Search Documents

By T. Mulpeter, G. Deschênes

Sadiola Gold Mine is an open pit operation located in Mali and owned by Anglogold Ashanti Ltd, Iamgold Corporation and the State of Mali. A conventional cyanidation process (cyanidation/CIP) treats 15,000 tpd (of a mixture of oxide and sulphide ores) at an average grade of 3 g/t Au. In 2002, the increasing tonnage of sulphides caused an increase in production costs and a decrease in gold extraction (from 95% to 70-76%). Because of the short retention time of the leach circuit (18 hours) and the refractory nature of the sulphides, gold leaching kinetics are critical. A laboratory investigation was initiated to evaluate actual plant practice and identify a means of improving the gold leaching rate. The study was conducted on a "soft" sulphide gold sample containing 4.96 g/t Au, 0.4 g/t Ag, 2.5% pyrite, 1.2% arsenopyrite, and 0.2% pyrrhotite with a P80 of 74microns. Pre-leaching significantly influenced the gold leaching rate. A short pre-leach (2 hours) performed at pH 8, a DO of 8 ppm, and with 300 g/t lead nitrate added at the start or the end, produced the preferred conditions. Pre-leaching for more than 2 hours was detrimental to gold extraction. The cyanide concentration had to be maintained at 450 ppm NaCN to reach a maximum gold extraction within the retention time of the circuit. A maximum extraction of 81.3% Au was obtained in 20 hours (leach residue at 0.97 g/t Au). A high level of dissolved oxygen in the pre-leach was not of any benefit. Extension of gold leaching beyond 20 hours indicated that all leachable gold had been extracted by that time. Plant modifications were made to allow leaching of oxides and sulphides in separate circuits. Treatment of oxide ores is now performed at a higher rate. Sulphides are processed at a lower throughput, with 300 g/t lead nitrate, to allow a retention time of 22 hours. Combined throughput remains the same, and total gold recovery has increased from 76% to 80% for an additional gold production of 16,000 ounces per year.

Jan 1, 2005

By Seungyeol Lee

Currently, a new construction method using a robotic system is widely spreading in construction sites. This study is related to the design of glazing robot?s teach pendant which can improve convenience of handling and hence improve the productivity through the efficient interaction between an operator and a robot while doing glazing works, e.g., curtain wall installing. The suitability of selection and arrangement of control switches was assessed according to mechanical motions of a glazing robot, and design guidelines for improving convenience and productivity were drawn up through questionnaires carried out by site operators. To verify the proposed design guidelines, working time comparison of the proposed teach pendant and the existing teach pendant was executed.

Aug 1, 2013

By M. Piboule et J. M . Charbonneau, C. Picard

In the western part of the Chapais syncline (Abitibi-east, Quebec), the lava flows belonging to the Haliy Formation separate in two distinct sequences. The basal sequence contains prophyri tic metabasalts of calc-alkaline af f inity overlain by porphyritic metatrachyandesites and metatrachytes of alkaline to shoshonitic affinity. The upper sequence contains porphyritic metabasalts similar to those of the basal sequence along with highly potassic metaandesites trending to a subalkaline affinity. A geochemical study of trace and REE elements established that the composition of these lava flows results from a mixing or contamination process. The primitive tholeiitic liquids which are enriched in LREE were modified by the addition of a crustal contaminant enriched in Y, Zr, Th and K20. The magmatic liquids resulted from successive steps in the admixing process, evolved by fractionated crystallization. The mechanism of gradual admixing seems to be the major cause of the observed ea le-alkaline characteris ties and may also be the cause of the alkaline to shoshoni tic affinity in those lavas. The tendency to differentiation by fractional crystallization reveals the tholeiitic character of the primitive liquids.

Jan 1, 1984

A pilot scale AG milling campaign was conducted at the AngloAmerican Platinum pilot plant in South Africa. Different blends of hard:soft (silicate:chromite) and coarse:fine particles in the AG mill fresh feed were tested. The effects of multi-component feed on the pilot scale autogenous grinding are presented in this paper, and can be used as a guideline for multi-component feed blends for AG milling. Preliminary modelling and simulation for the multi-component AG mill model are also included.

Jan 1, 2012

By M. R. Julien, A. Maqsoud, J. Martschuk, B. Bussière

Acid mine drainage (AMD) from mine wastes is one of the most challenging environmental problems currently facing the mining industry. When mining wastes have the potential to produce AMD, the effluents produced have to be managed to meet existing regulations on water quality. The LTA impoundment (property of Barrick Gold Corp.) located near Malartic, Quebec, contains sulphide tailings that have the potential to generate an acidic leachate. The closure option selected by Barrick was to construct a cover with capillary barrier effects (CCBE), in which the moisture- retaining layer is made of non-acid-generating tailings. Since its construction in 1996, the cover has been monitored to evaluate its performance. For that purpose, various parameters have been measured, including the volumetric water content and matric suction in the different layers of the cover. This paper presents some of the main results from the monitoring program that started eight years ago. The results show that the cover is able to maintain a high degree of saturation in its moisture- retaining layer, acting as an oxygen barrier. The actual performance of the CCBE on the flat surface of the 60 ha site is better than expected at the design stage. The only concern with the LTA cover is the effect of slopes that can reduce the performance of the CCBE during dry periods. However, these effects appear only for short periods of time, and are limited to very localized areas, so that they do not significantly affect the overall performance of the CCBE and its ability to limit the production of AMD.

Jan 1, 2006

By Michael Samis

The real option valuation method is often presented as an alternative to the conventional discounted cash flow (DCF) approach because it is able to recognize additional project value due to the presence of management flexibility. However, these two valuation methods can be separated on a more fundamental level by their differences in risk discounting. Real option valuation applies the risk-adjustment to the source of uncertainty in the cash flow while the DCF method adjusts for risk at the aggregate level of net cash flow. This seemingly small difference is the reason why the real option method is able to differentiate between projects according to each project?s unique risk characteristics while the conventional DCF approach cannot. This paper provides an overview of the real options and DCF valuation frameworks and discusses the differences in risk discounting that exist between the two methods. Using grade-school mathematics, this paper clearly demonstrates how, with real options, a unique project risk discount can be calculated which is directly linked to the project?s unique risk profile. It also highlights why the DCF method fails in this regard and shows why a call to ?increase the Risk-Adjusted Discount Rate? is an incomplete solution at best. Finally, a heap-leach project and satellite reserve development project are valued with both techniques and the difference in investment conclusions is explained in terms of the risk-discounting concepts discussed here.

May 1, 2003

By R. Argane

In this work we assessed the geochemical behavior of concentrator tailings deposited at the abandoned mines of Zeida and Mibladen (Upper Moulouya, Morocco), using physico-chemical analyses, mineralogical characterization, acid base accounting and weathering cell tests. The aim of the study was to evaluate mine drainage quality and to assess metal mobility from these concentrator tailings. Chemical analyses show that the Upper-Moulouya abandoned tailings contain relatively high quantities of lead (0.261 to 0.594 % wt). Mineralogical analyses reveal the abundance of neutralizing minerals (calcite, dolomite, ankerite, and aluminosilicates) which influence mine drainage and metal mobility in mine tailings. Leachate analyses from weathering cell tests show alkaline conditions, small conductivity values, and low solubility of Pb-mineral phases. According to these results, abandoned mine tailings in the Upper-Moulouya district have very low potential for generation of contaminated mine drainage and for leaching of heavy metals. However, the inhalation of tailings exposed to winds generate dust problem facing the local population and may cause health consequences.

Aug 1, 2013

By C. G. Anderson

Industrially proven and applied nitrogen species catalyzed (i.e. NSC) acidic pressure leaching has been utilized to treat a number of ores, concentrates and recycled materials. This versatile technology offers many advantages including low temperatures, low pressures, low capital costs, low operating costs, faster throughput and less costly materials of construction than conventional pressure oxidation. This paper will elucidate the application of this technology for production of gold, silver, palladium, rhodium, zinc, germanium, gallium, cobalt, copper and nickel. Recycled material applications will also be elucidated. In addition, details of an application for treatment of a refractory chalcopyrite copper and gold bearing ore will be presented and pertinent economics discussed.

Jan 1, 2004

By David Nicholls

?Overview of New Afton ?Reserves and Resources ?Geology and Mineralization ?Exploration ?Capital Project Development to Date ?Mine Development ?Processing ?Construction ?LOM ?Health, Safety, Environment and Social Responsibility Overview of New Afton ?Fully owned by New Gold Inc ?Large gold-copper porphyry deposit, amenable to block cave mining, production commencing in 2012 -1 million ounce gold reserve -1 billion pound copper reserve -Estimated 13 year mine life ?Low operating cost ?Estimated capital expenditure requirements -Spend to date ?US$200million -Remaining to be spent ?US$400milllion ?Robust economics ?Excellent location and infrastructure ?Significant cash flow contributor for the Company

May 1, 2010

By T. A. Utigard

To improve recoveries of Ni, Cu and Co in the Inco flash furnace, a new operating concept was investigated. By adding sufficient coke to form a supernatant coke layer, a reducing barrier would form allowing for improved reduction of descending oxidized sulfide mineral particles formed in the flame. The objective of this investigation was to study the kinetic mechanism and efficiency of the coke layer to produce a sulfur deficient matte. The mechanism and rate of carbon reduction of each of the phases formed in the flash flame, i.e. sulfides and oxysulfides were investigated by means of X-ray visualization tests. Graphite-slag reduction was also conducted for comparison purposes. In the case of slag, poor wettability and the formation of a gas film on the surface of the carbon reductant are often blamed for limiting the reaction surface area that ultimately results in poor reaction kinetics. The X-ray visualization tests confirmed that matte and oxysulfide wet coke better than slag and that the rates of reduction of matte and oxysulfide are faster than that of slag.

Jan 1, 2005

By K. Szczesny

This paper considers the integration of uncertain real-time logistics data for reactive construction scheduling. In order to manage a construction project efficiently, an accurate schedule representing the current project progress is inevitable. The quality and up-to-dateness of such a schedule depends on the availability of real-time data. Typically, real-time logistics data contain information about the availability of material, equipment and personnel as well as delivery dates and site conditions. The accuracy and inherent uncertainty depends on the location where the real-time data was acquired. Currently, the integration of such data into a construction schedule is a very time-consuming, manual and, thus, errorprone process. Therefore, this paper proposes a methodology that enables an automatic integration of such uncertain data into construction schedules. By integrating uncertainties into the existing schedule their impacts on the construction work can be evaluated. For this, discrete event simulation is applied. In order to model uncertain input parameters for simulation models this methodology applies the fuzzy sets theory. In combination with alpha-cut sampling technique, discrete model input parameters are obtained. By applying reactive scheduling with several discrete event simulation experiments, the results can be used to modify construction schedules according to agreed timeframes and costs. In order to demonstrate and validate the presented approach an example is conducted.

Aug 1, 2013

By H. Hamza

Efficient and effective management of extraction process tailings is an essential ingredient for the continued success and development of Alberta's vast oil sands resources. Open-pit oil sands operations north of Fort McMurray recover bitumen from flotation circuits. Process tailings are managed in carefully engineered and monitored external tailings management facilities and in below-grade mine pits. In order to support reduction of production costs and improve upon established tailings management practices, CANMET has been working with the oil sands industry in a collaborative framework to assess the potential to integrate thickened tailings into oil sands extraction process flowsheets. Albian Sands has commercialized the process while others, including Syncrude Canada Ltd., continue to evaluate the suitability of the process for their operations. This paper provides an update on R&D work undertaken in recent years to assess and develop the potential of thickened tailings technology for the open-pit oil sands operators of northern Alberta. The aim of this work was to explore opportunities to optimize process efficiency and environmental sustainability by improving water and energy conservation and develop more alternatives for tailings management and reclamation.

Jan 1, 2004

By M. A. Tomlinson, A. Di Feo, T. C. Cheng

"Goldcorp is evaluating the potential for economic reprocessing of historic tailings at several sites, including the Aunor A facility located in Timmins. The overall project is investigating the ability to recover value, remove sulphide minerals and alternative tailings re-deposition strategies. Desulphurization of tailings will eliminate potential acid generation while improved tailings re-deposition could reduce long-term liabilities and closure costs. Through a task-share project between CanmetMINING and Goldcorp, tailings obtained from Aunor A site have been characterized using mineral association analysis and diagnostic separation techniques. The selected tailing samples contain about 2 g/t of gold. Mineralogical analysis has identified coarse agglomerates bound with gypsum and significant free gold, confirmed by high recoveries in cyanide leach tests. However, despite no evidence of surface passivation on the minerals, conventional flotation techniques were found to be ineffective in concentrating gold or sulphides due to the high fines content and highly agglomerated particles.INTRODUCTION Aunor Mine is one of the historic mines that belongs to Porcupine Gold Mines (PGM) in Timmins, Ontario. PGM has undertaken an extensive mine closure program to remediate the legacy and closed mines with the funding supported by operating mines since 2006. Over the course of 100 years of operation in the Porcupine camp, it is estimated (Stevens et al., 2013) that about 130 million tonnes of tailings have been generated. Aunor Mine produced 2.5 million troy ounces of gold between 1940 and 1984, while processing over 7.6 million tons of ore. The original gold grade of Aunor Mine ores was about 10 g/t. With 95% gold recovery at the time, an estimate of 0.5 g/t of gold remains in the Aunor Mine tailings. Aunor Mine has two tailings impoundment areas: designated as Aunor A and Aunor B. The two sites are similar in size, about 7 hectares each. The amount of tailings in the Aunor A site alone is about 3.2 million tonnes. In 2017, bulk tailings were sampled from five designated locations in Aunor A. They were characterized using mineral association analysis and diagnostic separation techniques. The bulk tailings samples contained about 10% total sulphur, 10% iron, 2% arsenic and 2 g/t of gold. The prime objective of this collaborative work between CanmetMINING and Goldcorp is to facilitate the timely development and deployment of innovative tailings reprocessing solutions, specifically in the areas of desulphurization, and recovery of metals. This work targeted specific tailings of interest to Goldcorp which goals are to improve its environmental footprint and to reduce long-term liability. Thus, it is imperative to look for innovative reprocessing options that can overcome not only technological challenges but also achieve economic benefits to offset the costs associated with reprocessing the tailings. Moreover, the greater goal is to demonstrate and deploy tailings reprocessing solutions to solve one of the industry’s most difficult challenges for a sustainable mining industry in Canada."

Jan 1, 2019

By Unkown

The Province-wide road ban on movement of heavy loads has had the effect of curtailing or stopping development in several areas. In the Leduc area, the discovery well has been restricted in flow to only a fraction of normal due to limited storage space, but drilling at Imperial Leduc Nos. 2, 3, and 4 has been continued for the past few weeks. The No. 2 well is within 100 feet of the producing horizon and should be completed within the next few days. According to reports, it has been logging slightly lower, structurally, than the discovery well, but, regardless of the outcome, it has been an important test to determine westerly cross-section of the Leduc structure. No official reports have been made available of any tests made during the drilling of the well, but it is understood that promising oil and gas shows have been indicated in higher formations. Actual drilling operations have not been commenced by any of the other companies holding leases in the immediate area but it is expected that, when road bans are removed and equipment is assured, several wells will be commenced. Announcement has been made that Imperial Oil, Limited, will drill a well near Battle lake, about thirty-five miles southwest of the Leduc field. Location of the well has been made following an extensive seismograph survey of the area, with total depth of the test well expected to be in the 8,000- to 8,500-foot range. Drilling will be done with the heavy-duty rig last used at the De Winton test. Imperial Oil have abandoned hope of oil production in the Provost area after drilling nine wells, but will retain their interest in the gas field that has been developed. Of the wells drilled, four indicated gas flows ranging from 1,060 to 13,200 M.c.f. per day.

Jan 1, 1947

By Anita Marks

In 2007 Copper Mountain Mining determined that there were sufficient resources to consider reopening the Similco Mine near Princeton, BC. The mill facility that had been built by Newmont Mining in 1972 was closed in 1996 and all of the process equipment removed. The mill had been built on the west side of the Similkameen River to facilitate mining of the Ingerbelle Deposit. In 1980 construction was completed on a primary crusher and cable belt to deliver ore across the Similkameen River from the Copper Mountain deposit to the Ingerbelle mill. With the decision to restart mining of the Copper Mountain deposit, the decision was made to design and build a 35,000 tpd grinding and flotation mill near the mining operations. This paper discusses the application of historical operating data for the selection of the mills for the new grinding circuit and provides an overview of the grinding circuit design.

Jan 1, 2012

By K. Cybulski

Coal dust explosions still remain the main hazard in the coal mining sector, notwithstanding their relatively wide recognition compared to other hazards and the development of effective methods of prevention. Coal dust explosions are still the cause of numerous catastrophes, often leading to fatalities. Fortunately, they rarely occur, and it is for this reason that their hazardous impact is often underestimated. This problem in Poland is being exclusively solved by the Central Mining Institute, Experimental Mine Barbara. Here, basic research on the phenomenon of coal dust explosions and prevention methods is carried out, as well as investigations into the causes and circumstances of past accidents. After 15 years of no coal dust explosion accidents in Poland (1987?2002), a few coal dust explosions have recently occurred, with tragic consequences. These events have taken place not only in hard coal mines, where the presence of dangerous coal dust is the result of common production cycle, and safety measures against coal dust explosions are subject to specific regulations, but also in coal-fired power plants. This is of special concern because prior to 1987, such accidents had been been reported only for coal mines and not for coal-fired power plants. In recent years, two dust explosions occurred in Polish power facilities: the Dolna Odra and Turow power plants. In both cases, coal dust explosions occurred in the fuel supply system, but biomass dust was also involved. The explosions caused significant damage to the systems and buildings. This paper gives description and schematics of the regions of catastrophic coal dust explosions that have occurred in recent years in Poland, as well as the results of post-accident investigations, presenting the coal dust explosion hazard at the accident scene The results specify in detail the state of safety measures against coal dust explosions in light of the relevant regulations in force, including amount of deposited coal dust, content of incombustible matter in coal dust, free moisture content in coal dust, state of coal dust explosion safety zones, and state of explosion barriers. The conclusions from the site inspection and post-accident investigations presented enable us to determine locations of explosion initiation, probable ignition sources, range of explosion flames, and explosion barrier performance. A complete elimination of coal dust explosion hazard at the site of dust deposition is practically impossible to achieve. Similarly, a total elimination of ignition source, which may be related to the occurrence of other natural hazards, equipment malfunction or human errors, is impossible. The examples of tragic events that took place in Polish coal mines and coal-fired power plants highlight shortcomings and mistakes made in terms of assessment and prevention measures taken against the coal dust explosion hazard.

Aug 1, 2013

By S. B. Kang

Magnesium has poor ductility at temperatures lower than 225°C and, as a result, Mg alloy sheets are produced via fairly complex thermomechanical processes consisting of numerous sequential steps of hot (warm) rolling with low reduction and intermediate recrystallization annealing operations. In context of the present study, a simple technology for the fabrication of magnesium sheets by hot (warm) rolling was applied to various magnesium alloys. The misch metal addition in those AZ alloys was done to evaluate the deformation behavior. Tensile tests were carried out for those AZ alloys after applying different heat treatments. The precipitation of ß phase (Mg17Al12 phase) induced different microstructures with various cooling method from solution treatment temperature, and also with various annealing treatment temperatures.

Jan 1, 2006

By Bennett McLaughlin

AGNICO-EAGLE started sinking the Penna Shaft in 1995 with a hoisting plant capable of hoisting 1,800 tonnes per day from a 2,240 metre deep shaft. Exploration success lead to the installation of a hoisting plant capable of extracting 4,500 tonnes of ore and 1,800 tonnes of waste per day from a depth of 2,210 metres. The introduction of a new rope selection factor, permitting a safety factor of 4.0, represented the breakthrough required for a cost-effective project. This paper describes the process taken to introduce the new rope selection factor and its impact on the original plant.

May 1, 2001

By J. Schick, V. Granger

Nowadays, all French former uranium mining sites are remediated and redeveloped. If needed, mining waters containing radium have to be treated before discharged into the environment. Classical radium treatment consists in a (Ba,Ra)SO4 salt precipitation and radium monitoring was carried out using a time-consuming analysis called emanometry. Three zeolite samples have been tested to remove 226Ra from mining water. In batch experiment, radium was totally (R=100%) and quickly removed after 2 minutes contact time. Continuous sorption experiments were carried out through a vertical column at lab scale. Chabazite is the most efficient zeolite with an 226Ra activity below 0.2 Bq/L until 60000 Bed Volume. Chabazite is always efficient although radium content in material reaches 150 Bq/g. 226Ra uptake was also tested at semi-industrial scale on a pilot plant. More than 3000 m3 were successfully treated with a radium content below 0.1 Bq/L. The environmental impact assessment of Ra-chabazite was characterized by using batch leaching tests made according to the NF EN 12457-2 standard as applied on all wastes. Ra-chabazite stability is excellent during this test: radium leaching is very low, less than 0.005%. A new 226Ra measurement method was developed by ICP-MS for a better analysis reactivity. This new method was carried out in a couple of minutes with a lower sample volume than emanometry. The validation was performed according to the French NF T90-210 standard for the calibration function definition, the limit of quantification, the accuracy and the interferences.

Jan 1, 2020

By U. Caliskan, S. Miskovic

Gravity separation is a technique that depends on the difference in density of minerals for their separation. Although this method is one of the oldest separation techniques, it is still preferred in the industry because of its low capital and operating cost while it is environmental-friendly. In this paper, we present a new numerical methodology that can be used to investigate dynamics of dense slurry flows in gravity separation systems. A simple channel with a set of riffles is selected as a test platform in order to observe the effect of the riffle shape on segregation profile of particles with different densities. It is believed that the riffle shape would affect the slurry flow and possibly cause one class of particles to segregate within the riffle zone. The turbulence, as a disturbance effect within the riffle zone, causes heavy particles to displace the light, that is, the heavy particles will be trapped in riffles, while the lighter particles are carried by water to the end of the channel, which is an example to uninterrupted suspension. MP-PIC model in OpenFOAM is used to study the effect of riffle shape and slurry percentage of solids in this simple gravity separator on particle segregation profile of four discrete mineral density classes, which are Quartz/Clay (SG 2.6), Pyrite (SG 4.2), Chalcopyrite (SG 5.1), and Gold (SG 19.32). Gold particles are found to be readily captured and retained in the riffles because of their high density, while particles with the intermediate densities are more influenced by the flow. The developed model framework has been proven robust and capable of providing physical results even for the flows with a very high percentage of solids, characteristic for mineral processing operations. INTRODUCTION Gravity-based ore concentration techniques make use of differences in density of minerals within an ore to enable separation of valuables from the gangue. As some of the oldest techniques used for ore beneficiation, they are known to offer a range of benefits such as low specific energy consumption and low capital and operating costs (Burt, 1999; Falconer, 2003; Holland-Batt, 1998), however, they suffer from low selectivity, poor separation efficiency, and low capacity. Gravity separation techniques are common practices in the mining industry and are employed widely for the precious mineral concentration, iron ore recovery and coal preparation (Kroll-Rabotin, Bourgeois, & Climent, 2013; Laplante & Spiller, 2002; Williams, 1997). For example, gravity separation systems are highly applicable for precious metal enrichment operations by being included in primary grinding circuits, shaking table tailing separation, pre-concentration of leach feed and flotation concentrate enrichment for both flash and conventional flotation purposes (Burt, 1999; Falconer, 2003; Holland-Batt, 1998; Laplante & Spiller, 2002; McAlister, 1992). Gravity separation can be employed in the copper processing circuits by being integrated into the pre-flotation circuit to capture the gravity recoverable gold (GRG) and any free copper aiming to enhance the gold and copper recovery of the plant. When native copper and GRGs are present in the deposit, this integration not only facilitates plant overall performance via removal of the valuables early in the circuit, but it also reduces downstream operational expenditures due to less retention time of coarser copper particles in the system.

Jan 1, 2019