Search Documents

By M. Fairman

The effect of welding speed on the microstructure of friction stir processed (FSPed) AZ31B-H24 magnesium alloy was studied using light microscopy, image analysis, and microhardness tests. The grain size of the magnesium alloy was observed to increase after FSP from about 3.5 µm in the base alloy to about 8 µm in the stir zone. The aspect ratio decreased from 1.60 to 1.55 towards the center of the stir zone. The changes in the grain size and shape caused the microhardness of the samples to drop significantly across the FSPed region from 75 HV in the base alloy to below 55 HV in the stir zone. Decreasing the welding speed increased the grain size due to a greater input of heat energy. The faster heating rate due to the lower welding speed caused a deeper penetration of the annealing effects of FSP. It was also observed that the annealing effects caused by FSP were less pronounced with increasing distance from the interface between the sample and pin tool shoulder. The Hall-Petch type relationship of the micro-indentation hardness as a function of the grain size was observed to hold true after FSP.

Jan 1, 2007

By G. R. Davidge

"Falconbridge Mine has a history of significant microseismic activity dating back to 1955. Since mid-1981, a microseismic monitoring system has been operating in the area around the No .9 Shaft hoist room located 25 m from the are zone at a depth of 1200m. Several mine wide faults dissect this area and have been shown to be microseismic-active due to mining. The microseismic monitor has been interfaced with a small dedicated personal computer and a communications device to perform routine data evaluation and to produce graphical output. The programs are described and selected result s from the monitoring program are presented.IntroductionFalconbridge Mine is located on the southeast rim of the Sudbury Basin. The nickel-copper sulphide ore zone is essentially a tabular orebody striking approximately east-west and dipping at 80 degrees north near surface and rolling to 75 degrees to 80 degree s south by the 1000 level. (Mine level number s represent the approximate depth in feet below ground surface .) This dip is maintained down to the 6000 level. The north wall is comprised of jointed norite and a faulted contact up to 1 m thick exists between the ore zone and the norite. The south wall rock is a greenstone with highly siliceous lenses and often has a faulted contact with the ore zone. No less than five mine wide faults exist, as shown in Fig. I.Mining ha s been carried out from virtually the bedrock contact to depths of 1830 m although the majority of current activity is between 900 and 1500 m below surface. A winze provides access below the 4025 level and the cage hoist room is located on the 3850 level in the north wall 25 m from the contact. Because of concern for the stability of this hoist room, there has been no mining activity within 60 m of the hoist room and by 1980 this block of ore was one of the major blocks of high-grade ore remaining in the mine . Mining of this block was originally scheduled for very late in the decade.Prior to a six-month shutdown in 1982, this mine produced approximately 450,000 tonnes of ore annually, mainly by cut and- fill techniques. Following the shutdown, annual production has been reduced to approximately 200,000 tonnes and production is now mainly by undercut and fill techniques .Mining-induced seismicity has occurred at Falconbridge Mine since at least 1955 and reviews of the microseismic problems for the periods from 1965 - 1970 and from 1971 to 1979 were made by Singh (1971) and Vongpaisal et al. (1980), respectively. The need for instrumentation was addressed by these authors. Following several large events during the spring of 1980, a decision was made to investigate existing microseismic monitors and to apply micro seismic monitoring techniques in Falconbridge Mine. Application of microseismic monitoring to Falconbridge Mine was to concentrate on the No . 9 Shaft hoist room area of the mine, particularly around the 4025 level where a large mechanized cut-and- fill stope was approaching this level. By mid - 1981, the microseismic monitor was fully installed and with in a year , a short-period seismograph and a personal computer had been added to the system."

Jan 1, 1984

By S. Zador

"IntroductionIn the past decade, metallurgical and mining companies have shown an increased interest in the licensing of technology. When licensing technology, it is usually to the benefit of the parties, to have at least some of the technology to be licensed protected by a patent.This paper is intended to bridge the gap between the engineer in the field of mining, metallurgy and mineral processing who is interested in exploiting an invention commercially, and the patent agent or intellectual property lawyer whom he/she might retain to prepare a patent application and then prosecute the application to obtain a granted patent. It is also intended to encourage the inventor or a small business concern to consider the value of patents in the sale and licensing of technology. The lawyer may subsequently advise and assist the inventor in licensing his/her invention.A brief outline of some of the basic features of the patent system follows. The nature of the information, which the patent professional requires from the inventor to enable him/her to draft a patent application, will also be considered in general terms. Furthermore, various types of licenses which may be drawn up between a licensor of specific technical information and a licensee, will be listed and briefly discussed. No attempt, however, will be made to give a comprehensive and detailed account of the above aspects; the interested reader should consult legal publication and reference books, and patent professionals for further specific information.A granted patent is a document which describes an invention and how to practise it. The claims of the granted patent, figuratively speaking, fence off the intellectual property the inventor regards as his invention. The Commissioner of Patents, representing the Government, grants to the inventor or his assignee the exclusive right of making, constructing and using the invention, and selling it to others to be used, for a limited period of time, in exchange for disclosing the invention to the public. Thus, a patent prevents others from practising the claimed invention but it does not, necessarily, bestow the right to the patentee to practise his own invention. The term of a patent now in Canada and in most of the developed countries of the world, is 20 years from the date of filing the patent application. In the United States the patent term is still 17 years from the date of issuance of the patent. In Canada, the term was changed to 20 years in the new Canadian Patent Act which came into force on October 2, 1989. Any patent application filed prior to that date or granted before it, retains a 17 year life, commencing at the time of grant."

Jan 1, 1991

By A. Kraly, M. Complojer, P. Paschen, K. Gamweger, H. Antrekowitsch

Increasing quality of aluminium alloys and continuous optimization of the production process leads to an improvement of the gas purging systems. The application of porous plugs for the treatment of liquid aluminum is nowadays not widely used in the aluminium industry especially in Europe. The Department of Nonferrous Metallurgy and the Christian Doppler Laboratory of Secondary Metallurgy of Nonferrous Metals intensified the research and development of refining and alloying processes by gas treatment during the last years. CFD-modeling supports these experiments, which should lead to lower hydrogen content, lower suspended particles and a better distribution of alloying elements in the melt. Different parameters such as temperature, bubble size, gas amount and which kind of gas is used influence the quality of the products.

Jan 1, 2006

By A. Chaisantikulwat

Most solid-oxide fuel cell (SOFC) modeling emphasizes steady state cell operation. However, understanding the dynamic behavior is essential to predict the performance and limitations of SOFC power systems. In this work, we demonstrate a dynamic model of a SOFC, and we simulate a feedback control scheme that can maintain output voltage despite load changes. Dynamic response is determined as the solution of coupled partial differential equations derived from conservation laws for energy, mass and electric charge. From such a model, the step responses to system input variables can be determined. Low order dynamic models that are sufficient for feedback control design can be derived from the step responses. The development of the partial differential equation model is outlined, and the limitations of the control system are discussed.

Jan 1, 2005

By G. K. Herzog

THE problems relating to the construction and use o{ mining equipment are basically the same as those pertaining to equipment in other industries. It is true that much mining equipment is subjected to an unusually severe combination of shock, high stresses, abrasive wear, and corrosive ? conditions, but in other industries, also, equipment must operate under similar adverse conditions, so that their experiences may readily be applied to the problems of the mining industry. Steel and iron are for obvious reasons the most suitable materials for the construction of the greater part of the equipment used in the mining industry. For a large percentage of uses, the ordinary plain carbon-steels and ordinary or unalloyed cast-iron are, and probably will continue to be for a long rime, entirely satisfactory materials. There are, however, many. conditions which cannot be satisfactorily taken care of by these materials, and alloy steels and irons must be used where the greatest possible economy is desired. In general, alloy steels and irons are used where it is necessary or economically desirable to use materials possessing properties superior to plain carbon-steel or ordinary cast-irons, such as: (a) better strength (b) better wear resistance (c) better corrosion resistance (d) better resistance to high temperatures (e) better resistance to low temperatures or combinations of two or more of these advantages. There are also conditions where materials having other special properties are required, such as, for example, certain magnetic or electrical properties for electrical machinery; but in the great majority of cases, one or more of the five advantages listed are the most desired.

Jan 1, 1938

By D. M. Watson

Mineral discoveries and subsequent extraction have led to the establishment of many small communities, some major towns and a few cities . In Canada, such developments have essentially occurred without benefit of long-range regional or local planning. In the past, this was not a cause for concern. Now, however, rising expectations and reorientation of social values have placed increasing responsibility on government and industry to ensure the long-term viability of communities and regions. Such responsibility means large investments by government in infrastructure and by industry in extractive and processing plants. Uncertainty in the interpretation of ore reserve estimates becomes a critical factor. The traditional methods of reporting reserves - "proven", "probable" , "possible" - may be useful in individual mine production planning, but they are inadequate for planning industrial and public infrastructure, The need for a better information base is critical, with clear and precise definitions of what is being reported, but we are a long way from achieving it. The challenge is therefore to develop a closer professional relationship between government and industry and to tie mineral development to long-range regional strategies.

Jan 1, 1977

By S. S. Rahman, A. Gholami, M. A. Aghighi

"This paper provides a foundation for studying the growth of fractures in presence of other discontinuities and different anisotropies of low permeable hydrocarbon formations and helps to improve the design strategies for multistage fracturing.The multistage fracturing technology has recently been used to exploit low permeable hydrocarbon reservoirs. However, the mechanism of hydraulic fractures interaction and the impact of local heterogeneities on ultimate trajectory of the growing hydraulic fractures are not yet understood in depth. A fully coupled poroelastic Finite Element based model is developed to investigate the mixed mode propagation behaviour of growing hydraulic fractures. This model takes advantage of an explicit representation of the fracture which enables us to take the effects of rock and fluid related parameters into account. Moreover, impact of fracture geometry and leak-off phenomenon is investigated. The refined mesh around the crack provides the added advantage of more detailed stress distribution, pore pressure change and back stress in the vicinity of the fracture and in particular at the fracture tip. The potential deviation propensity of the fractures is evaluated based on the fundamental rule that fractures propagate perpendicular to the direction of the minimum horizontal stress.This study shows that pressurization of transverse hydraulic fractures results in the reorientation of local principal stresses, particularly in vicinity of fracture tips. Variation of flow patterns clearly influences the evolution of shear stress around the fracture tips which will potentially lead to mixed-mode I and II fracturing and consequently, fracture deviation. The presence of local heterogeneities such as preexisting fissures and/or fractures is a main source of such pore pressure induced stress redistribution and reorientation and potential deviation of hydraulic fractures.Most existing models ignore or simplify the effect of pore pressure/stress coupling as well as the fracture geometry and fluid flow within the fracture. Also, the fluid leak-off from the hydraulic fracture into the formation, which is a controlling factor in fracture growth, is often considered using analytical models. Taking advantage of a fully coupled porelastic model along with an explicitly discretized fracture, this study provides a more realistic insight into the complex fracture propagation processes of multistage fracturing operations particularly in presence of reservoir geo-mechanical complexities."

Jan 1, 2015

By Xue Yang

Even though many approaches have been proposed for automated fault detection and diagnosis of Heating Ventilation and Air Conditioning (HVAC) systems, and advanced maintenance programs, such as preventive and predictive maintenance have been applied for the systems, issuing work orders for corrective maintenance is still a reality. Currently corrective maintenance still accounts for more than 55% of all maintenance programs in average facilities in the US (DoE, 2010). Indoor air related problems are especially important among corrective maintenance work orders. This paper provides details of a case study conducted to capture the workflow that HVAC mechanics follow, their rationale in diagnosis process and the information they typically refer to while responding to indoor air related corrective maintenance work orders. The general workflow for HVAC mechanics to complete such types of work orders was summarized into 5 stages, and generic information requirements recorded from the case study were synthesized. Initial findings show two main challenges in the industry for HVAC mechanics to get access to required information, which highlights the need for a systematic approach that would enable identification of such information applicable to a given context under which a work order has been generated and provide values of required information for HVAC mechanics to do sound diagnosis through integrated data repositories.

Aug 1, 2013

By W. T. Thompson, S. Durham, K. M. Jaansalu

The role of platinum on the relative stability of gamma - gamma prime equilibrium is only qualitatively known, and may bear upon the stability of a superalloy under a protective coating. The binary phase diagrams Ni-Pt and Al-Pt, and the Ni-rich corner of the Ni-Al-Pt ternary, are reviewed and simple self-consistent thermodynamic models are derived. These thermodynamic models are incorporated into a database used to predict the gamma-gamma prime equilibrium for single crystal superalloys. In small concentrations, platinum is predicted to increase the temperature stability, but not the proportion, of the gamma prime phase over the gamma phase in third generation alloys such as CMSX-10. Another effect of platinum addition is to significantly lower the solidus temperature. These findings are compared to experimental data in the literature.

Jan 1, 2004

By J. W. Matousek

"Computer modeling of smelting processes requires internally consistent equations for calculating the compositions of mattes and slags. That is, the sum of the calculated assays must total 100%. One set of equations that satisfies this requirement for copper produced under oxidizing conditions (pSO2>one atmosphere pressure) is given by the following:%[Fe] = 62.0 – 0.775%[Cu]%[S] = 28.0 – 0.00125%[Cu]2%[O] = 10.0 – 0.225%[Cu] + 0.00125 %[Cu]2Mattes containing nickel in appreciable quantities do not have the defined “white metal” end point of approximately 80 percent copper and 20 percent sulphur that is found in the copper system during the converting process. The above equations, however, are readily extended to nickel and nickel/copper mattes for any desired end product composition."

Jan 1, 1996

By T. Moyo

Ammoniacal solutions are attractive and effective lixiviants for the dissolution of chalcopyrite, allowing for the formation of stable ammine complexes with copper while rejecting iron. Chalcopyrite dissolution in ammoniacal solutions is reviewed from literature, and results from a recently completed study evaluating it through electrochemical and controlled leach studies are discussed. Ammoniacal leaching of copper ores dates back to 1916 in the leaching of low grade copper ores in the Kennecott leaching plant and in the Calumet and Hecla mines, followed by the commercialisation of the Sherrit Gordon process for the ammoniacal leaching of sulphide copper ores in 1948. Since then ammoniacal leaching has received intermittent focus from researchers with the development of the Anaconda’s Arbiter process and the unsuccessful Escondida process. In these leaching processes, the formation of surface deposits has historically been reported to result in the passivation of the chalcopyrite surfaces, whereas oxygen mass transfer in solutions has been the focus of process design improvements. Results of studies on high grade chalcopyrite material is presented in this paper which show that although a surface deposit was formed, it did not result in the passivation of chalcopyrite in ammoniacal solutions, and that while oxygen transfer is critical, it is not the direct oxidant in the reaction. INTRODUCTION Ammonia and its salts have been used in the hydrometallurgical treatment of non-ferrous metals such as copper, cobalt and nickel from oxide ores. Its chemistry allows for the selective dissolution of desired metals, leaving behind gangue including iron. Chalcopyrite is a copper sulphide ore known to be very stable and hence recalcitrant to many hydrometallurgical processing methods. Thus, the dissolution of chalcopyrite continues to be an attractive area of research. The dissolution of chalcopyrite in ammoniacal solutions is possible due to the stabilisation of copper(I) and copper (II) ions by ammonia in alkaline media. Ammonia has become more attractive as a lixiviant during the present socio-economic climate due to its low toxicity, relatively low cost and ease of regeneration by evaporation (Meng & Han, 1996). Ammonia processes are ideal when the gangue minerals are acid consuming e.g. with calcareous or dolomitic gangue (Paynter, 1973).

Jan 1, 2019

By Man-Chao He

One of the critical problems involved in deep coalmines is unusual gas emissions. Many researchers agree that there is a relationship between coal gas emissions and geological features such as tectonics or geological disturbances, gas content, properties of the coal and rock and the mininginduced stress state in the coal seam and rock. Thus, the present paper intends to investigate complex mechanical phenomena during the process of gas emission in underground coal-mines. A program of laboratory testing was undertaken to study the effects of temperature and pressure on mechanisms of gas emission. It must be noted that this paper describes new techniques developed to simultaneously measure deformation and gas pressure, as well as flux during the test, taking the characteristics of gas transport into consideration under certain temperature and pressure conditions. The results indicate that under certain temperature and pressure conditions, gases adsorbed to coal start to desorb, and increase the pore pressure. High pressure gases entering coal fractures can generate high tensile stresses near the crack tips, leading to crack propagation and coalescence, which in turn can cause the specimen to dilate. From the experimental viewpoint, these test results may help us discern why mining seismic events can trigger gas emissions.

Aug 1, 2013

By A. A. Ruitenberg, G. Ruitenberg, J. Chandra

"The Caledonian Belt is mainly underlain by Late Precambrian and possibly Early Palaeozoic rocks, which are in part overlain by younger strata. Most of these rocks are weakly deformed, except for those in some linear . zones, which have been intensely deformed by cataclasis. Mineral deposits related to two distinct metallization episodes have been recognized. The earliest are zinccopper- lead sulphide deposits, which have been concentrated in the axial regions of late-stage cross-folds within the main cataclastic zone. The host rocks are andesitic and dacitic tuffs which show effects of intense talcose alteration, silicification and chloritization. Deposits related to the second episode are mainly composed of copper sulphides with locally abundant tennantite and tetrahedrite, which occur in brecciated and fractured carbonate-quartz veins. These veins postdate the late-stage cross-folds. VLF-EM and high-sensitivity magnetics proved to be very effective in delineating the geology of these deposits."

Jan 1, 1972

By Fadi Layyous Gedeon, David Hatton, Solomon Mogashoa, Tuhin Banerjee, Faisal Aljohani

The adoption of innovative technologies in mineral processing often raises concerns about complexity and integration. However, Woodgrove’s Direct Flotation Reactor (DFR) technology at Barrick’s Jabal Sayid copper concentrator provides a different perspective. This paper outlines the smooth integration of DFR technology from piloting to full-scale commissioning, showcasing how easily the cells were brought online. Installed in a cleaner scalper role, DFR cells at Jabal Sayid upgrade re-ground rougher concentrate to final concentrate in one stage. Despite processing challenging ore, the DFR cells delivered concentrate grades that consistently exceeded expectations. The commissioning process was straightforward with minimal hurdles, highlighting the technology's user-friendly nature. This paper advocates for a shift in perceptions about new technologies in mineral processing. The success of DFR technology at Jabal Sayid demonstrates that “different” doesn’t mean “difficult.” By focusing on ease of commissioning and operational integration, innovative solutions can enhance processes, improving efficiency and productivity in the mining industry.

May 4, 2025

By H. Perez, A. Lavoie, V. Prévost, P. Létourneau, P. Lind

The Home smelter is a custom copper smelter located in Rouyn-Noranda, Quebec. In 2005, the smelter produced 145,000 t of copper containing 807,000 oz of gold, 20,388,000 oz of silver in addition to 515,000 t of sulphuric acid. Recently, a flexible flow sheet has been developed incorporating the intermittent use of the Noranda Continuous Converter allowing for the increasing or decreasing of production based on market conditions, while attaining 90% or greater sulphur fixation regardless of operating mode. For 2006, the smelter is operating in full production mode and production is expected to be approximately 185,000 tm of copper. Mechanical modifications, process changes, metallurgical concepts, minor element treatments, and operational techniques that have allowed the smelter to develop this flexibility are presented. Current efforts to increase the productivity of the converter aisle and anode furnaces as well as improvements being made to address fugitive emissions are also discussed.

Jan 1, 2007

By M. W. Mikhail, R. J. Mikula

"Funding has been made available through the National Energy Program to build a mobile fine coal treatment plant. The plant is intended f or field application and also to upgrade the existing pilot plant facilities.Western Canadian coals with high proportions of fines (due 10 their friability) cause high losses of fine coal to the reject and in turn reduce the over-all recovery of saleable coal. Eastern Canadian coals with high amounts of sulphur of ten require crushing to fin e sizes to liberate pyrite and therefore need effective and efficient separation of these fine sulphur particles. The difficulties involved in solving these problems are two-fold. One is the reluctance to experiment in an operating wash plant and the other is that laboratory scale testing often cannot be extrapolated to the plant environment. The mobile fine cleaning plant with its ability to operate at existing coal preparation plants across Canada and with its flexibility in implementing flowsheet option s and close monitoring of fine coal circuit variables, is ideally suited to solve these fine coal cleaning problems. The mobile plant objectives are to design and optimize flowsheets, evaluate and improve fine cleaning circuit operations and 10 lest new process monitoring and control equipment.The schedule for construction and the required resources will be outlined along with flowsheet options and the general R&D philosophy of the mobile plant.IntroductionIn relation to coal preparation technology, Canadian coal s can be grouped as Eastern coal, Rocky Mountain metallurgical coal and Foothills high volatile bituminous coal. The eastern coals have high sulphur contents and in some cases require crushing or even grinding to liberate the fine pyrite . Rocky Mountain metallurgical coals often occur in highly sheared seams which have been subjected to rapid coalification. The high friability of these coals means that degradation during mining, handling and processing is extensive and results in large amounts of fine s ranging between 20 and 60% by mass of the wash plant feed. The widely varying geo logical structure and exposure to the elements results in partially oxidized coals which perform inconsistently in the traditional method of fine cleaning by flotation . Foothills high volatile bituminous coals for thermal use are frequently interbedded with soft shales and bentonitic clays. These clays disintegrate during washing and swell, producing large volumes of tailings. The presence of clays in plant circuits, particularly fine circuits, tends to increase the viscosity and may cause deterioration of the fines density separation and increase magnetite losses. In view of the fact that fine coal cleaning is the most difficult aspect of coal preparation , a research program is being established to study the factors involved and to offer some solutions.A recent performance evaluation of Canadian washeries showed that yield losses in the minus 2 mm coal circuits were approximately ten times those occurring in the coarse coal circuits(1). Because 2 mm x 0 coal represents 30 to 70 per cent of the raw coal, these losses can be considerable . The operating and capital costs of beneficiating minus 6 mm coal are about four to five times higher than for plus 6 mm coal. In the case o f minus 2 mm coal the costs are even higher. The economic importance of the fine coal cleaning cannot be over emphasized and as a result, the CANMET R&D program is geared for fine coal beneficiation."

Jan 1, 1984

By D. K. Sarkar, Jiawei Xiong

"Self-assembled monolayers (SAM) on the aluminum substrates are used as the adhesion promoter between two aluminum substrates when bonded with the adhesive in adhesive bonding technology. Traditional surface analysis tools are not capable of identifying the presence of SAM on a surface; therefore, EIS has been used to determine their presence on the aluminum substrates. In this study SAMs have been deposited on aluminum using the monomer of (3-Glycidyloxypropyl)trimethoxysilane (GPTS) organosilane. AA6061 aluminum alloys substrates were chemically cleaned with NaOH and HNO3 to remove the native oxides, followed by immersion in silane solutions. In a second method, SAMs were prepared by applying a spin coating of silane solution to the samples. The prepared SAM coated aluminum samples were analysed by EIS in the three electrode corrosion cell using a diluted alkaline solution. The impedance of the SAM coated aluminum is found be higher than the as-received aluminum. It has been also observed that the open circuit potential (OCP) of the SAM coated aluminum is higher than the as-received aluminum. Both elevated values of the impedance and OCP confirm the presence of SAM on aluminum.INTRODUCTIONSelf-assembly (Schreiber, 2000) is defined as the spontaneous formation of complex hierarchical structures from pre-designed building blocks, typically involving multiple energy scales and multiple degrees of freedom. Generally speaking, SAMs are created by the chemisorption of ""head groups"" onto a substrate from either the vapor or liquid phase followed by a slow organization of ""tail groups"" of a molecule. Typically, head groups are connected to a molecular chain in which the terminal end can be functionalized with groups such as –OH, –NH2, –COOH, or –SH to vary the wetting and interfacial properties (Chauhan et al., 2007; Ulman, 1996; Vashist, Lam, Hrapovic, Male, & Luong, 2014). Though there exist several methods to prepare SAM (Chauhan et al., 2007; Chen, Yang, & Zhang, 2014; Cho, Park, Jon, & Choi, 2007; Igor Luzinov, 2000; Reis, de Melo, & Costa, 2006; Song, Zhai, Wang, & Jiang, 2006; Sugimura, Hozumi, Kameyama, & Takai, 2002; Vashist et al., 2014), the two methods vapor phase (Song et al., 2006; Sugimura et al., 2002) and solution(Chen et al., 2014; Igor Luzinov, 2000) are commonly used. Recently, many articles have been published on the fabrication of superhydrophobic surfaces with SAM technology (Cho et al., 2007; Pan, Shen, Shang, & Xing, 2012; Siddaramanna, Saleema, & Sarkar, 2014; Song et al., 2006). Brassard, Sarkar, and Perron (2011) successfully obtained a superhydrophobic film by applying fluoroalkylsilane via self-assembly on monodispersive silica. SAMs are also reported as good candidates for anti-corrosion and adhesion promotion (Chen et al., 2014; Saleema, Sarkar, Paynter, Gallant, & Eskandarian, 2012). However, papers on the characterization of SAM properties are rarely seen. The most commonly used substrate for SAM is silicon and the method implemented is scanning probe microscopy (SPM) such as atomic force microscope (AFM) (Igor Luzinov, 2000; Moores, 2011; Zhang, 2003, 2005). Igor Luzinov (2000) analyzed the epoxysilane SAMs’ surface morphology and microstructure properties using scanning probe microscopy (SPM) and ellipsometry on single-crystal silicon wafers. SAMs have been used to improve the adhesion bonding of aluminum or plastics but no characteristic data have been presented yet (Saleema et al., 2012; Telegdi, 2007; Wang, Xu, Luo, Wang, & Wang, 2009). Recently, Reis et al.(Reis et al., 2006) have studied SAM of alkane diphosphonate (Gardobond X4661) on Al 5052 alloy samples by EIS in a naturally aerated sodium sulfate solution."

Jan 1, 2016

By E. R. Landry

This paper reviews the current state of electric furnace technology, with emphasis on some of the more recent developments. A large section of the paper is devoted to the use of increasingly high power inputs by arc furnace operators. Operating practices are then covered, including some of the newer techniques which have been tried.

Jan 1, 1967

By J. Baumbach, H. Bombach, M. Stelter

"Today technical electro-refining processes for copper exclusively use sulfuric acid, for silver refining nitric acid electrolytes are used. Sulfuric acid is characterized by very good chemical and electrochemical stability, good conductivity and low cost. The disadvantages of sulfuric acid are the precipitation of fine-grained cathodes with smooth surfaces only by using additives like glue, thiourea and chloride. In case of silver the electrolyte is electrochemical unstable and bears the risk of the formation of toxic NOx when pH is too low. A second disadvantage is the form of electrodeposition of silver as dendrites with their removal from the bottom of the Möbius cells.This paper reports the results concerning the application of an alternative electrolyte in copper and silver electro-refining. At first the electrolyte was characterized by the determination of current density potential curves. Electrolysis experiments were performed in laboratory scale using technical anodes for copper and synthetic anodes for silver. During the copper tests the solubility of contaminations from the anodes and the amount and chemical composition of the anode slimes were determined. Moreover the influence of current density, electrolyte temperature and the effect of several additives on the precipitation and chemical purity of the cathodes were investigated. In all experiments cell voltage as well as anodic and cathodic polarization was measured and current efficiency and specific energy consumption were calculated. A comparison with the results with those of tests using conventional sulfuric acid electrolyte shows the advantages and disadvantages of both systems, additionally the technical application chances and limitations for the new electrolyte. This electrolyte enables the precipitation of smooth copper cathodes with low silver and sulfur concentrations even at lower temperatures without any additive. For silver refining the electrodeposition of compact silver sheets is possible, that can be stripped comparable to those in copper electro-refining."

Jan 1, 2016