Search Documents

By R. E. Jones

"Crusher sizing and application in mining operations is the selection of a crusher or a series of crushers to reduce run of mine ore to a size suitable for either autogenous or conventional grinding. It is important that the crusher or crushers be sized to operate within the range to which they have been designed. By the range to which they have been designed, we mean that the reduction ration must be held between specified limits. Reduction ration is the relationship between feed size to product size.In todays plants reduction is usually accomplished in three stages by primary, secondary and tertiary crushers.Primary crushers are either jaw or gyratory and are designed to handle run of mine feed at an open side setting of 5-1/2” to 7”. Reduction ration should not exceed 7 to 1.Jaw CrushersThe model size of a jaw crusher signifies the feed opening. A model 60 x48 jaw has a feed opening 60” wide by 48” long. The 48” is the dimension between the top of the swing jaw and the top of the stationary jaw. The 60” is the width between the two side frames. The crusher open side setting is the discharge opening at the bottom of the crushing chamber with the jaws in an open position. When corrugated jaw plates are used, the open side setting is measured from tip of one jaw plate to the valley of the opposite jaw plate. If a jaw crusher has a 6” open side setting with a 1” jaw motion, you could also say it has a 5” closed side setting."

Jan 1, 1974

By R. Tipman, T. C. Burnett

"A general computer program has been written to calculate material balances using multiple regression techniques. The program can handle metal assays or size distribution data obtained in multiple surveys of the flotation circuit. The ""best fit"" weight split is calculated between the input and product streams by minimizing the sum of squares of the residual errors using all of the available data. The program includes an assay adjustment feature in which each assay is recalculated to fit the ""best fit"" mass balance. Thus assay or sampling errors can be easily identified. Also the assays can be statistically weighted so the most precise measurements are given the most influence on the material balance. The computer output reports the mass balance, the actual and corrected assays, the percent metal recoveries and the significance and confidence levels for the weight splits.The program enables a rapid and accurate evaluation of mass balances from large masses of data obtained in multiple surveys around a flotation circuit. The effects of changing process variables can be quickly evaluated with statistical confidence."

Jan 1, 1978

By Xie Qiang

It is known that the stress state inside rock discs under Brazilian tests is neither simple compression nor tension, but a complex combination of both stress types, as well as for a beam subjected to bending, where compressive and tensile stresses are separated by the neutral axis. In this study, AE generation was obtained on pure white marbles from south Portugal that were submitted to both Brazilian and bending tests. Main questions to be answered were: (1) Does Kaiser effect exist in tests which create complex distributions of tension and compression? (2) Are there any meaningful differences in AE behavior of marble under Brazilian and bending tests?

May 1, 2009

By Steve McAlister, Colin Sprake

"Enhanced gravity concentration machines have been applied successfully in the following areas of precious metal recovery flowsheets:1. Primary Grinding Circuits2. Shaking Table Tailings3. Pre-Concentration of Leach Feed4. Flotation Concentrates -•, Flash•, ConventionalAlthough great progress has been made, the ability to produce directly smeltable concentrates still remains elusive. Even without this ability, centrifugal concentrators are finding wideningapplications in precious metal concentration:1) PRIMARY GRINDING CIRCUITSEnhanced gravity concentration technology has largely replaced jigging as the technology of choice in precious metal grinding circuits worldwide. The benefits of using a centrifugal field to concentrate both coarse and fine gold are well documented but the placement of these machines within grinding circuits is still evolving. Conventional wisdom dictates that the best location for enhanced gravity machines is cyclone underflow on account of the elevated grade found in this stream when compared to cyclone feed or overflow. Plant operating experience at both large and small scale indicates that there are compelling arguments to place ENHANCED GRAVITY MACHINES on cyclone feed instead. At least two new plants, presently in the detailed design stage will incorporate gravity circuits that treat mill discharge or cyclone feed, Teck Cominco’s Pogo and Newcrest’s Telfer Expansion.Current Conventional PracticeThe current stream of choice for enhanced gravity concentration within grinding circuits is cyclone underflow although recent information indicates a swing toward cyclone feed. Here are some of the arguments for treating a portion of cyclone underflow:"

Jan 1, 2003

By Andy Cole

Barrick Gold recently implemented an oxygen roasting process to treat carbonaceous ore from its Goldstrike property in Nevada. One of the key project challenges was the design of the roaster gas cleaning system, which was driven by the requirements of a strict air permit and the need to achieve very high reliability. The roaster gas systems include multiple stages of wet particulate collection, a dual-alkali SO2 scrubber, mercury scrubbing, CO oxidation and NOx reduction. This paper describes the gas system, the influence of regulations on project implementation, and performance of the system.

May 1, 2002

By Mario E. Rossi

The full economic evaluation of a mining project requires a block model that provides an estimate of the tons and grades of available resources. The model must be representative of the mineralization to be found at the time of mining for specified extraction periods and within acceptable error margins. In an operating mine, there may be a reasonable understanding and estimates of actual dilution and ore loss. This paper discusses the issue from the perspective of a project at a feasibility or preproduction level of development. Three types of dilution are discussed. Internal dilution (or change of support) is function of the spatial distribution of the mineralization and its relation to the operation?s selectivity. Geologic contact dilution is the unavoidable mixture at contacts or boundaries of material with different geologic characteristics, grades, or metallurgical performance. Operational planned and unplanned dilution should also be considered, sometimes incorporated by factoring the resource model, but more accurately by mimicking the grade control process. The resource estimation process always carries uncertainty, which is sometimes significant, and usually caused by several factors. These include quantity and quality of drill hole information; quantity and quality of geologic data; grade estimation methodology; dilution and mining recovery factors applied; etc. A key decision is to whether estimate as accurately as possible the in-situ geologic resource or to estimate the tons and grade of the material to be fed to the processing plant. The geologic modeling and grade estimation methods used are conditioned by this decision.

May 1, 2009

By D. G. Hulbert, J. H. Schubert, R. G. D. Henning

"Froth depth, along with reagent addition and aeration rate, is one of the crucial factors that can be used to control a flotation circuit. Sub-optimal setpoints and disruptions in levels have a severe adverse influence on grades and recoveries. A novel control strategy has been developed which provides exceptionally tight regulation of pulp levels. The controller observes and acts on all the flotation levels simultaneously. This provides a clear improvement over the standard approach, which is to use a set of Pl controllers. The system has been run on several industrial plants and has resulted in reduced fluctuations in level; fast responses to setpoint changes, and fast settling times after start-ups or disturbances. Testwork has shown that the improvements in level stabilisation translate into improvements in recovery and grades.IntroductionProcess control and optimization have an important influence on the economic efficiency of flotation plants. Inefficient operation can allow the wrong balance between grades and recoveries, and can also lead to adverse shifts in the grade-recovery relationship. Of all metallurgical operations, flotation loses the largest proportion of valuable material. Better operation can reduce these losses.An essential requirement of a good controller is that it should be able to stabilize and regulate the plant. Stable operation allows the performance of the plant to be observed without being obscured by the effects of disturbances and fluctuations. The optimum conditions can then be detected more easily. Good regulation can maintain operation at the optimum with proper neutralization of disturbances. Only when good stabilization and regulation are achieved can an optimizing strategy be properly applied.Froth depth, aeration rate and reagent addition are the three means by which a flotation plant is generally controlled. These control actions are effective on different time scales. Reagent addition is slower in its effect as some conditioning time is required. Since reagents are only added at the head of the circuit and at a few selected points within the banks, time is required for the effect of reagent changes to move through the circuit. Because of this slower time constant, reagent addition is more suited to process optimization and to dealing with slower changes in the process. An example of these slower changes is variation in the feed."

Jan 1, 1995

By Svato Prochazka

Content: ? commonly used drive systems ? drive system efficiency ? introduction to SR technology ? SR drive system advantages Commonly Used Feeder Drives Technologies ? VFD + induction motor ? hydraulic drive + hydraulic motor SR drive + SR motor

May 1, 2010

By T. Yalcin

"This paper describes the development of a mathematical model for determining the liberation of an ore at various grinding sizes, based on the combined results of microscopic counting, grinding tests, and chemical analysis.The method is illustrated with an application to the magnetite ore of Sherman Mine in Temagomi, Ontario. For this ore, a degree of liberation of 98.7% was determined at a grinding size of 90% passing 44 microns, which closely corresponds to the final grinding size employed at the Sherman Mine Concentrator.Introduction Liberation characteristic of ores have direct and significant bearing on overall economics of concentration processes.Target grades and recoveries can be achieved only it minerals are adequately liberated prior to separation. Degree of liberation depends on the extent of size reduction. However, due to the high costs associated with size reduction processes, it is important to keep size reductions within limits of satisfactory liberation. Prevention of excessive size reduction is also necessary because of inefficient mineral separations in very fine sizes. Hence, a study of reduction size — liberation relationship is essential for optimum profit from milling operations.A number of procedures have been developed for liberation studies (1-12), but there is lack of method for universal adoption.A new approach is presented in this paper that might provide a realistic estimate of liberation and give a practical guidance as to the degree of size reduction required for satisfactory liberation."

Jan 1, 1985

By Cecilia Arrue, Dominic Fragomeni, N. O. Lotter

"A statistically designed benchmark mill survey was carried out in July 2005 at the Kidd Creek Concentrator, D Division circuit, which processes Ni/Cu ore from the Montcalm deposit. A structured statistical survey approach was followed, together with defined quality controls, which would assign a 95 percent level of confidence in the result.A set of six surveys were completed over a limited time; the corresponding stream samples of the surveys found acceptable were combined to obtain high confidence composite samples. The head grade of each survey is compared to two distributions to test its acceptability; surveys that fail to conform to these trials are rejected. The accepted set of surveys, which is a robust representation of the process, is prepared into a composite for QEM-SEM analysis and mass balance purposes.Where the above practice is a standard procedure in Falconbridge for QEM*SEM purposes, in this case each individual two-hour survey unit was measured and analysed for a mass and value balance. It is shown that none of the individual mass and value balances close as well as the composite set of accepted two-hour survey units. This founding is in keeping with the averaging properties of the Central Limit Theorem.INTRODUCTIONMontcalm OperationsNi/Cu bearing ore from the Montcalm deposit is being processed at the Falconbridge, Kidd Creek Concentrator in a modified D Division circuit. The circuit was commissioned in the fall of 2004. Ore is crushed at the minesite to –19 mm and trucked to Kidd for delivey into the 4 parallel fine ore bins.Ore is milled in a rod mill followed by cyclones and 2 parallel ball mills. The grinding circuit treats Montcalm ore at an average feed rate of 100 wet tonnes/hour (750,000 tonnes/annum) and produces a flotation feed particle size of 83% -53 um. A simple flowsheet including bulk Cu/Ni roughing and 2 bulk cleaning stages followed by Cu/Ni separation in 2 stages is practiced. Soda ash is used as a pH modifier in bulk flotation. SIBX is the collector. Lime and Dextrin are added into Cu/Ni separation for the depression of pentlandite."

Jan 1, 2007

By Ralph Harris, Xia Qi, Frank Komsic

"Gold cyanidation kinetics which are often limited in commercial operations by the rate of oxygen dissolution from gas bubbles into the slurry, are discussed. Emerging technologies for improving the rate of oxygen dissolution are compared and the gas efficiency, energy use and operating performance of inverted cones and a device based on a jet diffuser are examined. The effect of solids loading is also reviewed and a relationship between operating parameters and the kilograms oxygen dissolved per kilowatt-hour is presented.Inverted cones are shown to create slurry settling problems at high gas flow rates and surface tension lowering agents are shown not to greatly improve the overall rates of oxygen dissolution.The novel jet diffuser technology operates at a range of gas to liquid ratios that improves its energy use over conventional technology and the performance of a number of designs are discussed.Gas efficiencies as high as 35% were observed with the novel diffusers at 40 cm diffuser immersion and are expected to increase at greater immersions. Energy use of 1.8 kg 02 I kWh were estimated for prototype full size diffusers operating at 100 cm immersion. Energy use of 3.S kg 02 /kWh is conservatively expected at 600 cm immersion.IntroductionGold ExtractionGold that can not be recovered by gravity separation can be recovered by either the Merrill-Crow process or the newer carbon in pulp (CIP) or carbon in leach (CIL) processes 1. Reductions in operating costs and improvements in gold recovery are central mill operating strategies. The present paper examines the potential for improvement that can be achieved in the gold cyanidation step of gold recovery. This paper introduces a number of emerging technologies and provides a basis for comparison of the performance. It shows that the basis for comparison of a particular technology depends on the type of gold extraction circuit employed and the type of reactants employed."

Jan 1, 1996

By G. Taylor

"The Iron Ore Company Of Canada's Carol Project is located in Labrador City, Newfoundland. Labrador City is some 912 air kilometers northeast of Montreal, and 417 ratl kilometers north of Sept-Iles, Quebec.Over 2,800 employees work at the Carol Project to produce some 20.0 million tonnes of concentrate and 10.5 million tonnes of pellets annually.In 1979 our Training Department started to develop the DACUM System of training for our Concentrator Operations Department.DACUM is an individualized, self-learning, training program. It is both a curriculum plan and an evaluation instrument.To date, the DACUM System has been completed for all occupations in the concentrator and work will commence shortly to develop DACUM for our Pellet Plant and Mine Operations Departments."

Jan 1, 1982

By Jean-François Dorion

La corrosivité des environnements miniers souterrains est un phénomène peu étudié au Canada. En plus de détériorer les systèmes de soutènement, la corrosion s?attaque aussi à divers installations et équipements souterrains. Cette étude, débutée en janvier 2007, est l?établissement d?une banque de données afin de caractériser les environnements miniers souterrains selon leur potentiel de corrosivité pour les systèmes de support de terrains. Pour ce faire, cinq (5) mines ont été sélectionnées afin de comparer les environnements : Laronde, Géant-Dormant, Niobec, Mouska et Doyon. À chacune des mines, trois (3) endroits ont été étudiés. Les résultats préliminaires démontrent une grande variabilité des conditions d?une mine à l?autre ainsi qu?à l?intérieur même d?une mine. La minéralogie des roches et du gisement influence la composition des eaux souterraines et la présence des sulfures joue un rôle important sur l?agressivité de l?eau et de l?air des mines de l?étude. Afin de déterminer le potentiel de corrosivité, plusieurs paramètres doivent être considérés et la mine doit être zonée selon l?agressivité des endroits.

Feb 1, 2008

By A. Akerman, C. P. O’Connor, N. Vayenas

"Stereolithography is a well-known rapid prototyping technique in the manufacturing sector. Essentially, it is a three-dimensional printing process that produces plastic prototype parts from standard CAD files. At present, Canadian mining companies are not fully aware of the potential of rapid prototyping techniques (RPTs) for their production and mine design systems. Mining engineers and geologists attempt to visualize and understand the characteristics and layouts of orebodies on computer models, and in cases where it is decided to develop physical models, the process is time-consuming, based on simplified constructions. RPTs, such as stereolithography, can facilitate engineers and geologists to quickly, and with satisfactory accuracy, visualize sections of orebodies and evaluate alternative ore extraction techniques using 3D solid models.The research discussed in this paper is carried out by the Laurentian University Mining Automation Laboratory (LUMAL) in collaboration with Inco Limited and the Integrated Manufacturing Technologies Institute (IMTI) of the National Research Council of Canada. The main objective with this research is to evaluate the applicability of state-of-the-art RPTs to underground hard rock mining systems. RPTs can play a significant role in accelerating the design and development process of mining systems."

Jan 1, 2006

By Steve Wilkinson

"""Techniques for coarse-particle beneficiation of some gold ores and methods for determining potential for sorting any gold ore deposit.""With the advent of high speed computers, laser technology end different types of electronic sensing devices, ore sorting machinery has been developed, capable of handling significant tonnage rates while maintaining high level efficiency. Gold ores may be amenable to coarse-particle beneficiation where there exist measurable criteria upon which there can be recognition of auriferous versus barren lumps in the run of mine. Three types of criteria are suitable for sorting and are:i) Photometric - optical variance between ore and waste such as vein ores hosted by barren country rock;ii) Conductivity/Magnetic - based upon the metallic mineral content of ore end waste, and its association with Au, such as found in sulphide/arsenide Au ores,iii) Radtometric - detection of natural gamma activity occurring with uranium-bearirig gold ores.The method for determining the sortability of an ore depositconsists of, at least, three stages:i) Initial stage identification of ore and waste types,mineralogical/petrographical associations,amount of dilution in P.O.M.establishment of any sorting criteria]"

Jan 1, 1985

By Patrick F. R. Murphy

The mechanization of platinum group metal (PGM) underground reef mining in South Africa has posed a challenge to mining engineers for several decades. This is primarily due to the shallow dip angles and narrow thickness (<1.1m) of the tabular orebodies mined, and the issues faced in developing reliable drilling, bolting and loading machines suitable for such hard-rock mining applications. Presently, mining is typically conducted using hand drills and scraper shovels. These methods, however, are intensive in terms of manual labor, and limited in terms of productivity, and improved methods are desired. This paper will review the technical features of a 4 tonne, low-profile, LHD for narrow-reef PGM mining, developed by EJC Loaders Division.

May 1, 2003

By M. Massinaei, S. Abasi, M. Oliazadeh

Reliable measurement and control of the pulp-froth interface (froth depth) in the flotation columns is critical to achieve the desired metallurgical performance. Shallow froths result in a reduction of grade because of particle entrainment and deep froths reduce recovery because of the drop back of entrained and weak hydrophobic particles to the pulp zone. The cleaner circuit at Miduk copper concentrator consists of three parallel MicrocelTM flotation columns 4 m in diameter and 12 m in height. The interface level of the flotation columns is measured by two pressure sensors located at 1.4 and 2.4 m from the cell lip (in the collection zone). In this study the performance of the level detection system at different operating conditions was evaluated. A calibrated float-ultrasonic location system was used for measuring the actual froth depth. The results indicated that the existing level control system was subject to considerable error. The absolute error was found to be 33.27 cm. This was mainly attributed to the constant set-point value assigned to the froth density (ρf=0.3 g/cm3), which actually varies with the operating conditions. The actual froth density at different conditions was calculated and its average value (ρf=0.12 g/cm3) was re-set in the control system. This resulted in substantial reduction in the level-detecting error. Recommendations for more accurate measurement of the interface level were presented. INTRODUCTION Froth flotation is a complicated process because of many involved variables. One of the most significant controlled variables in the flotation process is the pulp-froth interface (froth depth). The froth depth has a profound influence on the metallurgical performance parameters (i.e. grade and recovery). Shallow froths result in grade reduction because of particle entrainment and deep froths reduce recovery resulted from the drop back of entrained and weak hydrophobic particles to the pulp zone (Finch and Dobby, 1990). Various techniques have been developed for measuring the interface level of the flotation cells in the last few decades. These techniques can be classified as: Techniques based on hydrostatic pressure measurements (Finch & Dobby, 1990), Techniques based on the density gradient (float) (Moys & Finch, 1988), Techniques based on conductivity measurements (Uribe-Salas, 1991), Techniques based on temperature measurements (Moys & Finch, 1989).

Jan 1, 2019

By H. Wyslouzil

"The Kelsey Centrifugal Jig is a gravity separation device which utilizes the principles of the conventional mineral jigs but with the additional feature of being able to vary the apparent gravitational field. This is accomplished by utilizing the specific induced movements of the conventional jig within a centrifuge.Pilot plant trials have been underway since July 1988 to evaluate the potential applicability of this technology to various process streams at Rio Kemptville Tin.The grade/recovery relationships for samples treated in the jig were consistently better than results obtained from tables. Recoveries of more than 90% were attained at concentrating factors ranging up to 20. When compared with electrostatic separators, the jig achieved equivalent metallurgical results in a two stage process, without the expensive requirement of filtration and drying. Recoveries exceeding 96% were achieved with final concentrate grades averaging higher than 60% tin.INTRODUCTIONMineral jigs have been used for hundreds of years. Many different types have been developed, and each one has numerous variations. In recent years, the idea of applying centrifugal forces to conventional jigs has been put to practical tests and today a number of units are in commercial production. In principle, by enhancing the apparent gravitational field, it should be possible to recover finer particles by overcoming viscosity and surface effects which tend to limit existing gravity devices. In addition, it may be possible to use gravity to separate minerals with much smaller specific gravity differences."

Jan 1, 1990

By Bryan A. Bartley

"Jim Macdonald was promoted from Waterworks Engineer to Streetworks Engineer for the Wellington City Council. He thus took over the City quarry and responsibility for its performance. The crushing plant needed upgrading and he thought it would not be difficult to make a crusher to overcome a problem. If he had a longer association with the quarry industry he would have used conventional methods and equipment, so his invention arose from a fresh view of crushing.He invented the Barmac Rotopactor after observing a wear resistant chute with a lining of dead stone trapped above a piece of angle. This idea led to a rotor lined with trapped stone, rotating on a vertical spindle. In trying - a model rotor he observed the impact against a circular rill of stone in half an oil drum and thus was started a very fertile new area of developement in comminution. The writer helped in the developement and shares in the patents. Jim died in January 1982, just as the machine was becoming known and some 200 were in use in various countries. Most were working in hard rock quarries et that time but recent uses have carried the machine into the mining and mineral processing field. This paper is directed at that industry."

Jan 1, 1985

By Derek J. Cyr

Climate has an immense impact on the properties of Athabasca oil sands and the ease or difficulty with which it is excavated and extracted. During the winter months, exposed oil sands surfaces freeze. When hydraulic and electric shovels used in the various operations in the Fort McMurray area excavate the benches, large frozen lumps are created. These lumps are either destined for a lump dump where increased costs are incurred due to rehandle, or they are sent to the primary crushers where they can cause significant downtimes by jamming the crusher. The crusher down time can sometimes be in the order of hours of lost production. Studies on data from two consecutive winters at Syncrude Canada?s North Mine show a high correlation between climate and the generation of frozen oil sands lumps. Temperature, ground cover, traffic, bench exposure time, oil sands grade and moisture content all contribute to this problem. A 1D frost penetration model was used to predict the depth of frost expected in oil sands and the corresponding likelihood of frozen oil sands lumps. To combat the challenge of frozen lump generation, a number of proactive and reactive measures can be taken: artificial snow, shallow ponds, scheduling, blasting or ripping.

May 1, 2004