Search Documents

By Lionel A. York

THE first application of the cementation process took place in the year 1864, according to H. Standish Ball, when a break in the brickwork lining at a depth of 270', in one of the Rhine Preussen pits near Homburg, was sealed by running in milk of cement from the surface by means of a small hand pump. At about the same time Monsieur Portier adopted the method in France for repairing breaks in shaft lining. Figure 1 is descriptive of the Portier system and is of interest when compared with modern practice. During the next thirty years numerous attempts were made to improve the process; the general method used in sinking being to put clown bore holes outside the perimeter of the shaft for the purposes of injection. The cementation process was first recognized as an important as-set to mining in 1896 when Monsieur A. Francois developed his method of boring and injecting inside the shaft below the permanent water level. The Francois cementation process rapidly attained fame on the Continent and many shafts were sunk by its use in France, Belgium and

Jan 1, 1961

By W. J. Taylor, T. D. Parris

"Over 90,000 feet of raise have been bored at International Nickel underground mining operations throughout the Sudbury District since the advent of raise boring in the early part of July, 1964. With a total of 10 raise borers on hand at this time, techniques have improved steadily since introduction at INCO mines. The first unit, designed for use in rock of low compressive strength, had to be modified and redesigned to cope with Sudbury Area Precambrian rock. As equipment and boring techniques improved, a specially designed machine for larger holes was developed and is now in use. More powerful units, with a thrust capacity of up to 750,000 pounds, are under investigation. Raises have been bored up to 84-inch diameter, and the changeover to 5- and 6-foot flat reaming heads with improved cutter design has increased performance substantially. As a result, 5-foot-diameter raises have been completed to a length of 750 feet and 6- and 7-foot raises to over 500 feet. Reference is also made to the drilling of over 23,000 feet of drainage and sand-fill holes, ranging up to 7% inches in diameter, with smaller underground rotary drill equipment.Finally, a look into the future indicates the need for further improvements in equipment design to permit economic boring of 7- to 8-foot-diameter raises in Sudbury Area ground types."

Jan 1, 1972

By F. Ajersch, M. Rigaud, M. Jallouli

"Le gonflement des boulettes d'hématite à été étudié à l'aide d'une méthode de mesure standard ISO ainsi qu'à l'aide d 'une méthode de mesure dilatométrique.La première méthode a servi à l'étude des boulettes haute silice (5% SiO2) dont l'indice de basicité (IB = CaO + MgO -i- SiO2 + Al2O3) a été ajustée soit à l'aide d'une addition de dolomie, soit à l'aide d'une addition de pierre à chaux, soit à l'aide d'une addition de ces deux composes. L'indice de basicité variait de 0.05 à 0.12. Les résultats de gonfle ment obtenus à 1000?C dans une atmosphère de 40 CO - 60 N2 ont permis de montrer qu’indépendamment de l'indice de basicité c'est la dolomie qui contribue le plus à diminuer le gonflement par rapport à la pierre à chaux. L'utilisation de l'indice de basicité comme critère de sélection des boulettes est discutée.La méthode dilatométrique a servi à l'étude du gonfle ment de deux types de boulettes préparées à partir de deux concentrés de fer et dont la teneur en silice a été fixée à 2.5% et 0 5%. Ces deux types de boulettes ont reçues les mêmes additions de liant en quantité et en nature. La détermination en continue du gonflement, à 950?C dans 40 CO - 60 N2, a permis d'une part de mieux cerner le niveau de réduction auquel correspond le maximum de gonflement et d'autre part de montrer que l’allure des courbes de gonflement est étroitement liée à la nature du liant. Une augmentation de la teneur en silice des concentres contribue à diminuer le gonflement des boulettes.Des essais de réduction de gonflement non isothermes ont été réalisés à des montées de température à 10 et 20?C/min. Les résultats indiquent que le gonflement déterminé dans les conditions non iso thermes est inferieur à celui obtenu lors des essais isothermes. On discute alors de la validité des essais standards de gonflement qui sont utilisés pour prédire le comportement des boulettes lors de leur réduction dans un haut fourneau."

Jan 1, 1983

By J. Shahabpour

"Many porphyry copper deposits of the Kerman copper province in central Iran are associated with a consistent structurally con-trolled main drainage pattern, which is shown in this paper to be a useful regional prospecting tool in the search for new deposits. The main drainage trends also generally allow the distiction of high-grade (>0.2% Cu) from low-grade (<0.2% Cu) deposits. Topographic maps1:50 000 or geologic maps 1:100 000 have been found suitable for identification of promising drainages.IntroductionTrends of the main drainage systems transecting the high-grade porphyry copper deposits of the Kerman Region in Iran coincide with Quaternary age regional faults and fractures. Observation of such drainage trends can expedite regional evaluation prior to field examination. Thirty deposits located in the Kerman Region (Fig. 1) have been studied to identify common features that can be used for exploration purposes, especially for the first stage of regional exploration. A variety of field criteria are available for subsequent rapid field checking prior to trenching and more costly methods such as drilling, etc.Characteristic geomorphic features have been considered as aids in mineral exploration by many authors (e.g., Faniran, 1971; Piotrovski and Lubkashov, 1976; Verstappen, 1983). Clark et al. (1967) indicated the relationship between geomorphology and the supergene enrichment of copper in Atacama Desert, Chile, and correlated three periods of supergene enrichment with three periods of pediment disection. Seeland (1978) used fluvial drainage patterns for uranium and hydrocarbon exploration in the Wind River basin, Wyoming. Postolenko and Konopleva (1973) used the reconstruction of ancient valley systems for exploration of gold placers"

Jan 1, 1996

The Carboniferous sedimentary rocks of southwestern Newfoundland merit investigation because of petroleum, salt and gypsum possibilities and indications of base metallization along the equivalent of the Horton-Windsor con-tact. In this paper, Lower Mississippian (Anguille) strata are divided into three formations: (1) the Cape John below, (2) the Snakes Bight and (3) the Seacliffs. A correlation between these formations and the Craignish, Strathlorne and Ainslie formations of the Horton group? in western Cape Breton Island is suggested. The criteria for the Anguille subdivision are essentially lithological, but preliminary study of included spore assemblages suggests more precise interformational correlations between Anguille and Horton sequences. The re-measured lower portion of the type section of the Codroy group is presented to define more clearly the stratigraphic position of numerous gypsum and limestone beds. Because of rapid facies changes within the Codroy group a simplified two-fold division into upper and lower units is proposed on the grounds of

Jan 1, 1964

By W. E. Oching, M. M. Ghomshei

"Collaboration among Ventilation Engineers, Mine Inspectors, worker representatives, health and safety officers and management is key to an effective operational mine ventilation management. Mine ventilation training, ventilation survey reports for mine stakeholders and interaction with mine frontline workers and management concerning safety, energy saving, assets management and maintenance are effective tools in implementing best industry practices and significant reduction of ventilation operating costs without compromising safety. These approaches may not be new to well established mining companies but the real dilemma is how to implement them effectively and this is what this paper will address.INTRODUCTIONManaging an effective mine ventilation system is becoming increasingly challenging, especially during tough economic times in the mining industry. Management strives for more production while frontline miners work hard to surpass the production targets, thus improving their incentives and above all aiming to enhance the prospects of their job security when the mining industry is facing challenging times. Taking shortcuts by not fully following the safety regulations or industry best practices are often notable, resulting in the rise of Workers Compensation Board claims and temporary shutdowns of active workings, compromising productivity and increasing the operating costs.In accordance with the Mines regulations in various jurisdictions in Canada and the US, it is evident that companies adhere to establishing basic ventilation management systems through the provision of the code of practice, procedures, work practices and standards/guidelines. This is aimed at ensuring the health and safety of underground workers (de Souza, 2017). However, the challenge to many operations is the improper implementation of the mine ventilation regulations including some managers showing reckless disregard for workers safety by focusing on production and not worrying to address ventilation problems (Steven & O'Keefe, 2010). Other challenges facing effective ventilation management include inadequate training of frontline workers on ventilation system and hazards associated with poor ventilation systems such as toxic gases, dust, heat, and underground explosions (Mufson et al., 2010; Suvar et al., 2017); friction between mine managers and the mine inspectors (Mufson et al., 2010), improper maintenance of ventilation system and inventory management, among others."

Jan 1, 2019

By Euler De Souza

"Underground operation ventilation energy requirements constitute a significant portion of mine energy consumption (40–50%) and total energy costs (25–40%). In general, mine ventilation systems are energy inefficient; the author has found several systems that operate at efficiencies below 65%. This paper presents how engineering design principles can improve the performance and efficiency of ventilation appliances, resulting in reduced power consumption and operating costs. Case studies demonstrate that, by retrofitting ventilation appliances using proper engineering concepts, systems will operate at efficiencies well above common operating efficiencies, resulting in a drastic reduction in costs and base electrical and energy loads.RÉSUMÉ Les besoins énergétiques nécessaires à l’aérage d’une exploitation souterraine représentent une part considérable de la consommation d’énergie d’une mine (de 40 à 50 %) ainsi que des coûts totaux liés à l’énergie (de 25 à 40 %). De manière générale, les systèmes d’aérage d’une mine sont loin d’être écoénergétiques ; l’auteur a trouvé plusieurs systèmes fonctionnant à des rendements inférieurs à 65 %. Cet article présente les principes de conception technique qui peuvent améliorer la performance et l’efficacité des systèmes d’aérage, entraînant une réduction de la consommation d’électricité et des coûts d’exploitation. Des études de cas montrent qu’en les rénovant à l’aide de concepts techniques adéquats, les systèmes d’aérage fonctionneront à des rendements bien supérieurs aux rendements habituels d’une exploitation. Ces rénovations donneront lieu à une réduction considérable des coûts ainsi que des charges électriques et énergétiques de base.INTRODUCTIONIncreasing electricity supply problems in North America have encouraged an industry-wide evaluation of energy consumption, resulting in a more urgent emphasis on energy-efficient design and operation for all energy-consuming systems. Electricity is the main mode of energy supply and the mining industry is affected by the increasing cost of this commodity (Natural Resources Canada, 2017). Ventilation systems normally operate 24 hours per day, 365 days per year, and account for 25–40% of the total energy costs and 40–50% of the electrical consumption of a mine operation (De Souza, 2013). Ventilation engineers are under ever-increasing pressure to reduce ventilation energy consumption and be cost effective."

Jan 1, 2018

By R. S. Adhikari

The changes in defects patterns or in element condition index during visual inspection of bridges are primary concerns for inspectors. This paper presents a new approach for change detection of defects in bridges by identifying changes in texture patterns through spectral analysis of digital images. The commonly used method for change detection is image differentiation. This subtraction method requires images to be of same size, scale, and rotation. However, no two images are same in real practices. Thus, image registration is required to align images and to produce change maps. This process is tedious and it is difficult often to achieve a good registered image. But, the change detection task can be readily modeled in frequency domain for texture patterns discrimination and also for quantifying their properties. This paper proposes a novel approach for change detection by transforming digital images into Fourier spectrum. In new coordinate system, 1-D signature functions can be drawn which facilitates easy comparison of textures in different directions. The proposed methodology provides useful tools for comparison of inspection history graphically and quantitatively. In practice, expensive sensors are used to detect subtle change in defect patterns. The proposed method can be used to detect any subtle change in defect patterns using digital images at much lower cost.

Aug 1, 2013

By J. M. Hong, H. K. Zheng, R. Hu, C. B. Zhou

The Jinping-I double curvature arch dam, located in the middle reach of the Yalong River and with a maximum height of 305 m, is the world highest dam of the same type that has been completed. Since the second and third periods of the reservoir impounding, after which the reservoir water level was raised by about 200 m, a significant amount of leakage was observed out of the drainage holes deployed in the lowest drainage tunnel at the left-bank abutment at EL. 1595 m, with a pressure of 0.3 MPa at one typical hole when it was blocked. In this study, a number of analyses including water quality analysis, digital borehole imaging, tunnel geological mapping and in-situ groundwater monitoring were performed to investigate the source of leaking, the leakage passages and the performance of the grouting curtains. An inverse modeling procedure combining the orthogonal design, finite element forward modeling of the transient seepage flow, artificial neural network and genetic algorithm was invoked to further evaluate the permeability of the foundation rocks whose permeability was underestimated in design, using the in-situ measurements of flow rate and piezometric head. The geological structures that lead to the leakage were identified and the seepage flow behaviors in the dam foundation and the left bank abutment were assessed. Given the connectivity nature of the sub-vertically oriented fractures that induce the leakage event, it is found that some of the drainage holes with relative larger amount of discharge could be closed or blocked for reducing the amount of leakage without remarkably increasing the pore water pressure in the foundation rocks.

Jan 1, 2015

By Richard R. Walker, John J. Watkins, Allen C. Amos, Matulich. Angelo

THE KIDD CREEK MINE is located within the Abitibi greenstone belt, near its west end, in an area known as the Porcupine mining camp (Fig. 5). The Abitibi belt, long known for its many major gold and base metal deposits, is the largest Archean (early Precambrian) greenstone belt within the Canadian Shield. In the Porcupine area, the greenstone belt is composed principally of Keewatin (older Archean) basic to intermediate volcanics, with subordinate felsic volcanics developed• locally. Greywacke, mainly of volcanic derivation, occurs associated with and overlying these volcanics. Timiskaming (younger Archean) sediments, principally coarse clastics, unconformably overlie the Keewatin volcanics and sediments. The reader is referred to Goodwin and Ridler (1970) •r. for a more comprehensive description of the Abitibi belt.

Jan 1, 1974

By R. Pandher, R. Schonewille, N. Tripathi

Advanced process modelling tools were developed for the Xstrata Nickel Sudbury Smelter flow sheet using a combination of FACTSAGE TM METSIMTM and ARENATM software. These tools were employed to assist with plant optimisation, emission control, process design, troubleshooting and case studies as applied to the smelter. The development of process modelling tools in pyro-metallurgy commonly involves an in-depth study of the therm o-chemical properties (heat capacity, liquidus temperature, etc.) of all high temperature phases, usually matte and slag. The preferred tool for this purpose is FACTSAGETM, a well-known then-no-chemical modelling software package. The results from the therm o-chemical model have been subsequently incorporated into the development of a process model for the entire smelting facility using the METSIMTM platform. Such process model also includes a number of special features adopted to effectively simulate the complex industrial phases; matte and slag systems. To ensure the robustness and reliability of the process model, several process parameters and assumptions were verified with laboratory and plant data. Consequently, the model includes the ability to examine the impact of a number of plant parameters on potential plant performance. Primary variables are the percent sulphur elimination during concentrate roasting, furnace matte grade and degree of matte metallization. Key output parameters include operating temperature, furnace coke requirement, sulphuric acid production, CO2 emissions and overall energy requirements. Selected outputs from the process model (for example blowing time, slag production rate and matte converting rate) can then be utilised in the development of a discrete event model (DEM) for the smelter using ARENATM software. Incorporation of reliable and validated mass balance parameters enhances the robustness and reliability of the DEM model. The integration of then-no-chemical, process and DEM modeling tools has a distinct advantage in planning plant trials and examining process design initiatives at Xstrata Nickel&apos;s Sudbury Smelter. The present paper discusses the development of these three models and the synergies existing among them. Typical results from all three models are also presented.

Jan 1, 2011

By R. Pandher, R. Schonewille

Advanced process modelling tools were developed for the Xstrata Nickel Sudbury Smelter flow sheet using a combination of FACTSAGETH METSIMTM and ARENATM software. These tools were employed to assist with plant optimisation, emission control, process design, troubleshooting and case studies as applied to the smelter. The development of process modelling tools in pyro-metallurgy commonly involves an in-depth study of the therm o-chemical properties (heat capacity, liquidus temperature, etc.) of all high temperature phases, usually matte and slag. The preferred tool for this purpose is FACTSAGETM, a well-known then-no-chemical modelling software package. The results from the therm o-chemical model have been subsequently incorporated into the development of a process model for the entire smelting facility using the METSIMTM platform. Such process model also includes a number of special features adopted to effectively simulate the complex industrial phases; matte and slag systems. To ensure the robustness and reliability of the process model, several process parameters and assumptions were verified with laboratory and plant data. Consequently, the model includes the ability to examine the impact of a number of plant parameters on potential plant performance. Primary variables are the percent sulphur elimination during concentrate roasting, furnace matte grade and degree of matte metallization. Key output parameters include operating temperature, furnace coke requirement, sulphuric acid production, CO2 emissions and overall energy requirements. Selected outputs from the process model (for example blowing time, slag production rate and matte converting rate) can then be utilised in the development of a discrete event model (DEM) for the smelter using ARENATM software. Incorporation of reliable and validated mass balance parameters enhances the robustness and reliability of the DEM model. The integration of then-no-chemical, process and DEM modeling tools has a distinct advantage in planning plant trials and examining process design initiatives at Xstrata Nickel&apos;s Sudbury Smelter. The present paper discusses the development of these three models and the synergies existing among them. Typical results from all three models are also presented.

Jan 1, 2011

By Nick Vayenas, Ming Cai, Hongbin Zhang Lorrie Fava, Enrique Acuña

"A hybrid methodology is proposed to improve the accuracy of Diesel Particulate Matter (DPM) concentrations simulated in a ventilation network model by using Computational Fluid Dynamics (CFD). DPM, as a primary concern for underground hard-rock mines, has been studied in two dominant numerical models, ventilation network solvers and computational fluid dynamics. Ventilation network solvers are efficient, but they are not able to provide three-dimensional DPM concentration contours and only accept area-average DPM data as input. CFD simulations are time-consuming, but generating DPM concentration results with high accuracy. Besides, both monitoring points and planes can be created in a CFD model, which can take both point data and area-average DPM data as input. The hybrid methodology is intended to combine the advantages of the two by using the CFD results to update the network model results at key locations. A field study was conducted in a dead-end heading in an underground gold mine in the United States. Real-time DPM monitors were used to collect data. A CFD model and a network model were built for the experiment area. The CFD model was calibrated to the experimental data. In the study presented here, results from a calibrated CFD model are converted to equivalent diesel emission rates in the ventilation network model at a shared outlet. The hybrid methodology is used to provide better input for the network model. INTRODUCTION Mine ventilation system is one of the most important parts for an underground mine. It not only provides fresh air to the personnel but also helps clear the contaminants generated from the diesel-powered equipment. For most underground metal and non-metal mines, diesel particulate matter is the main contaminant. It is also the focus of this paper."

Jan 1, 2019

By Marcondes Lima Costa

The Amazon region is characterized by the development of deep chemical weathering represented by widespread lateritic covers and soils. Two distinct periods of laterite formation can be distinguished: mature laterites from the Eocene-Oligocene (and locally from the end of the Cretaceous), and immature laterites from the Pleistocene. The older laterites occur on plateau landscapes,and the younger ones on widespread hilly to ?at lowlands. Both types show complete or truncated pro?les, generally covered by deep yellow to brown topsoils. The mature laterite pro?les contain high concentrations of gibbsite and/or aluminum phosphate, whereas the immature ones are poor in these minerals. The Amazon region is rich in mineral deposits related to lateritic pro?les. Some mineral deposits are of primary origin but were concentrated to economic grades by lateritic processes. The most important ore deposits are of iron, aluminum (bauxite), kaolin, manganese, gold, nickel, copper and phosphate. These are mainly related to mature pro?les. The wide spectrum of ore deposits and mineralogical and geochemical complexity of the Amazon laterites has been promoted by: (1) the prevalence of ideal conditions for laterite formation throughout much of the Tertiary; (2) the presence of varied basement lithologies due to contrasting geological environments; and (3) a variety of epi-genetic alteration types. The lateritic pro?les show a well-developed ore zonation which is related to speci?c lateritic horizons. Iron and gold deposits occur in the ferruginous horizon, which is nearest the surface; the central aluminous horizon hosts bauxites, aluminum phosphate, strontium and gold;and the lower clayey horizon contains deposits of manganese, nickel, copper and kaolin. Resistate phases which residually accumulate throughout entire pro?les include titanium (as ilmenite andanatase), chromium (as chromite), tin (as cassiterite), yttrium (as xenotime), and niobium (mainly asilmenorutile). Epigenetic alteration, caused by swamp environments developed above truncated lateritic pro?les, has led to the formation of high-grade kaolin and refractory bauxites. The laterites inthe Amazon region contain most of all known kinds of ore mineralization related to laterite processes.

Jan 1, 1997

By Marcondes Lima Costa

Abstract-The Amazon region is characterized by the development of deep chemical weathering represented by widespread lateritic covers and soils. Two distinct periods of laterite formation can be distinguished: mature laterites from the Eocene-Oligocene (and locally from the end of the Cretaceous), and immature laterites from the Pleistocene. The older laterites occur on plateau landscapes, and the younger ones on widespread hilly to flat lowlands. Both types show complete or truncated profiles, generally covered by deep yellow to brown topsoils. The mature laterite profiles contain high concentrations of gibbsite and/or aluminum phosphate, whereas the immature ones are poor in these minerals. The Amazon region is rich in mineral deposits related to lateritic profiles. Some mineral deposits are of primary origin but were concentrated to economic grades by lateritic processes. The most important ore deposits are of iron, aluminum (bauxite), kaolin, manganese, gold, nickel, copper and phosphate. These are mainly related to mature profiles. The wide spectrum of ore deposits and mineralogical and geochemical complexity of the Amazon laterites has been promoted by: (1) the prevalence of ideal conditions for laterite formation throughout much of the Tertiary; (2) the presence of varied basement lithologies due to contrasting geological environments; and (3) a variety of epigenetic alteration types. The lateritic profiles show a well-developed ore zonation which is related to specific lateritic horizons. Iron and gold deposits occur in the ferruginous horizon, which is nearest the surface; the central aluminous horizon hosts bauxites, aluminum phosphate, strontium and gold; and the lower clayey horizon contains deposits of manganese, nickel, copper and kaolin. Resistate phases which residually accumulate throughout entire profiles include titanium (as ilmenite and anatase), chromium (as chromite), tin (as cassiterite), yttrium (as xenotime), and niobium (mainly as ilmenorutile). Epigenetic alteration, caused by swamp environments developed above truncated lateritic profiles, has led to the formation of high-grade kaolin and refractory bauxites. The laterites in the Amazon region contain most of all known kinds of ore mineralization related to laterite processes.

Jan 1, 1997

"Developing markets for western metallurgical coal have continued to stimulate considerable exploration activity in the Rocky Mountain foothills and to influence major segments of a wide-ranging carbonization R&D pro-gram. Adjunct studies have included expanded petrographie investigations.Coal preparation has• been principally directed toward utilization of prepared small coal and was, like much of the year's combustion work, strongly influenced by concern over atmospheric pollution. Particular attention has been given to desulphurization and to the suppression of pollutants in combustion systems.In the area of non-fuel utilization of coal, interest has centered on plant nutrients and on a series of coal-based carbons which, inter alia, possess utility as filtration media.Other projects included the development of improved sampling and analytical methods, investigations into the effect of storage on coal proper-ties and R&D in solids pipelining. In addition, a significant volume of basic 'uncommitted' research has been maintained."

Jan 1, 1968

By N. J. Duncan

"Coal mining, whether surface or underground, has hazards that make it unique in the field of industrial safety and health. The often soft, faulted and folded sedimentary strata make wall or roof movement a risk to the safe and economic removal of the coal, while the extraction and handling of coal may create an explosion hazard even in surface operations, In Canada, these problems are compounded by the situation of the coal fields which range from deep undersea deposits in Nova Scotia to steeply pitching thick coal seams high in the Rocky Mountains. Climate too can create its own problems, particularly the effect of metals of minus 40°C temperatures, as crumpled dragline booms at prairie strip mines witness. Because of the difficult and sometimes hazardous conditions, Canada's underground colliery managers, in common with those of other Commonwealth coal-producing countries, must have a government ""certificate of competency"" before being appointed as mine managers. Certification of assistant managers (""under-managers"") and foremen (""fire-bosses"") is also a legal requirement for all of Canada's underground collieries, while the province of Alberta requires certification of surface management personnel. Electricians and mechanics who install and maintain the specially designed equipment underground and in hazardous areas of surface mines and processing plants, and mine surveyors who ensure accuracy of the location of underground workings, must also hold government certificates of competency. The requisites for all certification include a minimum work experience and knowledge of coal mining technology and mine safety and health legislation. Despite recognition of the hazards and increasing knowledge of methods of preventing explosions of flammable gas and coal dust in Canada's underground mines, there have been several disastrous explosions such as those at Springhill Colliery in Nova Scotia in 1891 with the loss of 125 lives, at Hillcrest Colliery in Alberta in 1914 with 189 dead, and more recently · explosions and fires in No. 20 and No. 26 Collieries in Cape Breton. Preventing explosions has required developing optimal ventilation techniques, reducing ignition potential, suppressing ignition at source, draining flammable gas before it can enter the air courses, and preventing, or sealing off, autogenous heatings with their associated carbon monoxide or explosion dangers."

Jan 1, 1985

By Terry A. Lee

The grade of mineral resource estimates underpin all major economic considerations of mining prospects. While there are reporting requirements to satisfy when stating a mineral resource estimate, an examination of NI 43-101 style reports suggests that authors believe that there are a number of ways of addressing these requirements. As a reader of these reports, some processes are helpful and others are not so in getting a real appreciation of how realistic is the mineral resource estimate. Critical to the quality of the mineral resource estimate is how realistic is the economic mineral concentration component. In many cases, this parameter is called grade. The industry experiences increased difficulty in achieving realistic grade estimates as the sample grade variability increases. The level of transparency in a mineral resource estimate is very much a function of the competence of the author. An objective presentation of the critical data, such as grade sampling variability can assist a reader in determining if the geology of the mineral concentration is adequately understood and how realistic is mineral resource grade estimate. This paper has considered 75 NI 43-101 style reports released in the past 2 years. The review demonstrates features that were helpful in determining how realistic the mineral resource grade estimate is. If there is insufficient transparency in a report, there is a high probability that the mineral resource grade estimate will not be realistic.

Apr 1, 2005

By D Maschemeyer

The cobalt production of the Chemical Metallurgical Division of Sherritt Gordon Mines Limited was supplemented, from May, 1962, to June, 1964, by processing 3,500 tons of a calcined cobalt-nickel concentrate. This paper describes the reduction roast -aqueous sulphuric acid leach process and the operating practices employed in recovering cobalt, nickel and copper from this oxidized by-product of a lead-copper operation. Incorporated in this paper is a description of how this process was integrated with the existing ammonia leach -hydrogen reduction process for the recovery of nickel and with the soluble cobaltic ammine process for the recovery of cobalt. Introduction T HE Chemical Metallurgical Division of Sherritt Gordon Mines Limited at Fort Saskatchewan, Alberta, has recently completed ten years of operation utilizing the ammonia leach process for the recovery of nickel, cobalt and copper from sulphide concentrates, matte and other materials amenable to this process. A continuing development program, along with the expansion of certain facilities, has enabled the refinery to attain a production rate of 31, 000,-000 pounds of nickel per year by hydrogen reduction. This represents an increase of approximately 85 per cent over the original design capacity of the plant.

Jan 1, 1965

By I-H. Jung, J. Kim

"Mg alloys are extensively used as light structural materials in modern industry. Mn and RE (rareearth) metals are effectively used as alloying elements to enhance the properties of Mg alloys. Therefore, the thermodynamic database of those alloys is important in the Mg alloy design and processing. Critical evaluation and optimization of all available literature data for the Mn-RE systems were conducted to obtain reliable thermodynamic functions. The Mn-RE systems shows systematic changes in the phase diagrams and thermodynamic properties with increasing atomic number in the lanthanide series. This systematic approach for all RE elements allows to resolve inconsistencies in the available experimental data. INTRODUCTIONRare Earth (RE) metals are widely used in many industrial fields including permanent magnet, electronic materials and structural materials. As a small addition of RE can enhance magnetic, electronic, optical and mechanical properties of numerous materials, the usage of the RE is still expanding regardless of the strategic control of their supply.Magnesium alloys are getting great scientific and industrial attention as the lightest structural materials. One of the drawbacks of Mg alloys is their poor formability at room temperature due to the limited slip system with hcp crystal structure. Recently, several studies (Farzadfar et al., 2011; Sandloebes et al., 2010; Stanford, 2010; Stanford et al., 2008; Yan et al., 2010) show that the additions of small amounts of RE can considerably enhance the ductility of Mg alloys. Therefore, a lot of research on Mg-RE alloys is undergoing to clarify the role of RE on the enhanced deformation mechanism and to find out the most optimum Mg alloy compositions. In order to respond to the need of Mg-RE alloy development, a large thermodynamic database for Mg alloys containing RE has been developed with critical systematic analysis and optimization of the entire RE series data. This includes the thermodynamic database of the Mg-RE (Kang et al., 2009), Mg-RE-RE (Kang et al., 2009), Mg-Al-RE (Jin et al., 2011; Jin et al., 2010), Mg-Zn-RE and Mg-Mn-RE systems."

Jan 1, 2012