Search Documents

By W. D. Freeborn

Slim-hole drilling and completion techniques were first used in the Cynthia area of the Pembina field, Alberta, by the Texaco Exploration Company in the summer of 1957. Prior to that time, eighty-eight wells had been drilled and completed in this area in a conventional manner. Subsequent to the initial four-well evaluation programme, twenty-one additional wells have been drilled using slim-hole techniques. No difficulty was encountered in the drilling and completion of slim-hole wells, or in obtaining production from them. A comparison of drilling and completion economics and practices has been made for slim-hole and conventionally completed wells. Penetration rates for both bit sizes (614 in. and 9 in.) were relatively equal. The shorter life of the smaller bits required the use of 15 per cent more bits per well, but the total trip time to change bits was similar for both hole sizes because of the higher hoisting speeds possible with the lighter drilling strings used in the slim holes and better hole conditions. Completion costs of the slim holes were reduced by 37 per cent as compared to the costs of conventional-type completions. This was made possible through the use of smaller well equipment, the elimination of tubing, and a reduction in rig time for completion operations.

Jan 1, 1958

By Eugene F. Mehr, Dennis C. Martin

"Development of the final slope for the 340 m (1200 ft) high hanging wall at Cassiar Mine precipitated an area of deep seated instability involving an estimated 17.6 million tonnes. The deformation mechanisms involved squeezing of soft deformable serpentinite rocks in the toe which caused planar sliding and graben toppling of the stronger sedimentary rocks in the middle and upper sections of the slope. Although movement rates up to 150mm/day were recorded, by understanding the controls on failure, the mine was able to install a suitable monitoring system and complete the open pit with only minor loss of the mineable ore. Accelerated mining was required in the last full year of operation. This paper describes the deformation behaviour, failure mechanisms and back analysis results for the failure. The monitoring systems and operational aspects related to the failure are also presented.IntroductionCassiar Mine is located in steep mountainous terrain in northern British Columbia approximately 1200 km north of Vancouver (Fig. I). During the final mining phase of the open pit, instability developed in the approximately 340 m high hanging wall (east wall) slope. A unique graben toppling mechanism was identified based on detailed assessment of slope monitoring data and visual observations. Comprehensive slope monitoring enabled mining to continue even though movement rates as high as 150 mm/day were being recorded. Three-dimensional limit equilibrium back analyses and numerical modelling have been used to assess the various controls on the slope movements and to understand the failure mechanism."

Jan 1, 1993

By Jan Butra

In copper ore mines located in the Pre-Sudeten Monocline the deposit mining using room and pillar systems has been carried out for more than forty years. When implementing mining systems in deep copper ore mines it appeared to be necessary to adapt them to variable geological conditions and natural hazards. In the initial period of exploitation there were mainly caving and rockburst hazards. The adaptation of room and pillar system was connected with a state of knowledge in the scope of identifying, forecasting and controlling rock mass hazards. The new solutions allowed the safe and efficient exploitation of a blanket deposit of variable thickness from about 2 to 15m, seated on progressively increasing depth. They included exploitation in constrained conditions, such as in protective pillars. In the exploitation period, technical and organisational activities aimed at rockburst hazard control were introduced including active methods for controlling rockburst hazard and procedures for conducting mining works in the rockburst hazard conditions. When mining at a depth exceeding 1,200 m, the exploitation method and technique are additionally affected by thermal hazard and by gas and rock breakout hazard. New solutions of the room and pillar system and a longwall system with mechanical mining have been developed for exploitation in the associated hazard conditions. The require application of many innovative solutions in the scope of mining process and ore haulage mechanisation, excavation support and forecasting and control of existing hazards. The main purpose of these solutions is to conduct the safe and economically effective exploitation of the deposit.

Aug 1, 2013

By A. K. Debnath

The water resource is key to survival of the mankind and this resource is now becoming critical in many parts of globe including India. As per an assessment of Central Ground Water Board (CGWB) of India, a huge shortfall of about 58 billion m3 of water is anticipated by the year 2050. In order to counter this shortfall, there is thrust from Government of India to adopt water conservation measures. National Environment Policy, 2006 of Government of India also stresses upon the need to take up water conservation measures for water security of the country. The coal mines in India provide an excellent opportunity to take up water conservations measures therein. The mine water is not acidic unlike western countries and it conforms to the prescribed regulatory standards. This nature?s gift is utilized in Coal India Limited by allowing mine voids to get filled with mine water. The net recharge potential of the opencast mining area is found to be about 5% in comparison to 2% in non-mining area offering good prospects for ground water recharge. The seasonal rainwater is also diverted into mine voids left at the end of mining operations which act as huge reservoirs/ pit lakes for storage of the water. They also serve as surface water bodies for recharging of water table in the surrounding areas. The area and space left from where coal has been extracted completely in underground mines and will not be entered by any man or machinery after the extraction, called goaf, are also potential source of water conservation. These additional water resources created are being utilized for meeting the industrial, domestic, irrigation and other requirements of the projects and local communities eliminating the need to tap other fresh water resources including ground water. Presently, 75% of the water demand of the coal mining project is being met from the water stored in the mine pits. In future, CIL is likely to create about 3.3 billion m3 of water resource, on an average, in its opencast mines alone. In the mine closure plan of opencast mines, the last cut is proposed to be developed into water body for recharge of ground water and creating additional water resources. A clean potential source of potable water is thus developed after mine closure. This will ensure water security of the country.

Aug 1, 2013

By R. Prioul, J. Kear, D. Chuprakov, A. P. Bunger

"Hydraulic fracture (HF) growth through naturally fractured rocks challenges the development of accurate predictive HF models. The authors present laboratory experiments differentiating behaviours associated with orthogonal and oblique intersections between HFs and natural fractures (NFs). HFs were created in sandstone and crystalline (gabbro) rock specimens, impinging orthogonally or obliquely on an unbonded machined frictional interface. Ultrasound monitoring was used to observe the rate of propagation through the interface. A contrast was observed between direct and offset crossing for orthogonal and oblique intersection, respectively. The stresses required to promote crossing depended on the intersection angle between HFs and NFs.RÉSUMÉ La propagation des fractures hydrauliques (FH) dans les roches naturellement fracturées pose un défi pour le développement de modèles prédictifs. Nous présentons des essais en laboratoire qui différencient les comportements associés aux intersections orthogonales et obliques entre les FH et les fractures naturelles. Des FH ont été créées dans des spécimens de grès et de roches cristallines (gabbro), heurtés de manière orthogonale ou oblique sur une interface machinée, non liée, de frottement. Un suivi par ultrasons a servi à observer le taux de propagation à travers l’interface. Un contraste a été observé entre un croisement direct et un croisement indirect des intersections respectivement orthogonales et obliques. Les contraintes requises pour promouvoir le croisement variaient selon l’angle d’intersection entre les FH et les fractures naturelles."

Jan 1, 2016

Bahuerachi Project Characteristics Why it?s nicer at Bahuerachi Mexico is a mining country Low political, regulatory and trade risk Low social/permitting risk Proximity to infrastructure Road Power grid (8 km) Rail line (25 km) High grade zones (skarns), CRD and near surface oxide component are sweet spots to the overall system. Size of low grade system points to potential long mine life?and numerous new targets developing. Timelines-2006? 90 to 100 combined RC and core holes to go! MAIN ZONE Drilling ? Goat ?Finish Mid April ? Main Zone, going North, depth of testing dependent, estimated for May ? North Lobe-May ? Commission independent resource estimate by May 06 for results of first pass drilling to date ?tonnesand grades ?Main Zone Milestone. ? Continue infill or expanded drilling to July (minimum) ? 1stpass RC scheduled until September OTHER Targets ? Begin drill testing North Skarn target Mid-April, minimum 5 drill holes, 1,000 meters. Ongoing expansion of target with surface work (mapping) ? Road to Colome(Skarnin north of Main Zone) as part of porphyry program ? Tule(southern) porphyry and skarn system-soils and mapping OUTSTANDING events Metallurgical report on floating and leaching tests (Sulphide/oxides).

May 1, 2006

By R. F. Robertson

"Adsorption isotherms of hexyl mercaptan vapour on synthetic sphalerite, zinc sulphide and zinc oxide were de-termined with a gravimetric McBain-Baker micro balance incorporated in the B.E.T. apparatus. Isotherms are given for hexyl mercaptan on synthetic sphalerite at 25°C, 0.5°C and 50°C; on zinc sulphide at 25°C and 1.5°C; and on zinc oxide at 25°C. All these isotherms are sigmoidal, with a definite change in slope at or close to the mono-layer. The amount of mercaptan adsorbed below the monolayer increases almost linearly with relative pressure to P/P0 = 0.8.Above this value, the amount adsorbed increases very rapidly with relative pressure. Hysteresis loops appear in the isotherms for all adsorption-desorption cycles. These loops are completely reversible. It is not possible to desorb the mercaptan monolayer from any of the adsorbents, even at elevated temperatures."

Jan 1, 1966

By Jian Li, Robbie McDonald, David Robinson

"The pressure oxidation of sulfide minerals at temperatures above 200°C enables the extraction of base metals, improves the extractability of gold from refractory ores, enables solubilisation of PGEs and can be used to hydrothermally upgrade base metal-containing feeds. Fundamental studies reveal that the solution chemistry (and mineralogy of the solids) during pressure oxidation can be manipulated with outcomes that include (1) increased leaching rates, (2) lower oxygen requirements and (3) the formation of chemically more stable residues. This paper presents examples describing how these outcomes might be achieved based upon fundamental investigations.INTRODUCTION The application of pressure oxidation to the processing of gold ores and concentrates dates back several decades and continues to be the process of choice at operations such as Pueblo Viejo (pyritic gold) which host the largest autoclave of its kind in the world (Barrick Gold Corporation, 2016). Commercial application to the processing of base metals and PGMs resides with long established processes such as the Sherritt process, ore specific applications such as by Noril’sk, at Sepon etc. or has not proceeded to date beyond pilot scale testing (e.g. Phelps Dodge, CESL, Activox, Platsol). Recently there has been significant interest in hydrothermal upgrading options for concentrates including the NONOX and Toowong processes (Rohner et al., 2016; Weidenbach et al., 2016). The latter options suggest directions where sound knowledge of the underlying fundamentals enables novel outcomes and efficiencies to be obtained. It comes as no surprise that investigations similar to those underpinning these developing processes can be traced back several decades. It is not the subject of this paper to provide a historical perspective of the relevant autoclave chemistries but rather, to present some potential opportunities suggested by studies in our laboratories. Topics to be discussed in this paper include (1) control of metal extraction rates, (2) control of iron-residue composition and (3) control of sulfur oxidation and hence acid generation and oxygen requirements. The work described will focus upon the pressure oxidation of a nickel concentrate."

Jan 1, 2017

By G. M. Ritcey, V. M. McNamara

"In the processing of gold ores by the cyanidation route, effluents which are discharged to the tailings areas can contain up to several hundred parts per million of cyanide in complex combination with similar quantities of heavy metals. Complicating this obvious problem of waste control are concentrations of thiosalts and thiocyanates which are roughly equivalent to the amounts of cyanide species. Although most gold mills are located in thinly populated areas, such contaminants can represent a potential environmental problem due to the various limitations exhibited by on-property ponding.The former Extraction Metallurgy Division of CANMET recognized the problem and, in early 1974, invited representatives of the gold mills to Ottawa to discuss the situation. At that meeting members of the Division presented a ""state of the art"" literature survey of cyanide abatement technology for waste solutions, together with preliminary cost estimate data(1). Shortly thereafter, Environment Canada, together with Environment Ontario, decided upon a guideline of 0.1 ppm (0.1 mg/l) total cyanide content as tolerable for an effluent stream which is discharged, in any manner, to the watershed."

Jan 1, 1978

By G. R. Sadowski

"Large subhorizontal joints have been found in the foundation excavations in basalt and granite of Brazilian Dams. Some spread for hundreds of square meters showed slickensides—polished surfaces plus striations—and laminations interpreted as related to shear displacement, what substantially reduced their shear strength and imposed special reinforcement measures against the potential sliding of overlying concrete structures. The geological characteristics of these discontinuities have raised speculations related to their origin, be it related to mechanisms of bulging, cambering or to some tectonic or primary geological event.Several geologists and engineers from the northern hemisphere including Terzaghi already showed to be concerned with their role in granite foundations while in the southern regions Brazilian authors have found similar occurrences but also affecting individual lava flows of continental flood basalts in the foundations of major dams of the Parana Basin, which they designated under the particular name of “fault-joints”. This double-standard designation is self-explanatory of the difficulties involving their origin and related geomechanical properties: faults or just shear joints?Recently, similar features were encountered in the foundations of large dam constructions in anorogenic granites inserted in the realm of the Brazilian Amazon, where some of these discontinuities exhibit features common to tectonic thrusting combined with deep tropical weathering.The evidence of preshearing along the surfaces of such fractures, also associated to products of deep weathering, reduces their geomechanical strength substantially, suggesting values of ultimate phi spanning 12 to 28°. The detection of these descontinuities during initial investigation phases continues to be a major complex task in geological risk evaluations surveys. Trenching associated to some geophysical exploration techniques, although considered to be very basic exploration techniques are still the suggested methods for their forecast and previous determination."

Jan 1, 2015

By Lynne Bowen

"On the da y shift in Number One Mine at Nanaimo on Vancouver Island, on May 3, 1887, William Griffiths, a coal miner with many years experience, fired a shot to advance the face of the crosscut. A flame ran out for a distance of fifteen feet along the roof and then extended up the slope for ten to twelve feet, and although many would have called this a blowing out shot, Griffiths said it was just a feeder. ""A blower"", he said, ""would have caused an explosion."" 1There was no explosion. Griffiths reported gas and the area was cleared for three hours and then work resumed. When the shift changed at 3:00 p.m., the fireman reported all places clear of gas and the ventilation good.2The ventilation in Number One Mine was the best anyone had ever seen. The air in the mine was almost too cold. The current was so strong that it sometimes blew out the flame on the miners' fish oil lamps. It delivered five to six hundred cubic feet of air for every man and animal working in the mine. The law required only one hundred cubic feet 3The miners considered Number One to be relatively safe. The manager was proud of the mine and its up-to-date equipment"". Recently, there had been reports from France and America about the explosiveness of coal dust, but the manager did not think his mine was sufficiently dusty to be dangerous.5 The dust lay thick on the floor of the mine. Sometimes when a shot was fired the dust rose in great clouds. When a miner was shovelling it, the dust would billow up and be carried off by the current of air. The dust was also in the roof and in the stopings, put there intentionally to fill up the spaces and prevent the accumulation of methane gas."

Jan 1, 1992

By E. Trickey

In the mining industry there exists a constant drive for increased safety and productivity and decreased operating costs. This acts as a driver for implementing advanced technology. As more and more mining operations turn to new technologies, an observed bottle-neck for technology advancement has been the limitation of machine vision solutions available. LiDAR has been seen as a possible solution to the machine vision problem. In the past, a few studies on machine vision solutions have been undertaken by various groups involving scanning laser range-finders and millimetre-wave radar. These studies have done little more than highlight the limitations of both technologies in the mining environment. Little work has been done, however, exploring the applicability of LiDAR imaging technology for mining applications. Neptec Technologies Corp. has developed an obscurant-penetrating LiDAR (OPAL) sensor technology which overcomes the limitations faced by traditional LiDAR sensors when operating in a dusty environment, as well as advanced 3D real-time intelligence (3DRi) data processing algorithms that enable the real-time exploitation of 3D imaging data with sensors mounted on moving vehicles. Working with Teck Resources Ltd. and Barrick Gold Corporation, Neptec is adapting the OPAL sensors and 3DRi technology to mining applications. This paper highlights a number of real-time OPAL/3DRi based mining applications demonstrating how this technology overcomes the limitations of traditional LiDAR to provide a real-time machine vision solution that supports mine machine autonomy.

Aug 1, 2013

By Carol Odell

This paper was prepared as a brief for Prospectors and Developers Association of Canada (PDAC) to guide input at a series of round tables carried out by the Federal Government in response to the 38th Standing Committee on Foreign Affairs and International Trade (SCFAIT) report, on ?Mining in Developing Countries and Corporate Social Responsibility?. This document mandate is to provide background information, analysis and recommendations on the practice of Canadian exploration and mining companies abroad. This research was based on 11 case studies of Canadian companies which have experienced conflicts or controversies overseas. All case studies were assembled through an extensive literature review of publicly available documentation and communications with representatives of the mining companies to assist in deepening the insights into the drivers of the conflicts and the needs of Canadian companies in similar situations. The case studies include both exploration and mining operations. Our analysis begins with the identification of general and case specific drivers of conflict/controversy in each case study. Company names are kept confidential and only anonymous results are presented. We make ample use of simple flow charts and schematic diagrams to explain how contextual drivers and aggravators and company drivers and mitigators play varied and interrelated roles in conflicts. The diagrams also illustrate the cumulative analysis of drivers including the linkages among drivers/aggravators/mitigators across different domains (social, governance, NGO/media and company). Finally, we discuss needs of companies and propose recommendations for addressing social responsibility and human rights concerns.

May 1, 2007

By Scott A. Trebilcock

Nautilus Minerals Inc the world?s leader in exploration and development of deep ocean mineral resources is today focused on the recovery of high grade copper-gold from in seafloor massive sulphide mineralization. These mineralized belts, analogous to land based volcanogenic massive sulphides (VMS) deposits are located near tectonic plate boundaries of the Western Pacific and around the world. Nautilus; first development project is Solwara 1 located in benign waters in Papua New Guinea. Since 2006 the company has completed detailed environmental and geological studies at Solwara 1, culminating in a number of world firsts, including the first Environmental Permit for a deep ocean mineral project and the first NI 43-101 compliant seafloor massive sulphide resource statement. Nautilus has relied heavily on proven deepwater technologies from the oil and gas industry in the design of the first mineral extraction system. Pipeline trenching units, workclass ROVs, deepwater production risers and drill cutting removal systems will all be adapted at Solwara 1. Key contractors to the project have all been selected for their deepwater experience, creativity and determination to launch this new industry. Innovation is at the forefront of Nautilus? success to date. This paper gives an overview of the Solwara 1 development and describes the exploration and production technologies adapted for seafloor mineral extraction.

May 1, 2010

By A. G. Slade

"This paper deals with the direct application of rock mechanics in the underground mines at the Sudbury Operations of Falconbridge Nickel Mines Ltd. It covers mining methods, the use of photoelastic models, the fore-casting of rock strains and their elimination, closure methods and other common methods of ground control.INTRODUCTIONROCK MECHANICS IS A STUDY IN ROCK BEHAVIOUR and, although it is being termed a new science, it has been practiced since the industry began. Every person involved with rock excavations, from the mine superintendent to the stope driller, is actually practising rock mechanics. They probably call it by another name -experience, and applications of this knowledge are in evidence throughout the Falconbridge operations. Only in recent years have formal rock mechanics studies been employed to provide technical assistance to the mine operators in their primary objective of producing ore safely."

Jan 1, 1968

By R. B. Nourse, S. F. Gwynn-Jones, S. Nikolic, M. L. Bakker, I. McDougall, H. Joubert

"Tenova Pyromet’s core furnace knowhow and expertise has been built within the ferroalloy and nickel/platinum group metal (PGM) industries with the supply of electric furnaces for a number of nickel/PGM operators, including Eastplats, Lonmin, and Anglo-Platinum in South Africa, Mineraçào Serra Da Fortaleza in Brazil, and Norilsk Nickel in Russia. Tenova Pyromet has also supplied the electrode columns and associated electrode equipment – the heart of the electric furnace technology – for cobalt recovery in furnaces in Zambia and the Democratic Republic of the Congo. The quantity and size of projects undertaken by Tenova Pyromet has provided the opportunity to continuously improve furnace designs and the scope of supply, culminating in the most recent nickel/PGM project currently under construction at Northam Platinum. Through this innovative culture, the Tenova Pyromet Base Metals Initiative was formed in 2015 to develop the Novasmelt™ Furnace; a next generation optimised Top Submerged Lance (TSL) furnace design. The combination of Tenova Pyromet’s advanced Novasmelt™ product with our industry leading electric furnace technology are discussed with reference to applications for nickel and cobalt production. Flowsheet arrangements are compared summarising potential capital savings, operating requirements and achievement of downstream product quality.INTRODUCTION Tenova Pyromet is a leading player in the field of smelting technology development and equipment supply. Tenova Pyromet is the result of the union of three furnace suppliers under the Tenova banner: Techint Technologies (Tagliaferri), Core Furnace Systems Corp (Lectromelt) and Pyromet Technologies. The furnace experience of the combined groups dates back over a century with the earliest Lectromelt going into production in the early 1900s. Throughout the modern era, Tenova Pyromet has developed a reputation for providing dependable innovative smelting technology, high quality equipment and sound project execution to a worldwide client base with customer plants operating in Europe, Southern Africa, North America, South America, Russia, Kazakhstan, the Middle East, South Korea, and India. Tenova Pyromet’s core knowledge and expertise was developed in the South African ferroalloy, base metals, and platinum group metals (PGM) smelting industries. Tenova Pyromet has spent considerable effort on development and has contributed significantly to improve the state of the smelting industry. Tenova Pyromet’s electrode columns have become widely renowned and are now providing significant benefits, especially in increased furnace availability, to many smelting furnace operators. The electrode column is the heart of the furnace as it delivers a controlled amount of electrical energy, at an optimum depth in the burden/bath, to the smelting process. Every furnace is custom designed to the specific operating range and optimal operating point of that furnace and process"

Jan 1, 2017

By I. Thobadi, C. Pawlik, K. Bisaka, S. Mokoena, M. Erwee

The PyEarth™ process developed at Mintek has been demonstrated successfully at pilot scale. Nine tons of ore containing 2.3 mass % of total rare earth oxides (TREO) from a dormant mineralogically complex iron-rich ore deposit, was subjected to a concentrating smelting step in a 200 kW DC open-arc pilot furnace and the rare earths from the resulting slag were extracted via a hydrometallurgical route. This ore deposit is practically not amenable to extraction by conventional methods. The testwork results proved that the PyEarth™ process was able to optimize the extraction of rare earths while minimizing waste through the removal of iron as a saleable iron alloy. Reduction of iron to the alloy in the smelting step was found flexible, efficient, and controllable, while rare earths were left virtually unreduced in the slag phase. The slag chemistry is selected to optimize both the smelting and leaching performances as well as the alloy composition. Leaching of the resulting slag was found possible and most efficient in hydrochloric acid amongst other lixiviants tested.

Jan 1, 2017

By John C. Loretto

"The paper identifies two of the main problems encountered in recent hydrometallurgical plants for the recovery of gold and silver: firstly, the plant recovery is lower than anticipated from the testwork; secondly, the metallurgical accounting figures cannot be reconciled.The principal reasons for the plant recovery being lower than the testwork are discussed, together with solutions that can minimize these problems both during the design stage and during the plant operation after the problems have manifest themselves.The reasons for the difficulties in metallurgical accounting are analyzed by reviewing the various components of the plant figures. Recommended solutions are given for minimizing this problem and the realities of obtaining accurate figures are discussed.IntroductionThe start-up over the last few years of new hydrometallurgical plants for the recovery of gold and silver has brought to the surface again a number of problems. Most of the problems have existed for some time and they manifest themselves mainly in two ways. Firstly, the plant results do not agree with the metallurgical testwork figures; secondly, the metallurgical accounting figures do not balance.Metallurgical TestworkThe plant results not agreeing with testwork figures are mainly due to:a) testwork samples not representative of the eventual plant feed;b) misinterpretation or misunderstanding of testwork ;c) plant losses;d) plant design not allowing testwork results to be achieved;e) operating deficiencies."

Jan 1, 1982

By C. Tissot, R. Palmer

"Due to the low concentrations of gold, direct measurement of gold concentration in ore on belt has not been seriously considered to now. Pre-concentration or sorting strategies have largely consisted of particle sorting based on secondary characteristics such as colour, which can be successful in select cases. CSIRO has produced sample measurement results using gamma activation analysis of ~300 gm samples with accuracies of around 30 ppb at best. With this encouragement, a feasibility study into gold ore measurement on belt for the purpose of sorting pods of gold ore has been undertaken. The study described here included, prototype design options with existing industrial Linacs, extensive Monte Carlo modelling of measurement sensitivity and shielding, further sample measurement, a study of the interaction of target measurement accuracy and sorting efficiency, and a rough estimation of potential economic benefit. The projected model sensitivity of around 0.1-0.15 ppm (1 standard deviation) in 10 seconds for 1 ppm average feed result in good bulk sorting performance and intriguing economic potential.INTRODUCTION Pre-concentration or sorting strategies for gold ores have largely consisted of particle sorting based on secondary characteristics such as colour or density, which can be successful in select cases (Klein, 2010). No method is available to measure gold content for sorting in particles or even in bulk on belt, principally due to the low concentrations of gold present. In fact, in many cases it is difficult to do rapid bulk grade measurements of base metal ores with concentrations many orders of magnitude higher. By a fortunate quirk of nature gold is particularly amenable to gamma activation analysis (GAA). CSIRO has performed extensive work in GAA of samples of crushed ore (Tickner, 2017). This has resulted in the Photon AssayTM technique that is currently being commercialised through the CSIRO spinoff company Chrysos. The technique relies on the recent availability of industrial high intensity X-ray sources such as Linacs which are currently being used in industry for security, medical and sterilisation applications. This development has led to CRC ORE funding a feasibility study to determine whether on-belt measurement of gold concentration is possible at a rate and accuracy sufficient to be useful for bulk sorting, where pods of ore are diverted rather than individual rocks. The study in the first instance is based on Monte Carlo modelling that has successfully predicted the performance of the sample based gold measurements. As well as the measurement feasibility consideration was also given to the likely heterogeneity of gold ores and hence the degree to which useful separation could be achieved. This is then tied to a back of the envelope evaluation of the order of magnitude economics of bulk sorting in an example deposit."

Jan 1, 2017

By Martin P. Raffield

Placer Domes? Campbell Mine, situated in northwestern Ontario, is undergoing an assessment of the efficiency of the operation which is necessitated by the low gold price and a reducing ore reserve grade. A decision has recently been taken to move away from a functional based departmental structure (underground, engineering, geology, etc.) towards a team-based system where crews, engineers, geologists and supervisors are responsible for the planning and operation of a particular area of the mine. The objective is to improve communication and understanding of the goals and achievements and to ensure a forum is available for the generation of ideas. It is intended to increase the accountability and decision-making ability of the teams in an effort to achieve the mines? safety and production targets. This paper presents a critical review of the progress of this organisational change process and its successes and failures at the time of writing.

Oct 1, 2001