Search Documents

The value of water is defined by its marginal utility. Challenges arise where the marginal utility is difficult to estimate. Therefore, when two or more interested parties wish to access water and they cannot use commensurate units for marginal utility; other means of value comparison must be sought. It is asserted here that sustainability principles can be used to guide this valuation if this is supported by a transparent decision framework. This paper proposes that the ICMM sustainable development principles provide appropriate guidance. In addition, a generic framework for decision making is suggested as a complement. Indicators of water management are recognised widely as an integral part of the accountability of minerals companies towards meeting sustainability goals. Less widely recognised are the ways in which sustainability principles can be used to guide decisions on water management which demonstrate growing awareness of its value. This paper illustrates the use of this logic in water issues associated with global sustainability challenges. It then goes on to demonstrate, using examples, that these links exist at all levels of the minerals industry and that indicators of this type are potentially as powerful as those currently being used. The reason for this is that the path from cause to effect is transparent and direct.

Jan 1, 2006

The methods employed in dressing 'the tin ore up to the required percentage of purity depend mainly on the type of ore crushed.These may be briefly divided into two distinct classes-viz., q, free: milling ore and a complex milling ore. In the former the ore is practically free from the common metallic sulphides, such as pyrites, mispickel, blende, galena, etc., and 1!' clean concentrate of 70 per cent metallic tin can be directly obtained in one continuous act of concentration; in the latter, however, in order to get a good extraction, it is only advisable to primarily concentrate up to 30 to 40 per cent. tin oxide, the rest being the sulphides of the metals. This concentrate is then roasted, re-ground, and re-concentrated up to 70 per cent. metallic tin on a separate set of tables.In the complex milling ore the tin is intermixed very closely with the sulphides, so that it becomes necessary to collect all the mineral present in order to obtain clean tailings. Stamp mills are the most popular machines for the primary crushing in the district, but whether they are invariably the best for the purpose is rather an open question. No doubt for some of the very tough chloritic ores they are the most efficient, but for a brittle quartzose ore, such as the free milling proposition usually is, the writer thinks Oornish rolls would well hold their own, especially when the tin occurs coarse, as is so often the case with this class of ore. Of course, the great drawback to stamps is the excessive quantity of tin slimed and slime tin is one of the problems of tin-dressing-while rolls give...

Jan 1, 1907

By D V. Boger

The use of chemical additives to initiate such processes as particulate separation through flotation or dewatering through flocculation, is common in the mining industry. The dosing of additives is none the less poorly controlled from a process control viewpoint and it is perhaps fortuitous that over-dosing or misuse of chemicals is rarely catastrophic to the production cycle. In many cases, such events would go undetected if it were not for economic considerations. Recently, the advent of orebodies with finer mineral disseminations and the push for greater efficiencies in both production and tailing disposal have resulted in the need for greater control of the dosing and utilisation of chemical additives. The need to grind at higher pulp densities and to finer sizes and to dewater to higher solid contents are but two examples that require a more stringent understanding of the true role of additives in controlling the rheology of suspensions and the influence of additives on the surface chemistry of particles. The inter-relationship between the surface chemistry of particles and the role of additives in controlling suspension rheology is now well understood for systems in which the average particle shape in the mixture is spherical or close to spherical. Luckily, this is the case for a large number of systems in the mining industry and the true role of typical additives in these systems will be explored. Difficulties arise for suspensions containing clays or other platey or needle shaped minerals and in many cases, quite small quantities of platey minerals dominate the rheology of suspensions. The role of additives in controlling the rheology of asymmetric particle systems is more complex but the effect of the additive in changing particle alignment in solution is the key to understanding suspension behaviour. The manipulation of the rheology of asymmetric particle systems will also be explored.

Jan 1, 1998

By Leigh G, Gottleb G, Wilkie G

The estimation of particle liberation is important in the study of mineral concentration. With simple systems, where the densities of the components are low, the liberation can be studied directly by density fractionation. For most practical systems, and particularly for the dense, complex sulphides, the only method known is by measurement in polished section. There are two major difficulties with such measurements. Firstly, the measurements themselves are difficult and considerable care is needed before reproducible results can be achieved. Secondly, a well known stereological problem arises which gives the estimates an inherent bias. The paper discusses both aspects of the problem. The practical features of measurement are treated in detail and a method described which has been developed and proven to give reproducible estimates of the liberation in the section. This discussion relates to automated measurements by QEM*SEM and presents a way of estimating the confidence limits within which measurements lie. Comparisons are shown between measurements made by the traditional manual optical technique and automated equipment. Stereological reconstruction is also discussed briefly. Several methods have been presented in the literature but all are complex and none is yet widely accepted. Area measurements are less biased than linear estimates so a practical approach is to use area measurements in uncorrected form. The topic is still being actively researched so it is expected that one method will soon emerge as the standard technique.

Jan 1, 1993

By Bowmaker MD

Zinc and lead sulphide flotation con centrates containing from 0.02 to 0.20% Cd are roasted on an updraught sinter machine at the Cockle Creek Works of Sulphide Corp- oration Pty. Limited to provide sinter for simultaneous smelting of zinc and lead in an Imperial Smelting Furnace (I.S.F.). The major portion (about 85%) of cad- mium in concentrate feed to the Sinter Plant is eliminated with sinter fume and is rec- overed by weak acid leaching in the Cadmium Plant'followed by counter-current decantat- ion, ion exchange concentration, precipitat- ion of cadmium sponge and partial refining to caustic refined cadmium metal. Cadmium not eliminated during sintering is volatilised in the I.S.F. and subsequently recovered as zinc alloy by distillation in the zinc ref- ining columns of the Zinc Refluxer. The partially refined cadmium metal and cadmium- zinc alloy are blended as feed to the cadm- ium refining column where separation and recovery of cadmium is effected. Condensate from the column is further refined under caustic soda flux and cast into anode shapes. Production is 200 t.p.a. at 85% recovery of cadmium in concentrates. Emphasis is placed on changes from the practice described by Baker and Munro (1965) and upon operation

Jan 1, 1972

DIVERSITY There are plenty of examples to show that diversity has been the fundamental downfall of many organisations, particularly when you consider the international position. What about core business, the return of companies to key competence directions and market focus. The stockmarket for instance defines groups and companies in key groups of core business. The expectation is that companies toe the line and do not diversify across their areas of defined expertise. In essence, the market has given notice that the requirements are to focus and stick to our core business. So what right does the conference have to suggest that diversity is the key to prosperity. Hasn't the organiser read the book, studied the history, listened to the market - obviously not. Have they got it wrong, My feeling and belief is no - the organisers have got it right. However, the matter is not as simple as first perceived. What is Diversity, or Diversification as I would prefer? Is it a product position? Is it a geographic position? Is it an expansion or change in services offered? Does a gold mining company diversify into copper or diamonds or aluminium or nickel? Does a gold miner in Australia diversify into China or Kazakhstan or West Africa? How do the two relate? They don't. A successful company will always possess a 'core competence' not so much a 'core business'. The best example of this is the service company extraordinaire - McDonalds. They don't sell hamburgers or french fries, they sell a service, a convenience, a lifestyle. The core business is hamburgers and if McDonalds were to diversify further into new styles of hamburgers, I suggest to you they would fail. But if McDonalds were to diversify into other products based on their 'core competence', provision of service, then I would suggest to you they would be very successful. The service procedure, service machine, service system, the formula, stava the rnnetant the nrnrlnrte -

Jan 1, 1996

By J A. Rumball

Measuring cyanide in the leach liquors associated with high copper and/or sulfide ores is a non-trivial exercise. It is well known that copper complexes with cyanide and reduces the amount of cyanide available for gold leaching. What is not so well known is that the rhodanine end point overestimates the amount of cyanide available for leaching in the presence of copper. Sulfide ions also interfere with a rhodanine end point titration, although this is less of a problem as the black silver sulfide precipitate formed clearly indicates to the operator that something is wrong. Thiosulfate, which forms readily from the alkaline oxidation of sulfides, causes an overestimation of the cyanide available for leaching due to the formation of Ag(S2O3)-. The net result of these observations is that rhodanine is rarely of value as an end point indicator in complex solutions. It generally overestimates the amount of cyanide available, providing plant metallurgists with a false sense of security. Potentiometric titrations are generally much more capable of accurately measuring cyanide in complex solutions. The interfering effect of copper can be resolved and it is even possible to estimate the copper concentration using the inflexions associated with the titration of CN- + Cu(CN)43- versus Cu(CN)32-. Using the potentiometric method sulfide ions can be determined before the cyanide measurement is made due to the formation of AgS2, although the electrode will foul with repeated measurements. Thiosulfate can also be distinguished from cyanide with a potentiometric titration. Rhodanine and potentiometric titrations are both affected by the pH of the liquor. At pH 9.2 half the cyanide will be present as CN- and half as HCN(aq) with only the CN- being titratable. This does not hold in the presence of a buffer active around pH 9. In the presence of sufficient buffer, both the CN- and HCN(aq) are titrated. Ca(OH)+ may buffer the pH when large amounts of lime have been added.

Jan 1, 2007

The traditional concept of optimum drill and blast is that it is achieved when ore is produced at the lowest unit cost and, because of the complexities of most mining operations, represents a band which extends either side of an overall cost m

Jan 1, 1998

By Quan P. M

The great advances made in the application of solvent extraction to the recovery of copper from low grade ore sources over the past 15 to 20 years are well known. Solvent extraction is an essential step in the recovery and purification of copper from dilute sulphate leach solutions by which some one million tonnes of copper are now electrowon annually. A reagent is also available for the selective recovery of copper from chloride leach solutions and this may hold the key to the processing of complex sulphide ore concentrates. By comparison, the use of solvent extraction in the recovery and processing of zinc has as yet found little favour and is confined to only a few specific and comparatively small applications. This is despite the ready availability of a large number of low grade zinc sources and zinc-bearing wastes and residues. It is suggested that this difference is due in large part to the absence of suitable reagents having the particular features required to enable them to fit into a solvent extraction - electrowinning based process for zinc. Ideally, for the recovery of zinc from dilute sulphate solution, an extractant should operate on a proton exchange principle and be strong for zinc in the same way that o-hydroxyaryloxime reagents are strong towards copper. It should load efficiently with zinc at the pH of typical sulphate feed streams without the need for neutralisation and yet be stripped efficiently by spent zinc electrolyte. Another factor of major importance for many applications, however, is that it should be highly selective for zinc over ferric iron. These features have now been realised in a development extractant DS5846, which is a formulation of a novel class of reagent currently under investigation by Zeneca Specialties. The properties of this reagent are described with respect to selectivity, isotherms and how they compare with phosphoric and thiophosphoric acids that have been previously proposed for the extraction of zinc. For the recovery of zinc from concentrated chloride solutions a solvating or neutral donor type of extractant is required which again should ideally have high selectivity for zinc over a number of other metals, particularly iron. The new reagent Acorga ZNX50 is based on a formulation of a novel class of compound developed specifically for this purpose. It gives efficient extraction of zinc from feed solutions that are four to six molar in chloride ion but is readily stripped at 60 - 65¦C using either water, dilute brine, or spent zinc chloride electrolyte. The reagent is highly selective for zinc over iron and a range of other metals including cadmium, arsenic, lead and magnesium.

Jan 1, 1993

Geophysics is playing an increasingly important role in the exploration industry. In the soft rock scene the application of seismic techniques is basically mandatory prior to any drilling program. Simply, this is because, in a majority of situations, the seismic method is ideally suited to mapping accurately relatively flat lying strata and displaying structures that may host oil or gas. It is worth stressing that seismic methods do not delineate oil or gas but they map well in two or three dimensions. In the base metal arena, geophysical methods used are generally focussed on direct detection methods with the mapping application not often used except in potential fields (magnetics and gravity). The success rate in the last decade has not been good but this does not only apply to the application of geophysics; it really applies across the board of exploration techniques. Both geological and geochemical exploration have not had a success rate commensurate with the funds injected. Basically in the last ten years we have failed as explorers! As explorers we have been negligent in mapping. As geoscientists we have let the basic mapping and observation skills diminish û the old adage æboots on the groundÆ is still applicable but are we doing enough of it? The answer is clearly no. As explorers the huge burden of bureaucracy, eg Government Acts û local, state and federal, safety compliance, environmental compliance, etc has reduced the ægeologicalÆ time dramatically. This has culminated in an over-reliance on quick fix solutions, eg spot the bump geophysics or geochemistry. This obviously simplistic scenario is arguable but there is no doubt in the geoscientific areas we have failed in the last decade to provide adequate geoscientific maps to assist in exploration. This failure could partially be responsible for the current demise of the industry resulting in a reduction in exploration dollars and, hence, people. This trend is seen acutely in the geophysical area where the head count in comparison with the geological fraternity is low. Other trends during this downturn are inevitable as explorers maximise the use of the dollar in exploration and diminish spending on advances in geophysics. Improvements are being seen however in geophysical equipment, although it is considered that the main improvement will be in the interpretation of data. Specifically, the trend will be towards integrating geophysical data into geological, geochemical and spatial data sets producing quality interpretation and providing low risk drill targets. Examples of the current trends in hardware and future directions are discussed below. In interpretive schemes there are very few examples of integrated interpretation but the possible trends will be discussed with limited examples.

Jan 1, 2000

By P Hawkes

Within the mining industry computers have made their most significant impact with 3D design, visualisation and resource modelling/ optimisation. Recently, the application of computers to data gathering and accounting functions has also started to reap benefits. These two areas of application cover the beginning and end of the mining process. There has been limited use of computers on the middle section, the actual mining process. This is interesting when considering the relative proportion of overall mining costs that this section produces. There is a certain amount of irony in the lack of mining application software for developing accurate budgets compared to the systems/software then used to review performance against budget. Computers have been used extensively in the manufacturing industry to design, model and simulate the manufacturing process. This has not been extended to the mining process. But, we all strive to have an open pit that replicates a manufacturing plant û smooth, efficient, optimal production. If we could model mining operations with the confidence of plastic box makers we would reduce risk by an order of magnitude, improve planning and focus on value drivers. Cost û benefit analysis would be easy. The extrapolation of manufacturing to mining process models is difficult. The variables in the manufacturing process are fewer in number, have low volatility and are highly predictable. The time between a box falling on a conveyor belt and falling off is very consistent. Mining is quite the opposite. It has large numbers of variables, some of which are unpredictable and volatile. The time to fill an excavator bucket could vary by 30 per cent and the frequency distribution is unlikely to be a mathematically simple normal distribution. Further, each of these variables can be distorted by one-another û they are interrelated. The mining process is a disjointed flow of parcels whereas manufacturing is a controlled continuous feed. A loaded truck might join a ramp and follow a slow water cart up. This is the equivalent of a localised voltage drop on equipment in a manufacturing plant. The manufacturing plant is quite likely to rapidly recover to full capacity. Whereas the slow truck might throw the mining fleet cycle out of balance for hours û trucks queuing at the ROM bin and so on. A mining process simulation has been created that addresses these mining variable issues to produce a highly accurate model of the open pit mining process. The number of uses for such a model is growing rapidly as it is being utilised for a variety of projects within the industry. This paper discusses the need for and application of mining process models.

Jan 1, 2003

The Electricity Commission of New South Wales is the largest single user of coal in the State, burning some 8.5 million tonnes during 1972-73. This coal is converted in power stations into electrical energy which is then distributed throughout the State and supplies the electricity requirements of 99% of users in New South Wales. Barring any major change in energy consumption growth, or change in the current mode of power generation, the consumption of coal by the Commission is estimated to have a doubling period of from 10 to 14 years. Coal is used to generate up to 87% of the electrical energy sold, the balance being obtained from hydro gen- eration, mainly in the Snowy Mountains, and, to a much smaller extent, from diesel generation at Broken Hill. A very large proportion of this coal is consumed in pulverised fuel boilers in the Commission's power stations, located mainly on the various coalfields of New South Wales. Coal supplies are drawn from a large number of mines, some owned or controlled by the Commission, others being owned by public companies. The coals used, originate from at least ten different seams located in the northern, western and southern coalfields of New South Wales, and therefore have a wide variety of properties and characteristics. To ensure an adequate fuel supply well into the future, the Commission is continuously engaged in coal prospecting in various areas. Bore data is used in assessing coal reserves and is also the basis of economic studies for their possible future exploitation. The numerous coal cores obtained during drilling operations are carefully tested and analysed in order to assess their suitability for power generation purposes, and to provide data for the design and operation of boiler plant using these coals. In existing power stations coal deliveries are systematically sampled and tested for quality control, for pay- ment of purchases based upon certain quality parameters and to check for any possible plant operating or main- tenance problems that might arise from the use of the particular coals. Almost all the properties of coal that may be necessary in the Commission's work are obtained using standard testing procedures carried out by the Commission's chemists, in laboratories located at the various power stations or at its Central Laboratories in Pyrmont. Where specialised analysis or testing is required, this is ordinarily undertaken on a commercial basis by outside bodies, expert in the particular field. The significance of the various properties of the coal for use in p.f. boilers is outlined and related to their proper application to boiler plant design and to plant operation.

Jan 1, 1975

By Hinchliffe WD, Griffin A

The desorption of gold from activated carbon is promoted by adding organic solvents to aqueous cyanide solutions. At 65-80¦ the elution of gold is fast and is not affected by water quality. The Micron Procedure involves pretreatment of the loaded carbon with NaCN/NaOH followed by elution with methanol vapour and condensate. Carbon is packed into a column above the distillation pot and acts as a fractionating column. Recovery of the methanol condensate leaves a methanol free concentrated gold solution and carbon containing

Jan 1, 1984

A failure criterion for coal is proposed in which a distinction is made between brittle and "pseudo-ductile" failure. This criterion is then used in the development of new equations for coal pillar strength, including a transition from brittle fracture to pseudo-ductile yielding. In addition, equations are obtained which allow the äritical minimum pillar dimensions to be calculated to avoid "catastrophic" and "ultimate failure". The use of these formulae is then demonstrated by comparing the results with pillar case histories derived from the literature.

Jan 1, 1986

By Upfold RW, Nguyen VU

The extraction and utilisation of metals and materials is the basis of modern civilisation, and will remain so for many decades, Traditional metals are facing some challenges and research is needed in specific areas, to improve metal extraction processes, to develop processes for newer metals and minerals, and to develop new applications, The shortage of metallurgists now becoming apparent in Australia is a further significant problem that needs urgent attention, and much more publicity is required for the Mineral Industry, as well as for the utilisation Industries,

Jan 1, 1986

Reservoir Engineering has developed into an art. One phase of this art is forecasting the futi. perf ormance of oil and gas reservoirs for property valuations. A discussion of the necessity for oil property valuation isgiven. A brief 'discussion of the four most common methods is included and the engineering method is explained in more detail. As an example of oil property valuations, a producing oil lease in Shackelford County, Texas, USA is evaluated.' The recommendations and conclusions arrived at frun the results obtained are presented.

Jan 1, 1962

The discovery of copper and nickel sulphides in the Riwaka Complex in 1967 led to considerable exploration activity by a number of companies. Various exploration techniques used by these companies are summarised and discussed. Activity of these companies shows that mineralisation is mainly confined to the southern, ultramafic section of the Riwaka Complex where geological mapping recognised sixteen units within, or associated with the Riwaka Complex. Significant pyrrhotite, pentlandite chalcopyrite mineralisation is restricted to biotite feldspar pyroxenites and to clinopyroxenite units. Lesser and more erratically distributed pyrite chalcopyrite pyrrhotite mineralisation occurs in poikilitic pyroxene hornblendites, melanocratic gabbros, and in marginal diorite lenses. It is suggested that a linear belt of layered ultramafic and mafic rocks described in Fiordland by Williams (1974) may be a southern extension of the Riwaka Complex. The Riwaka Complex has been classified as belonging to the Picritic subtype, (Tholeiitic suite), of Naldrett and Cabri, (1976), and as such it is concluded that it exhibits substantial potential for the discovery of economic copper and nickel deposits. It is considered that the complex is a multiphase differentiated intrusion emplaced in a major tensional fracture zone that developed in a relatively stable tectonic environment, namely a succession of middle Paleozoic shallow water shelf sediments. Based on sparse available evidence it is suggested that the Riwaka Complex was intruded in the lower to middle Permian. It is further suggested that the tensional fracturing was initiated by the onset of subduction process which were responsible for the development of the Permian volcanic arcs and ophiolite belt in the north west Nelson area.

Jan 1, 1977

By Samyguin VD, Filippov LO

The aim of this paper is to emphasise the importance of knowing of the rate of the elementary flotation acts (EFA) - attachment and detachment. By studying the simplest linear model notion of the column flotation, the results of the nonlinear simulaton of flotation separation in the column with lengthwise upward mixing show two principal different types of separative mass-transfer in the column. The first is, the case of a small EFA intensity, almost without the detachment. The second is, the case of a big EFA rate, when the process is close to a local attachment-detachment equilibrium. There is also an attempt to estimate the EFA rate for three different kinds of quartz particles, floated by cation collector in the laboratory column apparatus.

Jan 1, 1993

By B F. J Kelly

Multiple-point simulation is a family of methods used to generate conditional facies simulations that present the same spatial dependence as a user-defined training image. The main advantage of using a training image is the easy integration of geological concepts in numerical subsurface models. The strength of multiple-point methods is that it allows making the best use of geological expertise when data are too sparse for inferring a model of spatial continuity. However, despite being appealing to geologists, the multiple-point methods are often not used in practice due to the difficulty of building complex 3D training images that contain realistic features.A new framework for multiple-point simulation is presented that involves small and simple training images. The main idea is to use random transformations to expand the range of structures available in the simple training image. The training image is not regarded any more as a global conceptual geological model, but rather a basic structural element of the subsurface. Complex geological structures are obtained, whose spatial structure can be parameterised by adjusting the statistics of the random transformations, based on field data or geological context. In most cases, such parameterisation is possible by adjusting two numbers only. One advantage is that the training images are so simple that they can be easily built even in 3D. The method allows building 3D models that reproduce shapes corresponding to a desired prior geological concept and are in phase with different types of field observations, such as orientation, facies or geophysical measurements. The flexibility of the approach allows for naturally integrating different types of data. This is demonstrated on an example involving seismic data assimilation. Examples where complex 3D folded structures are built from a simple training image and a few orientation data are shown.

Sep 26, 2011

By A G. Thompson, E Villaescusa, D Howard

The Western Australian School of Mines (WASM) has developed a facility for the static testing of full-scale ground support elements (Morton et al, 2007). The test facility consists of several stiff steel frames used to support the sample and a screw feed jack is used to load the sample. A large-scale punch test method has been developed to load various shotcrete configurations. The shotcrete is sprayed on to a rock substrate containing a centrally located circular disc. The rock and shotcrete sample is placed on to the sample frame and restrained on all sides. The circular disc is displaced at a constant rate by the screw feed jack which in turn loads the sample. Instrumentation measures the displacement and the load being applied to the sample through the loading disc. The testing method is described in detail and the results from the testing program are presented. The results show that it is possible through laboratory testing to simulate some of the mechanisms of shotcrete support reactions better than conventional beam and panel tests.

Jan 1, 2008