Search Documents

The scope of this paper has been restricted to the manufacture in Australia of seamless steel tubing, as the subject of buttweld tubing has already been dealt with by A. N. Hamilton in a paper delivered before the Institute in 1935.The earliest attempts to produce seamless steel tubes were based on the extrusion of lead piping, a process developed by Thomas Burr in 1820. However, the problems associated with the extrusion of white hot steel had to await the metallurgical knowledge of the twentieth century, and these early attempts were unsuccessful.The years 1840 and 1845 were noteworthy for the introduction of the first practical methods of making seamless steel tubes. In one process, a large circular plate was 'cupped' in a vertical press; in the other, a round steel billet was pierced for its entire length.The product from both these methods was then elongated by repeated reheating and rolling over an internal mandrel, in a circular pass mill.At this juncture, it should be noted that every process developed for the manufacture of seamless steel tubing can be divided into two parts. In the first part of the process, attention is centred on the conversion of the heated bloom into a short, thick-walled, hollow cylindrical forging; this product is then elongated in the second section of the process. It will be noted that these two sections are actually quite distinct, and in practice numerous methods exist for carrying out both functions. The first stage is generally referred to as 'piercing', the second stage being termed 'elongating.' In this paper, the author proposes to outline the various methods adopted for piercing and elongating; the reader is asked to note that although certain methods of piercing are almost invariably associated with only one method of elongating, the distinction between the two functions is, nevertheless, a vital one and should be noted accordingly.

Jan 1, 1947

By Munro DL

The Mary Kathleen uranium deposit is in north-west Queensland, approximately halfway between the townships of Mount Isa and Cloncurry, at long. 1400 009 E and lat. 200 44' S. The deposit Iwas discovered by prospectors of the Walton McConachy Syndicate early in July, 1954, and climaxed a very intensive ground search by hundreds of part-time prospectors. during the uranium boom from March to July 1954ò Numerous small deposits, mostly in the vicinity of Mount Isa, were discovered in various rock environments, but Mary Kathleen is the only large deposit and, apart from a few tons of hand sorted material from the Milo lease, is the only deposit that has been worked. Exploration of the surrounding area, and proving of the economic worth of the deposit, were conducted from the time of discovery until February 1956 by a geological team camped near the deposit. Proving was carried out by drilling a pattern of vertical and inclined diamond drillholes at fifty-foot centres over the outcrop. An adit was driven eastwards through the deposit. Metallurgical research and design work in the South Australian Department of Mines Adelaide Laboratories were based on core samples and bulk samples from the deposit. The signing of a contract in March 1956 with the British Atomic Energy Authority to supply 4500 short tons of uranium oxide allowed mining to commence, and enabled the planned construction of water supply, township and treatment plant to proceed. The open out mine and plant are now serviced by a modern township, four miles away, which is connected to Cloncurry and Mount Isa by road. Although little field work has been done since the exploration phase, this paper differs in interpretation from a previous paper (Matheson and Searl, 1956) in that it is based on a revised structural inter- pretation (Compana, 1958), detailed mapping of progressive exposures in the open out, and a re-examination of diamond drill cores.\

Jan 1, 1968

EQUIPMENT TO BE DISCUSSED It is the intention of this paper to discuss the transporting of large skid mounted equipment and track machines around open cut mines. By large I mean 100 to 350 tonne capacity being trans- ported on minesite lowloaders and the capability of moving loads of 300 to 1200 tonne by other means. It is also possible to move larger loads. The main factor in transporting large loads is eco- nomics and is a balance between the cost of the transporter and the increased production from the equipment being moved. For example it could be possible to shift a 7000 tonne dragline faster than their own means of propulsion, being the "walking feet" method. However for the cost of $10 to $12,000,000.00 or more you can afford to walk the dragline and suffer the production loss. Let us concentrate on the economically realistic. BOSICH FBT MINESITE LOWLOADERS 100 TO 350 TONNE CAPACITY. Why initially consider having such a transporter? Our experience has shown that initial enquiries evolve from mines requiring to move large drills, 50 to 200 tonne weight and large hydraulic excavators or backhoes which are track mounted. The reason for shifting them is to move equipment from a mining face to enable blasting, to remove to the central workshop for repairs, overhauls and routine maintenance, to transport equip- ment from one mine face to another, and for drills, to move from one drilling pattern to the next. The cost in terms of time lost and extra wear on tracked equip- ment easily justifies the cost of the transporter. The tracks on large drills and shovels are not intended for long distance walk- ing. These tracks are designed to move the machines to position for drill holes, or moving around the mine face. Long distance travel, ie generally 1 km or more, results in overheating of track rollers, track drive components and accelerated wear on tracks.

Jan 1, 1989

Instantaneous outbursts of coal and gas have occurred in Australia in the Sydney Coal Basin since 1895 and in the Bowen Coal Basin since 1954. The largest has been about 500 tonnes of coal and so their magnitude and character have not approached those experienced in some other countries. The occurrence of CO2 with some Australian cases provides some similarity with the worst affected areas in France and Poland.The proneness of seams depends on coal rank and seam gas composition, among other factors. The proneness of places depends on depth, structure, intrusion, tectonism and other factors affecting the geometric, physical and chemical uniformity as well as details of mining. As a phenomenon due to gas and stress, prevention can be achieved by relief of high gas and/or stress condition. Alternatively, controls can be applied to render mining safe for personnel. Unfortunately day-to-day prediction is not widely and reliably achieved to allow selective use of prevention or control. The initial rate of desorption is the most promising day-to-day indicator.Various researches include gas conditions and parameters, stress and failure conditions and parameters, coal variables and geological variables in relation to prediction, prevention and control. Some assistance in research may derive from study of analogous phenomena of instantaneous outbursts of salt and other rocks and gas. It is concluded that in the Sydney and Bowen Basins, any coals with less than 30 per cent Volatile Matter (VM) ash free dry (afd) at depths over 200 m could be prone. Proneness increases with depth, with lower volatile content, with geological disturbance including faulting, intrusion and recent tectonics, with increased CO2 in seam gas, with narrow work and with other factors. Much more research is needed.Unfortunately outbursts are needed too, to provide the research with realistic data. With the problems of mechanism and prediction still being unsolved much research remains to be done. No present aspect of research is satisfactorily resolved.

Jan 1, 1983

By N S. Rauert

The Barrick Gold Granny Smith underground operation located at the Wallaby deposit is currently in a transition period from a near surface operation in ramp up mode to a fully operational deep mining operation with annual production exceeding 1 Mt/a. A key element in this process has been the project execution of the Wallaby Deeps project from initial scoping study in 2007 to the major production component of the Wallaby operation by 2013.The Wallaby Deeps project serves as an example of how an ongoing detailed study program can be integrated into a day to day mining operation assessing risk and mining application in a perceived challenging narrow vein geotechnical environment prior to mining. A detailed study phase to feasibility level is carried out prior to the mining each zone of Wallaby with mining approval only granted on study completion with full justification.A central element in this process is an optimisation study that utilising the Mineable Shape Optimiser (MSO) and Schedule Optimisation Tool (SOT) software tools developed by AMIRA Ltd PRIMO research project is used to carry out an NPV value based option study. This optimisation process being then tempered to reality by a predefined practicality assessment process utilising extensive peer review by operational and study team members as well as industry experts.Other challenges facing the Wallaby Deeps project include the requirement to maintain the ramp up production profile to full production by 2012 without disruption but with pressures of an ongoing geological resource to reserve conversion program essential for the study process and mining approvals and also development rate achievement.To date these challenges are being met with integrated planning and the value of the study program itself. Production in 2012 year to date is well on the way to annual production rate exceeding 1 Mt/a.CITATION:Rauert, N S, 2012. Wallaby Deeps - from the optimal opportunity to reality, in Proceedings Narrow Vein Mining 2012 , pp 207-214 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

In July 1994 the Premier, John Fahey MP, announced that the New South Wales Government would make available a total of $40 million over six years in new funding for the Department of Mineral Resources. These funds are to be applied directly to the generation of regional geological and geophysical information. The Government's initiative known as `Discovery 2000', is aimed at providing a major boost to the exploration industry. The Government expects new discoveries to be made and new mines to be developed because of the initiative and, perhaps, the first ever commercial oil or gas production in New South Wales. The Government's return will come from increased economic activity, and from the increased royalty return from higher levels of production. Quality information is the key to successful exploration. In the highly competitive business of mineral and petroleum exploration high quality regional geological and geophysical information improve both the efficiency and effectiveness of the area selection or project generation process. Using the `needle in the hay stack' analogy, Discovery 2000 will vastly improve industry's chances of finding the haystacks. It is up to the mineral and petroleum industries to find their respective `needles'. Careful target area selection is probably the most critical factor in mineral exploration. The ability to select the most prospective areas, or to identify prospectivity that others have failed to recognise, can make all the difference between success and failure. Government geological surveys clearly have a crucial role to play in providing the geoscientific information infrastructure that companies must have if they are to make the discoveries this country needs to pay its way in the world. It is the regional information generated by Governments that sets the scene for efficient exploration. This regional information includes regional aeromagnetics and radiometrics and gravity, regional geological mapping and tectonic analysis, and geoscientific databases. The New South Wales Department of Mineral Resources (by various names) has been providing such information for over 100 years and has led the way in many aspects of the generation and dissemination of geological, geophysical and metallogenic Information.

Jan 1, 1995

It was Harold McMillan, Prime Minister of England 30 years ago, who used the phrase "The Wind of Change" to describe political events in Africa in his day. So well did this phrase capture the spirit of the time that it echoed around the world, and the echo has never stopped. Change is the constant factor in the society in which we live and everyone of us has had experience of the effect which it has had on our professional and personal lives.Change will not stop, it will continue at an increasing rate and the questions we must answer are how do we prepare ourselves to meet the challenge of future change and how do we take advantage of the opportunities which it will bring?It is these questions which I wish to discuss in this address.There is nothing new about change in the mineral industry, it has been happening for thousands of years and it will continue as long as civilisation exists on earth. One type of change is economic and we are all aware of the rises and falls which occur in the prices of metals and minerals (Figure 1). When these have happened in an orderly manner, and could be predicted and planned for, it has been possible to take advantage of the benefits and minimise ill-effects, but when they were sudden and precipitate, and could not be predicted, the consequences were serious. The extreme example, of course, was the oil price shock of the 1970s which had such disastrous effects on industry and society.Other types of change are social, cultural and political. They have all been important in recent years and will continue to be so in the future.But it is technological change which may well be the most important because its effects are profound and irreversible, and alter irrevocably the way in which we live. So in discussing the mineral industry in a changing world I will talk specifically about technological change.

Jan 1, 1989

By N Strong

Cracow is a high-grade; low-tonnage underground gold mine located approximately 500 km north-west of Brisbane in Central Queensland. It is a steeply dipping, narrow vein, epithermal gold and silver deposit that is accessed via a decline from surface. Cracow is owned by joint venture between Newcrest Mining (70 per cent) and Sedimentary Holdings (30 per cent). The orebodies are 5 m wide on average and the ore is extracted via sublevel open bench stoping. Stopes are extracted to a strike of approximately 25 m before being backfilled with waste. Prior to the introduction of electronics, the mine would remove a small amount of the previous backfill out to create a void, and then begin blasting two to three rings at a time, with the ore being extracted between each blast. This method caused the ore to be blasted onto the waste backfill resulting in dilution of the high-grade ore. It also meant that the extraction of each stope took a number of weeks and numerous blasting events. In the fourth quarter of 2005, the mine struck a geotechnically sensitive stope, where all 20 rings had to be extracted in a single shot or risk possible geotechnical problems that could sterilise the ore. Due to the limitations of NONEL« delay detonators the mine could not fire all the rings in a single shot and needed to use an electronic detonator system to extract the stope. Some unexpected benefits to the mine were increased fragmentation, reduced vibrations, reduced dilution, improved efficiency and improved hanging wall and footwall conditions. After the success of this first electronic shot, the mine has since moved to firing all their stopes with electronic detonators. With electronics the mine has been able to fire much larger blasts, and has in fact moved to firing their blasts in the opposite direction, firing towards the draw point instead of into the waste backfill, thus reducing ore dilution.

Jan 1, 2008

By T Lancaster

The Mount Gordon operation, consisting of the Esperanza open cut mine and the unique Mount Gordon Ferric Leach processing plant, is operated by Western Metals Copper Ltd at Mount Gordon, 125 km north east of Mt Isa. The processing plant treats predominantly the secondary copper sulphide minerals, chalcocite and covellite. The gangue consists of massive pyrite and a range of silicified siltstones. The processing plant utilises a conventional single stage SAG/cyclone milling circuit, followed by low-temperature/low-pressure autoclave oxidation to produce copper in solution. The pregnant leach solution is treated via conventional SX/EW technology to produce copper cathode. Currently the plant is operating at a nominal production rate of 48 500 tpa copper. The Mount Gordon Ferric Leach technology is the worlds first integrated pressure leach/SX/EW process to be used to treat copper sulphides on a full plant scale. In the last six months, July to December 2001, the plant has emerged from a two-year postcommissioning phase to achieve steady state operation. This has been characterised by high plant availability and consistent production performance in excess of the name plate capacity of 45 000 tonnes. Production rates will continue to increase over the next 12 months to over 50 000 tpa via a planned process of incremental improvements. The pressure leach circuit has consistently achieved availabilities exceeding 95 per cent over the past 18 months. Notwithstanding this, the leach circuit still has a much greater requirement for planned maintenance than SX/EW. For much of the Mount Gordon processing plantÆs operating life, the leaching process has constrained production. Recent developments arising from detailed mass and energy balance modelling have now significantly improved leach capability, resulting in the plant bottleneck being shifted to electrowinning. In order to balance the capabilities of the two circuits however, the surge capacity between leach and SX/EW was increased substantially. This effectively de-coupled the higher capability but lower availability leach circuit from the lower capability but higher availability SX/EW circuit. As a result, electrowinning utilisation has increased to in excess of 98 per cent, which is reflected in a higher overall plant throughput.

Jan 1, 2002

By Crawford M

During the initial development of Mount Isa Mines power was supplied from a temporary power plant situated near the Man & Supply Shaft. The main power plant was placed in service early in 1931 and then comprised two Babcock and Willcox boilers, fired by pulverised fuel, and two British General Electric Company's turbo-alternators of 5,000 kW. each. Both plants have been described by A. F. McAskill in the Journal of the Institution of Engineers, Australia.From 1931 power demand progressively increased due to greater production, further mine development in the harder sulphides increased pumping for mine drainage and additions to mill and smelter until, by 1935, the plant was inadequate for further output commensurate with a reasonable safety margin.Coincident with the added power demand, operating conditions involved a fuel problem which could not have been anticipated. The ash content of the fuel supplied gradually increased from 13% to 16-5%, while the melting point of the ash decreased with higher pyrite content.Temperature conditions in the furnace required careful control to cope with ash formation and slag accretions.Consequently brickwork, excessively stressed on water walls, was constantly under repair, and required suspension periods of 50% of operating time for cleaning and overhaul.Load conditions varied continually, therefore the high heat liberations in the furnace, necessary to accommodate peaks in fluctuating output, resulted in ash fusion.

Jan 1, 1939

This paper summarises the performance of the gold exploration industry in the Western World since 1970, with particular emphasis on the period 1985 - 2003. It identifies the number and size of major (ie >1 million ounce) primary gold discoveries made over this period by location and type of company. Estimates are also made of the likely contribution from smaller discoveries down to 0.1 million ounces. It also assesses the overall trend in the percentage of grassroot discoveries that are converted into mines, and the time taken to get them into production. By comparing the discovery data against total exploration expenditures it is possible to determine the average unit cost of finding a major gold deposit. It is significant to note that the average unit cost per discovery and per ounce of resource has tripled over the last 30 years. An attempt is made to determine the overall economic value generated by the industry. This is based on a detailed analysis of the rates of return and the Net Present Values (NPVs) of 109 major gold projects. After including an adjustment for discoveries not modelled, the NPVs are compared against the total amount of money spent on exploration to determine the value-to-cost ratio for the industry. Based on historical spot gold prices and tax rules, it is found that the return on investment for gold exploration in the Western World over the period 1985 - 2003 was around five per cent real after-tax. The returns achieved in the US and Australia was significantly higher than that for Canada. The returns also appear to have declined in recent years. With regard to the relative performance of junior versus major companies, the paper estimates that the junior sector accounted for 30 - 40 per cent of the total exploration expenditure, and were was associated with 34 per cent of the total number of major deposits, 27 per cent of the contained ounces and 25 per cent of the economic value found.

Jan 1, 2004

By Hilde TWC

Synthesis of GLORIA side-scan sonar and other geophysical data has provided morpholo- gical and tectonic details of the interaction between the Nazca and South American plates along the Peru Trench (80S-15¦S). Our analyses suggest that a new propagating rift of the Galapagos type is evolving along the Mendana Fracture Zone (MFZ). Subduction induced rift- ing of the Nazca plate is accompanied by organized seafloor spreading for the last 3 Ma at least. GLORIA sonographs and bathymetric mapping show an 8-10¦ divergence in MFZ width towards the Peru Trench. The fracture zone comprises numerous ridges and troughs and a lack of sediment cover in the axial part. Young magnetic lineations (anomalies 1-2A) are observed within the fracture zone wni.cn are orthogonal to the older Nazca plate lineations. The central anomaly narrows west- ward and can be observed up to 400 km seaward of the trench whereas anomaly 2A is terminated about 200 km from the trench axis. Recent SeaMARC II sonar mapping in the region shows large igneous blocks in the Trench axis to the north of MFZ but absent to the south. We believe these blocks represent young seafloor of MFZ rift/spreading center broken off from the ridges as they subduct along the Peru Trench. The MFZ rift is propagating west- ward at a rate of 115 km/Ma (25 km/Ma relative to the South American plate). Given the present rates of accretion at the East Pacific Rise and of propagation along MFZ rift, the Nazca plate will be divided into two parts in about 35 Ma.

Jan 1, 1987

About 60 persons are admitted to the graduate course every year after passing the entrance examinations. The entire course of studies is free of charge and the universities provide accommodation for the students who need it. The five years of studies are divided into 10 semesters. One semester lasts 15 weeks. Automatics can be studied at three separate faculties. At the University of Mining and Metallurgy, it is offered by the Faculty of Electrical Engineering, Automatics and Electronics as well as the Faculty of Mining and Metallurgical Machines (metrology can also be studied there); at the Silesian Technical University in Gliwice, the Faculty of Mining offers the course. The educational plans and programmes comprise 3 groups of subjects: common for a given course of studies (foreign languages, political science and the basic technical knowledge) common for the speciality and subjects of diploma courses. The whole time of studies covers about 4400 hours excluding 3 periods of professional training and the physical training. The classes, laboratory classes, seminars and design classes are obligatory and the attendance is strictly checked. Students may extend their knowledge by participating and working in the Science Clubs. The students' work is checked not only during the classes but also by the examinations held at'the end of respective semesters. Those who fail the exams can repeat them only if very important reasons are presented. At the very end of the studies there is a diploma examination together with a discussion on the diploma thesis, written by the student. The successful result entitles the student to recieve the title of "magister inzynier",M.Sc. of his speciality. The graduates, after working for 2 years, can attend another course of studies lasting 2 semesters and called "Postgraduate Course", or start "Doctoral Studies" finished by the defence of a doctor's thesis. In'these cases the expenses are usually covered by the graduates' employers.

Jan 1, 1985

Australian wheat belt agriculture is causing a decline of its natural resource base. The major problem, salinity, arises from a small reduction in water consumption by agricultural crops compared to what prevailed under the prior native vegetation. This causes groundwater accumulation which, in the low relief landscapes of the wheat belt, is leading to extensive surface saturation in low landscape positions and dramatic, destructive change in the hydrological behaviour and habitat of streams and rivers. The ability of agriculture to invest in salinity control is severely limited by its long-term decline in its terms of trade. Extensive planting of perennial vegetation has the potential to increase water use and arrest the salinisation process. If these perennials were also commercially attractive, the cost of salinity treatment could be minimised. Given the difficult commercial position of food commodities, it is logical to develop ænon-foodÆ perennial crops, in particular woody crops suitable for industrial products. This paper looks at the example of Sweden, where there has been a generation of investment in developing forest harvest residue recovery, and short cycle woody crops for bioenergy, but with only limited success. In contrast, secondary residues (processing wastes) from forestry industry are readily saleable for low value uses like bioenergy. This suggests that the model woody crop must have a higher value fraction to facilitate delivery and commercial use of its lower value fractions. This model is being emulated in the development of native mallee eucalypts as short cycle woody crops in Western Australia. Some $50 million has been expended on mallee development in the past decade and this has culminated in an engineering demonstration of integrated processing. The putative high value products are activated carbon and eucalyptus oil and the residue (plus waste heat) will be converted to electricity. The potential scale on which crops of this type would be required to achieve salinity control means that many more high value and residue products will have to be developed. Metallurgical charcoal appears to be a promising product option.

Jan 1, 2006

THE object of this note is to set forth some particulars of the effect of light on cinnabar occurring in a deposit of this mineral at Puhipubi, in the North Auckland peninsula of New Zealand. This deposit is contained within a gently-inclined sheet of siliceous sinter forminga hillock called Mount Mitchell, and is particularly notable in that it is an instance of the simultaneous deposition of cinnabar and silica on a large scale. The mercury-bearing material varies in character from semi-porous sinter to dense translucent cbalcedony, of which the former is stained to various shades of pink, the latter to brilliant reds and vermilion. On exposure to daylight-and particularly to sunlight - these colours change to corresponding shades of translucent bluish-grey. As a direct result of this change the Mount Mitchell deposit remained unknown until some ten years ago, for, while prospectors early discovered cinnabar in the adjacent city and in a neighbouring stream bed, none of them recognized this mineral in the bluish chalcedony strewing portions of the surface of the Mount. The writer has carried out a series of experiments designed to indicate the cause and nature of this change, and to form a basis for the elaboration of more delicate experiments which would yield positive information. Circumstances, however, have so far combined to prevent the continuation of the research, and, as there seems little prospect of the writer being able to do more work on the subject, it seems well to publish the data so far obtained. Prior to describing this colour change, the writer would point out the desirability of restricting the meaning of the term cinnabar to the naturally occurring red sulphide of mercury; this would eliminate the ambiguities which arise from its indiscriminate application, in chemical literature, to both natural and artificial sulphides. Further the term cinnabarite having long since fallen into disuse, there appears to be no good reason for retaining the companionterm "metacinnabarite" when reduction to "metacinnabar" would preserve the meaning in a less clumsy word.

Jan 1, 1923

By Roxborough F. F

The ability of the Australian minerals industry to successfully manage the changes and challenges that face it in the 21st century depends ultimately on the quality of its human resources. Mining engineers have a vital role in this regard. The education and training that universities are currently giving to mining engineers is under challenge and needs to be reassessed in the light of industry directions for the 21st century. At one extreme is a push for a `finished product' graduate, up and running in `the flavour of the month' issues. At the other extreme are moves to reduce face-to-face university teaching hours and return to the time honoured university concept of `reading' for a degree. The lessons of Mourn make it apparent that neither approach is appropriate to the industry's future needs (Windridge, 1996). Basic knowledge gets rusty with time and new skills need to be learned. In order to conduct mining operations safely, productively and competitively, mining engineers must now accept the need to be prepared for continuing professional development as a career imperative. The concept of being professionally or statutorily qualified for life is no longer valid. This calls into question the purpose, content, structure and mode of delivery of university courses, all of which need to engender the principle and facilitate the cause of continuing professional development. This paper presents a model which aims to deliver a quality assured university education for mining engineers for the 21st century at undergraduate, postgraduate and professional level. The model extends beyond traditional university boundaries to match industry requirements to international best practice. It is based on collaborative alliances and innovative presentation modes which will provide industry access to undergraduate and postgraduate course elements presented by a broad range of national and international academic and industry authorities. It offers the prospect for preserving the best of university ideals in higher education, for developing and maintaining programs of direct relevance to industry needs and for a structured involvement in the continuing professional development of mining engineers.

Jan 1, 1997

Now that Japan has achieved a remarkable high growth and joined the ranks of economic powers, she is required to take a stance proper to her new position toward international co- operation among Western advanced countries, economic/technical aids to Southeast Asian and Pacific LDCs, and others. As a field subject to such international cooperation programs, the development/use of coal resources has been winning increasing attention in recent years. Coal is positioned as one of promising alternative energies. With Southeast Asia plus Japan and the EEC serving as the two nucleus polar regions, total coal demand in the free world is projected to jump 37% in the year 2000 from the present level and steaming coal imports in the world, primarily destined for power generation, almost double the 1983 level. Such being the situations, Japan's tech- nologies related to coal resource development, if successfully introduced into coal-producing countries to help them boost their production, can directly lead to international cooperation that Japan is now required to fulfill. At home, however, the Japanese coal industry has been just on the wane due to various press- ing problems, such as wider differentials between overseas and domestic coal and deeper/ remorter mining. The industry was named atop in a list of the industries requiring restruct- uring at a meeting of the Economic Structure Study Committee held prior to the decision- making of the 8th coal policy, which slashed coal production planned for the last fiscal year of its life to some 10 million tons, a drop of as much as 50% from nominal output planned in the 7th policy. Under such circumstances at home and abroad, a pioneer study has been under way since fiscal 1984 as part of Japan's energy cooperation in the Pacific. The study is based on the Pacific coal flow concept hammered out by the Agency of Natural Resources and Energy of the MITI.

Jan 1, 1987

By Huafu L, Ruishi N, Hongnian Y, Qinglong Z, Yangshen S

The Dongshan terrane was first recognized in 1984 (Guo,et al., 1984, 1989) as an old continental crust block of migmatized granitic gneiss in the Southeast Coastal Hercynian-Indosinian orogen, and it was thought to have occured on Dongshan Island, which has an area of less than 100 km? Recent research work has shed much light on the geology of the Dongshan terrane.The Dongshan terrane is approximately 40-50 km wide and 380 km long, trending NE. It runs from the region of the mouth of the Ming River through Putian and Huian Counties, Amoy and Dongshan island of Fujian Province to Nanao island of Guangdong Province, bordering the southern segment of the coastal region and coastal islands of Fujian and eastern tip of Guangdong Province. The Dongshan terrane is divided from the Zhejian-Fujian Mesozoic Volcanic Mountain Chains by the Changle-Shaoan fractural zone, and its eastern boundary is covered under water in the Taiwan Straits.

Jan 1, 1990

By Cole RT

The cultural ages of man have been defined in terms of smelting and hence as a prerequisite, mining for example the iron age and the bronze age. There could be no separation of the man from his role as the technologist (miner/ smelter) for his early metal working efforts were to enhance survival. In the millenniums since, the artisan specialist developed and the technologist emerged. The process is a sort of technical natural selection. From the generalist hunter, gatherer, miner, metalworker we advanced over the centuries with great 'steps for mankind' to the series of specialists each largely intent on securing his/her technical functions from the curious assaults of other tribal members. The relevance of all this to the theme, 'Past, present and future of the Victorian mining and metallurgical industries', is simply that people have always, and will always, be the moving force in our industries. It is the effectiveness of people now and in the future that this paper addresses.

Jan 1, 1982

By R Gaze, J Horton

Block models generated with all linear interpolation algorithms contain inherent smoothing that typically results in an underestimation of grades and overestimation of tonnes in resource estimates. For mineral deposits that are anticipated to be exploited by underground mining methods excessive smoothing may result in materially misleading estimates of Ore Reserves. To account for smoothing in the open pit mining environment recoverable reserve techniques such as indicator kriging and uniform conditioning are employed to provide non-spatially located proportions of the large blocks above the cut-off grade. These models are not suitable for underground mine planning where the actual location of material above cut-off is required to design its extraction. To correct for excessive smoothing it is proposed to modify the ordinary kriged block estimates a posteriori using an affine correction with a local variance adjustment factor. The proposed methodology is demonstrated for a base metal deposit during a feasibility study.

Jan 1, 2009