Search Documents

By Claude A. Jr. Seger

Introduction This paper presents in detailed form the results of settling tests that were published in a few preliminary notes in the April 1949 issue of the Bulletin (p. 166). Carborel is the trade name for sodium carboxymethyl-cellulose and aluminium carboxymethyl-cellulose produced by the reaction of monochloroacetic acid on the alkali cellulose to form an ether. The water-soluble sodium carboxymethyl-cellulose has been known in Europe for several years as sodium cellulose glycolate and has been marketed under several trade names. These cellulose ethers, however, are relatively new in North America, where the name carboxymethyl-cellulose is often abbreviated to C.M.C., or they are referred to as cellulose gum. The particular grade of Carboxel used in the settling tests in the mill of Chesterville Mines, Limited, is the high-viscosity sodium carboxymethyl- cellulose known as Carboxel H.V. It is a white, fluffy powder and is hygroscopic, although not deliquescent. Carboxel solutions in water are colourless, odourless, and resistant to beat and light. They are stable to alkalies, but are precipitated by acids when the pH is reduced below 4.0, and also by solutions of soluble lead, iron, copper, aluminium, and chromium salts. Solutions of Carboxel exhibit the properties of hydrophilic colloids.

Jan 1, 1949

By A. M. Abdel-Rehim

The present work reports a study of production of thorium concentrate from Egyptian monazite by decomposition of ammonium carbonate solutions containing ammonium thorium and uranyl carbonate complexes. These solutions were obtained from the processing of monazite by alkaline leaching in ball-mill autoclaves, followed by selective separation of thorium and uranium from lanthanides by autoclave leaching of the hydroxide cake obtained with ammonium carbonate - bicarbonate solutions. The separation of thorium and uranium in the form of thorium concentrate from their carbonate complexes was achieved by different methods, including neutralization of solutions at pH = 6.7 by acid, addition of alkali at pH = 11.5, heating of solution at 100°C and processing of carbonate solution with steam under pressure in steel autoclaves. Processing of solutions of thorium and uranyl carbonate complexes in an autoclave with steam causes their decomposition. Complete recovery of thorium 99.8% and 98.4% uranium recovery in thorium concentrate was attained at 120°C and steam pressure 2 atm, within 10 min. Meanwhile, the recovery of lanthanides was low and did not exceed 1.1%. The thorium concentrate produced contains 67.82% Th, 4.6% U and 3.14% REE. All methods achieve complete separation of thorium and uranium from their carbonate solutions, but the first two methods are unfavourable for the industry due to the high cost of reagents and their inability to regenerate the ammonium carbonate. The decomposition of ammonium thorium and uranyl carbonate complexes with steam under pressure is recommended for industrial application for its simplicity and the ability to regenerate the ammonium carbonate.

Jan 1, 2004

By T. Ivankina, T. Lokajícek, H. Kern, T. Svitek

The knowledge of 3D velocity distribution of P- and S-waves in rocks is very important parameter for interpretation and understanding the nature of seismic anisotropy observed in the earth’s crust and upper mantle. A new high-pressure measuring head was designed and constructed to enable ultrasonic sounding of spherical rock samples in 132 independent directions under up to 60 MPa of acting hydrostatic pressure by means of simultaneous longitudinal and transversal sounding. New measuring system enables ultrasonic sounding of spherical rock samples by using a pair of P-wave sensors and two pairs of perpendicularly polarized S-wave sensors (TV and TH) see Fig.1. Shear wave sensors polarization is oriented according to rotation axis of the sample. Special shear wave gel was used to transfer shear waves between the sample and sensors under acting hydrostatic pressure. An isotropic glass sphere was used to check and calibrate the new measuring setup. A spherical sample of a biotite gneiss from the Outokumpu scientific drill hole was used for testing measurement. There is shown that both, P- and S-wave velocities, can be measured simultaneously up to 70 MPa, respectively. We report data of the 3D velocity distribution of P- and Swaves measured for the first time on a sample sphere of biotite gneiss. We rely, in particular, on the directional dependence of compressional and shear wave propagation and their relationship to the crystallographic (CPO) and shape preferred orientation (SPO) of major rock-forming minerals. The 3D seismic measurements revealed a strong foliation-related directional dependence (anisotropy) of P- and Swave velocities. Ultrasonic measurements were compared with 3D velocity calculations based on neutron diffraction measurements of crystallographic preferred orientation (CPO) of major minerals. Comparison of 3-D velocity distribution (P, S1, S2 and S1-S2) determined by two completely different methods ultrasonic sounding and neutron diffraction is presented. Measurements showed that the intrinsic bulk anisotropy is basically caused by the CPO of biotite constituting about 23 vol.% of the rock.

Jan 1, 2015

By R. Q. Honaker

It has been shown that naturally hydrophobic carbonaceous materials such as coal and graphite can be selectively coagulated and separated from hydrophilic impurities without using oily agglomerants, flocculants or electrolytes. The coagulation occurs at C-potentials significantly higher than those predicted by the classical DLVO theory, suggesting that it is driven by the hydrophobic interaction. In the present work, the energy barriers for the coagulation of a hydrophobic coal sample have been calculated using the extended DLVO theory which incorporates the hydrophobic interaction energy in addition to the dispersion and the electrostatic energies. For the coagulation of minerals present in the coal, the classical DLVO theory has been used for the energy barrier calculation. The results of these calculations provide an excellent correlation with the results of a series of Selective Hydrophobic Coagulation (SHC) tests conducted with run-of-mine coal and graphite samples.

Jan 1, 2004

By J. P. Piguet, A. Hosni, J. P. Josien, H. Baroudi, R. Hadadou

"The iron ore mines in the Lorraine region of north-eastern France cover a surface area of approximately 3,900 km2 and involve more than 150 cities. A total extraction method was usually used during exploitation, but this technique was sometimes replaced by the room and abandoned pillar technique when it was necessary to protect surface buildings and infrastructure. Rooms and abandoned pillars were initially designed to ensure long-term mine stability. However, this aim was not always reached and numerous collapses occurred in the Lorraine iron basin, either during production or several years after closure. Several subsidence events were identified during a period of one century; the most recent event occurred in 2012. Two groups of events were identified. The first group represents events characterized by sudden surface movement, and the second group includes event characterized by progressive subsidence.Numerous studies conducted during the last decade helped improve our understanding the origin mechanism of spontaneous or progressive (slow) events. These studies led to identifying long-term potentially unstable underground zones (hazard zones), particularly deep zones located under buildings and infrastructure. The latest are currently monitored by microseismic networks. A similar high requirement level is needed for unstable zones without taking into account the kinetics of the subsidence, which is very important for safety. Thus, GEODERIS initiated this study, primarily to acquire a better understanding of the kinetics of the progressive events group and identify the main parameters that could explain why some pillars zones developed a maximum amplitude subsidence on surface within a few hours or days, while it took several weeks to months for others. In practice, the results of this study will facilitate adapting the requirement level of microseismic monitoring system to the kinetics of pillar collapse.To retrieve the real kinetics for each event, historical and sparse documentation was used. Firstly, archives research was conducted, especially testimonies and newspaper articles published during the events. This work helped to gather useful information that sometimes contained a precise description of subsidence duration. The archives research helped to classify some progressive events according to the subsidence kinetics. Secondly, a diagnostic of geotechnical and geomechanical parameters of historic events was realized, combined with a cross analysis of the data. The analysis took into account dimensions of underground workings (e.g., pillar lengths, widths, heights, introduction of a “pillar shape factor”, and stress amount). An original expression was highlighted to connect the pillar geometry to the stress state. The kinetics expression was calibrated to classify the historic events taken into account according to the kinetics of movements. The kinetic criterion was applied to predict subsidence kinetics for the potential unstable zones currently monitored by a microseismic system."

Jan 1, 2015

By C. Graham

Mechanisation has been a predominant theme of the past 50 years in the mining industry, particularly underground mining. As the level of technology employed has increased, the anticipated productivity gains have not been realised and the differences are not explained by the demand for higher standards of safety and security. Now, mining costs are so high and productivity so low that the resultant return on investment for many Canadian operations has fallen to levels considered unacceptable in a competitive capital market. Simply continuing technological development cannot reverse this trend and its financial implications. The focus on technological development has distracted us from some basic truths. Systems that are more complex are more likely to fail and cost-effective processes depend on the continuity of productive activity and the flow of material. When putting these facts together, it becomes clear that in a system that has fixed external conditions, the single most crucial issue is the effective management of the operational cycle. By its nature, technology focuses our attention on what gets done and how it gets done, while the crucial issue is the increasingly longer periods in the operational cycle when nothing productive is being done. What is required is to match the level of technological complexity to the fixed system conditions, which are virtually unchangeable. This paper looks at the overall system and objectives and attempts to present an appropriate level of technology for the Canadian mining industry, now and in the foreseeable future.

May 1, 2004

By H. C. L. Reemeyer

One of the fundamental trade-offs for copper concentrators is between grinding circuit product size and copper recovery. The capital and operating cost savings and throughput increases for a coarser grind should be evaluated against potential recovery reductions. Other benefits of coarser grinds, such as GHG emissions reductions and favourable effects on tailings and water management should also be considered. This paper assesses the formation of laboratory and pilot test programs, design of process flowsheets, equipment selection, and evaluation methods to determine the most appropriate and economical grind size for a given deposit. The paper will include an evaluation of case studies. INTRODUCTION The majority of the world’s mined copper comes from sulphide deposits, which are mostly processed using crushing, grinding, flotation and dewatering flowsheets to produce copper-bearing concentrates for smelting. Ores must be ground to a sufficiently fine size to achieve an acceptable level of liberation to allow both high recovery of copper and valuable by-product minerals while efficiently rejecting gangue to tailings. Therefore, a key design parameter in process plant design is the grind size of the flotation feed. Copper concentrators use a variety of grind size targets that depend on various factors, including ore mineralogy and the grain sizes of valuable and gangue minerals; the sensitivity of valuable mineral recoveries in the rougher flotation stages to grind size, ore hardness; electricity costs; and mining vs. processing throughput constraints. Typically, copper and by-product recovery increase as grind size is reduced, which can improve revenue, but finer grinds increase power and grinding media operating costs and may have implications for tailings management. This paper explores the trade-offs that should be assessed in determining the optimum grind size, and to answer the question if coarser grinds are worthwhile. METALLURGICAL AND FLOWSHEET FACTORS Recovery-by-size behaviour of sulphide-bearing particles In base metals sulphide flotation, it is typical that flotation recoveries vary by particle size. Metal sulphide particles rendered hydrophobic by collector in intermediate size ranges (e.g. 10 to 100 um) usually show very high recoveries, often approaching 100%. Recovery usually falls away in finer size fractions (<10 um) as fine particles have little inertia and can move around bubbles without colliding and attaching to them. Coarser particles (>100 um) are susceptible to particle-bubble detachment and dropback (Jameson, 2019).

Jan 1, 2019

By J. C. Farge, G. G. Jacox

"The effect of composition and process variables on the properties of Marmet and modified Ni-Hard slugs will be discussed. The effect of shape on the over-all performance of grinding media and its relationship to the end product has been investigated and these results will be reviewed. The cost effectiveness of slugs versus balls has been well documented under various operating conditions and this will be presented in detail. IntroductionThe selection of grinding media is based on the cost-to-wear ratio combined with the consideration that it must stand repeated impacts without breaking. The specific consumption of grinding balls and slugs depend s primarily on their microstructure, which, in turn, is controlled by chemical composition and by the processing condition s to which they are subjected during manufacture.The first part of the paper deals with the optimization of alloy content to produce cast iron slugs with microstructures consisting essentially of marten site and carbide and with hardnesses of 650 B.H.N. and higher. The second part deals with the use of cast iron slugs to replace forged steel balls in milling operations. Tests indicate that the shape of the media has little if any effect on results and that the hardness and microstructure of grinding media will determine its relative performance. Where price is equal under similar milling conditions, the cost effectiveness of cast iron slugs is superior to that of forged steel balls.In order to understand the role of alloying elements in cast irons, it is judicious to consider the microstructural changes which occur during solidification and subsequent cooling, particularly from above the eutectoid temperature. Solidification starts with the formation and growth of dendrites of austenite. As temperature decreases, an eutectic nucleates and grows between the primary austenite dendrites. Immediately after solidification, the structure consists of proeutectic austenite and of the eutectic of primary carbides and austenite. On cooling to room temperature, austenite can be retained or transformed to pearlite, bainite, martensite or mixtures thereof. It is necessary to prevent decomposition of austenite into pearlite by adjusting the alloy content. For best abrasion resistance, the microstructure at room temperature should consist essentially of martensite and carbide. These types of irons are known as ""martensitic irons "". Depending on the carbon content of the austenite and cooling rate, "" as-cast"" martensitic irons will contain different proportions of martensite and retained austenite. The more carbon in solution in the austenite, the lower is the temperature at which the martensitic transfoemation takes place. By the time room temperature is reached ., the transformation is seldom complete, and the end product is generally a mixture of martensite and retained austenite."

Jan 1, 1980

By Sarah Bélair, Denis Beltrami, Valérie Weigel

"Mabounié is a polymetallic deposit in Gabon containing niobium (1.2%), tantalum (0.03%), rare earth elements (REE) (1.4%) and uranium (0.03%) that are mostly carried by Pyrochlore minerals. Classical route for niobium recovery is a pyrometallurgical process that consists in pyrochlore flotation, dephosphorization of the niobium concentrate and aluminothermy to obtain ferro-niobium. Pyrochlore concentrates can also be treated by a hydrometallurgical process with a mixture of sulfuric and hydrofluoric acid leaching followed by solvent extraction to separate niobium and tantalum. However, the first process does not allow recovering REE and the second one is not environmentally friendly because of the use of HF.ERAMET is looking for new opportunities on strategic metals market and has recently developed a hydrometallurgical process for the recovery of all these metals based on a sulfuric acid treatment of the ore. After solubilisation of the valuable elements, niobium / tantalum are precipitated as a concentrate (12% w/w Nb and 0.3% w/w Ta) while REE (2.7 g L-1) and uranium (90 mg L-1) remain in solution. Nearly 90% of REE are recovered from the solution by conventional REE double salt precipitation [NaREE(SO4)2.xH2O) method but some REE still remain in solution as this method does not allow to quantitatively recover medium (Sm, Eu, Gd, Tb, Dy) and heavy (Ho, Er, Tm, Yb, Lu, Y) rare earth elements. From the different process routes studied (solvent extraction, precipitation, ionic exchange etc.), an innovative method has been developed and patented to recover REE residual concentration in solution. This is based on an aluminum removal step followed by precipitation of REE as REE phosphate concentrate (REEPO4) by phosphate addition into solution. The phosphate concentrate is then purified according to the conventional monazite treatment, i.e. caustic conversion and REE solubilisation in acidic media."

Jan 1, 2016

By Golaleh Riahi

An original method is used to obtain stable nanoparticles of gold-based mono- and bimetallic systems supported on an acidic zeolite. This approach has been applied to PtHY (1wt% Pt) and to bimetallic Pt-AuHY containing 1% of platinum to which is added the amount of gold required to give Au/Pt molar ratios of 20,40,60 and 80%. Metal clusters of Au or Pt-AuHY are formed inside the supercages of the zeolite framework by the thermal reduction of cations by the ligands (en = H2N-CH2-CH2-NH2) under inert gas flow at a temperature depending on the metal. The use of acidic zeolites favours the dispersion of the metal and the thermal stability of the particles. This stability is explained by chemical anchoring of metal clusters by the Brønsted sites of the support. Several techniques have proved that for a molar ratio of 20% metal particles of Pt-AuHY are bimetallic. The segregation of Pt and Au starts for molar ratio =?40%. The catalysts tested on the methylcyclopentane hydroconversion reaction reveal that the addition of gold to platinum leads to an increase in the activity and an improvement in the selectivity for isomerization of the skeleton (cyclohexane and benzene) to the detriment of hydrogenolysis. Similar results were obtained for the dodecane isomerisation to isododecane. These catalysts were also tested in CO, propene and propane oxidation. The activity of fresh catalysts is rather low. It increases after their pretreatment in oxygen or hydrogen atmosphere. In propene oxidation in the reaction mixture O2 ? H2, beside total oxidation of propene to CO2, also propene hydrogenation was observed, particularly at low temperatures. The presence of Au enhances the hydrogenation properties: high selectivities (> 90%) to propane and high propane yields on PtAu HY are observed up to ~150oC, whereas for Pt HY catalyst the selectivity and yield to C3H8 decreases rapidly with the temperature beginning from ~100oC.

Oct 1, 2003

By T. V. Nethery

Introduction A brief account of the East Malartic fire is essential if this paper is to serve the purpose implied by its title. The fire originated in the timbers of No. 4 shaft at the 10th, or 1,570-foot, level; this was the top or collar of the underground sinking operations. At the time, sinking was in progress and the shaft bottom was 242 feet below the 12th station horizon, or 618 feet &apos;below the l0th level. Above the l0th level, the shaft was not in use as the surface plant was not yet completed. The shaft crews descended from surface in No. 3 vertical shaft to the l0th level, where they transferred to No. 4 shaft, a distance of 1,450 feet. Of the sixteen shaftmen mucking at the shaft bottom, four were able to reach safety. One shaftman was overcome by fumes midway between the two shafts on the l0th level, while attempting his escape. The remaining eleven men climbed as far as the 11th station and there succumbed to carbon monoxide. No. 4 shaft, inclined at 61 degrees, bad been raised and timbered from the 10th level to surface; this bad been followed by sinking operations below the l0th. Two air hoists had been set up in the footwall of the shaft, 110 feet above the 10th level, and directly behind compartments No. 2 and No. 4. The waste from the shaft bottom was hoisted in 28-cubicfoot buckets on mono rails and dumped over standard shaft sinking doors into waste chutes built into No. 1 and No. 3 compartments. The five-compartment shaft, 7 ft. 8 in. by 34 ft. 6 in. overall size, was heavily timbered. In addition to the standard shaft timbers of 8 in. by 8 in. and 8 in. by 10 in. B.C. fir, the hanging-wall and ends of the shaft were laced with 4-inch spruce lagging. This represented approximately 300 board feet of timber in placee for every foot of shaft. The cause of the fire bas never been determined, despite every effort to do so. The inquest held for those who lost their lives in the fire was an extremely thorough one, but only the location of the origin, and not the cause, was established.

Jan 1, 1950

By Georgia J. Lysay

Kemess South Mine ended operations in March 2011. Final reclamation works began during operations in 2008 in anticipation of closure. The focus of reclamation during mine operations was on the inactive areas of the tailings dam, waste rock dumps, and expended borrow areas. The general reclamation strategy for the Kemess Mine site marries long-term erosion control with successional reclamation principles. For disturbed areas, this requires application of growth media, proper preparation of surfaces, and introduction of native pioneer plant species to initiate successional processes of recovery. Tailings are retained behind an earthfill dam of approximately 140 m in height, with a crest length in excess of 1 km. Reclamation activities at the dam have included placement of growth media, specialized surface preparation and construction of diversion ditches. The final closure spillway is currently being constructed, with completion scheduled for summer 2011. The two main waste rock dumps contain segregated non-acid generating (NAG) waste rock and potentially acid generating (PAG) waste rock. Resloping of the NAG dump for long-term stability commenced in 2009, followed by placement of growth media and ground preparation. The PAG waste rock will be fully relocated into the expended open pit for final, permanent subaqueous disposal.

May 1, 2011

By A. Gronningsater

Introduction As is well known, the fight between the blast furnace and the reverberatory furnace in copper smelting during the second decade of the century ended with a victory for the latter, a result which must largely be attributed to the introduction of flotation methods. To my knowledge, no new blast furnace has been blown-in at any American copper smelter since the War. As the metallurgy of nickel, up to and including matte smelting, is generally considered a close parallel to that of copper, the introduction of reverberatory smelting in the big new smelter of the International Nickel Company at Copper Cliff, built in 1928-30, seemed a logical adherence to a well established trend. In view of these facts, considerable comment was made when Falconbridge Nickel Mines decided to retain the blast furnace in their smelter built about the same time, in 1929. A presentation of the reasons governing this choice should therefore be of interest. The basic principles underlying the Falconbridge practice, and the considerations guiding the successive steps in the operations, will be discussed in the following. To understand the problems involved, the character and mode of occurrence of Sudbury ore must be kept in mind. Large amounts of disseminated ore are generally present. Although the gangue usually runs only about 50 per cent Si02, the ore hoisted as a rule contains more silica than needed in the smelting operation; until recently this excess was removed entirely by hand picking (in later years supplemented by magnetic sorting methods), a difficult and not very satisfactory method, in which &apos;the border line between ore and waste is entirely arbitrary, and therefore too much depends on the judgment of the picker.

Jan 1, 1934

By W. C. Zhu, C. H. Wei, L. L. Niu

With an increase of mining depth, a series of mining-induced hazards such as rockburst, coal and gas outburst, roof collapse, and water burst are getting more serious and more frequent. The intrinsic mechanism responsible for the occurrence of mining-induced hazards is the damage and unstable failure of rockmass or coal seam. The most distinct difference between deep and shallow levels is the so-called three ‘high’ (H3) conditions, i.e. high geo-stress, high fluid pressure and high geo-temperature. Therefore, the response of rock or coal to the deep mining operation is a phenomenon involving thermal (T), hydraulic (H), and mechanical (M) processes. Most importantly, mining excavation may vary the rock stress condition greatly, which may be a key factor to trigger the mining-induced hazards such as rockburst. In this regard, it is of great significance to clarify the damage and failure mechanism of rock and coal under coupled THM conditions, in order to clarify the rock failure mechanism responsible for the occurrence of mining-induced hazards. Thereafter, the mining-induced hazards cannot be predicted with confidence by considering each process independently. Of course, the requirement to include coupling of these processes depends on the specifics of the mining-induced hazards under consideration. For example, the water inrush is considered as a coupled hydro-mechanical (HM) process, in which the unstable failure of rockmass occurs under the combined contribution of geo-stress and water pressure. As for the coal mining at depth, in addition to high geo-stress and gas pressure in coal seam, the high geo-thermal condition that may greatly change the adsorption / desorption of gas and gas flow should be taken into account. Firstly, a general-purpose mathematical model for rock damage and failure process under coupled THM conditions is formulated based on damage mechanics principle, and it is solved by finite element method (FEM). In this model, the deformation and damage of rock, fluid flow and thermal transfer in rock would interact with each other, one process affects and initiation and progress of another. Then, the model is used to predict the mining-induced water outburst, where it is simulated as coupled hydro-mechanical (HM) problems. Based on the numerical simulation, the dimension of water-proof pillar is designed. Finally, the gas drainage from deep coal seam is numerically evaluated, where the coupled coal-gas interaction considering the effect of gas adsorption/desorption, gas flow in coal seam and geo-stress and geotemperature, is comprehensively taken into account. The proposed model could be used for clarifying the mechanism of mining-induced hazards in deep-level mining.

Jan 1, 2015

By B. Holaday, H. McLaughlin

Orano Canada Inc. (Orano) operates the McClean Lake mill, located in the Athabasca Basin region of northern Saskatchewan. It processes high concentration uranium ore, delivered in slurry form from the Cameco Corporation operated Cigar Lake mine. After the ore slurry is leached at the McClean Lake mill, the leach residue solids are washed in a process known as counter-current decantation (CCD). This process uses six thickeners to facilitate counter-current washing of solids with diluted acid, flocculation and settling, as well as pumping the washed leach residue to the tailings neutralization circuit (TN), and the uranium laden aqueous to the solvent extraction circuit (SX). Challenges in settling the slurry in CCD started in early 2017. This is largely due to the variation in fines content of the slurry (D80≤75μm), and clay content. There are several changes that have allowed the mill to adapt to the evolving challenges of settling leached Cigar Lake leach residue. Flocculant selection and mixing, temperature effects, bed level management philosophy, and centre-well feed density are key parameters that have been explored as part of adapting to changes in Cigar Lake ore quality.

Jan 1, 2020

By G. K. Lee, E. R. Mitchell

Designers of combustion processes may select aerodynamic conditions which produce only superfine fly ash. Although it is not usually anticipated that this will create a problem, such as has been found to agglomerate in high-velocity gas streams, to plug mechanical dust separators in a short time, and to contribute to atmospheric pollution. The problem is a fundamental one, and may be approached in several ways. The authors, in the course of their combustion research program, had occasion to examine the agglomeration of ash, ranging from sub-micron to 17 microns in size, produced in a (coal and oil) dual-fuel-fired steam generator. Several theories, supported by extensive laboratory studies, have provided some understanding of a probable mechanism of agglomeration. As a result, certain precautions are suggested in the design and selection of combustion processes and equipment.

Jan 1, 1962

By I. I. Betcherman

INTRODUCTION A DISTILLATION process offers one of the most effective methods of refining metals. Its use is particularly attractive in the case of reactive metals which are not readily treated by pyrometallurgical or electrolytic methods. The 1ow vapour pressure of most metals severely restricts the applicability of the disti1lation process and only one or two metals may be effectively treated under atmospheric pressure at a reasonable temperature. If operations are carried out under reduced pressure several additional metals may be effectively distilled. Table I shows the vapour pressure of a number of metals together with a value of the free energy of formation of their ?oxides. Zinc and cadmium head the list and for many years? they have .been effectively refined by distillation. Sodium, magnesium, and calcium follow in descending order, and they may be distilled readily in vacuo and with difficulty at atmospheric pressure. Sodium, which is not of great metallurgical interest, is not considered. Magnesium has recently been produced in considerable tonnages by distillation methods ( 3). This paper describes the vacuum distillation of magnesium and calcium, their separation from each other, and their separation from less volatile impurities.

Jan 1, 1951

By Fabio Terzi

In this investigation some preliminary results are reported about the electrochemical oxidation of CO using goldbased encapsulated nanoparticles grafted on conducting substrate. The investigation has been planned in four steps: 1. production of Au(111) substrate and modification with self assembled monolayers; 2. synthesis and embedding of nanoparticles; 3. grafting of encapsulated nanoparticles on electrode substrates; 4. investigation of CO electroxidation on the modified electrode. The systems were characterized by means of various techniques (spectroscopic, microscopic, and electrochemical methods), obtaining information about SAM&apos;s structure and morphology, size and composition of nanoparticles and electrochemical behavior of modified electrodes.

Oct 1, 2003

By W. K. Chan, R. Lahaie

"The Suncor Oil Sands Mine located north of Fort McMurray, Alberta, produces about 80000 m&apos; per day of tailings waste which must be disposed of economically in an environmentally acceptable manner. To date, this has been accomplished by impounding the high water content tailings wastes behind large dykes, many of which approach 100 m in height .The dykes are constructed using suitable overburden material stripped prior to the mining of the oil sands feed and/ or the coarse sandy fraction of the tailings waste itself. Although the above is common practice at many mining operations, the large volumes handled and the resultant costs require designs to be meticulously fine-tuned toward the optimum. As a result, considerable effort is expended on planning, designing and construction, and performance monitoring. The lack of precedent experience (Suncor pioneered oil sands mining), coupled with the realities of long, harsh winters and a variety of troublesome site conditions and construction materials, has led to some very unique dyke construction.This paper overviews current tailings disposal plans as welt as some of the key issues related to the design, construction and performance of these large dykes."

Jan 1, 1988

By A. Torkian

Process water from production of concentrates in Meydook copper sulfide mine is transferred to the 8.3 million m3 tailings dam and a water retention pond after initial thickening. Elevated concentrations of heavy metals, sulfate, and TDS and decrease in pH as well as seepage into the aquifers have been the concern of the regulatory agencies since the start of activities. In this paper the results of a 6-month monitoring program from 4 wells are presented. The wells were located approximately 1.5 km from downstream of tailing dam (0.4 km from water retention pond) as well as upstream background well (2.28 km from water retention pond and 1.27 km from tailings dam). The objective was to study possible effect of accumulated tailings on the groundwater resources. Water levels in sampled wells were on average between 20 and 40 m. Results showed high levels of lead (5 ppb), copper (0.17-0.46 ppm) and selenium (73.1- 29.1 ppb). High levels of selenium and lead were partly due to natural geological settings of the area with high levels present in unaffected soils in the vicinity including water wells of villages upstream of mining operations. High copper levels were attributed to both mining operations as well as deposition from particulate air deposition onto the soil and transport to ground water by rain.

Aug 1, 2013