Search Documents

By A. Taylor, E. Thorn Corthay, J. Farrell, L. A. Westfall, S. Borchardt

Mining and metallurgical industries need to minimize their greenhouse gas (GHG) emissions; Hatch specializes in conducting mining and metallurgical energy management assessments and optimizing productivity. Projects executed have demonstrated that there is a wealth of energy management, waste reduction, and process efficiency improvements that require no or low capital investment. Typical energy cost savings are on the order of 5% to 12%, with similar reductions in GHG emissions. Hatch generates Marginal Abatement Cost Curves to optimize the implementation pathway, maximizing carbon abatement and minimizing cost. The findings of a practical case study from Cameco are presented.

Jan 1, 2010

By F. C. Lendrum

Introduction The property of Normetal Mining Corporation is in Desmeloizes township, Quebec, twelve miles north of Dupuy on the main line of the Canadian National railway from Quebec city co Cochrane, Ontario. The ore bodies occur within a band of highly sheared and sericitized agglomerate which strikes N.60°W. and clips 82° north. Along a zone 1,000 feet or more in length and of variable width, the agglomerate has been replaced by copper, zinc, and iron sulphides, with copper usually predominant on the hanging-wall side and pyrite replaced in part by sphalerite on the footwall. A northsouth diabase dyke cuts through the ore zone near its east end. The Normetal mill produces a copper concentrate and a zinc concentrate which are shipped, respectively, to Noranda, Que., and Newcastle, Penn., U.S.A., for further treatment. The present paper deals with the milling of ore from what is known as No. 3 orebody. This is a lenticular body of high-zinc ore lying co the east of the diabase dyke, along the line of strike of the main ore zone, which extends westward from the dyke. On its northern side, No. 3 orebody is in contact along most of its length with a narrow band of copper ore which is highly oxidized.

Jan 1, 1948

By F. Ajersch, A. R. Hekmat

Apparent viscosities of hypo-eutectic (Al-7% Al) and hyper-eutectic (Al-35% Si) binary alloys were measured in the semi-solid state using a Couette type viscometer at variable shear rates. Analysis of the microstructural evolution demonstrates the differences in the rate and degree of attrition of the primary phase particles which are characteristic of the thixotropic nature of the semi-solid alloy. It was observed that the Si primary phase in the hyper-eutectic alloy is much more difficult to fragment than the dendritic a-Al phase in the hypo-eutectic alloy. For the case of the a-Al, the dendritic structure is broken down by attrition and fracture of the dendrite arms whereas the fracture of the Si hexagonal crystals in the hypereutectic alloy occurs along the {100} and {110} cleavage planes. Results are presented for fixed solid fractions of the primary phase at isotherm condition for each type of alloy.

Jan 1, 2006

By Christopher Andreae

Years before iron and steel works were established at Sydney, several thriving although short-lived iron works operated in Nova Scotia. These furnaces reflected the general nineteenth-century North American experience with iron works. At the beginning of the century, small furnaces struggled to supply local needs. Charcoal was the principal fuel and water powered most furnace equipment. By the end of the century, a few huge primary iron and steel works dominated production for Nova Scotia and the rest of Canada. Two sites achieved prominence in the nineteenthcentury Nova Scotia iron industry: Londonderry and Ferrona (Fig. 1). Londonderry, the larger and longerlasting of the two sites, is today a small village on the south flank of the Cobequid Mountains, about 30 km west of Truro. Prior to the establishment of an iron works in 1849, no community existed. At the peak of operation in the 1880s, however, over 2600 people were located there. The second site, Ferrona, today is a mere crossroads on the map, about 10 km south of New Glasgow. Following the construction of a blast furnace there in 1892, a small village grew up around the furnace. But once the furnace was blown out in 1904, the population gradually drifted away.

Jan 1, 1999

The AG/SAG circuit discharge P80 is now increasingly referred to as the ?Transfer Size? or T80 for short. From the literature it is apparent that in circuit design some approaches to the sizing of AG/SAG mills as well as the ball mills that they feed use this parameter. This paper reviews whether the use of the T80 is appropriate in this context. In the course of the review examples of AG/SAG discharge size distributions measured from range of operating circuits are used to illustrate the arguments made.

Jan 1, 2012

By P. Fossi

This report describes a pilot-scale study of a hydrometallurgical process to treat high-grade nickel matte or a nickel-cobalt sulphide precipitate to produce high-purity electrolytic nickel. The first step of the process is the oxidative leaching of the nickel-bearing material by nitric acid; the nitrous gases generated during leaching are reconverted to nitric acid. The crude nickel sulphate nitrate solution is purified and is then subjected to a denitrification step. Nitrate separation is effected either by the crystallization of nickel sulphate or by precipitation of basic nickel carbonate. The electrolyte is prepared from the nitrate-free material and nickel is then recovered by electrolysis of the sulphate solution using insoluble anodes. Some technical and economic problems encountered with this processing route are discussed and the method is compared to the "all-chloride" process developed by Société Le Nickel.

Jan 1, 1977

By John C. Taylor

A resource document, prepared for the Royal Commission on the Health and Safety of Workers in Mines, which outlines aspects of occupational health and safety in the Canadian metallurgical industry has been expanded to provide examples of some practical solutions. General process descriptions are provided in conjunction with some of the major potential hazards associated with each step. Emissions to the working environment, particularly around converters, are discussed. Newer metallurgical processes, the role of automation and other advances in the metallurgical industry are described with respect to their impact on the work place. The role of staff and unit employees in providing safe working conditions in the complex metallurgical plant of today is outlined and the need for close cooperation within the human sector emphasized. The technology is available and is being applied to integrate the complex process requirements with realistic regulations to control emissions and provide a safe, healthy environment in metallurgical plants.

Jan 1, 1978

By Bruce Macdonald

Operational monitoring of slope stability can be achieved by space based InSAR monitoring platforms. Natural and man-made rock slopes are monitored using a novel stack-based InSAR method that exploits both persistent point scatterers (PS) as well as coherent distributed scatterers (DS) such as areas of pavement and sparsely vegetated surfaces. The new method, Homogenous Distributed Scatterer (HDS)-InSAR identifies InSAR targets by using adaptive multilooking of statistically homogenous pixel neighbourhoods combined with thresholding the differential temporal coherence of each target candidate with respect to its surroundings. HDS-InSAR preserves PS and therefore forms a direct generalization to our proven DualScale-PSI method. The density of HDS exceeds that of PS by more than an order of magnitude often providing essentially continuous coverage over urban and industrial landscapes featuring a mix of infrastructure with mostly bare soils or rock surfaces. The improved coverage enables better definition of surface motion and underlying geology, which will lead to superior interpretation of the geophysical mechanisms causing the surface deformation, e.g. through improved integration with 3D deformation modeling. We illustrate the performance of our new HDS-InSAR method compared to DualScale-PSI using displacement results from Vancouver, Canada; Bingham mine, USA; and the Palabora mine, South Africa.

Jun 1, 2012

By M. S. Badollet

INTRODUCTION THE DEMAND for general knowledge on asbestos fibres has increased considerably in recent years. A few publications have printed data showing some of the physical and chemical prupertie3 of asbestos, but in many cases this information is difficult to find and is seldom available when needed. During the past ten years, Johns-Manville have received many inquiries on the physical and chemical properties of asbestos fibres. Fortunately, we had some of the information in our files, and we willingly supplied the data. To help relieve this need, we have tried to present briefly in this paper some of the interesting and out-standing properties of asbestos. This information was obtained over a period of years by search of the literature and by experimental investigations. PROPERTIES OF ASBESTOS FIBRES Table I (1, 2) presents, in convenient form for easy comparison, data on the principal properties of the several varieties of commercial 'asbestos' -actinolite, amosite, anthophyllite, chrysotile, crocidolite, and tremolite. Under each variety of fibre is a brief statement describing the properties in terms of structure, mineral association, origin, etc. Some of the more important data in Table I are expanded and presented in Table II (3). SOLUBILITY OF ASBESTOS A report ( 4, 5) discussing the effects of acids and caustic on asbestos fibres was published in Germany in 1927.

Jan 1, 1951

By S. H. Logan

Mr. B. Neilly: A week or so ago the Secretary was good enough to forward me an advance copy of this paper by Mr. Logan and it was suggested that I comment on it at this meeting. At that time I was not very certain that I would be here, so I committed my thoughts to paper. As a matter of courtesy to Mr. Logan, I sent him a copy of my proposed remarks and I would like to give you just what I sent to him. Appreciating fully Mr. Logan's ability and many sources of information, one naturally hesitates to question anything seriously set forth as his considered opinion. Neither does one of my political stripe like to accuse him of being too 'conservative.? However, in places his paper reminds me of another general manager of a Canadian bank. While I was still Secretary of the Ontario Mining Association, this general manager wrote asking for our forecast on the current year's mineral production, stating that he proposed to refer to such production figures in his annual address to his shareholders. The request was considered very complimentary to the Ontario Mining Association and, in my opinion, justified a great deal of serious study and effort. Finally, the estimate was prepared and forwarded, showing a modest increase over the previous year's total. Picture our surprise and chagrin on reading his address to find that he predicted not an increase but, if you please, a decline of over $10,000,000. Before I cooled off I wrote asking the basis of such a prediction and got a reply to the effect that men in his position had to be ultra conservative in picturing the future.

Jan 1, 1931

By H. Huang, H. M. Chen, W. B. Xie

Cu-0.8Cr-0.1Zr alloy were prepared by atmospheric melting. the microstructure and properties of the CuCrZr alloy after first cold rolled, solid solution, second cold rolled and aging treatment were analyzed by using optical microscope, electrical conductivity analysis and Vickers hardness tester. The results show that with the increase of the first cold rolled deformation, the grain breakage becomes more serious, and the cold hardening becomes more obvious and the hardness increases. The conductivity and peak hardness of the first cold rolled (reduction of 30% and 60%) alloys after solution, secondary cold rolled and aging treatment reaches 81 %IACS and 187 HV, respectively. However, the conductivity in the CuCrZr alloy with a higher rolling degree (reduction of 90%) after solution, secondary cold rolling and aging treatment is significantly higher, and the conductivity and peak hardness is 85.8 %IACS and 178 HV, respectively. INTRODUCTION CuCrZr alloy has been widely used in domestic industry for its excellent comprehensive properties such as high strength and high conductivity, especially in the contact wire and lead frame of high-speed railway (Sun, Tao, & Lu, 2015; Mishnev, Shakhova, Belyakov, & Kaibyshev, 2015; Zhang et al., 2016; Fu et al., 2017). In recent years, a lot of research has been done on how to improve the strength and conductivity of CuCrZr alloy. However, the high strength and high conductivity of copper alloys are contradictory characteristics. On the one hand, the addition of alloying elements is conducive to solution strengthening and aging strengthening; on the other hand, too much alloying elements in copper alloys cause defects in the lattice of copper matrix, resulting in a serious decline in the conductivity of copper alloys (Martienssen & Walirmont, 2005). How to obtain high strength and high conductivity at the same time is the main problem. At present, the main research methods are adding microalloying elements, thermomechanical treatment and severe plastic deformation to study the electrical conductivity and mechanical properties of CuCrZr alloys. For example, Xie et al. (2011) added trace Ag to the Cu-0.26 wt%Cr-0.08 wt%Zr alloy, and the size of precipitated phase Cr and Cu4Zr became smaller and the mechanical properties of the alloy were improved. Su, Dong, Liu, Li, & Kang (2004) found that the addition of trace Mg in CuCrZr alloy inhibits the growth of precipitated phase and reduces the internal stress around the precipitated phase. At the same time, the size of precipitated phase becomes smaller and the peak aging strength of the alloy is improved. Pang et al. (2013) found that adding trace Ni and Si to the CuCrZr alloy could improve the peak hardness, softening resistance and precipitation morphology of the alloy. Experiments shows that the grain size was significantly refined by equal channel angular extrusion combined with aging treatment, while the strength of the alloy was increased, and the electrical conductivity of the alloy did not decrease (Vinogradov, Patlan, Suzuki, Kitagawa, & Kopylov, 2002; Saray, 2016); Kermajani, Raygan, Hanayi, & Ghaffari (2013) showed that the strength of CuCrZr alloy can be improved by rolling at 500 °C. After 150 minutes of aging treatment, the strength and conductivity of the material increased to 431 MPa and 81 %IACS, respectively. Takata, Ohtake, Kita, Kitagawa, and Tsuji (2009) noted that the strain hardening, uniform elongation and tensile strength of the nano-precipitates produced by the mechanical heat treatment process can be notable enhanced. The mechanical and electrical properties of CuCrZr alloy can be improved by combining large plastic deformation with aging treatment in the test process (Gao, Huttunen-Saarivirta, Tiainen, & Hemmila, 2003; Huang et al., 2003; Xia et al., 2012; Zel’dovich et al., 2014).

Jan 1, 2019

By Tsuyoshi Adachi

Photovoltaic (PV) system is especially taken notice as one of important renewable energy resources, because PV has potential to provide a certain amount of energy supply as well as without greenhouse gases emission. Considering recent rapid increasing demand for PV system, more expansion of PV system is expected in the future. However, some precious metals and minor metals such as silver, indium and others are used as component materials of solar cell in PV system. Even if energy supply would become renewable, strict limitation of these metals still remain because amount of natural resources and recycling of metals has restrictions intrinsically. The aim of this study is to reveal the possibility of materials supply restrictions for Photovoltaic system quantitatively and to propose several measurements to assess supply risks for materials. Especially, silver supply potential which is used as wire line in PV system as well as PV demand forecast to estimate material use in the future are focused on. We divide underlying supply risk into 5 measurements and analyze them by time series, i.e. price volatility, resource potential, recycling ratio, production type and supply concentration are investigated. Comparing these factors of silver with other metals, the potential of silver supply for PV is presented. In addition to it, we propose another method to quantify country risk applied an insurance pricing model in finance pricing theory and combine it with the supply concentration measurement. As a result, supply risk of silver will increase gradually in the near future because of its resource constraints and supply-demand balances although silver market is sufficiency competitive one. From the country risk analysis, Peru is not only a significant supply country but also has the highest country risk. Some higher risk countries will increase the level of supply risk even if the concentration ratio of supply indicates moderate level.

Aug 1, 2013

By W. E. Kuhn

Introduction The work, of which some of the results are described in this paper, was started with the object of investigating the properties of certain binary alloys of titanium made from powders. Our main interest was in the possible use of such alloys in gas turbines. We were attracted to titanium, as have been others, by its high melting point (I,724° ± 11°C.), its low density (4.54), and the likelihood that, if a relatively wide use could be found for the metal, it might become available in commercial quantities at a fairly reasonable price. The readiness with which the metal reacts with hydrogen, oxygen, and nitrogen was recognized from the very beginning. At the same time there seemed a good chance that alloys could be produced which, because of the formation of protective films, would resist the attack of these and other corrosive agents. No specifications were drafted to cover the 'quality' of the titanium hydride powder which was used in our work and which was, to judge by the results of a few preliminary experiments, the most useful source of titanium then (1944) available in sufficient amount for our purpose. During the course of our work, the need for such specifications became very clear (see Sections 9 to 12 of this pa per). Even today, lack of knowledge regarding the effects on titanium of impurities, some of which may later be looked upon as essential elements in commercial alloys of titanium, and difficulties in manufacture, make the preparation of specifications for commercial titanium and titanium compounds a doubtful procedure. The papers presented at the 1948 Symposium on Titanium, sponsored by the U.S. Office of Naval Research lend colour to this view. At the time our work was commenced, one had to depend upon the manufacturer to supply what he considered to be his 'best' material. It may be some time before we can ask for more than this, the question as to what is his 'best' being left to the manufacturer to decide. However, in this connection the results of our study may be of some value and on that account we are constrained to publish them.

Jan 1, 1950

By Victor Azbe

Introduction Lime enters our daily life in many ways. Our building, chemical, agricultural, sanitary, and industrial endeavours depend on it to such a great extent that it could probably be called the most important inorganic chemical, and the extent to which it is used might be considered an index of industrial development. Industrial limes vary greatly in quality, due to internal structure and other characteristics. They may be good or bad, sensitive or slow to react. While improper manufacture may not greatly alter the appearance of the lime, it may affect its properties considerably and thus its suitability in the many processes in which lime is used. In some of the processes, one kind of lime is wanted, in others another. While the nature of the stone from which it is made has much to do with whether a lime is suitable or not, its burning and hydration are the crux of the matter. Up to not so many years ago, the knowledge of lime burning was rather imperfect and it is only relatively recently that its manufacture is approaching the state of a higher industrial art. This slow development was in part due to lime manufacture being scattered among many small concerns who, independently, either lacked the inclination or could not afford to strive for a higher technical development.

Jan 1, 1946

By Wm. Snow, J. R. Wallace, E. P. Duchemin

"GeneralA NOT INCONSIDERABLE proportion of the Canadian economy is dependent on the coal mining industry. This is particularly true of the eastern portion of Canada and especially so of the ( authors') province of Nova Scotia. Much has been said about the trying economic straits of the coal industry in Nova Scotia ( 1), faced, as it is, with difficult mining problems, with considerable distance from large markets, and with •competition from other (and usually foreign) fuels. It is of particular interest, at this time, therefore, to discuss one of the larger outlets for coal -that of the production of metallurgical coke.Scope of PaperWhile the title of this paper indicates that it deals with Metallurgical Coke in Canada, the authors beg leave to treat the Canadian industry very briefly and to deal specifically with coal, •coke, and smelting problems with which they are familiar, namely, the operation of the Dominion Steel and Coal Corporation in the Sydney, N.S., area. No mention is made of metallurgical coke for use in the •many foundries in Canada or in the non-ferrons metallurgical industries.Coal and Coke StatisticsA few statistics of the total output of .Canadian coal, production of metallurgical coke, and similar figures for the Dosco holdings (Sydney area only) are shown in Table I."

Jan 1, 1955

By M. B. Kime

"A set of experimental batch leaching tests studied the effect of pH, time, temperature, and stirring speed on the relative Cu, Co, Ni, and Fe leaching yields of an oxidized copper-cobalt ore sample in an aqueous hydrochloric acid solution. The results were statistically analyzed and modelled using the structural equation modelling method. Models showed that Cu, Co, and Ni leaching yields were strong functions of the leaching time and leaching temperature, whereas the Fe leaching yield depended on the leaching temperature, stirring speed, and pH. Under optimum leaching conditions yields were 99.8% Cu, 82.4% Co, 91.3% Ni, and 30.6% Fe.RÉSUMÉ Une série d’essais expérimentaux de lixiviation en bâchée ont été menés pour étudier l’effet du pH, de la durée d’attaque, de la température et de la vitesse de brassage sur les rendements relatifs de lixiviation du cuivre (Cu), du cobalt (Co), du nickel (Ni) et du fer (Fe) d’un échantillon de minerai de cuivre-cobalt oxydé dans une solution aqueuse d’acide chlorhydrique. Les résultats ont été analysés et modélisés statistiquement à l’aide de la méthode de modélisation par équation structurelle (SEM, de l’anglais structural equation modelling). Les modèles ont montré que les rendements de lixiviation du Cu, du Co et du Ni dépendaient énormément de la durée d’attaque et de la température de la lixiviation ; le rendement de lixiviation du Fe, quant à lui, dépendait de la température de la lixiviation, de la vitesse de brassage et du pH. Dans des conditions optimales de lixiviation, les rendements étaient de 99,8 % pour le Cu, de 82,4 % pour le Co, de 91,3 % pour le Ni et de 30,6 % pour le Fe. INTRODUCTIONThe Katanga province in the Democratic Republic of Congo hosts the northwestern part of the Central African Copperbelt. This region abounds with large, rich deposits of sulfide and oxidized copper-cobalt ores. In general, the main valuable minerals present are malachite (CuCO3Cu(OH)2) and heterogenite (CoO(OH)). Common impurities found in heterogenite are Cu, Ni, Si, Al, Mn, and Fe. The substitution of Co by other cations (e.g., Cu, Ni, and Fe) has an influence on the crystallinity of heterogenite (Deliens, 1974). In general, well-crystallized varieties of heterogenite have lower impurity contents, whereas amorphous heterogenite types usually contain more impurities (Thys et al., 2009). Further, in heterogenite, Co can occur in the 2+ and 3+ oxidation states. The gangue generally consists of quartz (SiO2), talc (Mg3Si4O10(OH)2), kaolinite (SiO2·Al2O3·2H2O), limonite (Fe2O3·3H2O), and goethite (FeO(OH)). Oxidized copper-cobalt ores are often treated by hydrometallurgical methods, whereas sulfide ores are often treated by flotation or pyrometallurgy, depending on their grades. Hydrometallurgical methods typically entail selectively dissolving the metals of interest (Cu, Co, and Ni) in aqueous solutions (leaching), transferring the dissolved metals to an organic solution, and retransferring these to a second aqueous solution (solvent extraction). Copper and nickel are readily dissolved in an acidic aqueous media. In contrast, cobalt is difficult to dissolve, especially if it is present in the third oxidation state; however, this species becomes soluble after it is reduced to Co2+ (Mwema, Mpoyo, & Kafumbila, 2002; Kime & Makgoale, 2016)."

Jan 1, 2017

By Alfred W. G. Wilson

THE state of development of its iron and steel industries serves as a 1eading index to the general condition of a nation's business affairs. In this paper, the authors present an economic study of the progress of this group of industries in Canada for the decade 1927-1936. The statistical data and most of the tables which accompany this article have been com-piled by John Casey, Statistician, Bureau of Mines; the text and some of the computations have been prepared by the seni0r author. The principal source of statistical information has been the publications of the Dominion Bureau of Statistics; where other sources have been consulted, they are noted in the text. All weights are given in short tons. Records for the years 1913 and 1918 are also presented in the group of tables dealing with iron ore and pig iron; they will serve as a basis for comparison with nearly normal years in the two decades prior to 1927-36, which included the abnorma1 years of the Great War. GENERAL REVIEW At the beginning of the decade under review, this group of industries had returned to almost normal production, as determined by pre-war conditions. Iron ore consumption showed a steady increase between 1927 and 1930; a marked decline began in 1930 and reached its culmination in 1932, when the recorded consumption of ore was 293,353 to11s, about 16 per cent of the average consumption during the first four years of the decade; the last four years of the decade show a gradual increase in consumption; the amount of ore used in 1936 was still slightly below the amount used ten years before, in 1927 (see Table 1, top).

Jan 1, 1938

By A. Burkert, A. E. Hajj

"An information system has been developed for the use of companies considering developing a new mine which may be liable to secondary sulphide ignitions or by existing operations. The system uses the Comdale X expert system to analyze information about a particular mine. The system will indicate whether the mine is likely to experience ignitions and what precautions can be taken to reduce or prevent their occurrence. The advantage of an information system using expert system and artificial intelligence principles is that it can recommend action when there is an incomplete knowledge of all the system parameters. By interrogation of the user it can determine the state of knowledge and react accordingly. It is considered that such systems could be of significant use in mine planning for new and existing properties, especially where operators have limited expertise regarding secondary sulphide ignitions. IntroductionSulphide ignitions occur in the underground mines of several countries, including Australia, Canada, Finland, South Africa and the United States of America (1·3) and there has been a significant increase in their number and severity over the last decade(2.4). The basic causes of such ignitions are not well understood and man incidents are not reported or documented.Sulphide ignitions can pose a serious threat to the health and safety of mine workers and to the cost and efficiency of the mining operation (1-5). Byberg(6) described the three major problems associated with sulphide ignitions as:1. the force of the initial explosion can endanger workers and equipment;2. the intense heat of the ignition's flame front can endanger workers and equipment and may also ignite combustible material resulting in mine fires; and3. the sulphur dioxide produced by the ignition may be of such quantity and concentration to endanger workers, as was tragically demonstrated at Geco. In this incident in October 1985, a worker was killed at a position 2400 metres from the ignition point of a sulphide ignition at Manitouwadge, Ontario."

Jan 1, 1994

By O'Halloran. Gerard F.

"ECSTALL MINING has installed in their plants the most modern equipment in the mining industry. At the minesite, digital blocked frequency controls are used to monitor all crushers, conveyors, ventilation equipment and pumps from underground. Distant pumping stations are monitored and controlled by radio. Modern friction skip and cage hoisting systems have been installed with static power supply designed for automatic operation. Rotary-type compressors of recent design are in service in place of the conventional reciprocating-type units. At the concentrator, the 800- and 1500-hp synchronous motors driving the grinding mills have static field excitation and pneumatic clutches, still meeting modern-day concepts, having been• installed in 1966. The maintenance work load has increased annually for the past eight years. The modern plant, with all the present-day sophistication, must have a welltrained and well-organized force of skilled workers, and a maintenance system which will supply realistic facts and guidelines. This presentation will review the relative location of plants, utilities, maintenance and services, plant maintenance control and mechanical control. It is the hope that enough information will be presented to weigh the size of the job and how the resources are utilized for controlled maintenance."

Jan 1, 1974

By Güney

"An investigation carried out to determine the tendency of coals to heat spontaneously in terms of time-temperature curves coupled with the resulting oxidation products in an adiabatically controlled laboratory setup is described. Tests were made at differing moisture conditions, including oxidation and also oxidation with either adsorption or desorption of water vapour on coal.From the experimental evidence, there is reason to believe that the oxidation of coal, although an important factor, is not the predominant one in the development of spontaneous heating. In addition to the temperature increase in coal and the gaseous products evolved due to auto-oxidation, the process is accelerated by adsorption and retarded by desorption of water vapour on coal."

Jan 1, 1971