Search Documents

By J. W. M. Porritt, K. C. Cheng

Knowledge of radon emanation rates from uranium-bearing rocks is essential to the design of mine ventilation systems for uranium mines. Measurements of equilibrium ratio between radon and its daughters in mine air are important for a better control of mine radiation conditions. The concentrations of radon and daughters were monitored at cut-and-fill stopes in the Beaverlodge Mine of Eldorado Nuclear Ltd. during all phases of the mining cycle. The radon emanation rates of ore and rock samples were measured at the laboratory and the results were compared with in-situ emanation tests in an isolated ore drift. Samples of backfill solution, backfill drainage and ground seepage water were measured [or radon and analyzed for radium and uranium. The results showed that discharges of backfill solution and daily shift-end blasts were the two major sources for a rapid release of radon gas in the ventilation air. Other mining operations, such as drilling, mucking, etc., contributed little effect on radon release to the mining environment. Radon emanation rates of the Beaverlodge are samples ranged from 13 x 10-18 to 600 X 10-18 Ci/cm2/ sec and that of waste rock samples from 0.54 x 10-18 to 13.4 X 10-18 Ci/cm2/sec. The in-situ emanation rate of mine walls with ore-to-rock ratios of 1 to 7 was 60 x 10-18 Ci/cm2/sec. The average equilibrium ratio of radon and its daughters in stapes was 32.6%. Under a normal ventilation condition, the average background levels of radon concentration in cut-and-fill stopes ranged from 13 to 80 pCi/L. The discharges of backfill solution during backfill operations at 100 tons solids per hour released approximately 1.8 x 106 pCi/min of radon and elevated radon concentration in stapes 2 to 5 times above the background levels.

Jan 1, 1981

By Enrique Rubio

Several mining operations are currently evaluating the feasibility of changing their mining method to Block Caving. There will also be several deep low-grade ore bodies that will face the need to go underground in following their ore to depth. There are two main reasons why Block Caving is attractive: firstly, it offers the lowest operating costs amongst all the mining methods; and secondly, it is truly a massive mining method, offering the highest potential production capacity. Despite its longstanding popularity, there are still significant components of the method that are not clearly understood. Also, the lack of availability of key geomechanic information still presents a major obstacle to developing mine planning and production scheduling. There are several key issues in block caving that can make it feasible such as cavability, fragmentation, stresses will condition the way that a block caves and the way that material is drawn from the draw points. Consequently Block Cave mining method is a good example where the ore body has to be related to design and mine planning. The concepts of dilution, draw control as well as sequence definition are reviewed in this paper to illustrate the idea of integration. There have been some examples of mines where some of the components of mine planning have not been integrated causing a disaster in terms of economics or safety. Different layouts configurations might give a different result in the planning of the mine

May 1, 2002

By B. N. Church, A. R. Pettipas

"The second vertical derivative method of processing aeromagnetic data from low level helicopter surveys yields results correiatable with the known geology and may be utilized to indicate possible targets for future exploration in the Silver Queen and Equity Silver mines areas, near Houston in central British Columbia . The principal zones of alteration associated with mineralization, known from detailed mapping, are further delineated and extended in a way not possible by a cursory examination of the original magnetic data.IntroductionThe second derivative method of processing aeromagnetic data is a long established procedure used to enhance the short wavelength content of the magnetic fields. Some recent exam pies of the use of the second derivative technique have been published by Chandler (p. 385), Sun Yunsheng et al. (p. 424) and Yarger (p. 223) in Hinze, 1985. According to theory, the ""second vertical derivative"" is closely related to the rate of curvature of magnetic (or gravity) fields and is particularly useful in resolving and sharpening local anomalies. The contours on second derivative maps may coincide with important features such as lithological boundaries, faults and mineralized zones.In the Houston area, central British Columbia, aeromagnetic data supplied by local mining companies provide a ready base for analyses. Examples are data sets for the Silver Queen and Equity Silver mines centred 35 km and 34 km south and southeast, respectively, from Houston (Fig. 1), (Cochrane, 1970 and Church, 1985)."

Jan 1, 1990

"INTRODUCTIONThe Department of Energy, Mines and Resources has recently developed two automatic controls for use in the cyanidation circuits of Canadian gold mills. These controls are the alkalinity probe and the Continuous Cyanide Titrator both of which are discussed in the paper ""Instrumentation in the Cyanide Process"".(1)In May 1966 these process controls and associated recording equipment were installed in the Bralorne mill by two Scientific Officers from the Department. The object was to determine if the equipment was amenable and applicable to this particular circuit. The purpose of this paper is to discuss the performance of the equipment over a test period of 4 months.CONCLUSIONSThe results of test work to date indicates that both the Conductivity Probe and the Continuous Cyanide Titrator would be an as set to the operation of the Bralorne mill.The conclusions are generalized as follows:-(1) At a milling rate of 100, 000 tons per year the expected reductionin reagent consumption would give a direct saving of 37, 660 lbs of lime@$0.030 per lb and 15, 790 lbs of sodium cyanide@ $0.175 per lb. Such cost savings would pay for the equipment and installation costs within a 30 month period"

Jan 1, 1967

By C. Zangerl, T. Strauhal, S. Perzlmeier, M. Holzmann

"In high mountainous regions, deep-seated rock slides are often observed in foliated metamorphic rocks such as paragneisses, micaschists and phyllites. Given that comprehensive investigations of deepseated rock slides are extraordinary costly and therefore are rare, most studies are related to investigations in the surroundings of infrastructures and human settlements. In the framework of this study there is an excellent opportunity to gain new insights in the fundamental processes and mechanisms of slowly moving deep-seated rock slides from a case study in the surrounding of a large dam reservoir in Austria. New fundamentals for comprehensive slope stability analyses and hazard assessments and sound prognoses focussing on the long-term stability and deformation behaviour of slopes under changing boundary conditions (e.g. impounding of a reservoir) and/or concepts for mitigation measures can be obtained. Within this contribution, geological field surveys, deformation monitoring, geophysical and drilling data were analysed and presented. Based on the compiled and analysed data, some key-properties of the rock slide will be presented, whereby special attention will be given on the geometry and internal structure, the slope kinematics, as well as hydrogeological and geomechanical aspects.INTRODUCTIONIn high mountainous regions, deep-seated rock slides are often encountered in highly foliated metamorphic rocks such as paragneisses, micaschists and phyllites (Agliardi et al. 2012). Critical situations may occur when deep-seated rock slides fail in a rapid manner characterised by very high sliding velocities, and/or when they develop into long run-out rock avalanches. However, many rock slides in foliated crystalline rock masses either do not move at high velocities nor do they accelerate seriously and form extremely rapid slides. Displacement rates in the range of a few millimetres or centimetres per year are common for this type of rock slide (Bonzanigo et al. 2007, Tentschert 1998, Watson et al. 2007). Nevertheless, some case studies show an activity behaviour characterised by acceleration phases reaching velocities of even metres per day. However a slope collapse is not expected and these slopes decelerate to much lower base activities. The trigger for these phases can be manifold and include heavy rainfall and snow melt, initial reservoir impounding and water level fluctuations, changes in the slope’s equilibrium state due to antecedent slow deformation processes, ongoing erosion processes along the toe of the slope, and others (Zangerl et al. 2010)."

Jan 1, 2015

By W. G. Wahl

The Slave Province, a segment of Archean continental crust, migrated west and north from the northern flank of the Superior protoshield shortly after the Kenoran orogeny. The probable cause of migration, the path it followed and the cause of its coming to rest can be inferred from the Bouguer gravity data. The migration caused an indentation in the edge of the Superior protoshield which precluded the development of the Hudsonian orogenic front under Hudson Bay. As the nickel and asbestos deposits of the Thompson Nickel Belt and the New Quebec Nickel Belt are restricted to this orogenic front, no such deposits would occur under Hudson Bay.

Jan 1, 1973

By R. Niechcial

As populations grow and industry expands, the limited fresh water resources available are increasingly under stress. This situation creates conflict between communities and industry; and the sustainability of both is threatened. The symbiotic relationship between community and industry highlights the need to develop innovative solutions to these water shortages. The sea may hold the key to providing the resource to permit the development of industry, the sustainability of communities, and the protection of the dwindling legacy water resources around the world. Desalination technologies have developed to where it is now economically viable to create industrial and potable water quality from seawater. Nowhere is this development more important than in the arid region of Northern Chile, where high copper prices have encouraged a boom in mine development.

Jan 1, 2007

By E. L. Jones

THE concentration of tin in the tailing from Sullivan ore has been de-scribed by H. R. Banks, superintendent of the Sullivan concentrator, in a paper presented at the annual meeting of the B.C. Division of the Institute in October, 1941(1). The reduction of the concentrate EARLY EXPERIMENTAL WORK Experimental work on the smelting of Sullivan tin concentrate was done in Trail. Preliminary tests in the laboratory indicated that the concentrate could be successfully treated in an electric furnace. A small electro-thermic pilot plant was built and, at the same time, reduction tests were made in an oil-fired reverberatory furnace. Both types of treatment gave satisfactory results. It developed that no fluxes, other than those already in the ore and in the ash of the reducing agent (either coke or coal), were needed. By using an excess of iron, a complete recovery of the tin in the slag was obtained, but with 20 to 30 per cent iron in the tin. A counter-current treatment was thus indicated, viz., the primary slag was first treated with hard-head (iron-tin alloy) from the refining and final slag smelting, producing tin with 2 to 4 per cent Fe. This secondary slag was subsequently treated with scrap iron to produce tin-iron alloy, and a final slag low enough in tin to waste. By following this line of endeavour, a tentative flow-sheet was drawn up and a successful operation was established. Without resorting to electrolytic refining, a metal comparable in purity to standard tin was produced. Metallurgical results and operating costs were found to be very similar with an electric furnace or a fuel-fired furnace. 'However, electric furnace smelting was chosen because the furnace required was smaller, and because some doubt existed as to the cleaning of the final slag in the reverberatory furnace reduction.

Jan 1, 1944

By Tiago Webber

Mineral resources estimation comprises basically two stages: (i) data collection, analysis and validation, and (ii) the estimate of the grades and tones of the deposit. The most applied method for sampling survey in mineral exploration is rotary drilling with total core recovery. High drilling costs make borehole geophysical logging attractive to obtain the maximum possible information from each borehole helping to understand ore intersections, grades variability, limits of the deposits and continuity of the mineralization. In this paper, borehole geophysical logging was used to enhance the sampling survey and to derive grades indirectly (without lab analysis) with a certain amount of uncertainty. Indicator kriging (IK) was the estimation method used, as it is adequate to incorporate the uncertainty associated with the geophysical derived grade values. The results were compared to the conventional procedures using grades determined via core analysis and ordinary kriging. Borehole geophysical logging proved to be efficient to define the essential features of ore deposit and IK provided results with acceptable precision and accuracy if compared to the model provided by ordinary kriging.

Oct 1, 2009

By Seunghoon Lee

The increase in the number of higher and larger buildings is expected to require the buildings' outer wall maintenance process, which includes cleaning, painting and monitoring, still depends on manpower. In this study, we proposed the robotic building maintenance system and aimed to reduce the jerk effect through the motion control of the system, improve the performance of the maintenance task, and ensure longer life and safety by improving the stability of the building structure and robot system. Through the results of the motion control and field-test with the proposed system, in specific, horizontal sliding module (HSM) showed that the jerk oriented by impact force was significantly reduced, feasibility of the proposed method was verified, and the robotic challenges were explored.

Aug 1, 2013

By B. J. Fryer, R. P. Taylor

"As a monitor of the processes involved in the formation of granitoid mineral deposits the coherent group behaviour of the rare earth elements (REE) actively reflects changing fluid characteristics. For example, in the porphyry environment, magmatic-hydrothermal fluids produce potassic alteration with strong enrichment in the light rare earth element s (LREE), reflecting their high pH, low fluid/rock ratios, and the dominant role of CI- complexing in metal (i.e. Cu, Au) transport. With increasing fluid/rock ratios and decreasing pH accompanying the progressive involvement of meteoric fluids (and the production of propylitic, argillic, and phyllic alteration) anionic species such as F - and CO, 2- become important in metal (e.g. Mo, W,) transport through complexing, and their activity in the hydro thermal fluids is illustrated by mobilization of the heavy rare earth elements (HREE).The relative involvement of CI- versus F - versus CO32- in metal transport in other granite-related systems can also be monitored through REE behaviour. Hence granitoid tin-tungsten mineralization and associated greisenization typically exhibit heavy rare earth enrichment and evidence the importance of F' and CO32- in metal transport. Similarly, heavy rare earth element enrichment in hydrothermal uranium deposits can be related to the transport of uranium as carbonate complexes. REE are widely accepted as powerful tools in the study of rock petrogenesis, but their use has been neglected in the investigation of mineral deposits. The recognition of the systematic variation of REE distributions in granitoid mineral deposits suggests that the application of REE geo chemistry, particularly when integrated with fluid inclusion and isotope studies, can provide (1) an effective method for identifying the physicochemical controls of metal transport and (2) a useful criterion for elucidating metal distribution."

Jan 1, 1983

By D. G. Macintyre

"Potentially economic stratiform barite-sulphide deposits have recently been discovered in Devonian basinal facies rocks of the Kechika Trough of northeast British Columbia. This new mineral district is over 180 kilometres long and includes nine major occurrences, namely Driftpile Creek, Bear, Mount Alcock, Cirque, Fluke, Pie, Elf, Kwadacha and Sika. The Cirque is the largest known deposit, with reserves of atleast 30 million tonnes averaging 10per cent combined lead-zinc and 47 grams per tonne silver. The footwall rocks for the Cirque and other strati/rom barite-sulphide deposits in the area are rhythmically bedded baritic and pyritic carbonaceous black shales, siliceous argillites and cherts of probable Mid to Late Devonian age. These siliceous rocks overlie a succession of proximal to distal turbidites which are the basinal equivalent of Early to Mid Devonian carbonate reefs to the east. The siliceous facies is overlain by deeper-water black shales of probable Late Devonian to Mississippian age.Preliminary stratigraphic and sedimentological investigations suggest that the strati/arm massive pyrite and bedded barite deposits formed in third-order euxinic basins within a northwest-trending structurally controlled trough which, in the southern part of the district, was bounded by carbonate reefs. The exhalative event, which appears to have been accompanied by synsedimentary faulting, took place during the early stages of a major eastward-directed marine transgression that was probably related to rapid crustal subsidence. Dewatering of metal-enriched shales and subsequent brine discharge along fault zones within the trough, with the exhaled brines accumulating in seafloor depressions, is the mechanism envisaged for formation of the deposits. Convective circulation systems may have been established about the more deep-seated faults, in response to elevated heat flow levels."

Jan 1, 1982

By Peter A. Hacquebard

"The early history of the Geological Survey of Canada is closely connected with coal geology investigations in the Atlantic Provinces. In 1843, Sir William Logan, the first director of the Geological Survey, measured the 4441m thick shore section at Joggins in Nova Scotia. Detailed mapping of the coalfields were subsequently carried out by H. Fletcher during the latter part of the nineteenth and first part of the present century. During the 1920-1940 period, the stratigraphy of the carboniferous WIZS' established by WA. Bell, who later also became a diretor of the Survey. Bell's work WIZS' followed by coal geology investigations of A.A. Hayes, W.S. Dyer, EA. Goranson, G. W.H. Norman, J.E. Muller, T.B. Haites and P.A. Hacquebord.The activities and accomplishments of the Survey geologists during the past 150 years are presented in this paper.General Outline of Survey Activities in Coal Geology During the Past 150 YearsIn 1842, when the Geological Survey of Canada (GSC) was established, the industrialization of the major countries of Western Europe and North America was actively persued. The energy required for this industrialization was obtained from the only fossil fuel then available, namely coal. The measure of a country's major mineral wealth at that time was the availability of mineable resources of coal. Eastern Canada, where mining had been carried out since 1720, was known to be well endowed with valuable coal deposits. In the major fields of Nova Scotia (Fig. I) several large-scale operations had been started during the middle and latter part of the nineteenth century.The significance of coal, therefore, was well understood, and exploration surveys specifically oriented toward coal were carried out by the Geological Survey from its earliest beginning. The first report of a detailed geological description of the coal measures of eastern Canada was prepared in 1843 by Sir William Logan (1845), the founder and first director of the Geological Survey of Canada. This early work was continued and complemented in 1896 by H. fletcher (1906), who during the latter part of the nineteenth century and first part of the present century systematically mapped the coal-bearing regions of Nova Scotia, which he considered all to be of approximately the same age."

Jan 1, 1992

By Jian Deng, Haitian Sun, Zengqian Hou, Shuhe Song

"Abstract - Volcanogenic massive sulfide (VMS) deposits, an important base-metal deposit type in China, occur widely in submarine volcanic districts of variable magmatic affinities. These VMS deposits range in age from Archean to Mesozoic, but most are in Proterozoic and Paleozoic sequences. More than 60% of VMS deposits formed in the Paleozoic, the most important metallogenic eon. Three important Paleozoic VMS-metallogenic provinces include Northern Qilian, Sanjiang and Altai provinces. The Proterozoic constitutes the next important era, but with no VMS deposits in the middle Proterozoic. VMS deposits associated with the Proterozoic volcanic rocks occur around the Yangtze Platform and in the western Kunlun-Qinling. The Triassic is third in importance, with VMS deposits concentrated in the Sanjiang Tethys. The Archean has only one VMS deposit, on the northern margin of the Sino-Korea Platform.Five distinct compositional classes of Chinese VMS deposits have been distinguished: Cu, Cu- Zn (or Zn-Cu), Cu-Fe, Zn-Pb-Cu, and Pb-Zn (-Cu). The Cu, Cu-Co, and Cu-Zn types of deposits occur sporadically from the Archean to Paleozoic, and are closely associated with mafic and ultramafic volcanic sequences. The Zn-Pb-Cu and some Cu-Zn type deposits are restricted to the Paleozoic and Triassic, and are hosted by calc-alkaline felsic rocks in bimodal basalt-rhyolite sequences, whereas Cu-Fe and Pb-Zn type (except for the Laochang deposit) deposits are restricted to the Proterozoic and occur in calc-alkaline volcanic sequences. As large quantities of marine mafic volcanic rocks were deposited in western China, Cu and Cu-Zn deposits are major types of Chinese VMS deposits.Chinese VMS deposits formed in a wide range of paleo-tectonic settings and depositional environments, such as island-arcs, rifts, aulacogens, and ocean ridge hot spots. Among these, the rift and back-arc environments are the most important, containing about 60% of Chinese VMS deposits. Aulacogens are a subordinate environment where most of the Proterozoic VMS deposits formed. The oceanic ridge and hot-spot systems are common in the tectono-magmatic domains in China, but contain only a few small Cu and Cu-Zn type VMS deposits.The Chinese VMS deposits have usually been influenced by both deformation and metamorphism to various degrees, resulting in changes in the shape and metal distribution. Seven representative deposit styles have been recognized: sheets, sheet plus strata-bound stringer, cyclically zoned deposits, mounds, mound-like deposits, strata-bound stringer-disseminated, and stockwork-disseminated deposits. The formation of these various styles of deposits is controlled by several key factors, such as lithology and permeability of the host rocks, focused or unfocused discharge, temperature and chemical composition (e.g., salinity) of hydrothermal fluids, as well as depth of seawater."

Jan 1, 1999

By D. François-Bongareon

"In previous publications by the author, significant advances and generalizations of the theory of sampling of broken ores, prompted and confirmed by experimental results, have been presented. This paper shows how to implement these theoretical results in practice. The models to be used are reviewed, with a description of the various sampling parameters involved. Then the methodology for the experimental assessment of those parameters, including segregation factors, is described in simple and practical terms, along with the use of handy sampling protocol charts. Finally, the particularly important case of processing data from a sample-tree experiment is detailed, and examples of applications covering all situations and types of experiments are provided.IntroductionThe reliability of a sample of crushed material , i.e. the expected (average) deviation between its true grade and the true grade of the lot it comes from, mostly depends upon six factors:• the size (mass) of the sample (and to a minor extent, for small lots, the size of the lot);• the size of the rock particles (degree of comminution)• the nature of the mineralization at microscopic scale (i.e., within even the smallest particles);• the geological nature of the mineralization and mineral of interest;• the grade of the lot in the mineral of interest; and• in some cases, the state of segregation of the lot.In practice, one should first disregard segregation problems, and assess sample variability in the segregation-free case. Once the numerical parameters governing this variability have been assessed, then segregation factors can be assessed in turn. In the case of laboratory standard sample preparation procedures, segregation can usually be disregarded altogether."

Jan 1, 1993

By P. K. Kaiser, S. Maloney, S. Yazici

"This paper focusses on the strength or capacity of cable bolts and introduces a new perspective for cable bolt design by demonstrating that mining-induced stress changes may affect cables in a detrimental manner. The concept underlying a novel cable bolt pull-out resistanceor bond capacity model is described and its practical significance is demonstrated by application to a simple two dimensional scenario of a fall-of-ground.A number of practical implications emerging from the application of this model are discussed to provide guidance to ground control personnel jar improving cable bolt support systems in mining applications. These include cable layout optimization, use of cable pre-reinforcements, assessment of embedment length requirements, need for plated cables (or straps), use of bird-caged cables (or buttons), and grout quality issues.IntroductionDuring the last decade, cable bolting has become a standard support technique in mining for handling wide spans, reinforcing are passes, preventing or reducing dilution of ore in marginally stable stopes, and for many other rock support need s.In its infancy, many deficiencies in cable bolt supports resulted from improper installation techniques and, in particular, grout quality control problems and the use of empty breather tubes (Goris, 1990). The development of special grout pumps and fail proof placement procedures (Oliver, 1992; Bourchier and O'Flaherty, 1992) have eliminated many of these early problems. Nevertheless, there are still situations where cables seem to lose their capacity during mining, and in these cases the cables do not provide the expected and needed ground support. In some instances, cables perform extremely well, whereas in others the same support layout and quality of support installation seem to be insufficient, allowing falls-of-ground or progressive cavings to occur."

Jan 1, 1992

By J. Bouchard, M. Levesque, D. Georges-Filteau, P. Radziszewski, G. LeBlanc

"Grinding mills are infamous for their extremely low energy efficiency. This paper reports the results of an investigation that characterized energy outputs in industrial grinding mill circuits. It identifies and discusses the potential for recovering energy from grinding circuits. Agnico-Eagle Goldex Division, Mine Canadian Malartic, and New Gold New Afton Mine participated in the study by providing operating data for three semi-autogenous grinding mills and four ball mills. Results showed that on average, 79% of the supplied electrical energy was converted to heat absorbed by the slurry, 8% was lost through the drive system, and approximately 2% was transmitted to the ambient air. Only 9% of the input energy was actually used for grinding. The remaining 91%—wasted as heat—could potentially be recovered using suitable technologies or integrated energy management systems. This topic remains to be further investigated. ¦ KEYWORDS Comminution processes, Energy recovery potential, Grinding mills RÉSUMÉ Les broyeurs sont tristement célèbres pour leur rendement énergétique médiocre. Cet article présente les résultats d’une étude qui caractérise les rendements énergétiques des circuits industriels de broyage et examine les possibilités de récupération d’énergie dans les circuits de broyage. La mine Goldex d’Agnico Eagle, Mine Canadian Malartic et la mine New Afton de New Gold ont participé à l’étude en fournissant des données de fonctionnement pour trois broyeurs semi-autogènes et quatre broyeurs à boulets. Les résultats montrent qu’en moyenne 79 % de l’énergie électrique fournie sont convertis en chaleur absorbée par la pulpe, 8 % sont perdus dans le système d’entraînement et environ 2 % sont dispersés dans l’air ambiant. Seuls 9 % de l’énergie primaire sont, de fait, utilisés pour le broyage ; les 91 % restants (perdus sous forme de chaleur) peuvent potentiellement être récupérés à l’aide de technologies adaptées ou intégrées dans des systèmes de gestion de l’énergie. Cette question demeure toutefois ouverte. ¦ MOTS CLÉS broyeurs, potentiel de récupération de l’énergie, procédés de comminution INTRODUCTION Grinding is largely recognized as a very inefficient process; energy efficiency estimates range from < 1 to 2% (Fuerstenau & Abouzeid, 2002; Tromans & Meech, 2002, 2004) when comparing the input energy to that required for generating new mineral surfaces. Criticizing an “ill definition of the reference for the output energy,” Fuerstenau and Abouzeid (2002) proposed a “more meaningful baseline” would be “the energy for producing new surface area by the ¬mens.” Based on this reference, they concluded that “the ball mill is reasonably efficient energetically,” exhibiting an efficiency of approximately 15% for quartz."

Jan 1, 2019

By Hiroyuki Sano, Hiroshi Chida, Katsuya Toda, Takafumi Sasaki

Saganoseki Smelter & Refinery is one of the largest copper producers in Japan to produce 450,000 tons of new copper annually. Saganoseki used to operate six PS converters with "4 Hot-2 Blow" scheme, but managed to change its operation to "3 Hot-2 Blow" scheme with four PS converters, while maintaining the same production capacity. To achieve the operational change, the following improvements have been carried out; 1) Extending service life from 220 to 350 batches, 2) Shortening cycle time by increasing the blowing rate and the matte grade, 3) Reducing environmental impact by applying sophisticated fugitive gas collection system and 4) Saving energy by waste heat boiler’s modifications. The operational change has been successfully executed, and results in drastic productivity increase and cost reduction. Currently, Saganoseki is maintaining the efficient and consistent operation with 4 PS converters. This paper describes the above-mentioned improvements for increasing productivity and the recent operational conditions of the PS converters.

Jan 1, 2015

By A. Fawceit, B. C. Dyer

"The basis of the tomographic velocity imaging technique is briefly described and an application of the method to detect and image a cross-section through a chromite pod is presented. Using the chromite application as an example, the relative costs of tomographic data acquisition and processing are compared with those of diamond drilling to obtain similar resolution. A number of different tomographic survey configurations and the potential role of the method in surface and underground exploration are discussed.IntroductionThe technique of seismic tomography has been most widely applied in oil industry exploration, nuclear waste disposal, civil engineering site investigations and in the assessment of the condition of mass concrete structures. Although model studies had indicated that tomography would be a useful tool in mineral exploration, relatively few applications have been reported.Essentially the method relies on the determination of the speed with which sound travels through a region within a cross-section of the earth or large body. The speed of sound is determined by the physical characteristics of the medium through which it is passing. In geophysics the speed of sound is generally referred to as the seismic velocity. Due to variations in the formations of different rocks the seismic velocity will vary and so can be used to map geological boundaries"

Jan 1, 1994

By Yihan Liu, Jintao Zhang, Chen Xiao, Xiaomeng Zhao, Guanglei Song

To estimate the performance of the inert anode materials based on NiFe2O4 spinel ceramic during it used for aluminum electrolysis, we investigated the wetting process of cryolite molten salt which is in composition of industrial aluminum electrolysis with carbon anode and NiFe2O4 based cermet materials, by means of determination the interface wetting angle between the molten cryolite electrolyte and the solid anodes interface. The results show that the wetting angle between the electrolyte and carbon anode is larger than 90 angulation, this means that they basically can not wetting; however the nickel ferrate spinel ceramics behaves much better. In regard to the NiFe2O4 matrix materials, their initial wetting angles is 76.9. The initial wetting angles for 1.0wt%MnO2, 2.5wt%TiO2 and 0.5wt%V2O5-doped samples are respectively 56.86°, 52.98° and 51.93°. However, after 50s later, all the wetting angles came down below 15°.

Jan 1, 2015