Search Documents

By Tweedy. D. H.

"The paper describes the rapid development of, and operational experience in the utilization of, pneumatic low-pressure pipeline hoisting systems to vertically convey raw coal and rock through shafts, supplementing shaft capacity-the greatest lift to date being 535 m.A typical installation has raised over 250,000 tonnes in less than one year from a depth of 413 m through a 350/ 400-mm pipeline at a rate of 85 tonnes per hour. Operational experience on seven systems has provided valuable data on performance and operating costs.The main advantages of the systems lie in the flexibility of the pipeline to occupy existing free space in shafts and underground roadways, the relatively low first cost, the short delivery and installation time, and the economical running cost.Conclusions are therefore reached on future applications for example, the use of boreholes in older mines where new production technology has outstripped shaft or slope capacity, inter-level hoisting to implement concentration on transport roads and perhaps full mine output from relatively small mines.IntroductionIt is seven years since the basic art and practice of the pneumatic hoisting of minerals was described. The technique was developed in Western Canada by Radmark Engineering and found favour in the United Kingdom with the National Coal Board. Engineering and commercial feasibility trails were conducted in collaboration with the Mining Department and Mining Research and Development Establishment of the N.C.B. There was also considerable involvement with the British Health and Safety Executive.During the last five years, rapid progress has been made in the installation of new systems in the United Kingdom, Hungary and other countries. The operational experience gained makes it possible to report ""in depth"" on these installations, which cover a wide range of different physical mining applications."

Jan 1, 1982

By S. Feinstein, I. Reznik, Y. H. Hatzor, O. Shitrit, Y. O. Rosenberg, H. J. Vinegar, S. Nguyen

"We report the effects of porosity and total organic carbon (TOC) content on the mechanical behavior of organic-rich chalks, based on laboratory measurements. The organic-rich chalks are from the Senonian Ghareb and Mishash formations. This deposit is an immature oil-prone source rock, about 300 meters thick, situated at shallow depths (several hundreds of meters) in the Shefela basin in central Israel. The study is based on core data collected from the Zoharim borehole.Three main phases comprise the bulk volume of this rock: 1) carbonate mineralogical phase (predominantly calcite); 2) pores (mostly saturated with brine); and 3) solid organic phase (type IIS kerogen). The mechanical effects of porosity (23-45%) and TOC (4-19%) are evaluated based on bulk incompressibilities vs. volumetric fractions analysis. Volumetric fractions of mineralogical and organic phases were obtained by porosity, density and TOC measurements. Saturated rock bulk moduli were measured through ultrasonic velocity measurements. Saturated rock bulk moduli correlate best with the sum of kerogen and pore volume fractions, rather than each of them separately. The volumetric fractions were also used to define the range of bulk modulus of the organic-rich chalk, using the Hashin-Shtrikman upper and lower bounds. Based on Marion's Bounding Average Method (BAM), the normalized stiffness factor of the chalk averaged at w=0.197, indicating a soft pore geometry. Using the average normalized stiffness factor, the BAM predictions showed excellent match with the saturated rock bulk modulus and the sum of kerogen and pore volume fractions. Based on our findings, it is inferred that kerogen grains do not support the solid skeleton but are distributed between the minerals grains. We also propose here a straightforward approach for calculating the Hashin-Shtrikman bounds, based on TOC and porosity measurements. The mechanical effects of porosity and TOC indicated here are very important for the understanding of the influence of immature kerogen presence in highly porous chalks, as the Ghareb and Mishash formations."

Jan 1, 2015

? A BARGE WILL BE INSTALLED IN THE BOTTOM OF A COMPLETED PIT. ? THE PROVEN BAUER CUTTER TECHNOLOGY WILL BE INSTALLED ON THE BARGE AND A DEWATERING PLANT WILL BE INSTALLED NEAR THE BASE OF THE PIT RAMP. ? THE WATER LEVEL IN THE PIT WILL BE RAISED BY 20- 40 METRES AND REMAIN CONSTANT OVER DURATION OF MINING. ? THE CUTTER WILL BE LOWERED TO MINE 10 METRE DEEP BENCHES ON A CHECKERBOARD PATTERN TO AN ULTIMATE DEPTH OF 200 METRES. ? THE 5? MINUS CUTTINGS WILL BE PUMPED TO THE DEWATERING PLANT, DEWATERED, AND TRUCKED TO SURFACE.

May 1, 2003

There are many inherent risks in creating a mine plan for a new ore zone in an underground mine; one of such risks is the redistribution of stresses that could be a cause of instability. Using numerical modelling tools, it is possible to model the planned stope extraction sequence and evaluate the influence of mining induced stresses on the stability of remnant pillars, and use this information to remedy potential setbacks. This paper demonstrates this approach through a case study of the short-term mine plan of the Lapa mine of Agnico Eagle Mines Ltd., an underground gold mining operation near Val d?Or. Three-dimensional boundary element modelling is used to compute the stresses induced by the stope extraction sequence as planned with a longitudinal retreat mining method. The proposed methodology can be generalized to other mines that require an understanding of the stress concentrations at the pre-feasibility stage of mine design.

May 1, 2009

By R. G. Rosehart, S. Y. Lee

"The current investigation concerns the removal of arsenic from waste waters using ion-exchange resin and activated carbon as sorption media. Use of certain weak and strong base anion exchange resins permits the removal of arsenic. Arsenic may be loaded on the weak base resin in the pH range of 2 to 3 and on the strong base resin above pH 5. The elution of arsenic is successfully achieved using 0.5 M NaCl or a mixture of NaCl and NaOH. The activated carbon investigated was less effective on loading arsenic, but the arsenic loaded was easily eluted by simple pH adjustments."

Jan 1, 1972

By A. Taylor

This paper considers mineral processing in zero gravity dry environments typical of asteroids or comets. The electro-dynamic separation technique using pneumatic flow systems is explored. Pneumatic delivery of solids is used because of extreme temperature changes and the possible scarcity of water. The present earth-based process and how it can be modified for these conditions is examined.

May 1, 2001

By E. Brouillette

Difficult operating and mining conditions such as low visibility, difficult roadbeds, fast cycling, small openings, and sharp corners create high demand for LHD manoeuvrability and operator dexterity. Operator experience and patience is especially solicited to fill the bucket rapidly and efficiently and performance can be particularly affected by the skill level of individual operators. Teleoperation and automated loading are viewed as options to improve overall equipment and operation performance in certain mining conditions. Comparative statistical measurements of autoloading performance in different production environments at Noranda demonstrate an increase in bucket filling efficiency and a reduction in filling variance, allowing LHD operation to be more consistent and within manufacturer specifications. Consequential cost savings and productivity increases are demonstrated to be transferable to other mining situations.

May 1, 2003

By M. A. Bérubé, M. Choquette, P. W. Godbehere

"RESUMELa scorie produite par le procédé pyrométallurgique d'extraction Noranda contient environ5% de cuivre. Elle est traitée comme un minerai conventionnel de cuivre au concentrateur de Mines Noranda et les rejets de flottation présentent encore des teneurs souvent supérieures à 0.3% en cuivre. La scorie est principalement constituée de magnétite, de fayalite et d'un verre siliceux. Bien sûr, Ie cuivre y est majoritairement sous forme de sulfures et d'un peu de cuivre métallique. Le verre contient toutefois un peu de cuivre en solution, de 0.14 à 0.33% en moyenne, selon l’echantillon examine, ce qui représente à peine 1% de tout Ie cuivre de la scorie. Dans les rejets de flottation, cela justifie par contre de 15 à 25% des pertes totales en cuivre, Ie reste se retrouvant sous forme de tres petits globules de sulfures de cuivre ou de cuivre métallique, en moyenne de 2 à 3 micromètres de diamètre et bien emprisonnes dans Ie verre.SUMMARYThe slag produced by the Noranda continuous smelting process usually contains about 5% copper. It is processed as a conventional copper ore at the concentrator of Noranda Mines. The flotation tailings still often contain more than 0.3% Cu. The slag is mainly constituted by magnetite, fayalite and a siliceous glass. Evidently, the copper occurs mostly as sulphides and, to a lesser extent, as metallic copper. However the glass contains a small amount of this metal in solution, between 0.14 and 0.33% on an average, depending upon the investigated sample. This represents scarcely 1% of the total copper in the crude slag, but as much as 15 to 25% of this metal in the flotation tailings, in which the major part of the copper occurs as very small globules of copper sulphides or metallic copper with an average diameter of about 2 to 3 um and well-locked in the glass."

Jan 1, 1987

By D. Seo, P. Au, X. Husang, D. Nagy

The production of single crystal (SX) turbine blades represents the current stateof- the-art in Ni-based superalloy design. With complex casting processes and alloy composition modifications, SX superalloys exhibit superior high temperature mechanical properties to their polycrystalline counterparts. Stresses and plastic deformation can occur in SX nickel-base superalloy engine components at various stages during their manufacture and use. For examples, stresses are created during initial solidification and also during solid state processing such as shot peening, grit blasting, blending, electrodischarge machining and welding. Stresses may also be created during service due to random events such as foreign object impacts. Subsequent exposure of SX to high temperatures during solution heat treatment and brazing repair can result in recrystallization which has been shown to be detrimental to both creep rupture strength and fatigue performance of the components. It is therefore the objective of this paper to understand the recrystallization behavior of two SX superalloys, PWA 1484 and 1483, subjected to pre-stressing and subsequent heat treatments.

Jan 1, 2006

By Gary Raymond

The Similkameen Division of Newmont Mines Limited operates a low-grade open-pit copper mine in southern British Columbia. The copper mineralization is extremely erratic.As a result, over seven years of operation, ore control methods have evolved from standard flagging based on blast-hole assays, through an in-pit grab sampling system, to the present method of mining to computer-determined ore-waste boundaries based on geostatistics. These improved ore control methods have resulted in a gain of at least 25% on ore tonnage miffed, at the same grade as obtained using earlier techniques. At the same time, geostatistical ore reserve estimates are now within 7% of milled ore tonnage and grade on a yearly basis, whereas the original polygon ore reserves under-estimated mineable ore tonnage by 15% to 45% and over-estimated grade by about 20%. The author discusses why traditional ore estimation methods give poor results in erratically mineralized orebodies and describes the geostatistical approach to the problem.

Jan 1, 1979

By A. Tikhonov, D. Kipper, V. Korovin, A. Olifirenko, Yu. Shestak

The present paper deals with vanadium and molybdenum sorption from industrial wastes and intermediate processing products using Cybber macroporous strong- and weak-base anionites. Vanadium and molybdenum recovery by Cybber anion-exchange resins as well as desorption processes were studied in static and dynamic modes; their efficiency was demonstrated for that purpose. The results of the work may be used to design technologies for complex processing of both ores and industrial wastes containing vanadium and molybdenum.

Jan 1, 2011

By James A. H. Church

This paper is in the nature of a protest against the dangerous propaganda afoot for the prevention of new mining undertakings and which is based on the imaginary 'blue ruin' conditions supposed to exist in the industry. An article by Mr. G. R. Pratt, A.M.E.I.C. in the first issue of the Western Canada News, February 2nd, 1925, and entitled "Review of Coal Mining in Alberta", is an excellent example of this type of propaganda. The article is a tissue of misstatements, faulty deductions and erroneous conclusions. For instance it contains the statement that some coal measures in Alberta are mined at great depth - whereas we all know that there is no coal mined at great depth anywhere in the province; another error is the classification of all mines under one head irrespective of whether they are mining prospects, 'country banks', or pukka mines equipped with railway facilities; and I believe that suppressio veri is tantamount to suggestio falsi. The bulk of his article hinges on a Table 1, which shows the details of coal produced in Alberta during 1923. Studying this table Mr. Pratt, in the manner of a conjurer producing rabbits from a hat, offers the following for the confusion of the public:- (1) "Waste effort, want of capital, waste of coal resources which result from unrestricted development"; the fact being that the waste is due to the failure of the Department of the Interior to exercise the powers which are inherent in the form of lease.

Jan 1, 1925

By P. Bacher, L. Dubourg, M. Jahazi, G. Dezaise

Effect of friction stir welding parameters and natural ageing on weld properties are reported. Using a Taguchi design of experiment, attempt is made to systematically examine the influences of the welding speed, tool rotation speed, forge force, tilt angle and pitch ratio on the weld size and ultimate tensile strength of FSWed joints. One millimetre thick plates of AA7075-T6 were welded in lap joint configuration. Samples were characterized by optical microscopy, hardness and tensile measurements. Trends suggested by the results and directions for further investigation are discussed.

Jan 1, 2006

By Carl Edmunds

Talk Outline Deposit?s Vital Statistics and Economic Environment Regional Geologic Setting Deposit Geology UBC Research Search Model and Current Exploration Plans Kemess Operations Kemess South Mine Mining rate (2006) ?135,000 tonnes / day Mill throughput (2006) ?52,000 tonnes / day Average Annual Production ?300,000 oz gold and 75 million lbs copper ?Production until mid-2009 Kemess North > Open pit reserve 423.8 million tonnes @ 0.3 g/tgold and 0.18% copper > 4.1 million ounce gold reserve (127 tonnes) > 1.45 billion pound copper reserve (636,000 tonnes) > 0.75:1 Strip Ratio

May 1, 2006

By M. Seyed Ahmadi

This study investigates the role of nitrogen gas injection in the dissolution rate of Si into liquid Al. A unique revolving liquid metal tank was used, with a capacity of 50 kg of liquid Al. Experiments without gas injection have shown that the dissolution of Si increases as the bath superheat and the tangential velocity of the liquid Al increase. When injecting nitrogen gas at flow rates between 0-5 lit/min in the vicinity of the solid Si, results so far clearly show greater dissolution. In addition, results on the role of the gas flow rate relative to the position of the nozzle are presented and analyzed.

Jan 1, 2011

By B. A. McKee, T. Adamcewicz

For a capital expenditure of only $46,000, Caland Ore Company has successfully converted its three dry grinding center peripheral discharge rod mills to dry grinding ball mills. The conversion has resulted in a significant capacity increase, operating cost reductions and in-plant environmental improvements. This paper describes why and how• the conversion was made.

Jan 1, 1972

By A. C. Munro

The concrete work on the new Britannia mill was started in April, 1922. The erection of steel commenced on July 10th, following. The installation of wood work and machinery , began on November 4th of the same year and was pushed to completion in January, 1923. The new mill building is an all steel structure enclosed with galvanized corrugated steel. All main floors and foundations are of reinforced concrete, which makes the building practically fireproof throughout. The mill building rises on a steep hillside to a vertical elevation of 210 feet and has seven distinct floors, for the various opera-tions. Only one elevator, with 30-foot centres, is used in the entire mill. The building is exceptionally roomy and well lighted, both by day and night. The capacity of the mill, as originally designed, was to be 2000 tons daily, but this tonnage can be readily increased to over 3000 tons daily by making slight changes in the fine grinding equipment; in fact, an average of 2700 tons per 24 hours was maintained throughout the month of September.

Jan 1, 1923

By T. Patching

"Introduction The occurrence of coal was first reported in the Drumheller area in 1793 but it was not until 1912 that production of coal was recorded. In that year 13,000 tonnes were mined in the Drumheller area. Three years later the Drumheller mines ranked next in the Province to those in the Crowsnest and Lethbridge districts, with an output of 225,000 tonnes. By 1917 production had increased to 600,000 tonnes, moving Drumheller to second place in output in the province, second only to the Crowsnest district. It held this rank until 1960. Production, almost all from underground mining, rose to over a million tonnes a year by 1920 and remained between one and two million tonnes per year until 1954. Competition from newly discovered oil and natural gas, beginning around 1950 caused a steady loss of domestic coal markets, especially from underground mines. By 1960 Drumheller's production had fallen below a half a million tonnes per year and the field ranked third in output in the province, being surpassed by new stripping operations in the Castor field. By 1965 only a couple of producing mines remained in the Drumheller valley, and output was only about a quarter of a million tonnes per year(1). Throughout the life of the field production was seasonal, depending mainly on the domestic heating market. In 1979 the last mine ceased production. For the last several years of its operation it had remained open in the summers to provide tours for visitors(2). The Drumheller mining operations were located along or near the Red Deer River valley which is 300 to 400 feet deep, and extended from a few miles above the city of Drumheller to East Coulee, about 13 miles down the river in a south-easterly direction. Intervening mining communities existed for some years at Wayne and Rosedale. During the peak years of production some 2000 to 2500 miners and their families lived in these communities and the surrounding areas."

Jan 1, 1985

By E. C. Goodhue, R. D. Coleman, I. E. Puddington, A. F. Sirianni

Iron ore samples containing apatite are fractionated to acceptable products by spherical agglomeration methods. The phosphorus is upgraded by a factor of 10 at an elevated pH. High-grade iron products are obtained in good yields from the tailings in a second step of the operation. The grade of the phosphorus separated appears to reach a maximum at about pH = 10; recovery of iron decreases below about pH = 4. Both the recovery and grade of iron are found to be reduced sharply above about pH = 8.

Jan 1, 1968

By S. Haggarty, R. Walton

Barrick's growth and development plan will add three major new mines during 2005 including the Lagunas Norte Project in the La Libertad Province of Peru, the Veladero Project in the San Juan province of Argentina, and the Tulawaka Mine in north¬western Tanzania. Lagunas Norte and Veladero are similar in that they are both green-field open pit deposits at elevations over 4,000 meters above sea level, with two stage crushing and heap leaching followed by Merrill Crowe zinc precipitation for precious metal recovery. Operating sites will each generate in excess of 700,000 ozs Au per annum with commissioning and full scale operation planned during the third and fourth quarter of 2005. Details with regards to regional geography, development schedule, production and process specifics for Lagunas Norte and Veladero will be discussed in this presentation providing an overview for the respective properties.

Jan 1, 2005