Search Documents

By Q-c Li, G-l Gao

Cyanided tailings produced by gold processing operations may cause environmental problems, because they contain pollutants such as arsenic, sulfur and cyanide compounds. Moreover, tailings containing economic metals such as Au, Ag, Cu, Pb and Zn, are potentially valuable resources. In this article, cyanided tailings are catalytically oxidised by nitric acid in the presence of air or oxygen. The resulting solids may be leached to recover Au and Ag. The solution can be used to prepare ferric sulfate or iron pigment. Gases released in the reactions were recycled and reused by oxidation and absorption. All of these greatly improve metal recovery and the reuse prospects of cyanided tailings. Under the following conditions where the initial temperature of oxidation is 80¦C; initial concentration of nitric acid is 30 per cent (by weight); feed proportion (nitric acid to cyanide tailings mass ratio) is 3:1 and reaction time is two hours, the conversion ratio of cyanided tailings is 90.06 per cent. At the same time pyrite in the cyanided tailings is oxidised effectively, gold recovery is as high as 92.3 per cent and nitric acid loss per cycle is only five per cent because of NOx recovery.

Jan 1, 2007

Using normal low pressure filtration methods for the dewatering of fine china clays, the best that can be achieved is cakes with about 30% moisture. In order to get the moisture levels down to acceptable levels the traditional method used is thermal drying, which is both costly and dust creating. It was to improve this process that ECC International embarked upon a programme of development of filtration equipment using high pressure to achieve significantly lower moisture levels. This development work investigated several design philosophies and culminated in the production of two quite different solutions. The High Pressure Plate Press uses round plates / chambers of one metre diameter and a filtration pressure of 70 bar. This press is fully automatic and produces a surface dry cake that has sufficient plasticity for the further processing that is required on specific qualities of china clay. The TUBE PRESS on the other hand uses a unique design configuration and operates at a filtration pressure of 100 or 140 bar, depending upon the model. The TUBE PRESS produces a brittle, surface dry cake that is easy to handle and a filtrate that is usually crystal clear. The TUBE PRESS achieves a much higher degree of separation than is possible with conventional equipment, which is particularly important if the filtrate is the product. Over the past 15 years plants incorporating both HP Plate Presses and TUBE PRESSES have been installed in the china clay operations of ECC International and are giving excellent trouble free service. The TUBE PRESS has also proved to be extremely versatile, effectively dewatering a wide range of fine particled slurries, in a number of diverse industries.

Jan 1, 1989

By Turco E, Pelizza S, Castellani F, Stanganelli V

Excavation are in progress for the building of tunnels of the waterworks in West Campania (Naples). The works afferent to part II envisage tunnelling through a miocenic clay formation over consolidated by two tunnels whose sections are respectively 50 and 10m2. Tunnel blasting is carried out by mechanical means. An excavator is used in the big tunnel, whereas in the small tunnel a roadheader machine is used for a short tract and a mechanized shield is used over a long stretch. The tunnel feature complex problems regarding stability. This is particularly so for the big tunnel whose face appears unstable. For this reason the clay on the face is sistematically bolted by means of 3-metre and 12-metre bolts. This prevent the use of a TBM for tunnel Excavation.

Jan 1, 1987

By Leigh J. H

A history is given of the dust control techniques developed and applied by the mining companies at Broken Hill. A history of the regeneration works undertaken since 1936 is out- lined. Particular emphasis is placed on the stabilization of mine residue dumps which are located throughout a belt of mining leases in the middle of the city and which began in 1937. The establishment of vegetation for dust control techniques is discussed in detail and a case study is given of the successful revegetation of the sides of a 650 metre long, 350 metre wide and 35 metre high residue dump.

Jan 1, 1976

By Thuli AJ

Copper concentrate from Bougainville's copper mine located on the west slope of the Crown Prince Range on Bougainville island, is pumped 27 km to the filter and drying plant at Anewa Bay for preparation and storage prior to shipment to overseas customers. Prior to shipment the thickened concentrate slurry is passed through a test loop to check that its consistency and pH are acceptable for transportation through the main pipe line. The Bougainville pipe line is unique since it is the world's first copper concentrate system. where slurry is pumped an appreciable distance against a high head,

Jan 1, 1975

By Hyde L. J

Blasting is one of the available technologies to be employed in underground excavation systems. In many instances it can be the only technology which is suitable. The recent moves towards more mechanised working systems is resulting in a reduced awareness of new blasting practices and technologies on the part of many excavation engineers. Recent developments in blasting systems can be utilised to significantly improve operating efficiency, reduce total cycle times, better comply with regional environmental constraints and reduce the total cost of underground excavation. Blasting is and will remain, a very adaptable and exciting alternative which is far from boring.

Jan 1, 1987

By Vanderberg B

A 3D, PC based computer program is currently under development by Blasting Analysis International, Inc., to analyze the kinetics of full scale blasts with two or more high-speed motion picture cameras. Todays common approach of utilizing only a single camera system can, in some cases, lead to great errors and erroneous conclusions when motion is assumed to be in a predefined plane of motion. CMe phrase, "What you see is what you get, it no longer true in 3D."). This is especially true in blasting environments which exhibit complex and/or predominant structural geology. The 3D system eliminates this problem, and includes automatic corrections for vertical and horizontal camera optic axis orientation, dimensional controls, lens distortion, field set-ups, projection imaging and digitized inputs. The only information required is the surveyed or known coordinates of at least six non coplanar points in the field of view. Motitn from each camera view is then digitized, transformed through a direct linear transformation, and processed with the 3D software, which also automatically time matches the data, even when the high-speed cameras are operated at different speeds. Eleven calibration constants are generated using an overdetermined system of linear equations to output the true 3D coordinates of motion in the time domain. Applications for this 3D approach are not restricted to just analyzing the kinetics of a blast. The system is sufficiently flexible to allow an accurate, quick and economical method of bench face profile analysis, generate muck pile profiles and estimate volumetric calculations. The recording systems for these applications can be common 35mm still photography and/or video equipment. It is envisioned that this system will soon replace expensive laser surveying systems at a fraction of the cost in the near future. It is also an excellent system to accurately quantify drill pattern layouts and the spatial locations of each blasthole. This information is required for generating single hole based synthetic seismograms to accurately predict the vibrational outputs of full scale blasts. In terms of litigation concerning claims resulting from blast induced ground vibrations to structures, the system is proving to be an excellent and economical method of performing pre-blast surveys where differential settlement is suspect.

Jan 1, 1990

This presentation opens with a definition of technology and how it is implemented. The expenditure and progress on R&D in the mining industry is then investigated and found to be difficult to quantify. The needs and interests of that industry including contribution to this Congress are examined and it is concluded that short-term rather than long-term goals seem to be prevalent. The presentation concludes with the opinion that the answer to the question in the title is both affirmative and negative but overall there is a need for the mining industry to become more innovative.

Jan 1, 1990

By Goode RA

It is-assumed that a pipeline system is economically justified as a means of transportation.. The terms "True Life" and "Economic Design Life" are defined. The most usual design alternatives to be considered from both physical and economic -viewpoints are listed and a summary is given of the main factors to be costed in assessing the relative economics of each alternative. A brief statement of the recor mended method af economic. assessment is given and an example is included. The paper aims to present a reasonably accurate, simple and practical method of considering the main economic factors which govern design.

Jan 1, 1962

By Masszi D

INTRODUCTION The association of methane with coal has been known almost since coal was first mined and in general it has been considered the curse of underground coal mining. Historically, most of the effort to handle this methane has been directed at diluting it to a safe level and preventing an explosive mixture of methane and oxygen from forming in any part of the mine. This is generally achieved by in-mine activites. This approach has two principal drawbacks, the severity of which are dependent on local conditions. The first is that the activity associated with the handling of the methane is undertaken in the mine and there- fore competes with the mining activity for the limited space available. The second drawback is that the whole methane handling activity is generally a cost to the coal because methane is so diluted that it cannot be used. With the value of energy increasing thi; second drawback is gaining importance so th.u several mines in Europe and North America ;it,, now installing systems to recover the methane in a useful form. Two approaches are

Jan 1, 1982

By Zenari L, Kent D

As our mines introduce more sophisticated production technology into their operations, the dependence on communication systems is markedly increased to allow the management of the technology. However the attention given to the communication systems has lagged that given the production equipment - namely LHDs, trucks and jumbos. At times it was treated as after thought. However, this is changing as the degree of automation increases in our mines. The communication system is now being given much more priority and is genuinely becoming a part of the mine design. The transfer of information around underground, as well as between the surface and underground, is an essential day-to-day activity, with the aim being a smoothly run operation. However the mine environment is far from static, and situations arise - such as breakdowns or other incidents - that require swift analysis of the issue, its cause and its remedy. Also, as communication systems become more sophisticated their use in areas, other than direct data flow, become available. The importance of communication, its development, and new areas being impacted by communication is the subject of this Paper.

Jan 1, 1997

By M Dorricott

This paper describes the design, construction and performance of sill pillars using cemented development mullock at the Crusader Gold Mine. The orebody is some 35 m - 60 m in length, 5 m - 8 m wide, dipping at 60¦ - 85¦ and plunging at about 40¦ to the north. It is accessed via a footwall decline. The ore occurs at the contact between basalt and ultramafic. This contact is characterised by shearing and alteration; and is prone to unraveling failure. The cut and fill mining method at Crusader extracts 25 m high ore blocks in four flat back lifts and one 8 m thick crown pillar. To enable full recovery of these high-grade crown pillars with minimal dilution, a 5 m thick sill pillar is constructed using cemented rock fill (CRF), after mining of the bottom two lifts in each block. Uncemented development mullock is used as rock fill (RF) for subsequent lifts. Development mullock and cement/water slurry is mixed underground to produce CRF. The fill is transported to the stope in LHDs and dumped on the floor. The sill pillar is advanced progressively, with compaction provided by the loader driving over the previously placed fill. Old jumbo rods are installed as shear pins along the flat dipping hangingwall to reduce the risk of rotational failure of the pillar. A fan of cable bolts is installed into the hangingwall to prevent unraveling failure in the sheared ground. Buffer blasting is used to minimise damage to the CRF sill pillar when the crown pillar below is extracted. At the time of writing, extraction of the crown pillar underneath the CRF has taken place at the 930 stope. The crown pillar was extracted successfully with dilution from the backfill and hangingwall minimised and 98 per cent of the gold recovered. This compares with pillars that were mined beneath uncemented backfill where only 70 per cent of the gold was recovered and where there was significant dilution from the backfill and from hangingwall failures. Where no CRF was placed, there were also numerous production delays caused by large rocks from the hangingwall blocking the stope brow.

Jan 1, 2002

German coal mining suffers from rock temperatures up to 600C which are the same as in South Africa at 3000 - 4000 m of depth. Therefore cooling plants have increased in the last decade and today a cooling power of nearly 200 MW is installed in the total Ruhr District. Cooling a mine is a little bit different from cooling a bottle of beer in a refrigerator in the kitchen because the heat taken from the bottle of beer is delivered to the kitchen some centimetres away; in mining the cooling-problem is more difficult: here the bottle of beer corresponds to the airflow at the coal face and the kitchen to the surface, So it is necessary to transport the heat or the "coldness" a long distance. In the address by Ieuan Morris some systems for transporting heat from the coalface to the evaporator of the cooling machine and further from the condenser of the machine to a return airflow were described. The following is a short idea of the way this problem is treated in Germany.

Jan 1, 1983

By J Araya, O Leiva

The mine evaluation process, composed of the designing, planning and valuation of a mine project, is, among other variables, based on an estimated orebody model. However, as the information from the drill holes is limited, it is impossible to know with certainty the mineral content in each block within the estimated block model. Consequently, uncertainty about the value of metal grades, or other geological attributes, arises because of the lack of information at unsampled locations. This is one of the reasons why, in any mine operation, there will always exist a divergence between estimated and real values. Cut-off grade optimisation is the process used to determine the operating mining strategy (long-term production scheduling) that will maximise the total profit value (normally referred as the net present value (NPV)) of a mine operation. This is done by defining a dynamic cut-off grade policy which is constrained by the production capacity of the mining, mill and refining.Real options is a type of contract, written on real assets such as mining, oil and other natural resource industries, that gives you the right but not the obligation to exercise the contract. It is based on operational and managerial flexibility, which allow mine decision makers to react to either good or bad operational and economic events in the future. But, what do geostatistics and cut-off grade optimisation have to do with the application of real options in a mine project evaluation process? The objective of this paper is to answer the previous question by showing how geostatistics combined with cut-off grade optimisation are key tools for corporate/managerial decision makers, which allow them not only to analyse the resource/reserves of their projects, but also to generate operational strategies that can maximise project value by minimising the downside risk due to ore tonnes and grade uncertainties, while achieving operational and physical constraints such as mining and processing capacities. A real copper grade open pit mine project is used as a case study.

Sep 26, 2011

A method is presented for calculating the number of cycles of stress to failure of a drill rod from operating variables; a mathematical analysis by Cooper of the stresses present in drill steels is applied to the forged collar, i1i-in. hexagonal hollow drill steel in common use in Australia; and an estimation is made of the dry fatigue limits at various points along a drill rod.It is shown that these calculations predict failure at a 'point where failure rarely occurs, and do not predict that failure should occur where it does in practice. The reasons for this anomaly lie in the neglect of bending stresses in the stress calculations, and in failuredue to corrosion fatigue at a preferred section rather than to simpler fatigue under non-corrosive conditions.INTRODUCTIONIt has long been recognized that failure of metal sections by fatigue is influenced both by the number of cycles of stress imparted to the section (N) and by the magnitude of this cyclic stress (8). In this paper, both Nand Shave been calculated for rods which have failed in service, and whose operating history is known. While the calculation of the number of cycles to failure is·simple, the calculation of stress is more complex. The results of stress caIculations predict that failure should occur only hi short rods, and then preferentially at the tip end rather than the shank end.However, in actual fatigue failures of steel rock drill rods, approximately 75 per cent. of such failures are close to the shank end, and failures near the tip end are rare.The usual explanation given for this high incidence of shank-end failures is that at the point of failure there exists, in forged collar steels of the type common in Australia "hardness valley" or. "m'etallurgical notch". This narrow valley in hardness is a weakness, and failure is expected to occur at the weakest point at the bottom of...

Jan 1, 1955

The authors have succeeded in providing additional rigour and clarity to the formulation and execution of the dynamic programming algorithm for optimum open pit limit determination. The inclusion of the blocks on the J + 1 column in the search for Pmax, and constraining this search with blocks assigned a value of negative infinity, ensures an optimal solution within the defmed blocks. The effect of the negative infmity blocks is to preclude mining along the diagonal blocks from the first row that they occur in. Figure 1 graphically illustrates the effects of this on the calculation of P. A practical application for constraining mining with negative infmity blocks is the case where the pit outline is defined by lease boundaries and not by the value of blocks to be removed. Any legal, social or physical constraint could be accounted for in the same way.The danger in applying this technique is that the negative infinity blocks will override any other more profitable solutions that may exist. This is in fact what has happened in the example that the authors use. If a further column is added to the left hand side (column -1) and the calculation is carried out again, a more optimal x-section can be found. (If the negative infinity values are removed the same result is obtained.) This gives a pit value of 112 as against the 108 of the authors' optimal pit. This calculation is shown in Figure 2. Lerchs-Grossman optimization is reliable only if there are sufficient columns available to allow "mining" to optimum depth of the ore body and still allow the pit to break out at the surface within the confines of the columns.This author's approach is to create enough columns each side of the lateral limits of the ore to allow the pit to intersect the surface while still within the confines of the block model. Implementing the methods discussed by the authors helps to reduce the number of columns required to achieve this.

Jan 1, 1987

By B Cope, N Hastings, D Webb

A Feasibility Study was completed in late 2002 to ascertain the risk and reward profile from the proposed deepening of operations at Perseverance Nickel Mine in Western Australia. The system and approach adopted to this brownfields extension work is outlined and the main components of the study are overviewed. In particular, emphasis is given to the integration of mine design and scheduling tools through to financial evaluation. Detailed comment is given on the ability of the system used to provide a robust project schedule complete with 3D animation. The level of importance in eliminating scheduling errors is demonstrated in relation to the reported bottom line viability of the project. It is suggested that this is an area where brownfields Feasibility Studies have lacked clarity and authenticity, leading to the creation of an unrealistic benchmark for project implementation.

Jan 1, 2003

By J E. Everett

A block model of the orebody is used to plan a mine. The first requirement is to identify ore to be extracted, discarding waste, so as to meet target grade, generally in multiple analytes. Commonly, cut-off values are set for each analyte, so as to distinguish ore from waste. It will be shown that, if more than one analyte is important, this procedure is wasteful of ore and a composite cut-off function is preferable.A second requirement is to sequence the ore extraction so that the variability in ore grade is controlled: failure to do so will result either in low-quality ore being marketed, or excessive re-handling being required to blend the ore to reduce the grade variability.A third requirement is that the extraction sequence should be such as to control the amount of equipment movement required, enhancing the equipment productivity.The overall objective, to optimise the Net Present Value (NPV) of the mined ore, is simply stated but complex in realisation, since so many factors, such as target grade, grade variability, equipment choice, equipment movement, and downstream blending all have alternatives which can be traded off against each other, and all of which contribute to the costs and benefits making up the total NPV.There exist commercial packages for ore selection and mine planning. However, they are often of a ‘black box’ nature, and users are sometimes not fully aware of the criteria being applied. In particular, the treatment of quality as a multidimensional vector may be problematic. The purpose of this paper is to discuss some of the issues involved and to suggest an alternative set of approaches, which should complement existing commercial treatments.The discussion will be illustrated specifically by reference to the mining of iron ore, but the issues are relevant to a wide variety of mining situations

Sep 5, 2011

IN carrying out experiments to determine the amount of metal taken away by fume or fine dust the apparatus used requires to be strong and compact, as it is generaIIy necessary to work on a staging fixed at considerable distance above the ground and against a smoke stack or flue. It is essential that the test be carried out at a part of the stack welI away from any bends, to prevent eddies. The method described below has been used for estimating the dust losses from Dwight & Lloyd sintering machines, antimony drossing furnaces, pot sintering trials, etc., and has been founc! satisfaetory. It is welI to bear in mind that the longer the period over which dust coIIection is extended, the more valuable the result is likely to be. The rateof aspiration of the gases through the apparatus is kept as regular as possible by changing the filter thimbles frequently, and the rate of flow should correspond closely with the rate of flow of the gases up the stack.The apparatus required for carrying out a test is as folIows :-{a) Thermometers : two are required, one for taking the temperature of the gas in the stack and one for giving the temperature of the gas in the aspirating drum. If the temperature in the stack is over 400° C., it is advisable to use a pyrometer such as the "Bristol" the couple being standardized before use at about the temperature of the stack.(b) Pilot Tube: The foIIowing sketch (Fig. 1) iIIustrates the principle of the pitot tube. The readings are to be taken in a straight flue, or stack, preferably 20 diam. away from any bend. A, which is open, faces the air current and...

Jan 1, 1922

By R S. Suglo, G-K Er

Mineral processing is an essential component of a mine production chain and it accounts for significant proportion of the production cost. Over the past decade, significant research progress has been made in processing plant efficiency using theoretical, experimental and simulation modelling techniques. However, these studies are limited to process plant system as stand-alone units with no interactions with the mining units. In order to maximise the total mining system efficiency and more accurately simulate the system, the processing plant must be modelled as part of an integrated mining system. This becomes increasingly important in continuous surface mining systems, with limited ore processing capacity. In addition, plant efficiency is roughly estimated with known parameters or with simplistic statistical data, without regards to the stochastic processes governing these parameters, such as processing plant feed introduction. In this paper, a comprehensive model of the ore processing plant system is given and the object-oriented design (OOD) of the system is briefly introduced. The joint operation of ore processing plant system and haulage system is analysed. Numerical modelling is used to analyse the ore processing plant system under different conditions. Analysis of the results show that the optimum plant capacity is 0.7 tons/sec (2520 tons/hour). The results also show that the plant system resources cannot be fully utilised because the production rate is always less than the plant capacity. When plant capacity reaches an optimum value 0.7 tons/sec, the production rate is about 0.64 tons/sec. The underlying stochastic processes associated with plant and mine capacities cause this variability. In order to reduce this variability, there is the need to tightly set tolerances for the function variables.

Jan 1, 2003