Search Documents

By E. C. Keeley

THE property of Buffalo Ankerite Gold Mines, Limited, is in Delora township, Porcupine area, Ontario. The southwestern part of the property is ground formerly owned by Marbuan Gold Mines, Limited, which was acquired by Buffalo Ankerite in January, 1936. Until 1938, the Ankerite (or North) mine and the Marbuan (or South) mine continued as separate operations, each developed through a surface shaft and winze to the 1050 level and each having its own mill. This meant high hoisting costs, which, in 1936 and 1937, amounted to 36 cents per ton. In 1938, the underground workings of the two mines were connected on the 1050 level, and ore from both mines was hoisted at the main, or No. 2, shaft of the North mine, location of which is shown in Figure l. This shaft was discontinued at a depth of 1150 feet because, owing to the soft nature of the talc (serpentine) rock in which it was sunk, it had to be concreted throughout, and also because of its great distance--1,100 feet and 1,400 feet, respectively-from the North and South orebodies.

Jan 1, 1945

By Mihaita Matei

An adaptive approach to control the deformation in tube hydroforming process is presented. This requires: the use of an existing non-linear FE software (ABAQUS) that incorporates a user material model (VUMAT), the development and implementation of an adaptive control strategy to coordinate the internal pressure and the axial load so as to prevent fracture and wrinkling failures (knowledge-base controller) and the application of the developed adaptive simulation approach for finding the optimal loading path required to hydroform a defect-free part with as uniform thickness distribution as possible (user's load subroutine (VDLOAD). In order to validate the approach, the case of conical hydroforming and the case of bending followed by hydroforming component is discussed.

Jan 1, 2011

By K. Nikkhah, N. Dhadli, G. Freeman

Ammoniacal pressure leaching operations have been in commercial use at the Fort Saskatchewan refinery of Sherritt International Corporation since 1954. Recent improvements have significantly increased the capacity of this circuit. The computer modeling of this process has proved to be a valuable tool in facilitating the evaluation of different operating scenarios in an effective manner. Reagent response in the ammonia leach of nickel and cobalt sulphides is examined using the dynamic process simulation capabilities of IDEAS(TM) software. The dynamic simulation enables accurate measurement of the sensitivity of the process to variables such as temperature, feed rate and ammonia concentration as well as compartmental analysis of metals concentration, pulp density, vent gas composition, and the formation of specific complexes. The complexity of the ammonia leach process makes it a logical choice for evaluation by computational analysis. The methodology for dynamic modeling of a pressure leach process is presented.

Jan 1, 2005

By J. J. McDougall

Until quite recently, the coal in the Cape Breton field was won from comparatively thick seams with light cover, and from submarine areas, and the system of mining naturally followed was pillar-and-stall. This sytem permitted of cheap extraction, and enabled production from localities where other methods could not be employed to good advantage. Thus the pillar-and-stall system, applied to conditions as stated, justified its adoption. Our working seams today, however, are practically all under heavy cover, or are moving in that direction, and with this gradual increase in cover came the increased cost of roadway maintenance. At Princess colliery, the system of pillar-and-stall was followed until roof and bottom conditions became such that further operations were unprofitable, and the longwall method was then adopted as an economic necessity. This fact should be borne in mind when operating costs of both systems are being compared. The longwall method is not held as a cure for all difficulties of heavy cover, but through it these difficulties can be overcome with less expense than by pillar-and-stall. The longwall system of mining, strictly speaking, is one by which a seam of coal is totally extracted in one operation. There are, however, many modifications of longwall, and in some cases it is difficult to determine whether certain practices should be classed as longwall or pillar-and-stall, or a combination of both.

Jan 1, 1928

By William James Kempson

This paper discusses ore handling systems in shafts. These are considered from the loading facility at shaft bottom all the way through to the discharge mechanism in the headframe. These systems will be discussed from the following perspective: i. Intrinsic safety of the systems ii. The efficacy of the systems to perform consistently iii. The maintainability of the systems iv. Overall system cycle times Particular emphasis is placed on the following specific areas: 1. The Shaft Bottom Loading Facilities The various shaft loading systems currently in use are discussed, the selection parameters surrounding these are quantified and the specific selection criteria are outlined. 2. The Various Skip Configurations In this section the various skip configurations in use around the world will be described and the specific design details associated with these will be highlighted. The advantages and disadvantages of these systems will be compared and the overall efficacy of these will be discussed. 3. The effect of the loading and skip configurations on the Load Cycle Times. The overall cycle time which can be achieved by a shaft system is strongly dependant by the speed and efficiency with which the ore can be loaded and transported out of the mine. The potential of the various systems to be optimized will be discussed. The emphasis of this paper is to highlight the lessons which have been learned with respect to ore transport system design and provide a common basis against which these can be compared in future applications.

May 1, 2013

By T. ?kre, O. M. Dotterud, S. Haarberg, J. Thonstad, G. M. Haarberg

An electrowinning pilot plant has been constructed at Falconbridge Nikkelverk A/S, Kristiansand, Norway. The equipment consists of a mixing tank where the electrolyte composition and temperature are controlled, an electrowinning tank equipped with five cathodes and six anodes of commercial size and design and a dechlorination facility. Electrowinning experiments were carried out in this pilot plant using acid cobalt chloride solution from the cobalt tankhouse. Key parameters were varied to obtain an improved understanding of the cobalt electrowinning process, focusing on the detrimental deposition of cobalt oxide on dimensionally stable anodes. The extent of anode scaling was found to be dependent on the electrowinning conditions. Low pH, temperature and cobalt concentration resulted in less scale being formed, however at the expense of cobalt current efficiency and cell voltage, adversely affecting electrowinning production capacity and energy consumption. When operating at high acidity, pH in the anolyte was higher than in the catholyte, which is believed to be due to H+ ions taking part in the current transport across the diaphragm, migrating out of the bags surrounding each anode.

Jan 1, 2005

By M. I. Kalashnikova, Y. M. Shneerson, E. E. Zhmarin, Y. V. Degtiarev, E. M. Vigdorchik

Separation of a magnetic fraction from nickel concentrate following matte flotation, and its treatment in a separate circuit enable reduces precious metals losses. The magnetic fraction is treated in two stages of oxidative leaching: atmospheric and pressure leaching. A study of the atmospheric stage, using mathematical modelling, is described in this paper. The mathematical model and experimental data were used to carry out industrial process calculations. The model enabled extrapolation of the results of batch laboratory test to industrial-scale continuous processing and the selection of optimal process conditions and large-scale equipment. In December 2004, commercial oxidative leaching tests were performed on the magnetic fraction at the Severonickel Plant (Monchegorsk, Russia). A comparative analysis of the mathematical modelling results and the actual process parameters is presented.

Jan 1, 2005

By P. Homola, M. Karlík, M. Slámová

"Aluminum sheets (AA1199, AA8006, and AA5754) were processed by accumulative roll-bonding (ARB) in the temperature range from 20 to 350°C. The microstructure of the sheets was characterized by means of scanning and transmission electron microscopy and electron backscattered diffraction. Mechanical properties were monitored by hardness measurements and tensile tests. Increasing strain (number of ARB cycles) led to incremental development of lamellar microstructure with a decrease of the spacing between high-angle grain boundaries in the normal direction of sheets. ARB process produced an important increase of strength while maintaining thickness and relatively high ductility, without accenting of the anisotropy of mechanical properties of sheets. The level of hardening decreased with the processing temperature and at 300 and 350°C ARB caused even the softening of the material due to the recovery of the deformed microstructure or partial recrystallization during heating to ARB processing temperature.INTRODUCTION Accumulative Roll Bonding (ARB) is a technique of grain refinement by severe plastic deformation (SPD) proposed by Saito et al. (1999). One ARB cycle consists in sheet cutting, surface treatment, stacking of two pieces, heating (optional), and rolling with 50% reduction in thickness. Since the sheet thickness remains unchanged by this cycle, ARB processing can be repeated as many times as desired. The goal of ARB is to impose an extremely high plastic strain on the material, resulting in structural refinement and strength increase without changing specimen dimensions. After several cycles, ultra-fine grained (UFG) materials with high strength and relatively high ductility are produced. An advantage of this method is that it does not require any special equipment as other SPD methods such as equal channel angular pressing (ECAP) (Valiev & Langdon, 2006), high pressure torsion (HPT) (Valiev et al., 2000), or cyclic extrusion and compression (CEC) (Richert et al., 1999), but only a conventional rolling mill and so it is seen as an economically viable and industrially scalable processing route. ARB processing has been successfully applied to various kinds of metallic materials at room or elevated temperatures (Tsuji, 2005). Besides processing single metals and alloys, ARB has also been used for creating ultra-fine grained and nanograined metallic composites (Wu et al., 2010; Qu et al., 2014)."

Jan 1, 2018

By D. P. Wilkinson

Flow field design is critical to determining fuel cell performance with respect to operating conditions. Flow fields are normally designed around their maximum power operating point with the goals of maximizing performance and minimizing pressure drop between the inlet and outlet of the flow field. At lower power pressure drop is reduced, and water management and reactant distribution issues can occur over the active area as well as issues with cell to cell reactant distribution in the fuel cell stack. Flow fields have fixed flow channel geometries and fixed active areas which determine the reactant flow characteristics over the operational range of the fuel cell. In this paper we discuss some of the benefits of a new approach of changing the flow field active area with changing operating conditions. Such benefits for future fuel cell designs could include improved cell performance and stability, improved cell to cell reactant distribution, reduced low current density failure modes, and overall system advantages.

Jan 1, 2005

By C. Caballero, A. Warczok, K. Itagaki, A. Moyano, J. Font

The Codelco Norte Smelter process 2,500 tpd of arsenic-bearing concentrates with an arsenic content of up to 1.5% in one of its two main smelting units, the Teniente Converter. The product, 1,100 tpd high-grade matte or white metal, is traditionally fed to the PS converters, while the 1,700 tpd of slag is fed to the slag cleaning electric furnace for copper recovery. This is achieved in a very reductive environment which reduces the viscosity of the slag and enhances the sedimentation of the high-grade matte droplets. The behavior of arsenic in this non-oxidative environment was studied at lab-scale and fundamental thermodynamic data were obtained. Based on these data a thermodynamicbase model to assess the arsenic behavior in reductive environment was developed. It is based on a mass balance for the reduction and sedimentation stages performed in an electric furnace which allows the recovery of high-grade matte droplets after decreasing the viscosity of the slag. This model can be a very suitable tool for predicting fractional distribution of arsenic in the slag cleaning electric furnace, when the distribution ratio, vapor saturation degree, temperature, y As and pO2 are given.

Jan 1, 2007

By M. Sokoto, H. Hata, K. Nishina, K. Haiki

Fluoride ions in zinc electrolyte cause corrosion to aluminum cathode plates at zinc electrowinning process, so we have developed an iron compound as a fluoride ion adsorbent used in zinc sulfate solution. The iron compound is synthesized from FeC13 solution with a small amount of sulfate ion by neutralizing reaction with Na2CO3 solution. The fluoride ions adsorbed on the surface of the iron compound are desorbed in alkaline solution and the iron compound can be reuse as a fluoride ion adsorbent. Moreover, if adsorption capacity of the iron compound decreases, it can be dissolved in HCl solution and re-synthesized.

Jan 1, 2008

By Masakazu Daté

Moisture effect has been studied for the CO oxidation over Au/TiO2, Au/Al2O3 and Au/SiO2, in the range of H2O concentration over four orders of magnitude. It has been found that the catalytic activity is generally enhanced by moisture in the reactant gas. The enhancement is as large as two orders of magnitude. Response to the moisture concentration, however, depends on the support oxide, indicating different contributions of the support to the reaction steps. The moisture effect is reversible and the activity is mainly determined by the amount of moisture absorbed by the catalyst. The apparent activation energies are not significantly influenced by moisture for Au/TiO2 and Au/Al2O3. On the contrary, non-uniform conversion curves versus temperature observed for Au/SiO2 are drastically changed, which indicates that the reaction over Au/SiO2 does not take place at low temperatures without moisture. The moisture effect may be probably attributed to the decomposition of carbonate species accumulated during the reaction, while the ?OH group might directly participate in the reaction pathways as a promoter.

Oct 1, 2003

By W. S. Urbanski, A. L. Devernoe, R. W. Stuart, M. S. Walker

"Although many investigators have successfully achieved separations using variations of a concept wherein particles are buoyed upwards against gravity in a magnetically attracted fluid, none have succeeded in separating fine particles in a manner that is practical tor mineral beneficiation. This paper describes laboratory tests and preliminary economic analyses for a new mineral separation process which provides enhanced magnetic buoyancy and separation capabilities. The process provides a means of gravity separation in a regime where conventional gravity separation is inadequate; that is for small differences in mineral densities and for very fine particles. Although early interest centers on gravity separation, the process has also been successfully used for precise magnetic separation.Tests were conducted on a variety of mineral mixtures, ore samples and concentrates including; a sphalerite ore, pyrochlore ores and concentrates, cassiterite pre-concentrates, a chromite pre-concentrate, and heavy mineral placer samples. Separations requiring high discrimination between fine particles narrowly different in density or weak magnetic properties were obtained. Of particular interest is the ability of the process to concentrate or remove oxide minerals or gangues, especially silicates. Potential applications are discussed."

Jan 1, 1985

By M. Fafard, D. Picard, J. -F. Bilodeau, G. Soucy

To simulate adequately the behaviour of a Hall-Heroult electrolysis cell, a finite element model must take into account the properties of each material. However, it has some lacking knowledge on the mechanical behaviour of materials, like the long-term visco-elastic (creep/relaxation) behaviour of cathode. A three-dimensional model is then proposed in this paper and will be ready to be implemented in the finite element code FESh++. The model was developed using the three-dimensional model based on thermodynamic of irreversible processes where the choice of the internal variables is based on a phenomenological approach. All parameters of the model are represented by constant constitutive tensors and the temperature and chemical dependencies are taking into account through scalar functions multiplying the constant constitutive tensor. The goal of the first part of this project was to determine the parameters of the threedimensional visco-elastic model at the reference state (virgin material at ambient temperature) of three different cathode materials. This paper presents the theoretical model and the results of creep tests at ambient temperature for the semi-graphitic carbon cathode.

Jan 1, 2006

By J. R. MacDonald

MINING literature contains very few descriptions of operations producing as little as 25 to 30 tons of ore per day. The purpose of this paper is to discuss the gradual development of a mining method for such a small-scale operation at the No. 2 mine of Central Patricia Gold Mines, Limited, and in doing so to review several systems of stoping applicable to narrow ve1ns. MAIN ECONOMIC FACTORS TO BE CONSIDERED (1) Overhead.-The outstanding feature of most mines operating on a single narrow vein is chat of small daily tonnage. The reason for this low output can be readily understood. The strictly limited ore-reserves present a condition unfavourable for a policy of large initial expenditures, with the result that the capacity of the plant provided must be governed by the? amount of ore in sight at the time when mill construction is planned. This is immediately reflected in the cost per ton, there being relatively few tons over which to distributed the more or less static charges, such as hoisting, heating, supervision, administration, pre-production expenses, and other write-offs. (2) Development.-In mining this type of orebody, the main factor contributing to high costs is unquestionably the small tonnage of ore made available by a given amount of development. Thus, for example, from the data tabulated below it can be seen chat, assuming a 12-in. vein and a drifting cost of $9.00 per foot, the development charge for this item alone would be 71 cents per ton. Add to this the charges for raising, cross-cutting, shaft-sinking, and pumping, besides charges arising from development in waste, and the figure will be very considerably higher than 71 cents.

Jan 1, 1941

By F. H. Samuel, J. E. Gruzleski, S. Valtierra, H. W. Doty, N. Andrade

In this work, the age-hardening behavior of cast Al-Si base alloys was investigated. It was found that multiple aging peaks are present in the age-hardening curves of Al-Si-Cu-Mg alloys. TEM observations reveal that the age-hardening behavior is related to the precipitation sequence of the alloy. For the Al-Si-Cu-Mg alloy, the first aging peak is the result from the high-density GP zones, while the subsequent are from metastable phases. The transition from GP zones to metastable phases may be the main reason of the formation of multiple aging peaks.

Jan 1, 2006

By Baisheng Nie

The process of gas diffusion through coal particles and the mathematical physical model under the third kind boundary condition was determined to obtain the rules of gas diffusion through coal particles of different sizes. The analytical solution of the equation was obtained by the Method of Mathematical Physics. The parameters of analytical solutions and the implications of parameters were analyzed. The Biot criterion (Bi) and the Fourier criterion (F0) of mass transfer can represent and reflect the features of gas diffusion field of coal particles. Moreover, the measurement method of gas diffusion coefficient and surface mass transfer coefficient is introduced and an example of measurement is given. The achievement can provide the support to prevent disasters related to methane in coal mines.

Aug 1, 2013

By H. Alzraiee

Traditional planning methods such as CPM and PERT have been useful tools to manage construction projects. However, the underlying model of these traditional methods often seems to fail to represent real projects as they tend to assume no interrelationship between project components. In reality, project components have complex dynamic feedback process that requires modeling of inherent uncertainty in the execution of these projects. Nevertheless, this dynamic nature and uncertainty have not been explicitly addressed by traditional planning methods. Project failure can be attributed to poor representation of the inner and outer aspects of operations that are responsible for project dynamics. Uncontrollable external forces are often cited but the real cause may be internal such as the feedback process among components of the project. An alternative perspective is offered in this paper through system dynamics (SD) that accounts for the feedback process and discrete event simulation (DES) for modeling the uncertainty. The proposed method utilizes SD method for modeling project dynamics and DES method coupled with CPM network for operational details and uncertainty, respectively. A case study that involves preparing engineering drawings in a design office is used to demonstrate the use of the developed method and to highlight its capabilities. Modeling the dynamic dimension is expected to enhance planning and scheduling of construction operations and to provide a better understanding of the impact of various internal and external factors on project schedule and productivity performance.

Aug 1, 2013

By K. S. Coley, M. A. Rhamdhani, G. A. Brooks

Interfacial phenomena in high temperature reactions such as between iron alloy and slag is well documented but not fully understood. It is believed that a gradient of oxygen concentration plays an important role to the occurrence of such phenomena. This article describes the results from the continuation of the study of interfacial phenomena between Fe-Al alloy droplets and CaO-SiO2-Al2O3 slag. Materials characterization techniques involving microscopic observations, depth profiling, bulk, point analysis and were carried out. The roles of oxygen as well as other factors that contribute to the interfacial phenomena were evaluated. The results and their implications to steelmaking will be discussed.

Jan 1, 2004

By J. T. Birkholzer, M. Rutenberg, K. -H. Lux, R. Wolters, J. Rutqvist, L. Blanco Martin

In this paper, we present numerical results corresponding to the Thermal Simulation for Drift Emplacement (TSDE) test, conducted in the Asse salt mine (Germany) between 1990 and 1999 to simulate reference repository conditions for spent nuclear fuel in rock salt. This test is of significant relevance for nuclear waste disposal in salt because extensive research and measurement programs were set up for the experiment. In our numerical study, we use two sequential simulators, TOUGH-FLAC and FLAC-TOUGH, and we investigate two-way coupled processes, focusing on thermo-mechanical analyses due to the main effect of heating. The two simulators used have recently been updated and are able to deal with large strains and creep processes. Moreover, specific constitutive relationships and coupling functions for rock salt and crushed salt under repository conditions are available. Within the framework of a benchmark exercise between Lawrence Berkeley National Laboratory and Clausthal University of Technology, the same scenario has been modeled in three dimensions using the two simulators mentioned. The main objective of the current, first stage of the benchmark is to evaluate the capabilities of these two simulators to predict relevant processes under repository conditions for high-level nuclear waste in saliniferous media. The comparison of the numerical predictions between them is very satisfactory, leading to a successful code-to-code verification. The comparison between measurements and numerical results shows that the most important processes are captured by the codes and constitutive models used. However, some differences exist between measurements and numerical results. These differences will be addressed in the next stage of the benchmark exercise, in which a parameter fitting effort will be undertaken. Overall, from the results obtained it can be concluded that TOUGH-FLAC and FLAC-TOUGH have the necessary capabilities to reproduce relevant processes under repository conditions for high-level nuclear waste in saliniferous formations.

Jan 1, 2015