Search Documents

By Seongki Lee

The purpose of this paper is to propose the real-time facility management system framework based on Building Information Model (BIM) and Web of Things. Latest IT such as BIM is rapidly spreading to architecture, civil engineering, engineering and maintenance with the aim of simplifying complex system in buildings and facilities, minimizing operation cost, providing high value services and advancing facility management. In particular, BIM-based management framework design to assist the development of sensor information operation system, which adds convenience to facility maintenance and management, has emerged as a key issue. To this end, this paper proposed conceptual framework for data warehouse, web service and interface that make up real-time facility management system. The paper also produced conceptual methodology on CoRE-based web service platform, mobile device, BIM and WSN mapping.

Aug 1, 2013

By Tom Shumka

INTRODUCTION ?This bull gear inspection technique was developed to provide more accurate data and faster inspection times than current techniques used today. ?Eddy Current Array (ECA) is a non-destructive testing technique that provides the ability to electronically drive multiple eddy current coils, which are placed side by side in the same probe assembly. Each individual eddy current coil in the probe produces a signal relative to the phase and amplitude of the structure below it. ?This data is referenced to an encoded position and time and represented graphically as a C-scan image. Most conventional eddy current flaw detection techniques can be reproduced with ECA inspections; however, the remarkable advantages of ECA technology allow improved inspection capabilities and significant time-savings.

Oct 1, 2010

By Xian Jian Guo, Lei Li, Hua Wang

The distribution and behavior of As, Pb and Zn elements in the copper smelting process were investigated using thermodynamics. The differences between thermodynamics evaluation and practical smelting processes were analyzed. The main factors affecting the distribution of the elements are oxygen enrichment in blowing, copper matte grade and smelting temperature. In general, the distribution ratio of As, Pb and Zn to off gas increases with the smelting temperature and decreases with oxygen enrichment in blowing. Meanwhile, their distributions in matte decreases and that in slag increases with the increase of copper matte grade. There is some gap in distributions between thermodynamics evaluation and practical smelting processes. INTRODUCTION The copper concentrates usually contain a number of minor elements, the control of which in copper smelting processes is often a key to the quality of the anode copper produced and may also have a bearing on the overall economics of the process (Yang et al., 2017). Knowledge of the thermodynamic properties of the minor elements in slag is very important in the control of the slagging reactions (Takeda Y, Ishiwata & Yazawa, 2007). In addition, the environmental contamination caused by the minor elements associated with copper-bearing ores, such as As, Pb and Zn, has become more and more important (Wang, 2004). Arsenic, lead and antimony, which are all carcinogenic metalloid elements, are usually contained in iron-rich wastes, and theirs emissions are considered to be one of the foremost environmental concerns (Wang, 2004). It is important to elucidate the elements distribution of them in the reducing-matte smelting process. The distributions of As, Pb and Zn elements in the copper smelting process are dependent on many factors, including the temperature, raw material composition, reduction atmosphere, concentration level, and slag chemistry etc. (Chen L Z, Xu X, 2016). Generally, these minor elements mainly distribute in phases of gas, copper matte and slag in the smelting process (Shu, Wang, & Qu, 2016). The arsenic exists mainly in the form of sulfo-arsenides in the copper concentrate, and it will decompose and be oxidized in the smelting process (Chen & Lu, 2016). Part of the products, including AsS, AsO, As2 and As2O3, evaporates into the gaseous state, and some other part enters into slag phase in the form of As2O3 and As2O5 (Wang, Guo, & Tian, 2017). Meanwhile, the As2O3 in the slag phase can also be reduced to metallic As and combine with Cu, S, Fe forming Cu3As2, As2S3 and Fe3As2, and then enter into copper matte. During the copper smelting process, about 50% of zinc enters into slag phase in the form of ZnO and 45% exists in the copper matte in the form of ZnS. Little volatizes into the gas phase. Most lead exists in forms of PbS and PbO in the copper concentrate, and it is mainly distributed in copper matte in the smelting process (Zheng & Lin, 2015).

Jan 1, 2019

By Chris McBean

Due diligence mistakes ? lost opportunity ? High profile write-downs and cost overruns ? Result ? tight market for financing ? Implications for due diligence ? need to get it right ? maybe only one chance ? Where should focus be?

May 1, 2013

By Michel Dagbert, Mohammed Harfi

"Abstract - The Draa Sfar polymetallic deposit, at about 16 km NW of Marrakech in Morocco, is a massive sulfide zone at the contact between an underlying volcanic and an overlying clastics sequence. The mineralized body is a flat lens with schistosity and "boudinage," tilted to the west and with a strong dip to the east. The lens extends over a strike length of about 2 km and from surface to a depth of about 1 km, with thickness varying from 1 m to almost 30 m. It has been intersected by about one hundred surface drill holes and, in its south part, by about thirty underground fan holes from two exploration levels at depths of 300 m and 400 m. On these two levels, the massive sulfide zone has been channel sampled over a cumulative length of about 0.7 km. Results from drill and channel samples are used to estimate the resources of the orebody according to several methods: sections, polygons around intercepts on a longitudinal plan, grids on the same longitudinal plan with various distance weighting methods including kriging and, finally, a 3D grid with the same range of interpolators. A comparison of the various estimates delineates the important factors in deriving resources for this type of deposit. Those factors are mostly geological and related to the interpretation of the geometry of the two limiting surfaces of the zone. For the 3D gridding, the authors have devised a new and original method that constrains the interpolation of blocks from samples to a geometry of limiting surfaces. The resulting model shows internal grade variations that parallel fluctuations of zone thickness and orientation without having to re-orientate the search window in each block. Résumé - Le gisement polymétallique de Draa Sfar, situé à environ 16 km au NW de Marrakech est un horizon de sulfure massif au contact d’une formation volcano-sédimentaire de base et d’une formation détritique sur-jacente. Le corps minéralisé se présente sous forme d’une méga-lentille aplatie, schistosée, boudinée et déversée vers l’ouest avec un fort pendage vers l’est s’étendant sur une longueur de 2 km et une profondeur de près de 1 km avec une épaisseur variant de moins d’un mètre à près de 30 m. Il a été reconnu par plus d’une centaine de sondages de surface et, dans sa partie sud, par une trentaine de trous souterrains en éventail à partir de deux niveaux à des profondeurs respectives de 300 m et 400 m. Sur ces mêmes niveaux, des traçages ont permis de rainurer le minerai sur une longueur cumulée de 0.7 km. Les données de sondage et de rainurage ont servi à estimer les ressources du gisement selon plusieurs méthodes : sections, polygones sur longitudinale, grille sur longitudinale avec différentes pondérations en fonction des distances incluant le krigeage et enfin grille tridimensionnelle avec le même éventail de pondérateurs. La comparaison des estimés obtenus permet de mettre en évidence les facteurs importants dans l’estimation des ressources de ce type de gisement. Ces facteurs sont essentiellement géologiques et relatifs à l’interprétation de la géométrie des limites des corps minéralisés. Pour l’estimation sur grille tridimensionnelle, on a mis au point une technique originale qui calque l’interpolation des blocs à partir des échantillons sur cette géométrie des surfaces de contact. Le modèle résultant montre des variations internes de teneurs qui épousent les fluctuations d’épaisseur et d’orientation de la zone sans qu’il soit nécessaire de ré-orienter les fenêtres de recherche dans chaque bloc."

Jan 1, 2002

By M. Lahtinen, H. Takala, B. Saxén

Oxidic zinc fume dusts are formed in electric arc furnace (EAF), Waelz furnace operations, and also in the Top Submerged Lance (TSL) furnace of Outotec Ausmelt. These dusts are normally considered as secondary raw materials for zinc metal production, as they are mainly originated from steel scrap recycling or zinc plant residue processing. The latest development in zinc fuming is direct smelting of zinc concentrates in the Ausmelt TSL furnace and hydrometallurgical treatment of produced fume dust. This technology is for primary zinc production like roasting and concentrate direct leaching, as concentrates are directly treated. The various oxidic zinc raw materials differ in composition and content of impurities. Thus, they require different hydrometallurgical processes to produce pure zinc metal. In addition to zinc these dusts typically contain also lead, silver and indium, which can be recovered and can increase recovered metal value significantly. From the impurity point of view the most relevant elements in the fume dusts are iron, arsenic, fluoride, chloride and cadmium. This paper describes hydrometallurgical processes to treat Ausmelt TSL fume dusts to extract valuable metals at high recovery and also to control and separate various impurities efficiently.

Jan 1, 2014

?Introduction to the Delphi Group ?Why is carbon important to your organization ?Key elements of a carbon management strategy ?Inventory ?Risk & opportunity scan ?Mitigation options and financial mechanisms ?Identify targets and develop policy ?Communication and improvement ?Manage for success

May 1, 2009

By W. Yang, R. Rajasingam, B. Tadesse, K. Mohanarangam

Copper electrowinning is a complex electrochemical process that involves the production of LME grade copper from copper rich electrolyte. The process involves the deposition of the copper ions onto the cathode from copper rich electrolyte with the production of oxygen bubbles at the anode. Acid mist is produced by these oxygen bubbles bursting at the electrolyte free surface. It is an undesired by-product of the Electrowinning process which unchecked could result in mist generation higher than the recommended time-weight-average exposure limit. Various approaches to alleviate the problem have been adopted by companies, all with varying degrees of success. All of these have been attempts to treat the symptom acid mist rather than the inherent problem, often proving expensive and, in some cases, ineffectual. In this paper, a new method was developed for acid mist quantification based on ‘total acid mist’ capture above the EW cell under well controlled conditions. With the use of sophisticated diagnostic analytical tools and measurement techniques it was possible to study all the operating variables including current density, flow rate, temperature, etc. independently and their effect on bubble size, bubble velocity, gas hold-up as well as acid mist generation and its droplet size. Results show that total acid mist capture increases with an increase in current density but remains more or less constant between 300–500 A m-2. Total acid mist also shows an increase with increasing electrolyte temperature. These findings are substantiated with the aid of bubble size and gas hold-up measurements with the transparent EW cell.

Jan 1, 2019

By T. McCallum, B. Wellbrook, T. Ratnaweera

Leaching of copper (Cu) concentrates produces elevated concentrations of Cu and acid, which makes solvent extraction (SX) processing more challenging. Maintaining extraction targets can be more difficult with higher pregnant leach solution (PLS) grades, and variability of PLS Cu and acid can lead to increased chemical iron transfer. Diluting concentrate leach feeds with an existing heap leach inventory makes SX processing easier. However, considerations about how much to dilute and where to distribute the flow into the SX configuration must be carefully evaluated, given their impact on metallurgical performance. In this paper, characteristics of a concentrate leach feed are discussed, along with considerations for processing by SX. Also reviewed are pilot plant results of concentrate leach distribution into SX and plans for commercial testing. INTRODUCTION Hydrometallurgical processing of copper concentrates continues to gain interest from the industry. Treatment by smelting and electrorefining continues to dominate, accounting for ~80% of global copper production, but is faced with its own challenges (Li et al, 2017). The case for increased hydrometallurgical processing has been discussed as high grade ore deposits are diminishing, capital costs for smelting are high, and the environmental aspects present challenges for sustainable practice. The hydromet copper industry is also turning a corner as easily leachable copper oxide deposits are depleting, and excess SX-EW capacity exists in certain regions. The transition to hydrometallurgical processing of copper concentrates will take a bit of effort as leaching of copper sulfides is difficult and byproduct credits must be considered. Various POX leaching processes have been studied and proposed to the industry as viable practices. Of the many processes, commercial use has been practiced with the Mount Gordon Copper Process, total and partial pressure oxidation by Freeport-McMoRan at their Bagdad and Morenci, Arizona complexes, the Sepon Copper Process in Laos, and the bioleach BIOCOP™ process in Chile (Dreisinger, 2016).

Jan 1, 2019

By M. Labrie, H. L. Gibson, G. Doiron, J. J. Watkins, D. H. Watkinson

The Corbet deposit is one of 17 proximal Cu-Zn massive sulfide deposits located. within the Noranda Cauldron which occurs within the core of the Noranda Volcanic Complex. The deposit is located at the top of the Havrian Formation, the lowermost formation of the 3000 m thick Mine Sequence; the deposit has Yielded 2.75 M tonnes of ore grading 3% Cu, 0.96% Zn, 2.06 g/t Ag and 1.0 g/t Au. The multi-lens Corbet deposit formed within a 250 m wide crater that occurs within a localized breccia pile. The Corbet breccia pile was constructed by explosive magmatic and hydrovolcanic eruptions localized along the south flank of a larger andesitic shield volcano that formed during the waning stages of Havrian volcanism. The breccia footwall of the deposit allowed unfocused and widespread hydrothermal discharge that resulted in the development of a large area of chlorite and fringing sericite alteration that exceeds, by six times, the size of the sulfide lenses and represents a significant exploration target.

Jan 1, 1993

By B. Vorobyov

A Canadian company, Sight Power Inc., has developed a revolutionary, fully automated shaft monitoring and inspection system for deep-level mining based on a 3D mobile laser scanning technology. It consists of a special hardware unit and proprietary software with Artificial Intelligence elements for object recognition, features identification and change detection. The main purpose of this system is to significantly improve the safety of underground mining as well as to increase the available hoisting time thus generating substantial additional revenue for the mine.

Aug 1, 2013

Flotation of a mineral bearing particle is the result of successful completion of a chain of events, such as, producing particles with sufficient exposure of the valuable mineral on the surface, reagent adsorption, suspension of the particle in the pulp, collision of particle with air bubbles and subsequent attachment, ascending to the froth column and transport to the concentrate stream, among others. These sub-processes in turn are affected by the feed properties such as size and density, and process variables such as size of air bubbles, degree of turbulence in the cell, particle/particle interactions etc.. Thus, inefficiencies occurring in any one or more of the above processes will result in inefficient flotation performance. In spite of its dependency on a wide variety of sub-processes, flotation performance is commonly modelled based on first order kinetics using two or three parameter models. As the model parameters may be affected by several of the sub-processes mentioned above, interpretation of their variations and identifying the specific causes is extremely difficult. Of the many factors that influence the flotation performance, liberation information of the particles such as the grade distribution and surface exposure are considered vitally important. In this paper, it has been demonstrated a) how a predictive liberation model may be derived and used in quantifying the liberation information of the particles produced at various grind sizes and b) how the flotation process may be modelled by explicitly incorporating the liberation information, thereby improving the accuracy of the model. Comparisons of the observed data with the proposed model and those of published liberation/flotation models have also been made.

Jan 1, 2016

By Hammenm R., J. Hammen, C. Hammen

"The production of salable Rare Earth Element (REE) products necessitates a sequence of chemical separation steps between the mine and market commodities. The effectiveness of the chemical separations that purify REE salts is critical to the success of the producer, as the purity of REE salt products affects their market price. This is due to the fact that impurities in REE salts, even at low levels, can be deleterious to the function and usability of the end product. The purification of REE by removal of low levels of contaminant has been referred to as "product polishing". The technologies commonly in use for product polishing, solvent extraction (SX) and ion exchange (IEX) are challenged by the availability of separation chemistries to separate the contaminant from the desired REE salt. In simple terms, if a product specification is 99.9% purity, the SX or IEX separation reagents need to have at least a 999:1 selectivity ratio. Significant testing has been carried out on the use of solid phase extraction (SPE) columns to extract low-level impurities such as aluminum or zinc from REE product streams. The SPE columns are nano-composite materials that have rapid equilibration kinetics with the solutes being processed by the columns. The SPE matrices have been modified with chelating ion exchange ligands that bind the contaminating ion with great selectivity in residence times of a few seconds. Thus, REE streams with 1 to 2% of contaminating aluminum ions, have been polished to >99.99% purity. In this paper, results are presented on the removal of aluminum impurity from a didymium (neodymium+praseodymium) product stream using SPE technology. The selection of the SPE medium and the process steps to treat the feed solution for aluminum removal and ultimate stripping and recycle of the solid phase extractant are discussed."

Jan 1, 2014

By N. Haghdadi, D. M. Maijer, A. B. Phillion

B206 is a recently-developed high-strength Al-Cu casting alloy with reduced Ti and Fe, as compared to the well-known AA 206 alloy, for improved hot tearing resistance. In the current study, the solidification kinetics of this alloy as a function of cooling rate from 1 to 15 K/min were studied using differential scanning calorimetry (DSC) and microscopy. Specifically, the evolution in fraction solid, grain size, and secondary dendrite arm spacing have been characterized. The DSC results show the occurrence of three peaks during cooling from the liquid state, which are related to the formation of primary aluminum, a pre-eutectic intermetallic, and the eutectic phases. Thermal analysis also indicates that while the liquidus temperature is not sensitive to the cooling rate, the temperatures at which the pre-eutectic and eutectic phases form are strongly coupled to the rate of heat extraction. A decrease in the latter temperatures was observed when the rate of solidification was increased, leading to a lengthening of the freezing range of the primary phase. The results will be useful for improving B206 casting processes, specifically through modification of mould cooling conditions.

Jan 1, 2014

By J. H. Rickard, D. H. Watkinson

"Abstract - Detailed petrographic and quantitative (electron microprobe, SEM-EDS) mineralchemical analyses of sulfide ore from the 100 orebody at the Copper Cliff North mine, Copper Cliff, Ontario, reveal numerous stages of ore development. Sharp contacts between weakly mineralized quartz diorite and blebby to massive sulfides indicate multiple intrusive events within the Copper Cliff offset dike. A spatial association of sulfides and hydrous minerals, such as amphibole, biotite, chlorite and epidote, suggests that most primary ore has been affected by later hydrothermal fluids. Sulfides are often enclosed or bordered by these secondary silicate phases. The ore consists primarily of pyrrhotite, pentlandite, chalcopyrite, with trace michenerite, cobaltite/gersdorffite, irarsite, hessite, tsumoite, and bismuth tellurides.Geological and petrological comparison of the 100 orebody and the adjacent 900 and 890 orebodies has revealed distinct similarities in ore distribution. Data show that the 100 orebody is depleted in platinum-group elements (PGE) relative to the 900 orebody. Platinum-group elements from the 100 orebody may have been hydrothermally remobilized and partly emplaced in the 900 orebody, in adjacent veins, or in magmatic breccia. Analysis of Cu, Ni, and PGE assay data of ore samples has characterized their distribution among the eight different ore textures in the orebody. There is a strong association between Pt and interstitial sulfide, and to a lesser extent massive sulfide, but little correlation between chalcopyrite-rich ore and PGE in the 100 orebody, unlike many other deposits in the Sudbury region."

Jan 1, 2001

By Laxman M. Amaratunga

"The fine fraction of tailings is usually excluded from the backfill process and generally disposed on the surface in tailings ponds. Because of the ever increasing demand for fine grinding in the extraction process for improved liberation of valuables in the ore, increased production of fines in the tailings has resulted. The negative impact of surface impoundment of tailings on the environment is well known. Amaratunga and Annor (1989) first presented a concept of fine tailings agglomeration for backfill.This paper presents the development of the novel cold-bond tailings agglomeration (CBTA) technology for non-reactive fine gold mill tailings. For cold-bond agglomeration regular portland cement was used as a binder. In order to cut costs, alternate binders such as lime, and blast furnace slag cement were examined. The effects of binder dosage, curing time, and agglomerate size on the fracture load strength of the agglomerate were studied.Fine tailings agglomerates are mixed with coarse tailings or non-agglomerated fine tailings to make high density fill compositions to be used as underground backfill. Alternatively, the agglomerates can be used as aggregates for surface applications. The paper discusses the environmental and operational benefits of this total tailings utilization and disposal technology.IntroductionIn Canadian mines, mill tailings are probably the most commonly used material for backfill. However, only the coarse fraction of tailings is desirable for use as hydraulic fill or high density fills. The fines are disposed on the surface in tailings ponds since they are unsuitable for underground backfilling owing to the following factors:i) slow settling ratesii) longer percolation timeiii) excessive consumption of binder due to drainageiv) poor compactionFor improved value liberation more milling operations have resolved to fine grinding in their comminution circuits. Gold milling operations driven by down stream leaching processes grind their ores excessively fine. In general, gold mines use hardly any tailings for backfilling. This can result in periodic short falls and the need to search for alternate backfill material from other sources. Apparently, the gold producers are the most identifiable sector which suffer from a shortage of backfill materials ( Amaratunga and Annor, 1989)."

Jan 1, 1994

"The Society for Mining, Metallurgy, and Exploration (SME) Inc. developed a guide of minimum standards for reporting exploration results, mineral resources, and mineral reserves for the purpose of informing the general public. The SME Guide has been adopted by the Society.History1. In 1988, at the request of members of the Society for Mining, Metallurgy, and Exploration (SME), Inc., the President of SME formed Working Party #79, Ore Reserve Definition, with the mission to develop guidelines for the public reporting of exploration results, resources, and reserves. A Subcommittee was appointed by the Working Party to draft these guidelines and submit recommendations to SME. The Subcommittee's recommendations were published by SME in the April 1991 issue of ""Mining Engineering"", and as a document entitled ""A Guide for Reporting Exploration Information, Resources, and Reserves"" (the SME Guide) in January 1992. Work continued on an ad-hoc basis until 1996, when Working Party #79 was renamed the SME Resources and Reserves Committee and became a standing committee.In 1994, the Council of Mining and Metallurgical Institutions (CMMI) started a concerted international effort to create a set of international definitions for reporting mineral resources and mineral reserves. An ad-hoc International Definitions Group was formed, with representatives from mining and metallurgical institutions from the United States (SME), Australia (AusIMM), Canada (CIM), the United Kingdom (IMM) and South Africa (SAIMM). A major breakthrough came on October 18, 1997 when the CMMI International Definitions Group met in Denver, Colorado and reached a provisional agreement (the Denver Accord) on definitions of mineral resources and mineral reserves. Concurrently, and since 1992, the United Nations Economic Commission for Europe (UN-ECE) was developing an international framework classification for mineral resources and mineral reserves. Starting in October 1998, joint meetings were held in Geneva between the CMMI International Definitions Group and the UN-ECE Task Force, resulting in agreement to incorporate the CMMI definitions into the UN framework classification."

Jan 1, 2003

By J. H. Reiss, D. F. Bruhn, Idaho National Laboratory, Y. Jiao, D. W. Reed, Y. Fujita, D. L. Daubaras

"Bioleaching offers a potential approach for recovery of rare earth elements (REE) from recyclable materials, such as fluorescent lamp phosphors or degraded industrial catalysts. Microorganisms were enriched from REE-containing ores and recyclable materials with the goal of identifying strains capable of extracting REE from solid materials. Over 100 heterotrophic microorganisms were isolated and screened for their ability to produce organic acids capable of leaching REE. The ten most promising isolates were most closely related to Pseudomonas, Acinetobacter and Talaromyces. Of the acids produced, gluconic acid appeared to be the most effective at leaching REE (yttrium, lanthanum, cerium, europium, and terbium) from retorted phosphor powders (RPP), fluidized cracking catalyst (FCC), and europium-doped yttrium oxide (YOEu). The Acinetobacter isolate, BH1, was the most capable strain and able to leach 33% of the total REE content from the FCC material. These results support the continuing evaluation of gluconic acid-producing microbes for large-scale REE recovery from recyclable materials.INTRODUCTIONAn enhanced recovery, substitute, reuse or recycle paradigm is important for balancing the supply and demand of critical materials (DOE, 2011). The recovery of rare earth elements (REE) from recyclable materials is an important component in this model. REE are used in a variety of modern products. For example, neodymium, europium, terbium, dysprosium, and yttrium are important for applications such as permanent magnets, lamp phosphors, rechargeable batteries, etc. (Binnemans, Jones, Blanpain, Van Gerven, Yang, Walton, & Buchert, 2013; DOE, 2011; Graedel, Harper, Nassar, & Reck, 2013). Cerium and lanthanum are used in glass polishers and additives in fluidized cracking catalysts (FCC)."

Jan 1, 2016

By S. M. Bulatovic, D. M. Wyslouzil, K. R. Rawlings

"The suitability of a new organic reagent DS20 as a depressant for oxidized and carbonaceous pyritic lead-zinc ore from Nanisivik Mines Ltd. has been evaluated in the laboratory and in the plant.The depressant DS20 is a mixture of Lignosulphonate-Dextrin-Quebracho and was developed specifically for depression of highly oxidized and carbonaceous pyrite.The laboratory test work indicated that the poor metallurgy resulting from the oxidized ore could be improved to normal plant performance by the addition of the DS20 depressant with the existing plant reagents. The laboratory data suggested that lime consumption could be reduced when using DS20.In this paper, the development work and the plant trials with DS20 are described.INTRODUCTIONNanisivik Mines Ltd. treats approximately 2000 tonnes per day of lead-zinc massive sulphide ore, containing currently 1% Pb and 9% Zn. The concentrator operations have been described previously (1,2) and typical metallurgical performance is detailed in Table I.The concentrator flowsheet (Figure No. 1) and the standard reagent scheme (Table No. 2) demonstrate the relative simplicity of treatment of this coarse grained ore.A recently discovered satellite orebody - Area 14 - containing 2% Pb and 12% Zn was brought into production in October 1983. This ore had been oxidized to varying degrees by ground water; the pyrite mineralization was found to be very fast floating and a carbonaceous constituent present in higher than normal proportion also affected flotation. The simple high lime addition could not control the pyrite, and very low grade lead concentrates resulted; zinc metallurgy was also affected by this oxidized condition (Table 3)."

Jan 1, 1986

By Cy Jordan, Ben Burdett, Adrian Dance, Jack Rainey

"In 1997, EIMCO Minerals installed a knowledge-based control system on one of the five primary grinding lines at Highland Valley Copper. The objective of the system is to maximise throughput without affecting circuit product size or flotation recovery. The system was commissioned in October 1997 on a SAG mill/ball mill circuit following a plant audit and upgrade of the control instrumentation.The system monitors and controls the SAG mill power, bearing pressure and recycle load by manipulating the solids feedrate, water addition and mill speed. The two ball mill and cyclone circuits are controlled through water addition at various points in the circuit as well as the number of operating cyclones.An on-line particle size analyser is used to measure the cyclone overflow quality. Models of the SAG mill charge level and overflow product size are also incorporated. A method of predicting the SAG mill power response to feedrate changes is used to lessen the effect of dead time for improved mill power control. In the future, inferred measurements of SAG feed particle size and hardness will allow changes in ore behaviour to be predicted and compensated for by the system.This paper describes the development of the project -from installation and commissioning to modifications and refinement -along with prospects for the future.BackgroundIn early 1997, EIMCO Minerals was contracted by Highland Valley Copper to install a knowledge-based or expert system control strategy on one of the five grinding lines in the mill. This was to become the start of the Advanced Control Project at Highland Valley Copper (HVC). This paper will review the progress of the Project as well as discuss the prospects for the future.Following a preliminary engineering study (or plant audit) by EIMCO in 1996, it was decided to implement an advanced control system in order to improve plant operations and increase productivity. The study suggested that such a system had a pay-back period of a few months through increased throughput without loss in flotation recovery. Highland Valley already had successfully applied higher level control through their Elsag Bailey distributed control system (DCS) and this was the next stage in process optimisation."

Jan 1, 1998