Search Documents

By Williams SR

Column Flotation cannot be used indiscriminately. Based on extensive pilot plant experience at Lakefield Research, a number of limiting parameters have been identified for the application of column cell flotation. Parameters of importance are the use of wash water, flotable mineral content, pulp viscosity, type of mineral selectivity being sodght and degree of mineral liberation. The paper discusses when wash water should be used and the positioning of a column within the circuit as this is important to maintain a sound water balance for the circuit and prevent excessive circulating loads. Other areas of debate are pulp chemistry, very low and high weight recovery, for which the conventional column is a poor selection of equipment, and treatment of complex ores, where the separation of valuable minerals is more difficult than non-sulphide, sulphide mineral separation. Based on these observations, the application of column flotation must be carefully considered or can be optimised.

Jan 1, 1993

Before commencing design of a coal prepar ation plant, it is essential to have detailed information of the raw coal to be treated to- gether with a clear understanding of the products required. Prediction of raw coal size distribution, particularly the amount of fine material, is difficult and the methods employed should be large scale pilot plant studies or techniques to simulate coal degradation and shale breakdown in water. A detailed knowledge of well proven coal preparation processes and new developments allows processes and process combinations to be compared to'obtain the maximum economic recovery when using lower cost, less efficient processes within acceptable limits. Equipment should be selected bearing in mind its precise application and the location where it is installed. Plant layout should be carefully studied to minimise equipment requirements and to simplify construction. Measurement, control and automation should be an integral part of plant design in order to obtain the optimum performance of the processing equipment.

Jan 1, 1974

By Partridge AC

In order to provide a'valid description of the performance of size classifying equipment it is necessary that a standard procedure be established for testing and for the subsequent expression of results. Such a standard would permit the valid comparison of alternative equipment and may provide a basis for the prediction of performance. An Australian Standard (AS 1634-1974) has been used as the starting point for an International Standards Organisation-(ISO) working group (of which the authors are members) charged with the preparation of an ISO Standard for the expression and presentation of the results of tests on coal size classifying equipment. The approach taken is applicable to all types of sizing equipment (cyclones, screens, dedusters, etc.) and should be suitable for adoption in the minerals industry as well as by coal preparation engineers. The background to the proposed Standard, is given,including a critical review of other frequently quoted performance measures, the procedures described in the draft are discussed, and an example given.

Jan 1, 1984

By Battino S

ABSTRACT' The high gas emissions associated with coal extraction at some-Australian collieries have provided a need to investigate the methods used to predict these gas levels and the vent- ilation requirements for gas dilution. It is generally accepted that the introduction of longwall extraction in particular is associated with complex ventilation planning problems. These problems are made much more severe when the colliery introducing longwalls is already facing high gas emissions even during the development stages. A forecast of likely gas emissions during the longwall mining process indicated possible ventilation problems in maintaining the necessary ventilation levels to satisfy the statutory gas limitations for various production rates. Although there are sound principles used in world recognised methods of gas emission prediction a new approach developed from the findings of the Barbara Experimental Mine in Poland appears most suitable for Australian conditions. This has been applied to an Australian colliery preparing for longwall mining using statistical methods for air

Jan 1, 1983

By L E. Krause

This paper discusses the considerations for optimum maintenance of critical ore handling infrastructure in order to minimise the cost to the business of maintenance periods. As maintenance periods are a direct interruption to production, time is of the essence and careful management of shutdown periods is essential. The ore pass systems currently in use at Xstrata Copper û Mount Isa Copper Operations are up to 30 years old and have had significant wear over the years. The maintenance of these passes and their brows and chutes in a production situation is a challenge as it can potentially expose personnel to high risk situations in addition to the production interruptions. Some alternatives for mitigating the risk of working in ore passes including plugging and ballooning are described. Criteria are included for selecting a method for the safe entry into a given ore pass. Experience in adapting the method of ore pass plugs and some lessons learnt in the process are also discussed.

Jan 1, 2005

By Williams ID

Ore and coke of various size fractions (1 to 11 mm) were packed in a column (146 ó) and resistance to air flow measured under a range of conditions. Results have shown that layered charging results in an interface having essentially a directional structure the thickness of which is directly proportional to the coke and ore size ratio and whose flow resistance exceeds that of the coke layer many times its thickness. Friction factor - Reynolds number plots showed large positive departure from the Ergun equation for all components investigated whilst functional analysis and that in terms of bed constants, showed a strong dependency of the pressure gradient on bed properties and the actual particle size as well as the size ratio. It is also shown that pressure gradient in mixed beds follows previously reported behaviour and that a directional interface offers higher resistance to flow than a mixed interface having the same volumetric ore/coke ratio. Significance of results to practice is discussed.

Jan 1, 1975

By Olden WH

A scheme is presented whereby the complexities of design and operation of a hydraulically powered coalmine support are modelled using the finite element method. This enables predictions to be made of the interaction of the support with its environment in a variety of operating conditions. The model is a two dimensional representation. The modelling scheme was applied in two case studies. In the first, the performance of a four leg support was uprated by increasing the front leg force. The finite element model enabled changes in overall support performance to be verified. In the second case study, the change in lateral force developed by a two leg support was assessed with changes in support operating height and floor foundation stiffness. The modelling scheme is capable of further development with the possibility of extending the model into three dimensions and the addition of control elements that would enable an actual mining sequence to be Represented.

Jan 1, 1992

Mining is taking place at increasing depths of cover on the Southern Coalfield beneath pre- dominantly massive sandstone strata. Within the next twenty years, there will be longwall mining at depths greater than 600 m. As the Sydney Metropolitan area continues to expand and as coal mining approaches these urban areas subsidence will continue to become an increas- ingly important aspect of coal mining research. Investigations commenced in the mid 1960's and it is now possible to predict subsidence in the Southern Coalfield with reasonable con- fidence. The work is showing that the characteristics of the subsidence troughs over the deeper mining at Appin differ from the characteristics of mine subsidence at less cover. The longwall mining at Appin Colliery has resulted in a maximum measured subsidence of 730 mm. The maximum strains were small because of the large radii of curvature of the subsidence profiles. There was no damage to any of the buildings in the township of Appin.

Jan 1, 1981

By Kokubu H, Moro-Oka A

Gaseous desulphurization from hot metal- lurgical slags containing sulphur mainly as sulphide and(or) sulphate was measured under `low at four different oxygen pressures. The total gas rate was from 1.7 to 2,8 litre/min. Crushed slag samples weighing 2 to 12 g were used for the experiments. The amount of SO2 gas evolved from samples kept at 15500 was rieasured over tires ranging from 20 to 300 min. The gaseous desulphurization rate of sul- phide sulphur becomes high as the oxygen part- ial pressure is increased, while that of sul- phate sulphur is high under low oxygen pressure. The effect of basicity on the desulphurization rate of sulphide sulphur in oxygen atmospheres is not obvious in the range of basicity from one to three. Changes in the ratio of sulphide to sulphate sulphur during the run in oxygen axe analysed. Desulphurization reactions and the rate controlling steps are discussed. De- sulphurization phenomena can be explained by inte.-¦ucia.l chemical reaction rate control.

Jan 1, 1980

The paper describes a computer model developed within the State Electricity Commis- sion of Victoria for use in open cut planning. The purpose of the model is to simulate all the typical occurrences in, and influences on, the coal supply and overburden disposal systems in order to be able to assess their performance. The model incorporates much of the long term and day-to-day operations planning logic required for the allocation of resources within an open cut. This logic takes account of power station demands, bunker stocks, plant and crew availability, the balance of reserves between dredgers, planned maintenance, etc. The perfor- mance of plant within the system is simulated using random selections from statistical distri- butions of Time to Failure and Time of Failure for each plant item. The application of the model in selecting a suitable bunker capacity in a notional open cut development is described to illustrate the potential of the model in optimising plant selection.

Jan 1, 1982

By Burnett C. C H

GEMNet, (Grade Estimation using Mapping Networks), is a grade/reserve estimation software system that uses the artificial intelligence technique known as neural networks to perform reserve estimates from both two- and three-dimensional data samples from a mineral deposit. The system is the result of research carried out over the past three years into the feasibility of using neural networks for reserve estimation at the AIMS Research Unit in the Department of Mineral Resources Engineering at the University of Nottingham. This paper describes the architecture of the GEMNet system including details of the neural network components of the system. The performance of the GEMNet system is then compared to several other widely used reserve estimation techniques on two reserve estimation examples. The results produced by the GEMNet system compare favourably with more conventional estimation techniques, but require fewer assumptions to be made about the form of the data used, and do not require the use of complex mathematical modelling.

Jan 1, 1995

Gold mineralisation at Wapolu lies within an exposed arcuate zone at the decollement contact between a basement dome of high grade metamorphics and an overlying ophiolite sequence. This contact was originally a thrust fault which has since become a decollement zone for gravity sliding in association with basement doming. Hydrothermal models for the gold mineralisation postulate an epithermal system in which fluids were channelled up the decollement with boiling of those fluids causing hydrothermal brecciation and subsequent gold deposition. The alteration assemblages, fluid inclusion data and geochemistry indicate that the upper levels of the system are exposed.

Jan 1, 1987

This paper outlines the mechanism of Stress Corrosion Cracking (SCC) and how it can cause premature failure of rock bolts. SCC occurs due to the progressive development and growth of cracks in the surface of a metal, and it is caused by the combined effects of stress and a corrosive environment affecting susceptible metals and alloys. It can occur in most metals including stainless steel. It is not a new phenomenon, but its effect on rock bolts has only been recognised recently.Rock bolt failures caused by SCC appear to be brittle failures which occur at less than the ultimate tensile strength of the bolt. In the mining industry, SCC failures of rock bolts can occur a few months, or after many years of exposure to stress and a corrosive environment. If SCC of rock bolts is suspected, then the rock bolts should be examined by a metallurgist, and steps should be taken to reduce the problem.

Jan 1, 1998

By Y Gu

Based on the mode of occurrence, gold is classified into three categories: microscopic gold, submicroscopic gold and surface-bound gold. Microscopic gold, or visible gold, refers to gold minerals in which Au occurs in a substantial amount, such as native gold and electrum. Submicroscopic gold, ie invisible gold, refers to gold contained in the structure of other minerals (mainly sulfides) in minor to trace amounts. Surface gold is the gold that was adsorbed onto the surface of other minerals during mineralisation and subsequent oxidation or metallurgical processing. Gold mineralogy has a significant impact on its extractive metallurgy. Gold process mineralogy helps address problems related to gold ore processing. It is widely used as a predictive and troubleshooting tool in gold ore processing, and provides useful information on process selection, flow sheet development, recovery improvement and reagent consumption optimisation. This paper will begin with the classification of gold ores, and will focus on gold mineralogy and how it impacts extractive metallurgy through case studies.

Jan 1, 2008

Facies associations in the Okiduse Volcanics, woodlark island, suggest that two major volcanic centres erupted synchronously during the Middle Miocene. These centres are referred to as the Watou Mountain Eruptive Centre and the Uvarakoi Caldera. The Watou Mountain Eruptive Centre, centred on Boganuse Mountain in the Okiduse Range, was a typical, moderate-sized composite volcano (or stratovolcano). The seq-uence is readily divisible into lava (Boganuse lava unit), breccia (Nikuben breccia unit) and epiclastic (Talpas sandstone unit) dominant facies, typical of composite volcanoes. These facies girdle Boganuse Mountain and they are interpreted to represent vent, cone forming and ring plain associat-ions, respectively. These facies indicate a reconstructed volcano of approximately 1,700m height with a basal diameter of 7km. The presence of limited exposures of intrusive associated with the vent facies (Kuike'beimmicrodiorite) suggests that the volcano is only partially dissected. The Uvarakoi Caldera is a felsic volcanic system contrasting with the mafic Watou Mountain centre.

Jan 1, 1994

By Elliot B. J

Cobalt is principally produced by hydrometallurgical means from the copper-cobalt ores of Zambia and Zaire. In addition cobalt is commonly found in minor quantities in association with nickel and copper-nickel orebodies. Generally the level of cobalt common to these latter orebodies does not warrant separate processing unless the metal price reaches levels last achieved in 1979 and 1980. For pyrometallurgical processing the distribution of cobalt and the factors which affect the distribution of cobalt between matte and slag are not well understood. A limited amount of fundamental research has been completed on cobalt distribution both for simple oxide and matte systems. The paper briefly reviews the relevant literature on theoretical aspects of cobalt distribution between metal and slag and the deportment of cobalt in sulphide smelting circuits. The deportment of cobalt in the Kalgoorlie Nickel Smelter circuit is critically analysed and areas where recovery improvements may be achieved are highlighted.

Jan 1, 1989

The Permo-Triassic Bowen Basin developed during the final stages of the Tasman Orogenic Phase in eastern Australia. The basin has considerable economic value as a source of coal, natural gas and precious metals. The basin, which is of controversial origin, is preserved as a north-south trending, asymmetrical syncline bounded in places by faults. It is here interpreted as a retroarc foreland basin which developed on the landward (west) side of a continental arc associated with continent-ocean plate convergence. Initiation of the basin occurred via back-arc extension in Early Permian times, coincident with a phase of talc-alkaline arc volcanism. Early Permian, mostly marine sedimentation gave away to extensive coastal and alluvial plain depositional systems in Late Permian times, coincident with a resurgence of arc volcanism. Triassic sedimentation was almost entirely alluvial and coeval with westward propagation of thrust sheets from the eastern basin margin. Compressive tectonics climaxed in Middle to Late Triassic times, terminating sediment accumulation and uplifting the entire area.

Jan 1, 1990

By Glastonbury J. R

The kinetics of the direct chlorination of, zircon in the presence of carbon was studied at temperatures between 9000C and 12000 C. From the experimental data it is prop- osed that the most likely mechanism for metal oxide (MeO2) chlorination is as follows: At I Surfaceon zMeO2+ZMeCl - MeOC12 (1) At Carbon MeOC12+C+Cl MeC14+CO (2) Surface It.is envisaged that this type of mechan- ism would occur for both the zirconium and, silicon. constituents of the ore. In the above mechanism; the surface re- actions appear to be fast and not rate controll- ing. In a carbon surface deficient bed the diff- usion of oxychloride intermediate through the boundary layer to the carbon surface becomes the rate controlling step. In a zircon surface deficient bed the diffusion of oxychloride away from the zircon surface controls the reaction. This postulated mechanism can be used to ex-, plain the observed experimental effects.

Jan 1, 1973

The provision of electrical power is an important consideration in project development. The first step to be taken in this area is to assess the power requirements of the project. The alternatives of laking a supply from a power authority or providing local generation can then be considered. This requires additional defmition of the probable characteristics of the supply.The availability of authority power in Australia is limited by the extent of the state power grids. Recent developments now allow these grids to be extended and their load capacity increased to meet major load increases at less cost than was previously possible.The options for local generation include diesel, gas turbine, steam, hydro, solar and wind, each having its particular performance characteristics and costs. The choice of fuel for diesel, gas turbine, and steam plant likewise involves consideration of a range of factors. The arrangements adopted for five recent Australian remote development projects indicate how some of these aspects influence the decision on power supply.

Jan 1, 1990

Conventionally, a combined system consist- ing of a dry or wet pulverizer and kneading mac- hine is applied to the pretreatment of fine mat- erials for agglomeration, especially for pellet- izing. However, treatment cannot be expected to be satisfactory owing to the complexities of the process. A new process was developed to over- come the defects inherent in the conventional process. This new process treats certain fine materials having a moisture content somewhat lower than that suitable for pelletizing in a ball or rod mill. The mill is of special de- sign in which grinding and strong kneading are performed to give an extremely homogeneous ball- ing material with appropriate size distribution and pelletizing characteristics. The most serious problem in this process is the choking of sticky materials in the mill. A specially designed rubber lining was installed in the mill to overcome this trouble. This paper presents actual results from our iron ore pelletizing plant relating to the pelletization of other fine materials.

Jan 1, 1974