Search Documents

By M. Jackman

"Froth stability is critically important for an effective separation of fine and ultrafine particles using column flotation. While a desirable froth stability is required to facilitate the drainage of entrained gangue particles for secondary cleaning, excessively stable froths could create problems in separation efficiency and down-stream processing. In this work, we demonstrate that a stable foam was produced using a poly (N-isopropylacrylamide) (PNIPAM) solution at the temperatures below the critical solution temperature. In contrast, very little foam was produced at the temperature above the critical solution temperature (~32 oC) of PNIPAM. We can also tune the foam stability by changing the temperature of wash water. When warm water of temperature of 50 oC was applied, the foam collapsed and diminished. This is probably attributed to the switching of PNIPAM molecules from coiled to a globule conformation as the temperature is increased. Our results indicate that the foamability and foam stability can be tuned by tempartureresponsive PNIPAM. This is the first time that thermo-responsive PNIPAM has been shown to have potential as a modifier of froth stability in column flotation.INTRODUCTIONIn mineral processing, column flotation has become a more prevalent process in the separation of fine mineral particles (typically < 100µm). Traditional flotation cells are sometimes less efficient in selective separation of ultra-fine particles (Kohmuench et al., 2009). The efficiency of flotation columns is dependent on the froth stability at the top of the cell to drain the unwanted gangue particles entrained in the froth. The greater froth height in flotation columns, compared to mechanical flotation cells, gives a longer froth residence time, allowing more of the drainage process to take place before the froth reports to the launderer. Secondary cleaning, by applying a wash water shower to the froth, enhances drainage of gangue particles entrained in the froth, and improves the recovery of the targeted minerals (Finch et al., 2007).While a stable froth is desirable to facilitate drainage of entrained gangue particles, greater amounts of fine particles have been found to contribute to excessively stable froths which could create problems for down-stream processes (Bethell et al., 2012). Operators have tried spraying additional wash water on the froth, and reducing frother dosage to destabilize the froth and to prevent backup at the launderer. The former is sometimes inefficient, and the latter results in unacceptable recovery loss. Currently, the best practice is often the installation of larger froth launderers, adding expensive defoaming agents, and/or using deaeration tanks (Bethell & Luttrell, 2005)."

Jan 1, 2016

By R. Bruce Ferguson

"The Kettle River Operation of Echo Bay Minerals Company is located about thirty kilometers north of the town of Republic in northeastern Washington State. In tum, Republic is about a hundred and seventy kilometers north and a little west of the city of Spokane, Washington. It is also about fifty kilometers south of the town of Grand Forks, BC, Canada. At this time it is the only gold mining and milling operation in the State.Tailings are stored in a double lined, zero discharge facility. It became evident in mid 1996 that the rate of free water accumulation in the tailings pond was going to result in the level in the pond reaching its permitted freeboard elevation long before the solids plus pore water capacity was reached.We then embarked on a mission to manage tailings pond water on several fronts: reduce fresh water usage in the process, divert spring seeps and surface runoff and install a system to enhance evaporation.IntroductionThe Republic area is an historic gold mining district. Hecla operated its Republic unit from 1892 until closure in 1994. The Kettle River Operation processing plant is located in the San Poi! river valley at an elevation of just under a thousand meters. The facility consists of a ninety thousand ton ore storage pad as the mines are remote and truck haulage is subject to interruption due to weather and road restrictions, jaw and cone crushing with screening, rod and ball milling to an eighty percent passing size of seventy five microns. This is followed by preaeration with high purity oxygen supplied by a vacuum pressure swing adsorption plant plus lead nitrate addition to achieve passivation of the sulfide mineralization such as chalcopyrite, pyrite and pyrrhotite. Conventional cyanide leaching and carbon in pulp adsorption completes the loop. Tailings are treated with air/S02 to achieve cyanide destruction. Plant capacity is 1,815 tons per day. Our license requires that there be no detectable free cyanide in the tailings pond water and a maximum of forty parts per million weak acid dissociable cyanide. The operation started in 1989 with production from the Overlook Mine located about five kilometers further up the same valley at an elevation of twelve hundred meters, hence the location of the mill. Current mine production comes from Lamefoot in the Curlew Lake valley, about ten kilometers distant, and K2 in the Kettle River valley about fifty kilometers away. Both are at an elevation of about 800 meters. Lamefoot produces 1,360 tons per day and K2, 455. Both are underground operations."

Jan 1, 1998

By John Starkey

This paper examines 5 years of SAGDesign testing data with particular emphasis on the grinding test results from two recent projects, the Fortune Minerals Limited NICO project, and the Aurora Energy Resources Inc., Michelin deposits, located in the Northwest Territories and in Labrador respectively. The context is to compare these results with the SAGDesign database. The required SAG mill pinion energy for these two ores showed vast differences, even though both ores had similar average Bond Ball Mill Work Index values - about 13 kWh/t each for the two deposits respectively. Bond Rod Mill Work Index values for NICO ranged up to 19.7 kWh/t for the hardest ore, confirming the harder nature of the coarse material. SAG mill pinion energy to grind the NICO cobalt-gold-bismuth-copper ore from F80 152 mm to T80 1.7mm varied from 16 to 35 kWh/t, while for Michelin uranium ore, it varied from 2 to 9 kWh/t. NICO ore is harder than any other material encountered to date using SAGDesign testing. SAG pinion energy is more than double the ball mill pinion energy using a transfer size T80 of 1.7mm and a final grind P80 of 74 microns. For NICO, the ore is ?off the charts? for simulation design techniques because there is no comparable operating SAG mill treating ore that is this macro-competent. For Aurora, the relationship between SAG and ball mill pinion energy is reversed in that the SAG mill requires less than half of the ball mill pinion energy using a transfer size T80 of 1.7mm and a final grind P80 of 90?. Because these discoveries are so important for grinding mill design, their impact will be dealt with in future papers, at the August METSOC Conference in Sudbury, and at the September SME Workshop in Tucson. It has now been concluded that the ratio of SAG pinion energy to Bond Ball Mill Work Index, is valuable data to use in designing a SAG/ball mill grinding circuit, to help choose the power split needed.

May 1, 2009

By Liu Tao, Wang Wei, Liao Wenjiang, Yang Weiyan, Tang Bin

Side-blown Furnace technology is a developing technology and was developed very quickly in China in recent years, dozens of reference smelters can be found for the treatment of copper concentrate, copper slag, Lead slag, zinc leaching slag and different kinds of slurry. This paper introduces the working principle of the technology, displays the innovations and specifications of China Nerin's SBF technology, gives examples of the typical reference smelters, and looks ahead to future applications. INTRODUCTION Side-blowing furnace smelting process The side-blowing furnace smelting process (SBF process) is one of the bath smelting process with independent intellectual property rights of China Nerin. This process was originally applied to treat copper concentrate and high-lead slag. The SBF process includes two categories, i.e. to treat copper concentrate and to treat industrial solid waste. Up to now, the SBF process has been applied in around 5 million tons of copper concentrate processing capacity and 20+ plants with high-lead slag reduction process. In recent years, SBF process has been gradually used in zinc leaching slag, electroplating sludge, industrial solid waste (e.g., various metallurgical slag), and electronic waste disposal. The basic principle of SBF process is that the material to be treated is directly charged to bath through charging hole with crushed coal and flux, then, enriched oxygen air would be sent to slag level (Vanyukov/Jifeng style furnaces)or matte level (Baiyin style furnaces) via primary tuyere. In this case, the material completes matte/slag metallurgical reaction of gas-liquid-solid interaction under vigorous mixing, and separate matte and slag at the bottom of furnace hearth. With the help of secondary tuyere, the low-pressure air or enriched oxygen would be provided for secondary combustion in the freeboard. The core of SBF process is process parameter control and engineering design of SBF. Presented as a fixed rectangular type, the SBF is a metallurgical furnace consisting of copper water jackets and refractory material. The SBF is consisting of hearth, middle of furnace and furnace top with the sequence from bottom to top. The middle of furnace itself can be further divided into bath area and post-combustion area with primary tuyere and secondary tuyere at both sides. The furnace hearth is made of refractory bricks, which are fused and rebonded Mg-Cr brick, Mg-Cr brick and clay brick from inside to outside. The furnace top adopts a steel water jacket with charging hole and uptake shaft. The water-cooled partition wall is placed at uptake shaft and near charging hole.

Jan 1, 2019

Sustainable Development SAFETY ?Safety is the most important element of sustainability. ?One bad experience or incident can mar a company?s reputation for a long, long time. ?News travels faster than ever ?Internet, blogs, texting, peer-to-peer communication, etc. and unfortunately sometimes the information is not always accurate. ?Rarely do we hear in the news about the mining companies or projects that are done safely ?we always hear about the exceptions. ?Safety is just like TQI / TQM ?the process of improving can never stop.

May 1, 2010

By K. Tada

A surface of a magnesium slab (hereinafter, referred to as Mg slab) or magnesium alloy slab (hereinafter, referred to as Mg alloy slab) becomes black with the use of conventional manufacturing methods. The methods also involve a danger that an explosion of the molten magnesium occurs through contact with cooling water. Thus, it has been impossible to produce a slab having a smooth surface. In the present method, a molten magnesium alloy is supplied into a mold, which is sheltered from the surroundings, from a pool in tundish, which is shielded from the surroundings. AZ31B slab formed in the mold is drawn horizontally out to the outside from an outlet of the mold by revolving of the pinch rolls. A cooling water is jetted at an acute angle onto the slab on the outer side of the mold outlet. Further, an inert gas is sprayed at the inner side of the mold outlet in order to seal in a gap between a free surface of the molten magnesium alloy and a sheltered board surrounding an upper surface of the mold. As a result, oxygen and droplets of the cooling water are prevented from running back to the mold side through the gap. AZ31B slab has a smooth surface condition and high quality without a gas porosity, a segregation or the like. Further, the slab has a size of a width of 100 to 120 mm, a thickness of 5 to 20 mm and a span of 10 m or more.

Jan 1, 2006

By G. B. Hobbs, S. Saimoto, L. Collins

"Plastic yielding and flow in metals is dependent on the microscopic process of simple shear along crystallographic planes and directions known as slip. Thus, by altering the crystallographic direction of the stress axis or placing constraints in the direction of plastic flow, anisotropy of yield strength for the same material is observed. This phenomenon is called texture strengthening. The application of this concept to highly anisotropic crystal structures such as the hexagonal group of titanium and zirconium alloys, the former in missile casing and the latter in nuclear reactor fuel tubing, seems obvious. The outstanding example in cubic structures is the case of deep-drawing steel. The R value, the width strain over the thickness strain during a tensile test, is taken as a measure of texture strengthening. In face-centred cubic structures, texture strengthening has been completely ignored on the basis that materials with R less than one are not amenable to this beneficiation. This study will review two aspects of texture which will lead to strengthening, first the thermal stability of the deformed microstructure, which is dependent on the stress axis, and second, the texture strengthening aspect of fcc metals.A review of recovery and recrystallization in textured aluminum wires, copper and cupro-nickel sheet will be presented with the view of extending these concepts to the manufacture of heat-exchanger tubing. The superior creep properties of specially processed commercial products such as TD-Ni, TD-NiCr and MAR-M200 will be shown to be a manifestation of the same physical phenomena."

Jan 1, 1981

By S. N. Bhatnagar, S. K. Haldar

"Mineral exploration is an expensive speculative venture and calls for optimization of sampling. Exploration is generally planned in grid pattern to be conducted in phased manner. The objective of any such campaign is to assess the quality, quantity and its reliability. The traditional estimation methods are unable to provide a means of calculating the degree of reliability. Application of mathematical models can quantify the precision of estimation and bring forth decision-making criteria at any stage.In this paper three statistical and geostatistical models, viz., Frequency, Probability, and Semi-variogram, have been employed to evaluate sequential exploration data of RampuraAgucha zinc-lead deposit. The optimization in exploration for a specific objective has been highlighted.IntroductionAny exploration campaign demands heavy resource investment starting from the collection of the first sample to the production of the first ton of ore. The best estimation would be if the entire orebody is taken out and sampled. However, this is neither possible, nor desirable. Drilling is the primary tool of geological sampling. It shares the major portion of the investment and, thereby, warrants critical analysis at every stage during the ongoing exploration projects.The exploration program should be conducted as a well planned scheme based on a sequential evaluation approach in a phased way to achieve a specific objective. It would then be possible to evaluate exploration data at the completion of each phase by employing computer-based mathematical techniques to quantify the precision of the estimate for fulfillment of objectives. The subsequent drilling program should be modified accordingly."

Jan 1, 1987

By John F. Vynne

This paper will discuss several of the systems and processes that have been developed over the past few years, and are now being utilized by major mining companies on draglines in North America, Australia and South Africa. These technologies include production monitors and reporting systems, GPS navigation systems, structural integrity monitoring systems, structural analysis studies to increase the dragline RSLs, and inspection and response strategies. The use of these technologies provides significant increases in dragline production, and reduces maintenance costs and downtime. The question that needs to be asked is what value is there in monitoring? Increasing dragline productivity is dependent upon to two items with the overall goal being to maximize the number of bank cubic meters moved and to uncover more coal: 1) maximizing payload and 2) maximizing the number of cycles. If you do not measure and try to optimize the parameters that impact payload and number of cycles, there is very little chance that you can improve overall dragline productivity. These parameters are: Maximizing payload is dependent upon the following: ? Geology ? Blasting ? Monitor weighing accuracy ? Engage location ? Disengage Location ? Rigging ? Suspended load ? Bucket characteristics ? Operator skills ? Minimizing rehandle Maximizing the number of cycles depends upon maximizing digging time, and minimizing cycle and delay/down times by: ? Minimizing Operational Delays ? Minimizing Mechanical Delays ? Minimizing Idle time ? Minimizing Walking time ? Minimizing Fill Time ? Minimizing Swing Angle ? Maximizing Swing & Return Rates ? Minimizing Spot Time A third reason to monitor, conduct structural analysis studies, and have inspection strategies is to prevent catastrophic failures such as shown in the following photographs (figures 1 & 2).

May 1, 2008

By Simon C. Dominy, Patrick R. Stephenson, Alwyn E. Annels

Abstract - The often complex, erratic, and localized nature of gold is a common feature of many vein-style gold deposits. This style of mineralization is often referred to as being nuggety or possessing a high-nugget effect. As a result of these complexities resource estimation is difficult and in general, only Exploration Results can be provided or an Inferred Mineral Resource estimated from surface drilling data alone. Underground development, further drilling, and probably bulk sampling will be required to delineate Indicated and Measured Resources. Tonnages can generally be estimated from diamond drill and development information with a reasonable degree of confidence. Grade is much more difficult to define with confidence because it is commonly highly erratic and discontinuous in nature. The dependency of higher confidence Resource categories on development information may create a Catch 22 situation, with funding for such development often depending on the prior definition of at least Indicated Resources. There are no easy solutions to these challenges posed by high-nugget effect deposits, and it is important when classifying and reporting not to downplay the uncertainties often associated with Mineral Resource and Ore Reserve estimates for such deposits. However, in common with all deposit types, if the principles that underpin the estimation, classification, and reporting procedures are borne in mind and common sense applied, most issues can be satisfactorily resolved. This paper discusses the classification and reporting of Mineral Resources for high-nugget effect gold vein deposits within the framework of the JORC Code (JORC, 1999).

Jan 1, 2001

By Rodrigo Serna, Nora Schreithofer, Zoltan Javor, Kari Heiskanen

"Mineral floatability is a function of mineral properties such as size, liberation, shape, surface composition, reagent coverage on the surface, level of oxidation on the surface, etc.; pulp chemistry: Eh, pH, temperature, DO, reagent type, etc. and hydrodynamic conditions: turbulence, gas dispersion, D32, etc. The biggest challenge with predicting the floatability of an ore is finding a measurement method that would take into account the effect of all of the variables on the floatability of the minerals. The particle-bubble attachment time measurement is considered as an alternative way to predict the floatability of minerals instead of using expensive and time consuming flotation tests because it takes into considerations both surface chemistry and hydrodynamic parameters present in the froth flotation. The existing particle-bubble attachment time method is suitable for studying some significant flotation variables such as pH, temperature, particle size, reagent type and concentration. Nevertheless, measuring the attachment time as a function of collector coverage or surface oxidation is much more challenging. This paper introduces a new induction timer designed to measure the effect of galvanic interaction on the attachment time of particles. The new setup employs an array of needles to create 6 bubbles with the average size of 2.1 mm. Imaging system is used to set the initial distance between the particle bed and the array of bubbles. The attached particles are collected and sent for further analysis. One of the main benefits of the new experimental setup is that the attached particles can be physically separated from the unattached particles therefore many of the particle properties can be analysed and evaluated.INTRODUCTIONSchumann (1942), and Tomlinson and Fleming (1963) proposed that the flotation rate constant is dependent on four probabilities: particle-bubble collision (PC), particle-bubble attachment (PA), particlebubble aggregate stability in turbulent environment (PE), and particle-bubble aggregate stability in froth phase (PF). Any change in any of these probabilities will affect the overall flotation rate constant. All of the above-introduced probabilities are influenced by stream- variables and mechanical variables but their extent of influence vary. The stream variables are particle properties that have been shown to affect flotation rate constant such as size, shape, liberation, mineralogical composition, reagent surface coverage, surface oxidation, etc. The mechanical variables are the direct and indirect properties of the flotation unit affecting flotation rate constant such as cell and impeller geometry, air rate, impeller speed, air holdup, bubble size, residence time, hydrodynamics, froth depth, etc. For instance, the probability of collision is affected by many mechanical variables (bubble size, hydrodynamics, bubbles holdup etc.) but only one stream variable (particle size) has a major effect on it. On the other hand the probability of attachment is affected by much more stream variables: particle size, shape, liberation, surface composition, particle surface oxidation and collector coverage, Eh, pH, etc."

Jan 1, 2016

By S. Kawai

Natural convective flow of the electrolyte solution plays an important role in several electrochemical systems. Copper refining electrolysis is the most important industrial process to produce high purity copper on large scale. Turbulent natural convection develops along vertical plane copper electrodes installed in an unstirred electrolyte accompanying with the electrochemical deposition and dissolution of copper during the electrolysis. It introduces the electrolyte stratification phenomenon. Thus, the electrolyte is circulated in a special way depending on each electrorefining tankhouse. The theoretical discussion is indispensable to understand the coupling phenomenon between the ionic mass transfer rate and the morphological variations of electrodeposited copper. In present study, the mass transfer rate of both Cu2+ and H+ ions as well as the momentum transfer rate is numerically analyzed accompanying with the turbulent natural convection along 1 m high Cu metal electrode surface.

Jan 1, 2007

By M. Amsden

"Since the computer program is far from complete this must be only a brief progress report on the computerization of flotation metallurgy at the Ecstall concentrator at Timmins.Ecstall is currently treating about 10,000 tons per day of two different ore types. One is a low sulphide copper-zinc ore, the other is a high sulphide lead-zinc-silver ore. The concentrator is divided into three individual grinding and flotation circuits. In effect there are three mills under one roof. Normally there are two circuits on copper-zinc ore and oneone lead-zinc-silver ore. At this point in time one of the copper-zinc circuits is under computerized metallurgy control.The first step in this control is the use of an ARL on-stream x-ray analyzer, coupled with a Honeywell 21 computer which types out assays and recoveries for each individual circuit. Our approach to a computer program was to keep it simple. The program was written to coincide as closely as possible to what an operator would do in the performance of his duties based on the in-formation he was getting from the x-ray analyser read-out. Initially, computer control was put on just the copper circuit of the ""A"" Division, controlling the collector addition at three points in the circuit; primary, secondary, and scavengers. The control was based on recoveries and the grade of the copper concentrate. Targets like 95% recovery and 24% copper concentrate grades that it was felt the circuit could achieve were set to start with. It quickly became apparent that this alone was not enough because if on a certain ore the best recovery that could be made was only 94.9% the computer kept calling for more reagents until the circuit was completely out of control. On another ore it might have been quite possible to get 96% recovery but when the set point of 95% was reached the computer stopped trying for any more. To overcome this problem a very simple optimum seeking program was devised by one of the Ecstall staff and it has worked very satisfactorily since being put into use in July 1970.In the copper float only the two collectors R-208 and the xanthate R-317 are under computer control. The addition of frother and depressant is left to the operator. The flotation cells have automatic level controls which can be adjusted by the operator. pH is controlled automatically through a lime loop-sensor arrangement."

Jan 1, 1971

By L. A. Anestiev

A method based on use of calorimetric data for the determination of solidification kinetic parameters is proposed. The method incorporates recent theories of nucleation and growth and allows modeling heat fluxes observed in calorimetric experiment. Statistically optimal estimations of the kinetic parameters, which include the activation&apos;s energies of nucleation and growth, are derived from experimental data by means of nonlinear regression analysis. The method is applicable to pure substances and alloys. The evaluation of the kinetic parameters characterizing solidification of pure Al is used for clarifying and exemplifying the method.

Jan 1, 2004

By J. Kouam

Al-Si-Cu and Al-Si-Mg alloys are widely used in several applications. Although they can be produced near-net-shapes, products made of these alloys very often require some machining. The purpose of this study is to evaluate the machinability of A319 and A356 under TO and T6 conditions. The machinability was assessed using during dry drilling machining process and the machinability indexes used are the chip form, the chip breakability and the cutting forces. It is found that 319 and 356 exhibit different machinability behaviors, especially in the T6-condition in terms of forces requirements, chip breakability and chip segmentation. It is also found that both the microstructure of the workpiece materials and the machining conditions significantly affect the chip formation mechanism, and therefore, the machining parameters could be selected to promote a chip form that is easily manageable in production.

Jan 1, 2011

Inco Limited has been evaluating options for streamlining the overall flowsheet at its Sudbury, Ontario operations to improve productivity and to minimize the cost of at¬mospheric emissions reduction. Some of the flowsheets being considered include vari¬ous levels of copper/nickel separation at the Clarabelle Mill where all Inco&apos;s Sudbury Basin ores are processed. This paper reports on the laboratory and miniplant studies car¬ried out during the flowsheet development for a commercial Cu/Ni separation plant. There are two potential feed streams for Cu/Ni separation. It was determined that Cu/Ni separation from the rougher concentrate requires no regrind, and a very clean copper concentrate is produced, but the recovery of copper is limited to about 70% from ore. Cu/Ni separation is more difficult from the bulk concentrate because of the presence of excess flotation reagents in the slurry and due to locked particles. By replacing the slurry water with clean process water, and by addition of some hydrogen peroxide, entrainment is minimized and excess reagents are removed from the surface, providing a satisfactory separation of copper from nickel. Fine regrinding is required to increase liberation of the locked particles and to obtain 85% copper recovery with minimal nickel contamination of the concentrate.

Jan 1, 2005

By O. Alonso-Gonzalez, F. Nava-Alonso, A. Uribe-Salas, R. Pérez-Garibay, C. Jimenez-Velasco

A current problem in gold production is the presence of copper minerals which dissolve during conventional cyanidation practice. The dissolved copper causes several problems in the different stages of the process. This issue is the base for copper elimination/recovery methods such as the Sulphidization, Acidification, Recycling, and Thickening (SART) process, which is currently used in gold production plants around the world. Even though the process is well established, new challenges appear as the composition of the solution varies from ore to ore, in some circumstances affecting the performance of the SART process. This work presents a thermodynamic study and experimental tests performed to understand the role of the initial copper concentration and sulfur addition, on the efficiency of the copper removal. For a constant cyanide concentration, an increase in the initial copper concentration causes a decrease in copper removal; high sulfur/copper molar ratios favor copper removal. We demonstrated that the cuprous sulfide formed from solutions with high ionic strength, presents better sedimentation rates than solutions with less ionic strength. For solutions with low sedimentation rates, the use of some pretreatment is necessary to facilitate the sedimentation such as addition of flocculants, particle recirculation and the used ultrasonic pretreatment.

Jan 1, 2014

By Zygmunt Wegrzyk

Poland is rich in hard and brown coal reserves, which have become the most important, and steadily developing, primary source of energy. With 192.6 mill. t of hard coal production and 40 mill. t of exports in 1978, Poland is fourth and second in the world respectively. The paper discusses the various mining methods adopted in the country&apos;s history of mining. Particular emphasis is placed on longwails, their mechanization and equipment assembled in the form of fully mechanized face complexes suited for varied geological conditions. Measures to improve the recovery ratio of coal resources are dealt with. investment efforts undertaken in the coal industry are outlined. An account is given of the ever improving techno-economic results of coal mining. The country also exports a wide range of mining equipment and transfers its well-founded technical know-how to others. There are strong cooperative links with many foreign partners.

Jan 1, 1979

By G. C. Weatherly, D. S. Wilkinson, A. M. Limarga

Competition between stress generation and relaxation mechanisms during the oxidation process has been observed. However, the nature of the intrinsic growth stress in thermally grown scales is not well understood. In this talk, we will propose a conceptual model to calculate the intrinsic growth stress based on the analysis of stress-driven diffusional process of oxygen ions along the oxide grain boundary. The calculated stress, which is considered to originate from the constrained lateral expansion of the oxide, is in agreement with a range of experimental observations.

Jan 1, 2004

By Roger D. Plouffe

In today&apos;s mining industry, it is possible to retrieve, from small-diameter holes, geophysical data for qualitative interpretation in exploration and quantitative interpretation in the development of orebodies. The primary objectives in the exploration stage are to identify where, within a hole, economic minerals are, and to help in lithological interpretations. Other aspects, which are more quantitative, are the interpretation of downhole logs for parameters which can be used in surface geophysical methods (i.e. density for gravity surveys, acoustic velocities for seismic surveys, and magnetic susceptibility for airborne and ground magnetic surveys). Recent advances in equipment design, portability and durability have made downhole logging in exploration more inexpensive and reliable. This new equipment is being used to generate very precise quantitative results. This is especially true on uranium development projects. The interpretation of gamma logs for eUJOS values has finally become precise enough that they have begun to replace chemical values in reserve calculations. Another part of development data is density and equilibrium information, which, with today&apos;s technology, is being derived from downhole probing. In the years to come, the trends for many metals are toward neutron activation techniques, or "in-situ assaying", and the use of multiple logs for better lithological and physical rock property determinations.

Jan 1, 1981