particles, a theoretical analysis of the interaction potential was carried out for a model rough particle interacting with a bubble surface in an electrolyte solution in this study. The attractive hydrophobic interaction potential was added to repulsive retarded van der Waals and repulsive electrical double layer interaction potentials. The rough microscopic particles were modeled as spheres decorated with nano-sized asperities. Parameters that reflect common flotation separation systems were selected for testing this theoretical model and computation of the energy barrier applicable to particle – flat bubble surface interactions. It was found that hydrophobic asperities with the height of only several nanometers can reduce the repulsive interaction energy by an order of magnitude. Theoretical analysis also reveals that surface coverage of microscopic particles by nano-sized asperities is important as well. The findings of this research suggest that manipulating and engineering the particle surface topography could lead to better control over flotation separation.

Jan 1, 2016

By R. H. Coloquhoun

"INTRODUCTIONDome Mines Limited is located on 3,149 acres in Tisdale, Whitney and Shaw Townships in the City of Timmins in Northern Ontario. The mine and mill facilities are two miles from the town of South Porcupine, now part of greater Timmins.In April of 1909, J.S. Wilson of Massey, Ontario headed a party of prospectors into the Porcupine region. Disembarking from the Temiskaming and Northern Ontario Railway at mileage 222, they established an initial camp on the shore of Frederick House Lake. Following the lake ""break up"" they canoed to their destination, Porcupine Lake, and established a base camp on the west side of the lake by May 23, 1909. At a point approximately two miles from Porcupine Lake the moss on an outcrop was rolled back and gold was discovered.In the spring of 1911, the first mill structure was in the process of being built and consisted of 40 stamp mills, five S'x22' pebble mills and the ancillary equipment for a 300-400 T.P.O. operation. This structure was destroyed along with much of the Porcupine Camp by the famous Porcupine Fire of July 1911. By mid-1912, a steel ""fire proof"" structure was built and utilizing the salvaged mills from the fire, supplemented by the installation of three, 8'x30"" cylindro-conical Hardinge ball mills purchased third hand from Vipond Mines, processed 75,088 tons by year's end.The mill was again levelled by fire in October of 1929, this time caused by an overheated boiler stack. This 11 fire proof"" structure was immediately replaced by a wood structure and again the three Hardinge conical mills and the five 5'x22' pebble mills were restored and utilized. The new mill operated close to its daily capacity of 1500 tons during the last two months of 1930. During the rebuilding phase, the crushing plant was remodelled and a new crusher installed. These plants were protected from fire by a 60,000 gallon water tank and an automatic sprinkler system."

Jan 1, 1984

By D. A. MacFadyen, J. J. Brummer, C. C. Pegg

The early identification of a kimberlite dyke and the occurrence of pyrope garnet grains along a section of the Munro Esker north of Kirkland Lake encouraged the search for kimberlites. Subsequent exploration using data from aeromagnetic surveys completed for the Kirkland Lake Initiatives Program (KLIP) resulted in the discovery of five kimberlite diatremes in the area north of Kirkland Lake and another one to the south. These are only a portion of the cluster of pipes found so far that probably occur in the area. Recovery of the diamonds present in four of the pipes yielded 16 stones, the largest being 0.17 carats. Unfortunately evaluation of the pipes is a problem due to the cover of glacial drift, up to 92 m in thickness, which makes it difficult to obtain an adequate bulk sample. A study of their ages, mostly from drill hole samples, suggest that the kimberlite diatremes and other alkaline ultramafic rocks were emplaced along a northwesterly zone of rift structures. These alkaline ultramafic rocks cut across all earlier rock types and have ages ranging from 121 Ma to 173 Ma. The zone of deformation, along which these rocks occur, has been named the Lake Timiskaming Structural Zone (LTSZ), a modification of Lake Timiskaming Rift Valley (LTRV). Ultramafic intrusions which were emplaced along the LTSZ can be traced from the James Bay Lowlands in the northwest to past Belleville on the north shore of Lake Ontario in the southeast, a distance of about 1070 km. As the emplacement of these rock types become known more are certain to be found by drilling selected aeromagnetic anomalies. The project has demonstrated that aeromagnetic surveys can be used successfully to identify covered kimberlite targets.

Jan 1, 1992

By D. J. Parker, G. B. Tupper, I. Govender

Positron-Emission-Particle-Tracking (PEPT) has enabled the non-invasive observation of charge and slurry transport in model mills under operational conditions. We use high quality PEPT data to infer that the charge motion can be effectively described by a non-Newtonian granular fluid. An improved theory for slurry transport, including inertial effects, is presented.

Jan 1, 2012

Abstract: ?The paper will review the perspective of Scotia Capital on financing mines, mining projects and mining companies in today's world of major increases in commodity prices, increases in capital and operating costs, shifts in foreign exchange rates, and increasing scrutiny of mining's social license ?Focus on debt financing alternatives Key Assumptions: ?Assume financing a mining asset (i.e. not an exploration play) ?Exploration is generally financed with equity ?private placements or public offerings on an idea

May 1, 2006

By Yan Jie

The oxygen-enriched bottom-blowing continuous converting process for copper matte was recently developed by the China-ENFI Engineering Corporation. The first commercial plant based on this technology was successfully commissioned at the Yuguang smelter in China in March 2014. The present paper describes this new continuous converting process and compares technical characteristics with other continuous converting processes including: Kennecott-Outokumpu flash converting, the Mitsubishi Process, the Noranda Converter and TSL continuous converting. The bottom-blowing oxygenated continuous converter with competitive capex and opex costs is seen as an attractive alternative to the Peirce-Smith converter.

Jan 1, 2014

By R. Butar-Butar, J. Mosher, G. Banini, J. Hollow, A. Villanueva

The effect of High Pressure Grinding Rolls (HPGR), as a preceding stage to a conventional ball mill circuit at PT Freeport Indonesia’s C1/C2 concentrators, has been studied in terms of downstream grinding efficiency and circuit performance. When milling the product from the HPGR, mill capacity increased by 21% for the same product grind size, when compared to processing similar ore from a conventional crushing circuit. This achievement is a result of several reasons, among them: reduction in feed size (F80), fines generation beyond the proportional reduction in F80, reduction in ore hardness induced by HPGR comminution mechanism, optimization of the recycle system of the HPGR and ball string optimization in the ball mill circuit given the new feed to the mill.

Jan 1, 2012

By Robert J. McCarthy

Many technologies have been adopted over the last half century for the haulage of material from open pit mining operations. Some of the technologies utilized include rail, off-highway trucks, conveyors, and slurry pipelines - each having its unique application and benefits. Over time, truck haulage has become the primary means of surface mine material movement, though recently it has been plagued by problems of tire shortages, high diesel fuel costs, labour shortages, and carbon emissions. This paper focuses on In-Pit Crushing and Conveying (IPCC) as a competitor to truck haulage which has the potential to solve many of these problems. An overview of the available technology is presented along with measures required to overcome perceptional if not physical barriers to implementing this technology in modern open pit mines.

May 1, 2011

By Rainer Süss

An investigation was carried out by Mintek to investigate the influence of a range of alloying additions (vanadium, cobalt, zirconium, antimony and germanium) on the formability and hardenability of alloys with gold content >90 wt%. This paper reports on the hardening mechanisms that can be utilised to increase the hardness of gold (>90 wt% Au) by conventional alloying, as well as the hardening effect obtained by alloying with specific elements. Preparation methods for the alloys are described, which include the steps of melting, annealing, quenching, cold working and age hardening. Focus is given specifically on alloys that were developed at Mintek with a gold content >90 wt%, which are not only harder, but exhibit good resistance to tarnishing and corrosion.

Oct 1, 2003