Search Documents

By S Wasi, J Tobiczyk, J Roszkowski

Methane and fire hazards have a vital effect on work safety and continuity of mining plant operation. In the 1990s, the SMP hazards monitoring and ventilation control systems, based on continuous measurement of air parameters, were put into operation at nearly 30 Polish mines. These systems provide continuous measurement of methane concentration within the range of zero to 100 per cent with automatic switching off of electrical energy immediately after detection of potentially explosive conditions. Early detection of coal spontaneous combustion and open fires is made by continuous measurements of CO, CO2, smoke and O2 content in mine air as well as temperature changes in air and rock mass. The essence of the system is intrinsic safety of all underground instrumentation and uninterrupted central power supply from the surface. All abnormal and critical states are signalled to the mine control room. These trigger alarm and emergency procedures. The computer based ventilation monitoring and control system also performs the function of an expert system for fire detection and underground fire fighting. The mine control operator (dispatcher) makes use of stored data in computer escape route schemes and procedures for the safe withdrawal of miners from hazardous areas. The operator can put in motion intrinsically safe alarm signalling units and banners with programmed messages indicating escape routes.

Jan 1, 2005

By Davey P. T, Tsambourakis G

Mineralogical analysis of supergene sulphide ore recovered from areas close to the underground workings at the abandoned Mutooroo (South Australia) mine shows that the original sulphide minerals have undergone substantial alteration. The cause of this alteration is believed to be contact with the highly saline, acidic mine water. The copper is now present as a sulphide that can best be described as a copper- and iron-delicient chalcopyrite, CuxFeyS2, where in most cases x < y. The values of x and y vary from point-to-point within each grain.Leach tests under a variety of conditions show that dissolution of the copper from the supergene sulphide ore can be readily achieved, particularly when compared with the behaviour of Mt Isa chalcopyrite concentrate. For the supergene sulphide ore, an increase in the acidity and the iron(lll) concentration of the leachant re ults in an increase in the rate of copper dissolution.The results are briefly discussed in terms of the experimental in-situ leaching operation at Mutooroo, South Australia.

Jan 1, 1986

The design and selection of components for belt conveyors is a well known procedure and many handbooks, catalogues and design manuals offer a wide range of detailed information which can be applied to most of the known conveyor problems. The aim of this paper, however, is to investigate the various methods of conveyor drive configurations, and incorporate the latest technical achievements in the control systems, particularly for high capacity conveyor systems carrying ore from pit to processing plants where the lowest maintenance, operating and initial costs are of major importance. Past experience has proven that multi pulley drives can reduce initial capital cost of a conveyor; this leads to the need for better torque control during startup, running, stopping and load sharing. Many methods of torque control are available and have been used in the past. All types have their advantages and disadvantages and must be considered when designing a conveyor or conveyor system. However the recently developed solid state electronic soft start controls utilising AC squirrel cage induction motors are gaining acceptance, especially for a conveyor system where the same control and logic system can be used to transmit startup commands to more than one

Jan 1, 1978

YOUR Excellency, Fellow Members of the Australasian Institute Of Mining Engineers and Gentlemen:- Nearly a decade has passed, since our Institute first met in New Zealand. May I, at the very outset of this second gathering, congratulate the Institute on the great progress that has been made in the interval. At the first meeting in New Zealand in the year 1903, I understand that less than 20 persons were present, and now in the large concourse before me I believe there are not fewer than 140 persons, while if every member of the Institute to-day where here there would be over 500 which is a great change from a membership of only 250 in 1903. I feel deeply appreciative of the honour you have conferred upon me by electing me your President for the year 1911. In return for the compliment, may I ask you to believe that I shall do everything in my power to further the interests of the Institute throughout the coming year.It is a great regret to me to realise that soon my work in New Zealand will be over. However, I trust that the new...

Jan 1, 1911

In recent years a large amount of work has been done at various plants overseas, and also at Broken Hill Associated Smelters, Port Pirie, South Australia, on the use of Dwight Lloyd sintering plant gases for sulphuric acid manufacture by the contact process.Several plants have modified their sintering machines and operating procedure, and some have adopted gas recirculation techniques, to obtain a relatively high proportion of the sintering plant gas at an S02 concentration acceptable to a contact acid plant 1.These adaptations were investigated at Port Pirie, and it was found that gases of suitable S02 concentration could be obtained. The results justified installation of a contact acid plant and a decision was accordingly made in 1949 to construct such a plant.However, the local conditions presented some difficulties not generally encountered at other plants, the chief differences being:a. For maintenance of production of 98% H2S04 , an unusually high S02 concentration is required, because of the prevailing high temperature 'of the purification train cooling water.b. The entire sintering operation is conducted on two large machines, 55ft. x 10ft., operating in series as "First" and "Second over" machines (a two-pass roast.) Any interruption" to either machine causes a complete interruption of plant operation and gas flow.

Jan 1, 1951

The title of my address today 'An Environment for Mineral Development' is a play on words, but I wish to use the meaning of the word environment in the broadest possible context to comment on those factors that control mineral development in New Zealand today. Of prime importance, let us consider the current economic environment in which New Zealanders live and work, as individuals and communities, and as a trading nation. It is the expanding growth requirements of the emerging nations and the interactive economic forces of our international trading partners and competitors, that dictates New Zealand's economic environment and thus the priority to develop its natural resources. As an itinerant New Zealander who has kept a watching brief over the economic environment in New Zealand over the last 30 years, I say, without prejudice, that I am concerned to have seen New Zealand's external and internal trading position deteriorate so rapidly in the last decade. I am concerned that a significant proportion of the population has been extremely slow to realize that with the creation of the European Economic Community, in the late 1950s, and following the first OPEC oil crisis in 1973, New Zealand in a corporate sense came close to technical bankruptcy.

Jan 1, 1985

By Botz R. W

Macroscopic and microscopic studies of the outburst-prone Gemini Coal (Bowen Basin) showed that outbursts were associated with a localized inertinite-rich ply. Previous studies of the Gemini Coal had shown a general relationship between desorption rate, regarded as a good measure of outburst proneness, and inertinite content of coal samples.Desorption rates increased with increasing inertinite content and were highest for inertodetrinite-rich samples. These results suggest that inertinite content and composition play a significant role in outbursting and may be useful in identifying outburst-prone coals, which could be confirmed by desorption measurements.Consequently outburst-prone areas in the Upper Permian coal measures ofthe Sydney, Gunnedah and Bowen Basins have been defined using a combination ofthe parameters, inertinite content, depth ofcover and coal rank. In the Upper Permian, inertinite-rich coals are confined mainly to the top of the coal measures, except in the Sydney and Gunnedah Basins where an inertinite-rich interval (Bayswater Coal and correlatives) is also present towards the base of these measures. Only a small area ofthe central Sydney Basin, butmuch ofthe north-eastern and north-central part of the exposed Bowen Basin is considered outburst prone on the basis of these parameters.The most outburst-prone inertodetrinite-rich lithologies have a patchy and unpredictable distribution in the top of the Upper Permian coal measures. They can be defined only by sampling and petrographic analysis at the subsection level.

Jan 1, 1986

Pyrite is one of the principal Au-bearing minerals in refractory gold ores. Significantly high Au concentrations of up to 5200 ppm are present in pyrite. Pyrite hosting high levels of Au is also enriched in As. Pyrite as an unwanted mineral ends up in wastes and constitutes one of the primary sources of As in the mining and metallurgical wastes. Arsenic can be readily released to the environment due to rapid oxidative dissolution of the host pyrite under atmospheric conditions. In order to determine the form and occurrence of arsenic in pyrite, micro-X-ray absorption fine-structure spectroscopy (XAFS) spectra were collected from a range of arsenical pyrite grains having different morphologies and a range of arsenic and gold concentrations. All the pyrite grains are characterised by the dominant edge aligned with As-1 valence state. In pyrite, arsenic atoms substitute for S atoms that are in six-fold coordination about each Fe atom. XAFS data suggest that As atoms occur in clusters within the pyrite structure. In addition to As-1, fine-grained, inclusion-rich and framboidal-type pyrite grains have a second As species at ~11 875 eV corresponding to As5+. This As5+ species in pyrite is highly variable and attributed to the oxidation of arsenic exposed on the surfaces of pyrite.

Jan 1, 2008

By Boyce WH

Earthquakes are the most frightening and devastating natural phenomena known to mankind. They strike without warning and their consequences can be disastrous in terms of the toll of human life, financial crises related to the damage or destruction of man-made structures and the social and economic effects on a wide spectrum of the affected communities in the aftermath of the event. Such situations can be widely attested to by most areas around the Pacific Rim. Indeed, the threat of earthquakes is always imminent because of the geological-tectonic nature of the region as manifested by past experiences. It is patently obvious that earthquake occurrences are not only a geological hazard but also pose a serious social danger. When one considers the 19 September 1985 Mexico (Michoacan) earthquake (Mitchell at al., 1986), the necessity of continuing research is of paramount importance. An estimation . of earthquake risk encompasses both qualitative and quantitative aspects and demands a multidisciplinary research effort integrating seismology, tectonics, geology, enginering, sociology, economics, insurance and governmental policies (Bolt, 1978; Booth, 1984). These roles in mitigating such a hazard have been aptly discussed by Press (1985). A series of discussion papers based on an intergovernmental conference covering the whole scenario were published by UNESCO (1978). A comprehensive case history was provided through a workshop on the 1886

Jan 1, 1987

By W Pytel

A special model of vertically loaded pillar behaviour is introduced to the general, multi-plate based, floor-pillar-roof system interaction analogue. This permitted analysing room-and-pillar mine systems in any geological conditions, including the effect of pillar elastic-plastic behaviour with strain softening. In the model, pillar instability is one of the important phenomenon, which may be expected to occur, and which the operator has to be prepared for. Thus the entire systemÆs safety is determined mainly by strong roof strata behaviour and therefore they have to be examined in actual stress-strain conditions utilising the appropriate strength theories. It was assumed that the so-called safety margin, representing the relation between load intensity and material strength, might serve as the basic indicator of possible roof instability development. Therefore, the safety margin may be estimated by comparing the actually computed components of stress-strain tensor with ultimate values characteristic for a given material determined in laboratory. In order to illustrate the effect of technological pillar size on roof strata stability, two different mining systems (methods of mining) in one of the æPolkowice-SieroszowiceÆ Mine districts was modelled using the finite element method formulated in three dimensions, assuming different materials within different rock mass strata, as well as a number of horizontal planes of discontinuity within the model.

Jan 1, 2003

The mineral resource that a mining company has access to, represents the majority of the embedded value that exists within the company, as well as the competitive advantage that the company has over its peers. However, the real value is only realised once effective mining plans have been put in place, which optimise the extraction of the resource, and add measurable value to the company. The concept of mineral resource management (MRM) has been developed in South Africa, to ensure this optimisation happens in an integrated and quantifiable manner, such that value is added and risk is reduced, resulting in bottom line improvement for the stakeholders of the business. This paper describes the process of mineral resource management, and draws on successes and failures of various companies, to illustrate how it should be implemented, and what measures should be put in place to ensure its success. This requires a fundamental re-appraisal of the way in which mining companies plan and execute their businesses, and focuses attention on real value adding activities and behaviour through the use of economic value added as an appropriate metric by which to measure real value and risk. Specifically, the paper focuses on these aspects as applied to planning models and processes, exploration activity and risk management, to ensure operational and project success.

Jan 1, 2006

By C P. Kramers

The need to provide a sufficient quality and quantity of backfill continues to increase in South Africa, particularly as related to the increasing depth of mining. More and more applications require well designed fill systems either as classified or cemented backfill, and in some applications even tailings/aggregate based backfills. The paper discusses developments in backfill technology in South Africa with special emphasis on reliable system designs and operations, particularly as related to the preparation and hydraulic transportation aspects. Approaches for the alleviation of previous problems associated with premature pipe failures in vertical shaft columns for the distribution of tailings based backfills are discussed. Resulting from CSIRÆs developmental work, reliable full-flow systems, which can operate at low system pressures, have become a common practice, provided that backfill flowrates and internal pipe sizes are well matched. This aspect is reviewed. With regard to the tailings/aggregate based backfills the paper reviews some of the results of comprehensive in situ monitoring and the development of such systems. It is shown that a thorough understanding of the effects of aggregate top size, fines content and slurry relative density is required in order to ensure the restartability of temporarily shut-down pipelines. Some innovative technologies for the comminution of development waste underground to yield aggregate products potentially suitable or hydraulic transportation and backfilling, are briefly discussed.

Jan 1, 1998

By Barria J, Mencho J, Gonzalez GD

An extended Kalman Filter is used to build an on-line estimator of total ore, fine ore and water hold-ups in a SAG mill. In addition, an equivalent grinding rate from coarse to fine ore, as well as the discharge rates of solids (fines) and water are also estimated as part of the adaptation procedure of the model used for the Kalman Filter. The measurements used in the Kalman Filter estimator are the total mill weight provided by load cells, and inferred discharge flows of fines and water from flow and density measurements performed downstream. The net ore and water feed to the SAG mill are used as inputs to the estimator, and also the proportion of fine ore in the feed. As an example of how to introduce robustness in the estimation in the face of sensor bias errors, an estimation of the load cell bias error is introduced in the estimator, thus providing self calibration. The estimator presented in this paper has been tested by simulation using a detailed SAG mill mechanistic dynamic model comprising 27 size fractions well fitted to a pilot mill. The maximum error in the estimation of the operational variables - total and fine ore as well as the mill contents under different operating conditions - is about ten per cent.

Jan 1, 1993

After the minim operation, most raw materials that occur in the earth's crust require some form of processing or refining before they can be converted into a final end product. In the mineral industry these remarks apply to materials such as iron ore, bauxite, limestone, copper ore and many others that are found in Australia in large quantities. Processing plants for these raw materials operate more efficiently, however, if the feed to them is consistent in both physical and chemical characteristics. Such uniformity rarely occurs in nature so that some form of homogenisation, or blending, is required ahead of the processing plant. Bending also assists the mining operation itself by reducing; the need for selective mining and, by combining high and low grade materials, a more uniformly graded, commercially acceptable product can be obtained, thereby increasing the commercial life of a mine or quarry. Bed blending is the most efficient of the processes available, and following its development in the United States in 1905, over 100 plants have been installed, or are under construction, all over the world. The original process, the Robins--Nessiter system, has been the subject of continued improvements and refinements, so that economical capacities are possible from less than 100 l.t.p.h. up to 10,000 l.t.p,h. and beyond.

Jan 1, 1969

By T G. Measham, D A. Fleming

When attempting to understand potential regional or community socio-economic changes that resource-extraction industries may produce, it is important to analyse the channels that promote these changes. In this study, we propose a conceptual framework to better understand how socio-economic effects are likely to emerge in regions impacted by mining. The framework considers three levels of hierarchical effects (Measham, Fleming and Schandl, 2016).In the first level, the resource-extraction industry causes four direct initial impacts on nearby communities: labour demand shock (mining employment generation), income generation (compensation to landowners and higher wages), environmental consequences and land tenure/Aboriginal issues and an increase in local tax revenues.The second level is shaped by the subsequent population increase (given by immigration of permanent or temporary residents) produced by the new levels of employment and income that resource windfalls can generate in resource-extraction regions. These increases in employment, income and population become the source for a rise in the demand for local (and non-local) goods and services.Finally, the third level is given by boomtown-like and other socio-economic effects generated from the initial effects.CITATION:Measham, T G and Fleming, D A, 2016. A conceptual framework to understand the local community/social impacts of mining, in Proceedings Life-of-Mine 2016 Conference , pp 188–190 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By G Solly, P J. Leevers

Day-to-day operating practices at existing operations need provide high quality data for decisions that will impact directly on the potential value of the available resource, in addition to meeting standards of quality expected of data used in feasibility studies that will be completed to obtain additional capital required to finance operational improvements. Drill hole location, down hole survey and assay data standards of accuracy and precision have received considerable attention in recent years. The authors propose that geological descriptions of both cored and non-cored drilling warrant at least equal attention, considering their fundamental role in establishing the framework used for geological modeling and resource estimation. The iron ore deposits of the Middleback Ranges have been a major source of iron ore for almost a century. High-grade hematite-dominant ore is currently mined by OneSteel from three open pit operations supplying ore to the companyÆs integrated steelworks at Whyalla. A review of OneSteelÆs future iron ore resources, commenced in 2002, highlighted the need for more flexible and comprehensive management of all forms of geological data used in resource evaluation. Driving this program was the information needs of feasibility studies of the Iron Magnet deposit, located beneath the existing Iron Duke and Iron Duchess mines. Prior to the beginning of 2003, resource evaluation drilling data collected by OneSteel was managed using an in-house system based on industry standard relational database software. The system was demonstrably effective in ensuring the fundamental integrity of basic drilling data, but lacked necessary capabilities for the acquisition and management of geological descriptions, geotechnical and geophysical data obtained by down-hole logging. OneSteelÆs existing system for the management and interpretation of geological descriptions was restricted to storage of a single three digit code for each lithological description interval. The original logs for a large number of older drill holes could not be located, having been either poorly archived or culled from the database in the belief that they did not contribute to the understanding of the resources currently being mined. The three digit codes represented a combination of lithological and stratigraphic descriptions, including many subtle variations in iron ore colour and texture believed to be associated with variations in geochemistry, but subsequently demonstrated to be either incorrect or inconsistently applied. This resulted in the establishment of a plethora of codes for a relatively small number of distinct lithologies. Improvements implemented by OneSteel geologists addressed these shortcomings by ensuring the new data management system: facilitated the objective description of lithological characteristics; distinguished between obsevations and interpretations (eg lithology versus stratigraphy); promoted consistency between descriptions provided by different geologists; and helped to ensure data integrity by developing an audit trail for alterations made to data subsequent to its acquisition. The data used to develop interpretations of mineralisation distribution and characteristics are fundamental to the effective utilisation of a mineral resource: any mineÆs most important asset. Resource related risk is widely recognised as the principal source of technical risks affecting resource development projects, whether they are new mines or expansions of existing operations. A key lesson from this work is that most commercial or æin-houseÆ developed geological data management systems are able to handle basic data validation tasks effectively. Geologists, however, need to ensure that the data management system is appropriately structured to help promote the acquisition of objective and consistent data for interpretation.

Jan 1, 2003

By Graham JW, Cullen GV

edicted increase in, Aluminium production and the possibility of a diminishing supply of petroleum coke for anode electrodes in alumina reduction cells makes it desirable to find alternative electrode materials. Brown coal char, with a lower ash content and with an elemental purity similar to petroleum coke, has been produced by leaching in hydrochloric acid, washing with water and charring at 115000. The cost of processing is estimated to be competitive with petroleum coke. Without further processing the bulk density and real density were undesirably low, but. by briquetting the coal before charring and crushing, the bulk density was improved to 92 per cent of the petroleum coke value and the Particle density was improved to 92 per cent of the density of petroleum coke by water-displacement or 75 per cent by mercury displacement. Pre-baked electrodes were prepared from the char alone, mixtures of petroleum coke and char and from petroleum coke alone, all bonded with coal tar pitch. The electrodes were tested for the usual physical properties and were, evaluated for performance in a laboratory size alumina reduction cell. Electrodes based on brown coal char alone were found to be inferior in physical properties, and performance, but mixtures of the char and petroleum coke, despite poorer density, electrical resistivity and carbon consumption on a theoretical basis, in performance tests gave up to 17 per cent better carbon consumption per weight of aluminium produced and 21 percent better electrical current efficiency than the electrodes based on petroleum coke alone. It is suggested that larger scale tests are warranted.

Jan 1, 1970

By W J. Shaw

Geometallurgical modelling is now a hot topic in deposit evaluation and in optimising mine performance; however, its history is long and varied. Historically metallurgical sampling has frequently suffered from a lack of data due to the cost of producing representative bulk samples. In the early 1990s geometallurgical modelling similarly suffered from a lack of data due to complex, time consuming and expensive sampling techniques. More recently, simple and relatively cheap tests for geometallurgical variables such as hardness, grindability, throughput, SAG power index, bond work index, crushing index, mineral recovery and concentrate grade have become widespread. The cheaper sampling has resulted in relatively large geometallurgical databases. However, most of the geometallurgical variables sampled are implicitly (and incorrectly) assumed to be additive when modelled by traditional geostatistical techniques, often leading to ill-informed and costly decisions. Geometallurgical variables are mostly non-additive so the current geostatistical challenge is to develop new approaches to dealing with this type of data. This paper briefly describes a historical case study of geometallurgical modelling of the George Fisher Pb-Zn mine completed in the mid 1990s, then outlines some of the current misconceptions of geometallurgical data and modelling techniques regularly applied to it, and finally discusses some recent developments in geometallurgical modelling, with examples from a number of current clients indicating the direction forward.

Jan 1, 2009

As a society, the retiring age of workers is increasing. Individuals are having to consider working to an older age (beyond 55 years), the reason being to æpay offÆ debt, maintain a quality of life or, as a bigger picture, because society simply cannot afford the aging population. The Government is encouraging and promoting those approaching retirement to work to an older age to alleviate the financial burden of an aging population. In a working context those aged 55 years and over accounted for ten per cent of the Australian workforce in 1998 with this age group expected to account for half of the growth in the workforce between now and 2016. For the 60 - 64 years which account for less than three per cent in 1998, this group is expected to account for 15 per cent of the growth in the same period. As a result of individuals who have worked all their lives and in some cases æphysically hardÆ, they do not fully enjoy their years of retirement as a time when they get to choose what they want to do rather than what they have to do. Of particular interest are the physical or health related conditions that individuals end up with and the restrictions that ensue resulting in an individual being incapacitated either physically or with respect to the state of their health.

Jan 1, 2005

The efficient development and exploitation of an orebody relies on an understanding of the mineral characteristics of the deposit. This information is valuable throughout the mining cycle - during exploration, assessment, testing, design, operation and rehabilitation. Problems can arise at each stage if there is an inadequate appreciation of the mineralogy involved and its effects on the treatment process. Modern image analysis systems now permit a more quantitative understanding of the mineralogy of an ore to be gathered. Where previously the metallurgist had to rely on qualitative information to guide technical decisions, it is now possible to give numerical estimates to the compositional and textural properties which govern the mineral concentration processes. Ore samples can be characterised according to modal abundances, mineral grain size parameters and mineral associations, all of which affect the liberation and concentration of the values. The paper will discuss the application of quantitative process mineralogy by considering a number of case studies. These include: ore characterisation to assist in exploration, assessment and mine planning; modal analysis of complex mineral suites to assist in the evaluation of ores, the deportment of values between products and the recovery or loss of these values; liberation analysis for ore testing, plant optimisation and performance monitoring; and characterisation of tailing to guide estimates of leachability, stability and rehabilitation options.

Jan 1, 1998