Search Documents

By P. Farsangi, A. Hara

"Kidd Creek Mines places approximately 10 000 tonnes of consolidated rockfill on a daily basis. Consolidated rockfill is comprised of sized aggregate mixed with different ratio and amounts of binders. Consolidated rockfill, with closely controlled specification, is employed for subsequent pillar recovery and improved passive active/ ground support. With the same amount of cementing agents consolidated rockfill mass yields a higher, compressive strength, modulus of elasticity, cohesion, and angle of friction compared to a typical cemented hydraulic fill mass.The consolidated rockfill at Kidd Creek Mines is designed to sustain not only the gravitational loading of the overlaying fill material, but also to some extent the dynamic loading applied during blasting of the adjacent stopes and/or pillars.The quality control of materials used in Kidd Creek's rockfill system could be effected in three stages of handling: (1) at the surface backfill plant; (2) during transportation; and (3) placement of the fill.The emphasis in this paper is placed on individual stope backfill design and quality control measures at Kidd Creek Mines to place fill in large-scale open stopes which eventually could be exposed on all four walls during pillar recoveries."

Jan 1, 1993

By Hasini Wijayaratne

Anode cover material, a mixture of crushed electrolyte and alumina, is a crucial part of an aluminium reduction cell because of its important role in maintaining overall heat balance. However, until recently little attention has been given to understanding or controlling its composition and quality. The thermal conductivity of anode cover material determines the extent of the heat loss from the top of the cell. This will change as a function of the granulometry and composition of the applied cover as well as over time as the cover material consolidates on top of the cell. The ability to measure or predict the thermal conductivity of fresh and ageing cover is an important tool for managing cell heat balance. Recent studies have shown that granulometry or more correctly, voidage is likely to be the predominant determinant of thermal conductivity of anode cover materials. We have developed equipment to measure the thermal conductivity of granular cover material and tested the relative importance of composition (ratio of alumina to crushed electrolyte) and granulometry/voidage on cover thermal conductivity. In general, our results confirm that granulometry is the dominating factor. Generally, high voidages contribute to lowering the thermal conductivity especially when particles are mostly fine. However the relationships between granulometry, voidage and thermal conductivity are complex due to the varying nature of heat transfer between particles. Aging of granular cover material occur during cell operation forming a consolidated crust due to exposure to heat and fumes over time. Structure and thermal behaviour of this consolidated crust is also important in understanding the overall properties of cover. This paper presents the outcomes of laboratory studies conducted in order to understand the thermochemical behaviour of anode cover material and in particular, the role of fines in anode covers mixtures.

Jan 1, 2011

By Robert B. Parsons

"Draft income tax amendments aimed primarily at certain carve-out arrangements prevalent in the oil and gas industry could have devastating results for long standing royally arrangements in the mining industry . Whether or not this potentially damaging effect is intended is largely beside the points-the point is that the mining industry would be well advised to become familiar with the draft amendments and make sure that the potential damage to existing and future royalty agreements is minimized.The draft amendments fail to take into account the nature of mineral royalties and app ear to reflect a lack of understanding of the characteristics of the mining industry.IntroductionOn July 19, 1985 Finance Minister Michael Wilson released draft amendments to the Income Tax Act which are intended 10 effectively thwart the use of so called “carve-out arrangements"".Unfortunately, the proposed amendments are so broad and far- reaching that countless ""innocent"" royalty arrangements in the mining industry, and in the oil and gas industry, are threatened. The potential harshness of the new rules would be compounded by the retroactive application to the amendments to longstanding royalty and similar agreements."

Jan 1, 1985

By G. R. Baiden

This paper discusses the application of Load-Haul-Dump (LHD) machine teleoperation in combination with a guidance system for single operator control of multiple IJIDs. A system accomplishing these goals has been tested at Copper Cliff North Mine of Inco Limited. This development uses a high-speed, high-capacity production network to teleoperate an LHD during loading and dumping by using 3D video and radio remote control. Following loading, the operator dispatches the LHD using an automatic guidance system to traverse the drifts to the orepass. Remote dumping is done at the ore pass and then the machine returns to repeat the procedure. This has significant productivity gains and improvements in safety. Productivity is improved because operators are involved only in the loading and dumping part of the process. This frees the operators to utilize their time more effectively, loading or dumping a particular machine, while other machines with guidance systems continue to work travelling and/or automatically dumping ore in the ore passes. Safety is improved as the operator is located on a remote control station. Automatic dumping will be incorporated as a future development.

Jan 1, 1994

By J F. Short

The jet piercing process, developed by Union Carbide Canada Ltd., is well established in blasthole production in open-pit mining. By this process, holes can be drilled, shaped and chambered for blasting. In suitable ore or rock formations, a considerable cost reduction can be achieved. This paper reviews the equipment used, relates how cost savings may be accomplished, and concludes with a mention of the most recent developments in this field. JET piercing and chambering, a process for blasthole production in open-pit mining, leads, in many instances, to improved drilling and blasting techniques and costs. It is a method of working rock with a supersonic flame and, to be most effective, depends upon a characteristic of the rock called spallability. Spalling, in this case, is the breaking away of surface particles from the rock body due to stresses caused by the thermal shock of the jet flame. Various rock properties contribute to this action, but, in general, the harder the rock the greater the spallability and the more effective and economical is the jet process. The jet process has the capability to drill, ream, shape and chamber holes for blasting.

Jan 1, 1965

By L. Tapia

The main disturbance for stability in primary grinding using SAG mills is related to continuous changes in the ore being fed to the plant, such as size and hardness. Searching for stability is the first step to accomplish, before trying to maximize the mill throughput. The time variability in the characteristics of the ore being fed from the mine to the plant must be known or inferred to perform adaptive changes in the grinding process control. In day to day operation, such information is not available in real time. Transport times and inventories between the mine and the plant complicate the situation. Under this scenario, Minera Los Pelambres implemented a grinding optimization strategy, based on the real time analysis of certain process variables, such as ore size, mill current consumption, pebble generation and throughput. As a result, both grindability and stability indexes are inferred. This is equivalent to inferring the ore characteristics by knowing its effect on the grinding behavior. These two indexes permit control of the SAG mill total charge level and hence, allow optimization of throughput by means of an expert control system.

Jan 1, 2007

By Zhongxue Li

This paper reviews an analytical model that defines the relationship of weight-weighted or volume-weighted average haulage distance with bench height and other related parameters, presents the optimum bench heights under various conditions in terms of minimizing the weighted average haulage distance of ore/waste during the full lifetime of an open pit mine, and discusses the truck haulage economics of mining open pits by high bench, specifically by 15 m, 18 m and 20 m benches through marginal analyses. The observations from these analyses disapprove the previous conflicting assertions that the over-all weighted average haulage distance either increases or decreases directly with bench height. It is concluded that: (1) an increase of bench height to 15 m from 12 m is likely to be viable under the general conditions of large-scale deep open pit mines; (2) the reduction of haulage cost is much limited with the case of increasing bench height to 18 m from 15 m; and (3) the feasibility of mining open pits by 20 m benches is generally questionable. These conclusions may serve as a useful guide for those who advocate open pit mining by high bench.

Jan 1, 1995

By Geo. D. Furse

"The information that has accumulated regarding the geology of the McIntyre mine is the result of work by several geologists and, as might be anticipated, their conclusions have varied. The writer has been at the mine only a few years and due to wartime conditions has not been able to study and review the mine's geology as thoroughly as his predecessors. Where the writer's conclusions differ from those of previous authors, it should be noted that he has been unable to re-map all the workings in which flow contacts are exposed, but has endeavoured to describe the structure as indicated by the evidence he has been able to observe. He wishes to thank H. G. Skavlem and H. S. Robinson for their constructive criticism of this paper, and McIntyre Porcupine Mines, Limited, for permission to present it. A list of references is appended.The McIntyre mine is in the central part of the Pearl Lake section of the Porcupine gold area. It includes the ""bed of Pearl lake, twenty-two claims to the north of the lake, and the Platt Vet lot to the southeast. It is bordered on the west by the Hollinger and on the east by the Coniaurum property. The chief ore-bearing veins on the upper levels lie very close to the north shore of the lake, but some occur under the lake, and others of lesser importance are found to the southeast. The most important veins are Nos. 3, 5, 7, 10, and 25. Some of the veins extend into the Hollinger. on the west and others cross the east boundary into the Coniaurum. The total production since the commencement of milling in 1912 to the end of March 1947 has been $168,448,218 in gold and silver from the milling of 17,690,963 tons of ore."

Jan 1, 1954

By W. Mirihange

Considerable mechanical property decline is always observed at the Heat Affected Zone (HAZ) of AA 5083, This occurred as a result of the thermal effect on the hardened material, It is highly beneficial to have a prospective metallurgical procedure to overcome this decline of properties. Therefore, experiments were set to evaluate the effectiveness of a quick post weld heat treatment process with the AA 5083, Optimum results were obtained at 473K and with approximately 600 seconds time, The interplay between the time, temperature and mechanical properties are possible to explain by the Lifshitz-Slyozov-Wagner (LSW) theory and by considering the composition of the material.

Jan 1, 2005

By Y. Wang

In this paper, the tribological and electrochemical corrosion properties of Al2O3/polymer nanocomposite coatings were studied using a micro-hardness test, a single-pass scratch test, an abrasive-wear test, and finally an electrochemical technique such as potentiodynamic polarization measurement, The coatings containing Al2O3 nanoparticles showed improvement in scratch and abrasive resistance compared with polymer coatings; this improvement is attributed to the dispersion hardening of Al2O3 nanoparticles in polymer coatings, Corrosion test results showed that the embedded Al2O3 nanoparticles in the polymer matrix do not sacrifice the corrosion resistance of the polymer itself.

Jan 1, 2005

By L. K. Mireku

"Abstract - The Halfmile Lake South Deep zone, Bathurst Mining Camp, New Brunswick, was discovered by Noranda Inc. (Exploration) as a result of a 3-D seismic survey in 1998 and the subsequent drilling of ten diamond-drill cores. The deposit consists of massive, breccia, and stockwork Pb-Zn-Cu sulfide minerals, and is hosted by a volcano-sedimentary sequence belonging to the overturned Ordovician Tetagouche Group. Epiclastic rocks and interbedded fine-grained felsic pyroclastic rocks dominate the stratigraphic footwall. Locally, crystal-rich felsic tuffs and subordinate epiclastic rocks comprise the immediate stratigraphic hanging wall. The entire stratigraphic sequence was intruded by quartz-feldspar porphyritic intrusions, and cut by intermediate and basic dikes. The volcanic and sedimentary rocks can be discriminated geochemically using trace element ratios such as Zr/TiO2 and Nb/TiO2, despite intensive alteration and cleavage development. These ratios indicate that four protolith volcanic compositions exist: rhyolite, dacite, andesite, and basalt. The aphyric and feldspar- and quartz-phyric volcanic rocks are dacitic and rhyolitic in composition; epiclastic rocks have trace element ratios consistent with dacitic compositions. Pearce element ratio diagrams, general element ratio diagrams, and petrographic observations demonstrate that the rhyolitic volcanic rocks exhibit evidence of albite, potassium feldspar, and quartz fractionation, dacitic volcanic rocks exhibit little evidence of any fractionation, and epiclastic sedimentary rocks exhibit evidence of quartz sorting only. Hydrothermal alteration is best represented by the presence of phengitic muscovite and daphnitic chlorite. Minor calcite occurs in the stratigraphic hanging wall, deep in the stratigraphic footwall, and in post-mineralization dikes, and thus is not interpreted to be part of the causative hydrothermal event. Element additions and losses during alteration have been used to determine net alteration reactions, and these have been used to identify alteration parameters that are independent of other forms of alteration and fractionation/sorting, and which can be used to guide exploration. These parameters include: a bulk hydrolysis measure, (2Ca+Na+K-2CO2)/Al; a muscovite alteration measure, K/Al; an albite destruction measure, Na/Al; a chlorite alteration measure, (Fe+Mg-S/2)/Al; a chlorite composition measure, (Fe-S/2)/Mg; a sulfidization measure, S/Ti; and a carbonatization measure, CO2/Ti. With the exception of the carbonatization measure, these alteration parameters define a distinct lateral and vertical zone of intense hydrothermal alteration in the stratigraphic footwall of the deposit, and demonstrate that the epiclastic rocks are predominantly chlorite altered, and the volcanic rocks are predominantly muscovite altered. Within the alteration halo, element additions of Fe and H, and element losses of Na are characteristic. Potassium was added to muscovite-altered rocks, but subsequently removed from chlorite-altered rocks. The results from this study demonstrate that metamorphism and deformation have not significantly obscured hydrothermal alteration signatures."

Jan 1, 2006

By W. D. Fogwill, P. J. Clarke

"The Dawn Lake uranium deposits are located 340 km north of La Ronge, Saskatchewan, in the Athabasca Basin between the Midwest Lake and Rabbit Lake deposits. Four zones of uranium mineralization, called the ""11, 14, 11A and 11B Zones,"" lie within the Athabasca Sandstone, at the sub-Athabasca unconformity and in the basement.At Dawn Lake, approximately 100 metres of Helikian Athabasca Group clastic sediments overlie Aphebian Wollaston Group pelitic and calcareous metasediments and pegmatites. Uranium with some nickel, cobalt and copper, occurs near the sheared stratigraphic contact between calc-silicate gneiss and graphitic, pyritic pelite. The mineralization lies in an area of low magnetic susceptibility which is thought to represent a rock sequence lying stratigraphically high within the Wollaston Group. There is no obvious vertical displacement of the unconformity by faulting, despite considerable brecciation, shearing and slickensides seen in the basement rocks. This suggests horizontal displacement on steeply dipping wrench faults as the main tectonic control along the 11, 11A and 11B trend.Below the Athabasca unconformity, the Wollaston Group rocks are altered to fine-grained mixtures of clays, chlorite and silica commonly called regolith. Along the mineralized trend post-Athabasca fracturing and (or) compaction have occurred through this clay-rich alteration zone, causing the steeply-dipping primary foliation to become contorted. This ""crenulated"" horizon can reach depths of 35 metres below the unconformity and is thickest along fault zones in the calc-silicate rocks. The ""crenulite"" is a distinctive unit which at Dawn Lake is commonly found above pods of ore located deep below the unconformity.Much of the mineralization in the 11A and 11B Zones occurs above, beside and below the thickest part of the crenulated zone, although the crenulated rock itself contains negligible amounts of carbonate, pyrite and uranium. Intense vuggy alteration and collapse breccias are found in calc-silicate rocks deeper and to the west of the 11A and 11B mineralization. There are at least two ages of uranium deposition in the basement zones, shown by small bright cubes of ""pitchblende /"" overgrown and replaced by duller botryoidal ""pitchblende II. ""Sooty pitchblende and yellow secondary minerals are the result of still younger reworking.The geological setting of mineralization, along the contact between carbonate-rich calc-silicate rock and pyritic pelite, suggests that the uranium was concentrated at a pH/Eh boundary located between deeply weathered, carbonate-rich and sulphide-rich basement rocks."

Jan 1, 1986

By D. F. Machuca-Mory

The new algorithm for high-order simulation of ore deposit grades termed HOSIM is based on the concept of spatial cumulants. The algorithm is tested using data from Apensu, a structurally controlled gold deposit in Ghana. The required high-order spatial structures are obtained from a training image or analogue of the deposit. Using the available drillhole data and training image, HOSIM realizations are able to model well the grades and geometry of the large and well sampled mineralized structures. However, under-sampled small structures remain difficult to model. HOSIM offers a promising alternative for the spatial simulation of complex non-Gaussian orebody attributes of interest.

Jan 1, 2011

By L. Xia, B. Hart, K. Douglas1, S. C. Chelgani

Development work to optimize a flotation flowsheet for rare earth element (REE) recovery is underway. The original approach used alkyl phosphates and phosphoric acid ester as collectors to concentrate REE minerals. To improve REE recovery, hydroxamates as alternative collectors were investigated. In this paper, micro flotation of REE minerals using salicylic, benzoyl and naphthoyl hydroxamates is reported. Unlike phosphonic collectors, slime removal does not show a significant effect on REE recovery when using hydroxamates as collectors. Among the three hydoxamates, the grade of La, Ce, and Nd for concentrates produced by salicylic hydroxamate is the highest. The recovery response with naphthoyl hydroxamate is similar to that of salicylic hydroxamate; good grades for La, Ce, and Nd, less effective for Nb, Y, and Zr. The data indicated an affinity by salicylic and naphthoyl hydroxamtes for LREE over the HREE minerals. In comparison, benzoyl hydroxamate indicated an affinity for Nb, Y, and Zr. Temperature effects on REE recovery were also studied. The grade and recovery of REEs generated by flotation using a mix of salicylic and benzoyl hydroxamates at room temperature was almost identical or even better relative to the recovery using naphthoyl hydroxamates at elevated temperature.

Jan 1, 2014

By Maria Skyllas-Kazacos

The All-Vanadium Redox Flow Battery that was pioneered and has been developed at the University of New South Wales (UNSW) in Sydney since the mid-1980s is currently regarded as one of the most attractive energy storage systems for large-scale implementation in a wide range of grid-connected and offgrid applications. Several companies are now manufacturing and installing MW-scale VFBs in applications ranging from renewable energy storage, load-levelling, emergency back-up power and power arbitrage. The full-scale uptake of the VRB in commercial energy storage systems however, is heavily dependent on the availability and cost of vanadium used in the VRB electrolyte. Cost is also a function of purity requirements and although there is little scientific evidence on the effect of impurities on the VRB life and performance, VRB developers continue to demand high purity vanadium at considerable cost. This paper will provide a brief overview of the current understanding of electrolyte impurities on VRB performance together with an economic analysis of the impact of vanadium prices on overall VRB capital and levelised costs for a range of applications.

Jan 1, 2014

By Free. Michael L.

Crushing ore prior to heap leaching enhances mineral liberation and creates fine particles that may require agglomeration to avoid permeability problems during leaching. Conventional modeling is relatively successful in describing general fluid flow and extraction in heaps. However, most models do not adequately account for the effects of mineral liberation and exposure or the effects of agglomeration, curing, and loading on heap leach performance. This paper will discuss methods to account for mineral liberation and exposure as a function of comminution. It will also discuss methods for incorporating liberation, exposure, and mineral locking as well as curing and fluid flow in heap leach modeling. It will also provide information regarding agglomeration and the effect of loading in heap leach modeling.

Jan 1, 2014

By M. Fujikawa

The Kamioka Zinc Smelter was converted from the jarosite process to the goethite process in the year 2000. The reasons for the conversion of the process were that the silica content of the raw material increased and the iron content decreased. The silica easily turns to a gel in sulfuric acid solutions and this causes the solid-liquid separation characteristics to deteriorate. The basic behavior of silica in sulfuric acid solution was investigated and it was found that the goethite process is the most suitable to effectively separate and remove silica from solution. Furthermore, Fe has the capability to remove elements such as Ge that have an adverse effect on zinc electrolysis. This means that, when the Fe content of the raw material decreased, the impurity removal capability also decreased and there was a risk of a build-up of impurities in the process. Iron precipitates in many forms in sulfuric acid solutions. The capability to remove elements such as Ge differs depending on the compound precipitated. Goethite has a higher capability than jarosite to remove elements such as Ge. In this report, the results of applying the process established by investigations of the basic behavior of Fe, silica and Ge in the zinc refining plant are presented.

Jan 1, 2006

By Jorge Loredo, Jesús Garía Iglesias

"Abstract - The Asturian fluorspar district consists of vein and stratiform deposits where mineralization is controlled by a combination of lithological and tectonic factors.It is postulated that these fluorspar deposits have been formed under disequilibrium conditions created during circulation of ascending hydrothermal solutions along faults and other high permeability conduits. Mixing of solutions is inferred from fluid inclusion studies. Cavity filing and replacement processes are very important in localizing the ore deposits and in determining their morphology.Permian volcanic rocks in the area yield a regional positive geochemical anomaly in fluorine implying that Permian vulcanism may be a possible primary source of fluorine.On a regional scale a relationship can be established between some of the ore deposits and important tectonic lineaments. The stratiform deposits preferentially occur within a calcareous-detrital facies located at the margins of basins. These basin margins are related to important synsedimentaryfaults.Fluorite is the only economic mineral in these deposits. Quartz, carbonates, barite and pyrite are comnmon minerals accompanying fluorite. Other minerals that may occasionally be present as minor components are: marcasite, chalcopyrite, fahlore, sphalerite, galena and related supergene minerals."

Jan 1, 1994

By J. Drelich

We report structural forces measured for 10 nm silica particles deposited on alumina substrate and 5-80 nm alumina particles on mica using atomic force microscopy technique. For nanoparticles forming clusters, oscillation of structural forces was recorded with a periodicity that is close to the size of the nanoparticles used. Additionally, selected force-separation results indicate that the forces involved between the AFM probe and individual nanoparticles can be studied using the nanoparticle-coated substrates.

Jan 1, 2006

By R. Ghomashchi

Wear, fatigue and corrosion are the most widely encountered modes of failure in materials used in engineering applications, including aero-gas turbines. Although wear is distinctly classified as adhesive, abrasive, erosive, fretting and so on, there are usually more than one wear mechanism involved in the failure of components in service because there are many systems and materials variables active in materials wear that makes it more difficult to study. This is further complicated by the discrepancies between the results of laboratory tests and field data. The present investigation was set up to examine the wear characteristics of M50 and T1 high-speed steels at both room and elevated temperatures to draw a thorough understanding of the wear behavior of this class of high-speed steels. This article focuses on the mechanical and microstructural characterization of wear for T1 and M50 high-speed steels using a pin-on-disk wear machine.

Jan 1, 2005