Search Documents

By Wang S

Fragmentation is the basic concern in rock blasting and serves as the main measure of blasting effectiveness. A good estimation of fragment size distribution before blasting is very useful and helpful for selecting the proper equipment for loading, transporting, and crushing rocks. A fragmentation model is presented that is based on a hole by hole analysis and correlates the rock properties, burden, spacing, and explosive column with the blasted volume and fragmentation obtained. The drill bench is divided into three separate areas corresponding to different breakage mechanisms. They are: 1) a main breakage or casting area, 2) a secondary breaking area, and 3) an overbreak area. The boundary of the main breakage area is found from the magnitudes of strains in the stress waves and the tensile strength of the rock. The secondary breaking area is determined by stress wave reflections at discontinuities and interactions between colliding stress waves from adjacent boreholes. The overbreak area is that beyond the main breakage area "where the reflected tensile waves no longer break the rock. This analysis is applied on a hole by hole basis to locate the breaking points. Then connecting the breaking points on each side of a borehole forms the triangle of the main breakage area. This is repeated for the next hole and the remaining area is the secondary breakage area. After the angle and area for each hole are found the Kuz-Ram model is used to predict the fragmentation size distribution for each hole. Then summing up the size distribution for each hole gives the total fragmentation distribution. This analysis has been successfully applied to field tests performed in a limestone bench where the entire spoil pile was screened to determine the fragment size distribution. Knowing the explosive and rock properties the breaking area was found for each hole, the strain and stress values, the breaking point, and angle of breakage (104 degrees). The fragmentation size distribution was then calculated and compared to the field data with excellent agreement.

Jan 1, 1990

A method is proposed for the determination of antimony in ores. Antimony is volatilized as antimony iodide by heating with ammonium iodide at a controlled temperature.The fusion mixture is extracted with hydrochloric acid and the antimony content is measured by atomic absorption spectrophotometry using an air/ acetylene flame. The time taken for analysis when comparedwith existing fusion and separation procedures is considerably reduced. Cations and anions likely to be present in antimony ores were also studied for possible interference effects but were not found to interfere.

Jan 1, 1972

The phrase "Total-Energy" has, during the past few years, become widely used to describe a wide range of very different operations. However, if accurately described they all have one basic factor in common - energy usage is optimised with the prime mover being powered by gas or oil to generate shaft horsepower and the products of combustion being put to some use. The item which distinguishes a Total Energy system from any other engine or turbine driven project is that orate pains are taken to utilize the waste heat, whether this be in the form of exhaust gases and/or engine jacket ling water. n areas where grid supplies of electricity are readily available, the economics of most projects undoubtedly hinge upon the successful application of waste heat. However, there has been a growing awareness of other benefits, such as reliability of supply, which can be incorporated into the system. In particular these factors sway managements of hospitals and companies with complex computer facilities to examine closely the feasibility of Total Energy, Consequently, in America for example, where many systems have proved themselves the list of applications is wide - shopping centres, apartment blocks, office buildings, airline terminals, universities, schools, motels. And these do not cover the industrial sectors where the range is wider. The total number in North America is now approximately 500 and this to some extent-speaks for itself. In Australia, the real work involved in carrying out feasibility studies for Total Energy is only just beginning. 'in some quarters, the concept is not well received in that it is too new. Therefore, a typical approach is to play safe and wait until some other company has proved its operation "under Australian conditions". This is certainly a realistic approach when considering something revolutionary but as far as Total Energy.is"concerned all the individual components and sometimes combinations, (engines, generators, boilers, air-conditioning units) have been in operation for many years. The only innovation is that they are now all being brought together under one roof. This should not be forgotten when the question "where can I see something like this operating?" is asked.

Jan 1, 1970

By Arbuthnot IM

It is the commonly held belief that, because the separation of liquids from solids takes place considerably faster in high rate thickeners than in conventional thickeners, high rate thickeners (HRT's) must use more flocculant than conventional thickeners. Data collected from a wide range of thickener users in Australasia and data presented in the literature is analysed. In addition, pilot plant data, with direct comparisons between HRT's and conventional thickeners, is presented. It is concluded that the flocculant consumption for both thickener types is in the same range.

Jan 1, 1991

Mining, like most other businesses, is based upon capital assets; and the primary cap- ital of any mining company is its ore reserve. A company's survival and growth is, thus, dep- endent upon its ability to replace, increase, redistribute and to diversify its ore reserves. A Kennecott executive addressing a group of geologists in 1957 stated, "Management expects a geologist to find ore! That is the primary objective and the justification of the geologist in the minerals industry. There is no other function that we can rationalize." This is, however, a restricted point of view, and one which I an sure is not fully shared by mining executives or mine operators at the present time. Ore reserves are 'made' as well as 'found' and the geologist contributes to this process. A mining geologist engages in activity in- volving the study of geology in connection with the total mining operation. His major task is the adaption of geological knowledge of ore de- posits and rock behaviour to mining needs, and the application of principles of the science of geology to specific problems of finding, develop- ing and extracting of ore bodies.

Jan 1, 1975

Mining, like most other businesses, is based upon capital assets; and the primary cap- ital of any mining company is its ore reserve. A company's survival and growth is, thus, dep- endent upon its ability to replace, increase, redistribute and to diversify its ore reserves. A Kennecott executive addressing a group of geologists in 1957 stated, "Management expects a geologist to find ore! That is the primary objective and the justification of the geologist in the minerals industry. There is no other function that we can rationalize." This is, however, a restricted point of view, and one which I an sure is not fully shared by mining executives or mine operators at the present time. Ore reserves are 'made' as well as 'found' and the geologist contributes to this process. A mining geologist engages in activity in- volving the study of geology in connection with the total mining operation. His major task is the adaption of geological knowledge of ore de- posits and rock behaviour to mining needs, and the application of principles of the science of geology to specific problems of finding, develop- ing and extracting of ore bodies.

Jan 1, 1975

While sampling techniques used by the mineral industry continue to improve, sampling is still an area which is often neglected. It is often left to personnel who do not fully appreciate the significance and importance of sampling. Yet sampling and sample processing are of vital importance. There is little point in making major capital investments in the latest analytical equipment and spending considerable time obtaining the best analytical precision, if the sample provided for analysis is seriously biased in the first place.

Jan 1, 1976

A model of dense medium cyclones is developed based on balancing the terminal velocities of the discrete particles due to the centrifugal force against a random turbulent eddy velocity. An expression of the form P - or Q _ 1 100 e."A where P is the partition number., is a function of cyclone efficiency, particle size and density differential between the particle and medium, and is the slurry spilt, is developed and may be used for regressing plant partition data. The above model provides an understanding of peculiarities of the partition curve such as asymmetrical tails, elevation of the cutpoint and elevation of the d50 with increasingly fine feed. The effect of feed variables such as particle size, medium viscosity and changes in spigot or vortex finder diameter is shown. A means of convoluting the partition curve with various feed washabilities is discussed together with how the above may be used to evaluate plant performance for a variety of feeds.

Jan 1, 1987

The development of computers is examined in the context of the mining industry. The risk element is given as a reason for the slow introduction of the computer into mining. Dealing with mining's uncertainty is seen as a major role for computers. The use of computers is traced from early accounting applications to current involvement with all aspects of mining. The problems associated with increasing use of computers and their impact on management is discussed in depth. Disenchantment of management is thought to arise from unfulfilled expectations. Contributory causes are given as overselling of computers, reaction against change, speed and growth of computer technology. The solution is seen to lie in a more dominant role for user management in the development of computer systems and greater emphasis on education. The computer of the future will then become integral to the mining process as an extension of management's planning and control function.

Jan 1, 1974

In planning and operating mining projects, managers must take into account economic conditions in foreign markets in addition to Australian conditions. As the manager has little influence over the price or the demand for the product, it is particularly important that close attention is paid to the control of costs to ensure that the mining operation remains competitive with foreign producers. This is not necessarily true for some sectors of the domestic manufacturing industry where foreign competition is restricted and costs can be passed on to consumers because of the protection afforded by tariffs. The effects of protection on the cost structure of Australian industry are more pervasive than is commonly understood. The issue of protection is particularly important to the Australian mining industry management because the cost burdens imposed by local protection must be absorbed within profit margins. Furthermore, because protected industries are effectively subsidised to use scarce resources such as skilled labour, the development of more efficient industries such as mining is inhibited. The mining industry has much to gain from any relaxation in protection policy, and hence the issue is of considerable importance to all managers in the mining industry concerned with costs.

Jan 1, 1980

There are a number a stages in a project at which an audit must, or should, be undertaken. An independent audit may be necessary for the comfort of directors and/or financiers before the major finance is committed, but an internal pre-development audit is the opportunity for the management team to take stock of the project and reaffirm their confidence and commitment. Maxims for project success are given and a check list for pre-development audits is presented. The need of mid-development audits may arise and their brief will depend on the circumstances arising. A game theory approach to decision-making is demonstrated in which the alternative of fast-tracking a development is considered. At the conclusion of the project, before the team is disbanded, a post-development audit should be made. Valuable learning can come from this process which could give important guidelines for future projects and a check list is presented.

Jan 1, 1997

By Yamamoto Y, Ohyama H

In case of NATM, mechanical cutting is desirable in view of the original purpose of not spoiling natural ground. As typical tunnelling machines, there are two (2) kinds available: one is "Full Face Excavator" known as TBM (tunnel boring machine), and the other is "Roadheader" known as Part Face Excavator. By the use of the former, accurate profile cut is made possible, but there is a limit in the shape of a cutting section. By the use of the latter, cutting of various sections is made possible, but in order to cut a section economically and accurately, operators are required to have a high level of skill. In this text, we introduce Automatic Controlled Profile Cutting System (hereafter "ACPC" System) developed as a roadheader.

Jan 1, 1987

Grade control plays an essential role in the good running of a mine. The factors at play are many, starting from a good analysis of the geology and a correct sampling procedure. Once this is achieved (and it is an essential prerequisite), the problem is to adequately define what is ore and what is waste. This paper tries to show, through a small example, how simple geostatistical techniques (variography, and moving average or kriging), can help in accurately defining these limits in a geologically homogeneous zone, thus allowing optimal use of the available information.

Jan 1, 1987

By Hammett PHJ

Oil Exploration Companies are primarily interested in how much oil or gas is present in the rocks in an area in which an exploratory well is drilled. The solution of this problem requires a combined effort on the part of the petroleum geologists, drilling engineers, logging and drilling contractors. To help in'explaining how the drilling and evaluation is earried out the paper has been divided into two sertions, one titled Drilling which is presented by Mr. P.H.J.-Hammett and the seeond titled Evaluation which is presented by Mr. R.M.L. Elliott. A typical Perth Basin Well has been chosen as art example for this presentation. In Figure 1A is shown the type of sandstone and shale sequence encountered in this area.

Jan 1, 1964

It is suggested that if adequate knowledge is available about classifiers in closed grinding circuits, these units may be used as on-stream size analysers when equipped with suitable sensing devices. Research work which is at present in progress to enable a hydrocyclone to be used for this purpose is discussed.

Jan 1, 1967

By Meloy TP

Several important, fundamental aspects of the grinding behaviour of mineral systems are addressed. The Levenberg-Marquardt algorithm for systems of constrained non-linear equations was used to solve the steady-state and dynamic population balance model (PBM) grinding equations to obtain the mill matrices and grinding selection and breakage rate functions, respectively. The fact that the PBM model equation Inverse Problem is degenerate or underspecified is demonstrated. Multiple solutions to the same PBM equations are provided. It is shown that there is no unique solution to the Inverse Problem unless additional constraints are provided or assumptions are made such as the Arbiter-Bhrany normalisation assumption. The severity of the non-uniqueness problem for steady state grinding is demonstrated in several examples using typical feed distributions and mill matrices. In addition, it is also demonstrated that when higher than single powers are used in steady-state mill matrix expressions during simulation or calculation (or iterative procedures are used during numerical simulation) and four or more size intervals are used considerable amount of error is propagated throughout any calculation. Each solution to a PBM, while giving the same prediction during a single mill pass, gives different solutions or predictions for mill composition upon subsequent passes. In addition, it is shown that there is a problem with building up a grinding mill knowledge base with PBMs. A similar analysis was done for the dynamic or kinetic PBM equations. The fact that the dynamic PBM Problem is degenerate or underspecified is also demonstrated. Multiple solutions to the same dynamic PBM equations are provided. Again, it is shown that there is no unique solution to the Inverse Problem unless additional constraints are provided or assumptions are made such as the normalisation assumption. Each solution to a dynamic PBM, while giving the same prediction for a given grinding time interval, gives different solutions or predictions for mill composition for other grinding times. Actual experimental grinding data was assessed to determine the functionality of mill selection and breakage functions. The functionalities obtained through constraints were compared with those obtained with the normalisation assumption of Arbiter-Bhrany which relates breakage functions to particle size distribution. The capability of the population balance model to predict grinding behavior over time in various mineral grinding systems was assessed. The required functionality of selection and breakage functions for effective prediction of grinding behavior in mineral systems is discussed.

Jan 1, 1993

The phrase "Total-Energy" has, during the past few years, become widely used to describe a wide range of very different operations. However, if accurately described they all have one basic factor in common - energy usage is optimised with the prime mover being powered by gas or oil to generate shaft horsepower and the products of combustion being put to some use. The item which distinguishes a Total Energy system from any other engine or turbine driven project is that orate pains are taken to utilize the waste heat, whether this be in the form of exhaust gases and/or engine jacket ling water. n areas where grid supplies of electricity are readily available, the economics of most projects undoubtedly hinge upon the successful application of waste heat. However, there has been a growing awareness of other benefits, such as reliability of supply, which can be incorporated into the system. In particular these factors sway managements of hospitals and companies with complex computer facilities to examine closely the feasibility of Total Energy, Consequently, in America for example, where many systems have proved themselves the list of applications is wide - shopping centres, apartment blocks, office buildings, airline terminals, universities, schools, motels. And these do not cover the industrial sectors where the range is wider. The total number in North America is now approximately 500 and this to some extent-speaks for itself. In Australia, the real work involved in carrying out feasibility studies for Total Energy is only just beginning. 'in some quarters, the concept is not well received in that it is too new. Therefore, a typical approach is to play safe and wait until some other company has proved its operation "under Australian conditions". This is certainly a realistic approach when considering something revolutionary but as far as Total Energy.is"concerned all the individual components and sometimes combinations, (engines, generators, boilers, air-conditioning units) have been in operation for many years. The only innovation is that they are now all being brought together under one roof. This should not be forgotten when the question "where can I see something like this operating?" is asked.

Jan 1, 1970

McLeod: Without getting into the argument as to how well we can know our resource levels specifically in the immediate short term, I would like to make one or two points about the future, and perhaps try and persuade people that they are not really facing a doomsday. It is fair to say that over the last few years the rate at which we have increased our resources has far exceeded the rate at which we have used them, and this is likely to continue for quite a few years yet. As people are now looking for a substitute for petroleum, later on we will be looking for a substitute for coal, should the position get serious. After all man is pretty versatile, has plenty of initiative-and makes allowances for experience. It has been demonstrated here by the way people are looking at use of low quality coals and better use of the coals that are available. It would be fair to say that what now we regard as economically submarginal deposits will, by the time we need them, become economic. I think that there is quite a lot in front of us in exploration and finding new reserves. I would like to have comment from yourself sir, because I recall reading a report of a meeting, here in Wollongong I think it was, in which you addressed the local branch on the future of coal in Australia, and you said that the coal basins of Australia had been well explored and there was not much chance of new discoveries. Since that time we have seen some thousands of millions of tonnes turned up in the Galilee Basin of Queensland, we have seen five hundred million tonnes turned up in Lake Phillipson in South Australia. Do your previous comments still apply? I would like to hear from some of the exploration people, who are operating on an Australia-wide basis, as to how they regard our chances of discovering significant new deposits and significant extensions of known deposits. H,artnell: Mr. McLeod has asked me to comment on what he has just said. I think that the important thing is that our knowledge of the main coal basins in Eastern Australia is increasing in detail but for the most part the extent of coal basins is not being increased in respect of their superficial areas. There are additions but they are not substantially changing our expectation of what the main coal basins will be. I believe that our task is essentially to intensify our knowledge of the main coal basins that we know about. This is important for example for the various reasons that Mr. Roach was talking about, that is the problem of surface alienation, jeopardising the chance of recovery when you go to underground operations. My approach to this whole problem is predicated on the belief that coal has a special destiny to perform in the next fifty years. I believe that it is going to take up to fifty years and maybe a little longer before the enormously demanding technology for nuclear power recovery is in fact achieved. When it is achieved the supply of energy to the world will be enormous, much beyond what we have ever even dreamed about. The mind boggles at what the people of the middle of next century, of two thousand and fifty, will command in the way of physical resources. It is going to be, I believe, tremendous, but the technology involved is very demanding. I mentioned to Mr. McLeod the other day that according to the information that I got in November last, 60% of the nuclear power stations in the United States were out of action, by automatic cut offs because of safety requirements. The technology of breeder reactors seems each year to be a bit further off. In the meantime coal I am sure is going to be called on to supply power directly to fluidised bed and other technologies for power generation. It is going to be called upon in the near future, I believe, to supply liquid fuel on a vast scale and the only thing in my view that we should be thinking about is whether the coal producing countries of the world will succeed in producing as much coal as is going to be demanded. I believe the real challenge to the coal mining industries of the world is that they may fail to do what is going to be demanded of them. This is a challenge I believe to mining technology. I think that we should be working deliberately and energetically finding ways and means where underground recoveries, instead of averaging 50%, can average 50% plus, plus, plus, and this is the first requirement. We should be spending many millions every year, here and overseas, on increasing our means of winning coal because every tonne of coal that is alienated and left irrecoverable in the earth is going to weaken the capacity of the coal mining industry to fulfil, what I believe to be its destiny in the next 50 years.

Jan 1, 1975

The following is a brief summary of the Bulli Colliery and its method of operation when Australian Iron and Steel Ltd. took control.Bulli Colliery is situated about a mile west of the village of Bulli and is some 10 mUes north of the Australian Iron and Steel Company's Steelworks at Port Kembla.The mine is owned by Australian Iron and Steel Limited, who purchased it in 1936 from the liquidators of Bulli Colliery and Coke Works.It is one of the oldest working coal mines in Australia, having been opened about 1858 and has worked more or less continuously since that date.The seam worked is the No. 1, or Bulli, Seam, which outcrops along the escarpment of the Illawarra Range and is generally operated by tunnels, the portal at Bulli being some 440ft. above sea level.The colliery holding is fairly extensive, but the coal seam over a large portion of the area within two miles of the outcrop has been more or less destroyed by an intrusion of basalt.At present there is no coal being worked within a distance of about 21 miles from the surface, the farthest workings being about four miles from the tunnel mouth.The existing main haulage road, for the first two miles from the portal, is not straight; it is very narrow over fairly long stretches and has many changes of grade varying from 3% in favour of the load to 13% against the load.The dumping station and screens are situated close to the portal of the haulage tunnel, and at this point the coal is loaded into railway hopper waggons, which are then hauled by rope to the top of a self-acting incline. The waggons are lowered down the incline, a distance of approximately! mile, the ruling grade being about 18 %.From the bottom of the incline, waggons are hauled by Company's steam locomotive to exchange sidings from whence they are taken by New South Wales Government Railway engine to the Company's Steelworks at Port Kembla.

Jan 1, 1947

COAL constitutes such a gigantic item in modern industry, either for direct heating, production of coke for smelting, or for the generation of power, that its quality and price play a very significant part in economic industrial progress. Australia is still a very young country industrially, and is groaning under many disabilities compared with competitors overseas, not the least of which is the quality of coal. Linked with the word "quality" should be that of "utility," for high-ash content prevents efficient utilization of the fuel.The marketing of good quality coal is a very important matter indeed, and if industry in Australia is to progress in the way that it should, this matter must receive keen attention.New South Wales, above all the other Australian States, has been blessed by nature with vast coal-fields, from which fuel is shipped to every State, and provides the base for power for most of our railroads and industries.Experts frequently refer to the fact that in some districts only partial extraction of thick seam coal is being made, without a care or thought for the future. Ranking next in importance to this is the fact that much of the coal is being carelessly marketed.Very few collieries in Australia are equipped with coal-washing plants for dealing more particularly with small coal grading which most industries require, and to which coal producers as a whole pay the least attention. In England each year nearly20,000,000 tons of coal is being water-washed before sale, and is marketed as a fuel of far greater utility once it has been freed from extraneous ash.Investigation proves that a great many pits in New South Wales are marketing coal (more particularly small coal) containing a considerable quantity of extraneous ash, due to the admixture...

Jan 1, 1926