Search Documents

The techniques used in evaluating gold placers and in recovering gold therefrom are briefly reviewed and critically assessed, relative to the estimated and actual recoveries from many operations. The discrepancies between these quantities can be significant and sometimes disturbing. The coefficient of variation for the annual percentage recoveries, relative to the estimates, is in excess of 10 and commonly above 20 . The difficult- ies in evaluating placers are recogni- sed both in the gathering of meaning- ful sample data and in the derivation of estimates. There are deficiencies, perhaps insurmountable at reasonable cost, in the techniques used to derive an estimate and in the gold saving devices usually employed. There is a subconscious trend to use recovery as a check on the estimate. The industry could have extracted more information during the evaluation and working of deposits in order to fully characterise them and in order to quantify metallurgical efficiency. There is a place for other prospecting techniques, particularly geophysical, in placer evaluation and a need for more appropriate and sophisticated

Jan 1, 1976

Water is important commodity in the mining industry. Water is used in the many stages of mining from the exploration stages and drilling, to mine development and operation and finally throughout mine rehabilitation and post mine activities. With the use of water throughout the life span of a mine, its management is an important component in the operation of any mine. Unfortunately the use of water within the operations can be one of the major sources of pollution generated from a mine. Such contamination can occur via numerous mechanisms including ground water flow, over land flow and accidents. Contamination may occur in any stage of mining operations, for example a leaking or failed tailings dam. With the above in mind, the paper presented will focus upon the use and management of water in the mining industry: ownership rights of water û common law as well as legislative rights; a review and analysis of the existing Queensland legislation and its mechanisms for the protection of water pollution from mining operations; and conclusions drawn from the paper relating to the Queensland legislation.

Jan 1, 2003

In the Ora Banda area of the Eastern Gold- fields, the ultramafic rocks tend to be more deeply lateritized than most of the surrounding rock types, and lateritic nickel concentrations have been formed. Extensive drilling_has shown that, of the two intermixed suites be- neath the laterite - an extrusive peridotite- pyroxenite suite and an intrusive, highly magnetic dunite - the latter weathers to a more nickel enriched laterite. The top horizon I of the laterite consists of ferricrete. Horizon II consists mainly of bands of secondary silica in a clay matrix, formed in the reworking zone around the water table and stranded as the weathering profile migrated downwards. Horizon III ('ºaprolite") is composed of serpentinite, magnesite, iron oxides and silica, and grades dowil to the fresh bock composed variously of olivine, ser- pentine, talc, amphibole-chlorite and iron oxides. The main locus of nickel deposition is the zone containing the bottom of horizon II and the top of horizon III. The water table is also at this general level. .

Jan 1, 1973

The efficiency with which it is expected that a particular coal may be burnt in a power station boiler significantly affects the value of the coal. Consequently many laboratory tests have been developed to provide data on the combustibility of coal. Computer modelling of coal combustion has also provided insight into limits on coal burn- out. Such modelling suggests that burnout of bituminous coal in a power station boiler will be strongly influenced by physical limits on the diffusion of oxygen to the individual coal particles. Coal chemical reactivity appears to be relatively less important. As a consequence of the diffusional limits, significant improvement in burnout is achieved either by producing less large p.f. particles or by providing sufficient furnace residence time to burn the large particles. Field data from a variety of power stations supports these cn.clusions. Burnout was also found to correlate well with volatile content for a number of coals from widely different sources. This is expected as the high vola- tile coals produce less residual char to be burned by the relatively slow heterogeneous Combustion.

Jan 1, 1987

By Manzoori AR

From a detailed combustion testing program and earlier experience with Leigh Creek coal, the Electricity Trust of South Australia (ETSA) gained a wide insight into the use of low rank coal fired boiler plant. This work is fundamental for the selection of boiler design parameters and other details which in turn determine the correct coal deposit selection for future power station development. In addition it gives boiler designers a good indication of the measures required to give reliable plant operation. Extrapolation from experience with existing plant, the designers main source of information, was not considered appropriate because of the lack of experience with similar coals. Brown coal beneficiation is also being assessed by ETSA in an attempt to improve the coal quality by the pretreatment of the raw coal prior to combustion in future coal.fired boilers. ETSA is also involved in the development of circulating fluid bed and gasification processes to determine whether these alternative processes are a more viable method of utilising the South Australian coals than pulverised fuel firing.

Jan 1, 1987

By J Walasiak

In the climate planning of mines and tunnelling with anticipated poor climatic conditions, and especially in case of longer working shifts, the main question is whether it can be reliably prevented that certain climatic limits laid down be exceeded. Working at high temperature and/or humidity can lead to reduced human working energy û a very important economic aspect û and to a risky lack of concentration on the part of the miners or to heat collapse and extremely dangerous heat stroke. With the Deutsche Montan Technologie GmbH (DMT) climate prediction programs, both the dry and the extremely significant humid heat transfer can be calculated. This is due to the high planning reliability involved. With the help of these climate prediction programs it is already possible to determine the anticipated climatic values for the operation phase as early as the planning stage of new ore or coal fields or of tunnel construction projects and to design the optimum air cooling system for every underground project with due regard to technical and economic aspects.

Jan 1, 2005

The comparatively low winter rainfall, exposure to heavy salt laden coastal winds, and the consequent high evaporation rate, are important considerations in the rehabilitation of the Maslins Beach Sand Pit. The deficit of rainfall over evaporation is assessed at 1085 mm per annum. Such a coastal environment complicates the establishment of plants. The endemic flora found on the Sand Pit environs is mainly low wind-planed shrubs and mat plants. The dunes near the coast support an association dominated by Atriplex cinerea, Spinifex hirsutus, Scirpus nodosus, and Olearia axillaris. The coastal cliffs carry a more diverse vegetation dominated by Beyeria lechenaultii and Eutaxia microphylla. Overburden is used to develop a new landscape to screen operations, batter final faces, and cover rubbish at the nearby Council dump. The early overburden dumps were built with little regard for stability, but the more recent practice of using scrapers has resulted in more stable dumps. The erosion problems created by poor compaction have been controlled by contour banks, diversion drains, bitumen lined run-off drains, and hay mulching.

Jan 1, 1976

An efficient filtration plant can be designed only from an adequate knowledge of the filtration characteristics of the material to be handled; if these characteristics can be expressed in the form of an equation the work of design is simplified immensely. The literature of the subject contains numerous equations which have been developed by various workers to express their results, usually obtained from a 'Very limited class of material, and from moderately thick pulps. Such expressions have been found quite unsuited for use in the case of thin, very free filtering pulps.In 1926, Underwood put forward an equation having a general for m, and which, he was able to show, provided a satisfactory expression of the data obtained and published by a large number of earlier workers. This equation has been found a very satisfactory and useful tool for the study of a variety of filtration problems. As thel basis of the equation is of assistance to the understanding of subsequent discussion, a brief account of Underwood's derivation is given here.UNDERWOOD's FILTRATION FORMULAEThe following symbols are used:

Jan 1, 1932

By C Standing, R Lacourt Rodrigues, C Q

The value of iron ore depends on the grade of the contaminants. Scheduled iron, and the associated contaminants, provides mine planners with a measure of stockpile feed and blending requirements. Blending at the stockpiles is one approach to optimising iron grade, while minimising the variability of contaminant grades. These schedules are typically based on resource models incorporating geology and iron and contaminant grades. Resource models reflect best estimates of trends for each of the elements rather than the potential variability, which is critical for accurate short-term blending. Conditional simulation provides a tool to describe the likely variability of each element. Only recently has conditional simulation technology allowed the inherent correlation between elements to be incorporated into the process. This paper presents the stepwise co-simulation process used to simulate and describe multi-element variability for effective mine planning. A case study using the multi-element conditional simulation and the subsequent uncertainty in the schedule and stockpile planning is presented. This process supports proactive mine planning to minimise unexpected fluctuations in the final product.

Jan 1, 2005

Recent well-publicised problems with the start-up of new mining projects have continued to feed the perception that the mining business in general and Ore Reserves in particular are a poor risk. New mines commonly experience difficulties when the true variability of ore characteristics becomes apparent during commissioning. At this critical stage, the impact of lower metal recovery, reduced throughput or increased consumption of reagents and energy can have a catastrophic effect on economic returns, as illustrated by the premature closure of some operations. There appear to be several common reasons contributing to the poor performance of mining projects, of which three are examined here: lack of early risk assessment before feasibility studies are started, inadequate sampling for metallurgical test work and variability of the run-of-mine (ROM) ore. An underlying feature of these issues is the lack of effective interaction between geologists, mining engineers and metallurgists/ process engineers. Geologists need to be more aware of ore processing issues and the range of characteristics that need to be considered as part of the resource estimate. Metallurgists need a greater understanding of the variability of the run of mine ore in terms of all the characteristics that influence the design and operation of the plant. Mining engineers need to determine the short-term variability of the ore in the mine schedule, so that there is confidence that the quality of the run-of-mine ore will be within the design specifications of the plant. A substantial overlap between these disciplines and sharing of areas of responsibility is necessary if these and other technical problems are to be better understood, production estimates are to be improved and commercial risks are to be reduced. Although the JORC Code (1999) provides guidelines for reporting all the issues that are material to an Ore Reserve estimate, some issues are rarely fully addressed in Ore Reserve reports. In particular there is no formal requirement for a metallurgist to assure his or herself of the appropriateness of the Ore Reserve classification. Consequently the level of uncertainty related to recovered grade and ore processing characteristics may be understated. It is suggested that to meet the concerns of bodies funding new mineral developments a stronger multi-disciplinary approach to the analysis of mineral deposits and reporting of Ore Reserves is required. The culmination of this approach would be the formal requirement for a geologist, mining engineer and a metallurgist to co-sign Ore Reserve reports.

Jan 1, 2002

By Savidis G

The characteristics of 'Z' (Back-over run) and 'R' (Reverse) ventilation systems are dis- cussed in relation to their suitability for longwall mining. Experience in European mines has been described as a basis for comparison with Australian conditions. In assessing the merits of each ventilat- ion system, such factors as longwall layout (pillar design, number of headings and gateroad stability), the need for gas drainage and bleed- er systems, as well as the influence of seam dip have been considered relevant. The R system is generally applicable for single and two heading development in seams where gas emission is a less serious problem. In contrast, the lower extraction to development ratio of the Z system (which arises from using three or more heading layouts) is considered more favourable where high gas emission occurs. The Z system provides greater flexibility with respect to the provision of refreshing air at the tailgate end, access of men and materials, installation and retrieval of gas drainage systems and the ability to interchange main- gate and tailgate roadways in cases where roof strata loads are difficult to control, or where cpam in hac an influrnra

Jan 1, 1983

By R Morrison, P Owen

Particle breakage is an essential part of mineral processing. The aim is to reduce run of mine mineral ore to an optimal size for liberating target minerals and for subsequent recovery by separation processes such as flotation. This size reduction is typically accomplished in a series of stages in a grinding circuit tailored to the properties of the particular mine ore. Commonly this involves two or more classes of equipment starting with crushers, followed by SAG mills and then sometimes ball mills. Occasionally, high pressure grinding rolls or other novel devices are substituted. Broadly, energy consumption increases and energy efficiency decreases with the fineness of the material produced by each piece of equipment. For many operations, up to 50 or 60 per cent of total greenhouse gas emissions from a plant arise from the operation of the comminution circuit with the majority produced by the finest grinding parts, such as the SAG and ball mills. Wear of mill liners and grinding media also add to greenhouse gas emissions generated by their manufacture. The need for continual cost reduction and increasing regulatory and social pressure relating to greenhouse emissions create a strong need for improvements in comminution energy efficiency. Traditional experimental and modelling approaches are not well placed to create the required insights into comminution fundamentals or facilitate radical step changes in performance. This paper discusses the role that advanced modelling (based on coupled DEM and CFD) can play in improving the energy efficiency and performance of existing mainstream grinding equipment and in the development of new ones with radically superior performance. Achieving this goal will also require an improved understanding of ore breakage and methods to include sufficiently realistic breakage models within the DEM models. Developmental issues for the modelling and the critical need for validation of the advanced model features are highlighted.

Jan 1, 2004

The Permian rocks at Gympie were first studied as far back as 1868 in conjunction with the discovery of gold. The relationship of the Gympie Group to other sequences in the Gympie Composite Terrane is an important subject of investigations in a new mapping project of the Geological Survey Program of the Department of Resource Industries.In two areas the Gympie Group has been divided into four defined formations. They are the Highbury Volcanics (base), Ram mutt Formation, South Curra Limestone and Tamaree Formation (top) in the Gympie area, and the Mant basalt (base), Kolbar Formation, Gigoomgan Limestone and Teebar Formation (top) in the Gigoomgan area. Geochemical and lithological evidence from the basal volcanics of the Gympie Group (Highbury Volcanics, Mant basalt) indicate that they developed in an intraoceanic island arc setting. The overlying volcaniclastic sediments (Rammutt Formation, Kolbar Formation), which contain some continentally-derived material, are mainly of local derivation and shallow-water marine. A hiatus is present at the top of the Early Permian Rammutt Formation and Kolbar Formation. Following the hiatus, limestone sedimentation characteristic of a basin of restricted circulation developed in the Late Permian. There is some evidence of a hiatus between the limestone deposition of the Gigoomgan and South Curra Limestones and the overlying probable turbidite deposits of the Teebar and Tamaree Pnrmatinnc

Jan 1, 1990

By W Schauenburg

The increasing problems associated with the disposal of waste and the potential for use of by-products as underground filling material is a subject which is relevant not only to the coal-mining industry. The progressive scarcity of surface disposal facilities for by-products and waste has now become a problem in all sectors - not only for the mining industry. The considerable capacity offered by underground cavities which exists in various mining branches present an extremely promising potential in this context. The backfill process for coal mining developed by DMT in co-operation with Ruhrkohle AG make use of the cavities which are offered by the extraction of coal. It consists of several stages: The fine-grained by-products, such as sludge, filter cakes, fine refuse, ash and flue-gas cleaning residues are processed on the basis of specified formulations in metering, blending and pump facilities on the surface to produce pumpable pastes with precisely defined flow characteristics. On Walsum Colliery of Ruhrkohle AG up to 200 m3/h stowing paste is conveyed into the mine in pipes with diameter of 200 mm (8"). The delivery pressure of the pump operating on surface in conjunction with the hydrostatic pressure of the shaft pipe - amounting in total to as much as 25 MPa - makes it possible to convey the stowing material for a distance 12000 m underground up to the workings without any need for additional booster pumps. Via a pipe installed in the face, the paste is pressurised into the cavities in the specially fragmented rock in the mined-out zone well behind the support. Consistent use of stowage of caved-in goafs makes it possible to reduce surface settlement above the workings. Fires in the stowed rock are either smothered or completely prevented thanks to the exceptional air-tightness in the caved goaf and the cooling effects of the slurry stowage. The reduced danger of fire, the preventation of air-leakage and the positive effects on gas emission from the coal improve safety in the workings.

Jan 1, 1998

By Marwick PL

As part of its operations Hamersley Iron operates a heavy medium Concentrator to upgrade low grade, unsaleable iron ore to produce saleable lump and fines products. Firstly, the attempts at delivering a blended feed in both chemical and physical characteristics are presented. Improvements in blending controls are shown to have given process performance improvements. Secondly, improvements to the feed preparation section are detailed. These alterations are providing a much cleaner feed to the subsequent processing stages.

Jan 1, 1987

Iron formation-hosted iron ore deposits account for the majority of current world iron ore production and consist of three classes: unenriched primary iron formation with typically 25 to 45 wt per cent Fe; martite-goethite ore formed by supergene processes, with abundant hydrous iron oxides containing 60 to 63 wt per cent Fe; and high-grade hematite ores thought to be of hypogene or metamorphic origin overprinted by subsequent supergene enrichment with 60 to 68 wt per cent Fe.Individual iron ore deposits range from a few millions of tonnes to over two billion tonnes at >64 wt per cent Fe, although most are within the range of 200 to 500 Mt. In the Hamersley Province of Western Australia, martite-goethite ores are largely developed in the Marra Mamba Iron Formation, although high (>0.08 per cent P) phosphorous mineralisation is also well developed in the stratigraphically higher Brockman Iron Formation. Whilst the vast majority of high-grade microplaty hematite ore is best developed in the Brockman Iron Formation, this paper provides the first textural evidence of locally significant microplaty hematite mineralisation in the Nammuldi Member of the Marra Mamba Iron Formation, in the Chichester Ranges at the Christmas Creek, Cloud Break and Mount Nicholas prospects. Petrographic studies have identified a high-grade Fe texture composed of nanometre scale plates of hematite in mineralised sections of primary microplaty hematite deposits in the Pilbara and elsewhere, well below the normal depth of weathering or dehydration. The population of nanometre to micrometre scale hematite plates is interpreted to represent various stages of nucleation, crystallisation and progressive growth of hematite from the primary ore-forming fluid in areas that were once iron-rich carbonates or silicates in the BIF.

Jan 1, 2005

By Komosa T, Muir D. M

Adequate levels of dissolved oxygen are essential for efficient gold dissolu- tion. The actual levels in plantpuips can be seriously reduced by the presence of oxygen consuming reactive minerals, and reduced oxygen solubility in saline water. The rate of gold dissolution is then limited by oxygen availability rather than cyanide. Ion selective electrode dissolved oxygen meters can give an effective indication of the relative oxygen saturation, but they are not able to give meaningful values of dissolved oxygen in saline water, without custom calibration curves. When the dissolved oxygen concentration is rate limiting, the addition of oxygen or peroxide can improve gold leaching kinetics as well as reduce cyanide consumption.

Jan 1, 1991

By Warner N. A

There is an inherent problem in producing simultaneously lead, zinc and copper as metals in a single polymetallic smelting furnace. It relates to the condensation of lead and zinc from the gas phase under vacuum conditions such that metals in bulk form, either solid or liquid, are obtained as products rather than a fume or dust containing both metallic and non-metallic components. To understand this phenomenon, it has been necessary to establish mathematical models with computer simulation to identify the process requirements for effecting the objective of maximum bulk metal production with minimum fog formation. The theoretical framework of simultaneous heat and mass transfer involved in condensation from gas mixtures containing a non-condensable gas has been extended to the high temperature and reduced pressure conditions. These apply to new technology for polymetallic smelting now being developed in a project currently funded jointly by the Commission of the European Communities and the Mineral Industry Research Organisation. Under the right conditions it is theoretically possible to condense out both lead and zinc with minimal fume formation, but in all practical cases it is anticipated that some circulating load for reversion back to the smelter will be needed.

Jan 1, 1989

The distribution of p(~rphyt1 copper deposits, in time as well as place, is used to propose an occurrence model based on the genesis models of Sillitoe and Rona. A magmatic source of the metals is accepted. The characteristic metallogenic epoch and the migration of the mineralization event along an elongate metal province are explained as the result of subduction of an obliquely- oriented strip of mineral-enriched material on the oceanic plate. Two mineral-enriched trails emanate from a hot-spot source of high-intensity hydrothermal activity in an oceanic rift. Because the whole plate system moves relative to hot spots, the hydrothermal source appears to migrate along the rift, and the two trails are not parallel to transform faults, but form a broad "V" centred on the hotspot. Source loci are spaced at intervals of about 3000 km, resulting in the possible repetition of metallogenic epochs, in a subduction zone province, at about 100 m.y. intervals. The position of the mineral-enriched strip can be found graphically, given ages of a series of deposits in a province, and the plate convergence vectors. This knowledge provides an exploration tool at regional scale and, by reflection across the rift, the potential for exploration is extended across oceans. The model has implications for commodities and deposit types other than porphyry coppers.

Jan 1, 1987

By Kubik K

Recent significant advances in the Global Positioning System (GPS) have contributed to making real-time kinematic/dynamic process for decimetre to centimetre-level positioning more reliable and ready for the production-use. As a result of research and development efforts in this area, a robust real-time kinematic (RTK) GPS positioning prototype system has been established at QUT for both scientific and engineering purposes. This system is finding applications in a wide range of automobile robots or automatic guidance vehicle systems. This paper first summarises the theoretical basis necessary for centimetre real-time kinematic positioning, then gives a brief description for the real-time dynamic GPS system developed at QUT. The paper summarises the results of a designed vehicle tracking test. The results demonstrated that the differences between RTK filtering solutions and OTF solutions are in the order of magnitude of about 20 centimetres and the accuracy of OTF solutions are in the levels of two centimetres. This confirms that the RTK system delivers three-dimensional position with decimetre-to-centimetre accuracy. This particular RTK processing system is robust and reliable, although the system is referred to as a prototype and will be further developed.

Jan 1, 1997