Search Documents

By Shuan-cheng Gu

Roof bed separation often occurred due to the deformation incoordination of surrounding rock following the excavation of mine roadway. Bed separation has effect on the bolts, and the estimation of the influence will directly affect the safety of support systems. In this paper, the hyperbolic function model to analyze the load transfer mechanism on the bolts was simplified as the exponential function form for easy calculation. An elastic-plastic analysis model of the bolt loading occurred by the bed separation was established. And the development low that the bed separation affected to the bolt loading was discussed. According to the parameters analysis of different separation values and locations, the influence law of the bolt loading caused by roof bed separation was summarized. Finally, the effects of bed separation were considered for the bolting design, it was able to provide a reference to the anchorage design of stratified rock.

Aug 1, 2013

The Cadia mine is shifting from the open pit operation to the Cadia East underground block cave. The resulting increase in milled tonnes and the decrease in fines production through shifting to block caving require an increase of over 25% in installed power. This expansion is being accomplished via the installation of up-front crushing and HPGR milling of the ore, with the SAG mill receiving a secondary crushed feed. This design, criteria and rationale for selection is presented. Over the coming years, the mine will further expand capacity. The target is to accomplish this with minimal addition of installed power or use of fresh water. This presents a challenge that epitomizes the future constraints on our resource dependent and intensive industry. The approach and proposed options to this longer-term expansion are also presented.

Jan 1, 2012

The control of AG mills fed by ores with harder and softer components can be challenging due to the sensitivity of the mill to the ratio of hard to soft components. The mills at LKAB?s iron ore operations are generally well controlled, but there are periods when the throughput falls off dramatically, due to a loss of mill filling. As the ore is upgraded in the sorting plant through magnetic separation prior to milling, this presents an opportunity to manipulate the feed blend in advance. In order to assess this opportunity, a fullscale mill charge was dumped and assayed by size to quantify the build-up of competent waste in the mills. This was supplemented by pilot and locked-cycle laboratory tests at a wide range of feed blends in order to facilitate the development of an appropriate multi-component AG mill model. This paper reports the experimental campaign requirements and methodologies, as well as the major outcomes from analysis and modelling exercises using the industrial, pilot and laboratory multi-component data.

Jan 1, 2012

By L. E. Djingheuzian

Introduction Cylindrical grinding mills have been used for a long time, but during many years of testing no methods were established that gave consistent results. The work by both scientific investigators and operators led very often to contradictory conclusions, and each millman was very much 'on his own' when trying to find the limits for working of his ball-mills. Fred C. Bond, in the introduction to his paper on Wear and Size Distribution of Grinding Balls, freely states that the mathematical immaturity of the grinding process "is the cause of many inefficient designs and installations as well as of much poorly oriented experimental work", and evidently he sees the solution of all our grinding problems in the discovery of the fundamental laws "which can change the empirical art into a mathematically exact science". While the writer is in complete agreement with Mr. Bond that grinding is governed by fundamental laws which can be expressed by mathematical formulae, there are so many variables in grinding, all interwoven with each other and mutually influencing each other, that the coalescing and merging of all these variables into a harmonious mathematical whole appears to be a homeric job. However, a light appeared on the horizon when it was proposed that power be used as an index of the grinding operation. It is pertinent to quote Gow, Guggenheim, Campbell, and Coghill from their paper on Ball Milling, in which they say: "Much of the past literature devoted to the subject has been concerned with the Kick-Rittinger dispute over evaluating grinding, or with dissertations on ball paths and the closely allied impact versus attrition hypotheses or with the exclusive consideration of certain specific variables, such as mill speed or circulating load, irrespectve of the other factors in operation. Such subjects may be dismissed with but little discussion in what may be called, by comparison a new philosophy in the stud of ball milling. Briefly this 'new philosophy' consists ' of using power as an index of the mill operation, and investigating grinding from the standpoint of set and induced variables with emphasis on the latter". But it is safe to assume that it was the work by E.W. Davis, H. E. T. Haultain, F. C. Dyer, A: M. Gaudin, J. Gross, S. R. Zimmerley, and others, that cleared the path for the authors of Ball Milling and induced them and A. W. Fahrenwald to look farther afield and thus to establish a far-reaching relationship between the power and capacity and the diameter of the ball-mills.

Jan 1, 1949

By M. Kamyab

The Deep Exploration Technology project, as part of the Australian Cooperative Research Centre, is developing technologies to drill deep boreholes for mineral exploration purposes. The aim of the initiative is to transfer drilling technologies from oil and gas into mining applications. Several modifications have to be pondered due to this technology exchange: smaller cuttings sizes because of using impregnated diamond bits; narrower annulus space; higher drilling fluid velocity and likelihood of turbulent flow regime in the annulus; and higher pressure loss. In particular the results of our lab experiments have shown that the increase in concentration of small size cuttings can significantly change the rheology of the mud when drilling in hard rocks. This, in return, could have a noticeable increase in the pressure loss encountered along the annulus space. As a continuation of the above study, numerical simulations were conducted to investigate the cuttings transport behaviour in small size annulus space. Fluid velocity, annulus size, cuttings concentration, cuttings density, and cuttings size were some of the parameters that were varied to see their effects on cuttings transportation and the pressure loss along the annulus space. The results indicate that, due to the differences between oil and gas and mining drilling, conventional oil well planning is not applicable for mineral exploration drilling and numerical simulation would help in this matter.

Aug 1, 2013

By Rodney A. Cooper

The Mary River iron ore deposits were discovered in the 1960?s. The high quality of the deposits was immediately evident, and drilling programs were successful in defining a resource adequate for supporting a feasibility study. Through a combination of ownership, market and political forces, the deposits were not developed. Having missed the window of opportunity, the project remained dormant for over three decades. Baffinland Iron Mines Corporation, with its 100% ownership of the Mary River deposits, began trading publicly in 2004. Modern exploration and metallurgical test work began in 2004 and has continued in 2005 and 2006, resulting in total expenditures during this period of almost C$60 million. In May 2006, an engineering team lead by Aker Kvaerner E&C, a division of Aker Kvaerner Canada Inc., completed a scoping study based on the first of five identified deposits. Highlights of that study include direct shipping of high quality lump ore to Europe over a 34 year mine life at a production rate of 10 million tonnes per annum, based on an indicated resource of 309 million tonnes at 66.1% Fe and an inferred resource of 28 million tonnes at 65.9% Fe. Capital costs were estimated at C$1.5 billion. Using iron ore prices approximately 36% below that of the 2006 market, a pre-tax internal rate of return of 15% was estimated assuming equity financing. Payback on initial capital was 5.9 years. The pre-tax life-of-mine cash flow was estimated to be C$6.3 billion. As a result of this study, Baffinland initiated a Definitive Feasibility Study, under the management of Aker Kvaerner, which is scheduled for completion in December 2007. This paper touches on the geology of the deposits, the current resource and the outlook for expansion. Project permitting, construction planning, logistical challenges and ocean shipping considerations are discussed, providing a current perspective on the project scale, scope and timeline for commercial production. In addition, an overview of the Company?s bulk sampling program will be provided.

May 1, 2007

By Roméo Roussin

"The yearly production from the Asbestos Hill pit is 1,550,000 tons of asbestos ore, with a yield varying between 18 and 20 % . The orebody was exposed at the top of a hill, and initial production started without having to remove any overburden. The projected ratio of barren rock to ore, based on the present orebody, was 2 to 1. However, as it was necessary to push back the upper benches, this ratio has changed to 3 to 1. The final pit will be 2,300 feet long by 1,000 feet at the longest and widest points. The final depth will be 680 ft. A pit slope stability study was carried out and an average wall angle of 60-70 degrees must be maintained. Preshearing of final pit limits will produce good wall stability. Permanent access ramps will be 60 ft wide, with an 8 % maximum grade. Geological conditions and the low rock temperature are the major causes of the operation's drilling and blasting problems."

Jan 1, 1976

By Réal Tanguay, Mathieu Piché, Jacques Carignan, Charles Beaudry, André Bonenfant

"Le gisement Isle-Dieu est situé sur le flanc sud de l'anticlinal de Galinée. La stratigraphie locale comprend, de bas en haut, la rhyolite du Groupe du Lac Watson surmontée par le basalte du Groupe de Wabassee. Un horizon repère, siliceux et sulfure, d'origine sédimentaire, appelé ""Tuffite Clef', est présent au sommet du Groupe du Lac Watson et pend à 45° vers le sud.Le gisement Isle-Dieu est constitué par une lentille qui recoupe, en partie, la ""Tuffite Clef"". Elle est séparée en deux trorçons par un dyke de tonalite. Les données obtenues à partir des forages effectues à travers la rhyolite sous-jacente permettent de définir les zonations chimiques et pétrographiques de la cheminée d’altération.Ces transformation minéralogiques et chimiques sont caractérisées par un enrichissement en MgO, Fe2O3, MnO et un appauvrissement en CaO, SiO2 et Na2O. La zonation spatiale de ces altérations permet de mettre en évidence la géométrie et l'extension des conduits hydrothermaux. L'épaisseur maximale des sulfures massifs au sein de la lentille est en étroite relation avec l’importance des zones d'altération. Les patrons de variations chimiques dénotent une orientation préférentielle WNW des conduits hydrothermaux. Les parties les plus altérées et les plus déformées présentent localement de fortes variations positives en Zr, Nb, et terres-rares; ces concentrations sont vraisemblablement imputables a /' enrichissement résultant de la diminution du volume lors de l'altération.L'étude pétrographique montre que la porosité et la perméabilité du milieu ont joué un rôle important dans la circulation des fluides car les roches de la cheminée présentent des phénomènes de dévitrification, de bréchification et de microfracturation très prononces. La nature magnésienne de certaines chlorites et la perméabilité accrue du milieu semblent en accord avec le modelé propose par Roberts et Reardon, ( 1978 )"

Jan 1, 1990

By C. Arson

"Optimizing hydraulic fracture injection parameters in order to maximize hydrocarbon extraction and to avoid extensive borehole spalling is still an open issue. In this paper, the Differential Stress Induced Damage (DSID) model is employed to simulate the anisotropic damage distribution around pressurized boreholes drilled in fractured shale. The loading path is purely mechanical: excavation and fluid injection are simulated by stress relaxation followed by pressurization. We investigate the effect of pre-existing fracture orientation, in-situ stress and injection pressure on the propagation of anisotropic damage during pressurization. Finite Element results indicate that (1) damage initiates and develops when the ratio of two in-situ stress component deviates from 1, and the magnitude of damage is proportional to this stress deviation; (2) For a given in-situ stress field, damage initiates for a certain threshold of injection pressure, and the damage zone extends as the injection pressure increases; (3) A pre-existing fracture only affects the damage zone locally; the orientation of that fracture does not affect the damaged zone, which is controlled by in situ stress and injection pressure.INTRODUCTIONHydraulic fracturing is used to increase shale permeability and to enhance hydrocarbon extraction. In order to maximize the extraction ratio and to avoid wellbore spalling and clogging during fluid injection, the parameters related to injection for each particular site need to be optimized. Therefore, it is necessary to clearly understand how shale responses upon excavation and pressurization.It is well known that breakouts grow in the direction of minimum compression and that plastic deformation around wellbores tends to arrest breakouts (Zoback et al., 1985). Laboratory acoustic emission tests revealed that fractures propagate along the direction of maximum compression stress, and fractures (breakouts) are surrounded by the Excavation Damaged Zone (EDZ), in which rock properties are weakened by the presence of micro cracks (Eberhardt et al., 1999; Martino et al., 2004). The anisotropy from orientated foliations and cracks may influence the development and propagation of fractures and breakouts (Everitt et al., 2004). Sonic televiewer logs proved that during hydraulic fracturing, fluid injection further alters the stress distribution (Evans et al., 2005). Shale natural fabric strongly affects the evolution of the EDZ around boreholes."

Jan 1, 2015

By Dong-kil Lee

A ventilation improvement index (VII) was developed in an effort to propose an optimal ventilation improvement measure for a designated mine. The index was designed to incorporate both ventilation effectiveness and cost efficiency. To verify the effect of the index, a mine experiencing a ventilation problem was selected, the ventilation assessed and ventilation network analyses were conducted. In the selected mine, four areas with ventilation difficulties were detected and an improvement schemes for each area were proposed. These were simulated through network simulation and evaluated using the ventilation improvement index. As a result, an optimum ventilation improvement scheme was proposed. The improvement scheme with the highest VII value was incorporated in the design.

Aug 1, 2013

By E. J. Marcotte

"INCO LIMITED'S Shebandowan Mine and Mill is located in a scenic tourist and cottage area near the western tip of Lower Shebandowan Lake, approximately 90 Km west of Thunder Bay, Ontario. This nicely designed complex is a positive indication that mining operations can co-exist in harmony within the natural environment.The Shebandowan complex processed nickel-copper ore from 1973 to 1985, inclusive, after which operations were shut down.In late 1988, INCO LIMITED decided to place the Shebandowan complex back into operation, under contract, to mine and mill the remainder of the ore body, according to their specifications. MaclSAAC'S EXPLORATIONS was the successful bidder for the project. Following preliminary rehabilitation, operations were re-activated in late March, 1989. The ore mined to date is of a moderately lower nickel grade than the majority of previous years. However, a higher tonnage rate, combined with improved nickel recoveries, has contributed to a viable operation.A series of mill operating and equipment modifications has enabled MaclSAAC EXPLORATIONS to achieve the quality and grade of nickel-copper concentrates specified, and at the same time, expand mill tonnage throughput while attaining increased nickel recovenes."

Jan 1, 1992

By I. H. Warren, Forward F. A

The reduction of aqueous slurries of uranyl carbonate at elevated temperature with compressed hydrogen m the presence of metal catalysts and certain organic promoters has been shown. to yield uranium dioxide. The reduction takes place in a sequence of steps. The purity and sintering properties of the dioxide make it of interest as a starting material for fuel element production. Simple control can be exercised over the surface area and oxygen/uranium ratio of the product during reduction. URANIUM dioxide for fueling atomic power reactors 1s conventionally produced as a powder by simultaneously decomposing and reducing ammonium diuranate with hydrogen in a furnace at high temperature. Fuel elements are then generally made from this powder by compacting and sintering ( 1). In order that elements approaching theoretical density may be obtained,

Jan 1, 1961

By L. E. Djingheuzian

"IntroductionIN 1940, in a series of articles, M. W. von Bernewitz(l) reviewed in detail roasting of gold and silver sulphide ores and concentrates. Since that time some significant developments in roasting have taken place, and a number of papers have appeared in the Canadian technical literature, dealing severally with the roasting of a particular ore or concentrate.The purpose of this paper is not only to review some of these Canadian papers and bring the information on Canadian roasting practices to .date, but also to analyse the mechanism of roasting. Hence, it is proposed to start with a study of physico-cl1emical factors fundamental in roasting, the knowledge of which, by creating a sound basis for a proper roaster design, makes good roasting possible.Physico-Chemical FactorsRoasting can be defined as heating sulphide ores in presence of air below fusion points of the constituent minerals, at such temperatures as to convert metallic sulphides to oxides. Hence, roasting is a chemical process.The object of roasting is, by changing, chemically, mineral constituents of sulphide ores, to make the economic recovery of the desired •Constituent metal by a subsequent standard treatment possible. For instance, pyritic ores, containing gold in sub-microscopic form which no amount of grinding would release, are roasted in order, by oxidizing the sulphides, to open up their structures to such an extent as to enable cyanide solutions to come into contact with the gold and dissolve it. The production of porous calcine is, therefore, the object of roasting of refractory auriferous sulphide ores or concentrates. Such a porous calcine may be defined as a desirable calcine, and the roasts which produce desirable calcines can in their turn be termed desirable roasts."

Jan 1, 1952

By G. M. Swinkels

Sherritt Gordon and Cominco, with financial assistance from the Canadian Government through PAIT, have developed a hydrometallurgical process for refining copper from sulphide concentrates. The main objective of the project was to develop a process applicable to a wide range of concentrates with respect to copper content, other metals content and impurities, within the economic parameters set by present smelting and refining practice. Other important objectives were to recover sulphur in its elemental form and not as sulphur dioxide to assure improved hygienic conditions and a negligible impact on the environment. For the most abundant and relatively refractory chalcopyrite concentrates, the first step of the process is thermal activation with hydrogen to decompose chalcopyrite and pyrite, commonly associated with it, into more reactive sulphides more amenable to leaching. The iron is then selectively extracted by sulphuric acid leaching and subsequently rejected as jarosite. High-bornite concentrates do not require thermal activation and acid leaching; they are subjected to another hydrometallurgical iron removal step. The high-grade copper sulphide resulting from iron removal, and containing all of the initial precious metals, is then leached under oxygen pressure to produce elemental sulphur and copper sulphate solution . After suitable solution purification, the copper is recovered by high-current-density electrowinning as wire-grade product. Precious metals remain in the leach residue and are recovered after separation of the gangue materials and elemental sulphur. The laboratory and pre-piloting test work had indicated copper and precious metals recoveries comparable to those achieved in current practice. The process was shown to be suitable for handling relatively low-grade concentrates and, in addition, it was capable of high recoveries of associated zinc, molybdenum, nickel and cobalt in saleable form.

Jan 1, 1978

By Daniel J. Schulze

Abstract-Eclogite is an important source of diamond in the upper mantle, but is more localized than peridotite. Using eclogitic minerals in kimberlite and diamond exploration is also more problematic than using the well-known peridotite-derived indicator minerals Cr-pyrope and magnesiochromite. The problems include color similarities between orange garnets from eclogites, Cr-poor megacrysts, and crustal garnets, chemical similarities with Cr-poor megacryst suite garnets (specifically elevated Na2O contents), and low abundance of eclogite garnet xenocrysts in most known kimberlites. Chemical screens must be used carefully to distinguish between varieties of orange garnets in exploration samples. For example, most orange garnets of crustal origin have >22 wt% FeO, with mantle eclogite garnets having lower values. Na2O-bearing garnets from the Cr-poor megacryst suite can be distinguished from Na2O-bearing garnets from diamondiferous eclogites by the elevated TiO2 contents of the former. The low abundance of eclogite garnet xenocrysts in kimberlites worldwide, however, may dictate that use of eclogite garnets in diamond exploration in most cases be restricted to advanced stages of kimberlite exploration and evaluation of kimberlite diamond potential. Crpyropes, Mg-ilmenites and Cr-rich chromites are more useful than eclogitic garnets in most stages of diamond exploration. If orange garnet xenocrysts are sought in a kimberlite exploration program, those from the Cr-poor megacryst suite will be more useful than eclogite derived garnets, due to the typical great abundance of the former, although they carry no information of the diamond potential of the host kimberlite.

Jan 1, 1997

By Daniel J. Schulze

Eclogite is an important source of diamond in the upper mantle, but is more localized than peridotite. Using eclogitic minerals in kimberlite and diamond exploration is also more problematic than using the well-known peridotite-derived indicator minerals Cr-pyrope and magnesio-chromite. The problems include color similarities between orange garnets from eclogites, Cr-poor megacrysts, and crustal garnets, chemical similarities with Cr-poor megacryst suite garnets (speci?cally elevated Na2O contents), and low abundance of eclogite garnet xenocrysts in most known kimberlites. Chemical screens must be used carefully to distinguish between varieties of orange garnetsin exploration samples. For example, most orange garnets of crustal origin have >22 wt% FeO, with mantle eclogite garnets having lower values. Na2O-bearing garnets from the Cr-poor megacryst suite can be distinguished from Na2O-bearing garnets from diamondiferous eclogites by the elevated TiO2contents of the former. The low abundance of eclogite garnet xenocrysts in kimberlites worldwide, however, may dictate that use of eclogite garnets in diamond exploration in most cases be restricted to advanced stages of kimberlite exploration and evaluation of kimberlite diamond potential. Cr-pyropes, Mg-ilmenites and Cr-rich chromites are more useful than eclogitic garnets in most stages of diamond exploration. If orange garnet xenocrysts are sought in a kimberlite exploration program, those from the Cr-poor megacryst suite will be more useful than eclogite derived garnets, due to the typical great abundance of the former, although they carry no information of the diamond potential of the host kimberlite.

Jan 1, 1997

By W. J. Asselstine

Introduction This paper is prepared from data gathered for a similar paper to be submitted to the United States Bureau of Mines, for publication as one of their information circulars. It covers the history and development of the present milling practice at Premier. The authors wish to acknowledge the assistance and suggestions given during the preparation of this paper by D. L. Pitt, Manager of the Premier Gold Mining Company, Limited; also their indebtedness to various members of the Engineering Staff and of the Accounting Department who have assisted materially in gathering the data used. Location The Premier mine and mill are situated in northern British Columbia, approximately fifteen miles north of the head of Portland canal, in the Salmon River section, about half a mile east of the Alaska-British Columbia boundary line where it crosses die Salmon river. The mill is located on a rather steep hillside on the horizon of the main haulage level of the mine, and is within a hundred feet of the mouth of the tunnel. Both the mine and mill are connected with tidewater at Stewart, B.C., by an aerial tramway (1) eleven and one-half miles in length, which delivers both ore and concentrate to the bunkers at the dock for shipment to the smelters. All mine and mill supplies are transported from Stewart dock to Premier over this tramway, except heavy machinery. Heavy pieces have to be hauled either by truck in summer or sleighs in winter over a good road which runs from Stewart dock to Premier.

Jan 1, 1933

By K. Huang, L. Pan

"Darcy’s law has been used extensively to model cake filtration. It is a macroscopic model, in which particle size dominates the kinetics and cake moisture. In the present work, a capillary flow model has been developed from first principles to study the effects of microscopic parameters such as capillary radius, boundary layer slip, disjoining pressure, and surface tension that may be important for dewatering ultrafine particles. Laboratory-scale pressure filtration tests show that dewatering kinetics is strongly dependent on capillary radius, which in turn is influenced by surface hydrophobicity, surface charge, and length scales of particles. The model parameters determined from laboratory-scale filtration tests show that use of a hydrophobizing reagent can greatly improve fine particle filtration due to increased slip and decreased capillary pressure. The kinetics of dewatering kaolin clay is fastest at a pH where the layer-structured particles coagulate with a face-to-edge orientation. The capillary flow model developed in the present work may be useful for designing filters and optimizing operating conditions.INTRODUCTIONIn 2014, Canada produced 2.2 million barrels per day of crude oil from the oil sands resources in Alberta, which is expected to grow to 3.2–4.0 million barrels per day by 2030 (CAPP, 2013). One of the challenges to meeting these projections is the tailings management. At present, the industry uses ?77 km2 of the lands to construct tailings ponds. Significant amounts of the tailings disposed to the ponds are silts and clays that are slow to settle and consolidate, creating problems for reclamation. It is, therefore, the objective of the present work to develop a filtration model that may be useful for developing advanced dewatering technologies that can address the tailings management issues.Darcy’s equation is the governing law for filtration. It was derived as an empirical model by H. Darcy in 1856 while he was studying fluid flow in sand filters (Hall, 1956). Since then, many investigators derived it from first principles. It relates superficial fluid velocity to the pressure drop across a porous medium of known permeability. In filtration, the latter can be related empirically to particle size using the Kozney equation (Yoon, 2005)."

Jan 1, 2016

By J. P. Dick

THIS paper is a description of the milling practice and metallurgy at the Moneta Porcupine mine, Timmins, Ontario. The results obtained with an all-cyanide circuit and later with flotation followed by cyanidation are described. The ?investigation which prompted the various changes in milling practice have also been dealt with. Moneta ore is possibly the most refractory now being milled in the Porcupine district. This is due to the ultra fine state in which the gold occurs and to its intimate association with pyrite. No doubt there is ore of similar characteristics on the neighbouring properties but it probably forms only a small portion of the tonnage being mined, whereas at Moneta the bulk of the ore requires an extremely fine grind to liberate the gold. The fineness to which an ore can be ground economically has gone far beyond what was thought to be the limit only a few years ago. Formerly, a set of standard screens was all that was required to measure the fineness to which an ore was ground. At present, the Haultain infrasizer is practically indispensable, and the nominal micron has become a familiar unit of measurement to all those dealing with the problems of fine grinding.

Jan 1, 1941

By M. E. Holuszko

Although there is no widely accepted rigorous definition of handleability, the handling coal characteristics often referred to as handleability define whether a coal has the ability to flow unhindered through the processing and transportation systems. The handleability may be severely affected if fine coal particles tend to aggregate. In the pelletization process, the rolling action of the drum is applied to bring the individual particles into proximity with each other so that they can aggregate and form pellets. Because of apparent similarities between these two processes, the pelletization tests are carried out in parallel to the handleability tests in this project, and the pelletization results are used to explain coal handleability properties.

Jan 1, 2004