Search Documents

By Rashad MZ

The evaluation of ore deposits consumes much effort, cost and time, hence research work must aim to minimize these inputs with no loss of accuracy. The present study is devoted to assess the optimum conditions and methods of calculations which give minimum costs of ore exploration. An area of (a x a) where "a" is the zone of influence of the semi-variogram, i.e. (2800 x 2800 square metres) located within the Abu Tartur plateau is the subject of the intensive study. The distances between boreholes are varied ie. a/4, a/6, a/8 and a/ 10 respectively. The average ore grade (G), thickness (t) and relative ore reserves (tG) are calculated by four methods. The results indicate that at a distance equal to a/5, the inverse distance squared method gives the best results. These parameters save about 50 percent of the cost of exploration with a map accuracy greater than 90 Percent.

Jan 1, 1987

By G T. Hefter, P Singh

Sulphur dioxide oxidation is an attractive alternative anodic reaction to the evolution of oxygen in copper electrowinning. Accordingly, the electrochemical oxidation of SO2 in aqueous 1.0 x 10-1 mol/L NaClO4 has been studied at pH 2.3 using platinum and glassy carbon electrodes. On the platinum electrode SO2 oxidation occurred on the forward scan at 0.96 V and on the reverse scan at 0.63 V. For GC, a single SO2 oxidation peak occurred at 1.40 V on the forward scan. SO2 oxidation on both electrode substrates was hampered by oxide layer formation. The electrode could be reactivated however, by oxide layer reduction. Although reactivation was most successful for platinum, SO2 oxidation on platinum is quite complex, with this evidenced by the reverse scan anodic peak. Glassy carbon shows simpler behaviour and thus, is the preferred substrate for SO2 oxidation.

Jan 1, 1998

By J H. Wood, I Gray

This paper examines the occurrence of outbursts, coal bursts and rock bursts in underground mining. It then examines them from the viewpoint of the failure mechanism and velocity of particles. The presence of gas is extremely important as it can both act as the fluid pressure component of effective stress leading to failure, and as a substantial energy source in projecting material during a burst. For gas to drive a dynamic event it must be present as free gas held in voids within the rock or coal mass. This can pre-exist the burst event or be released from desorbing gas during it. The latter is typically part of a multi-stage outburst event which can reach very large proportions. Rock and coal bursts are driven by strain energy release and can vary in form. These tend to be single events associated with failure and strain energy release. It is also possible to conceptually have hybrid events where the failure of the mass and the energy release are due to both stress and expanding gas.

Nov 29, 2022

By Bisshop J. P W

Maximum recovery of sulphide minerals by flotation is achieved over a limited size range. Valuable particles above and below this range have a smaller probability of being recovered. In the normal grinding-flotation operation, not all valuables are reduced to the optimum size range, and therefore sub- stantial losses occur. A significant improve- ment in the size distribution is not usually possible within the conventional circuit, and a more complex arrangement may be necessary to obtain optimum recovery of the valuable mineral. This problem is considered with refer- ence to the Mt. LyeZl concentrator. The performance of the existing circuit is dis- cussed, and it is shown that losses in recovery occur in both coarse and fine sizes. Laboratory tests indicate that regrinding the coarse particles results in an increase in recovery of up to 4%. Redistribution of plant grinding capacity to reduce initial grinding power by 6% and use this capacity to regrind coarse particles was considered. It is con- cluded that overall plant efficiency would be increased by 2% provided that overloading of the regrind mill could be avoided.

Jan 1, 1977

By Gardavsky V, Gabell AR, Green AA

The I,)hyllosilicate mineral chlorite is a common constituent of altered rocks associated with volcanogenic massive sulphide deposits, and literature studies indicate that, in general, this mineral is progressively enriched in magnesium relative to iron as an orebody is approached. Studies have shown that there is a direct correlation between the Mg/Mg + Fe ratio of chlorite and its absorption spectra in the 2.7 to 3.0 um range. However, this region, which contains the fundamental 0-H stretch absorption features, is affected by intense atmospheric absorption, and therefore cannot be used for remote sensing. At shorter wavelengths (0.4 - 2.5um), there are windows where the atmosphere is sufficiently transparent and vibrational absorption bands still occur, although they are clue to overtones and combinations, and accord- ingly are much weaker than the fundamental features. Shifts to longer wavelengths with increasing iron content can still be observed in this region of the spectrum and, with better spectral resolution and sensitivity, it may be possible to monitor subtle variations in chlorite chemist by remote sensing techniques.

Jan 1, 1987

By A Gibbs

The mining sector has been a leader in investing in safety improvement initiatives, yet relatively few mining organisations can accurately track the positive effects of these initiatives or identify areas that may require more attention. The consequences of not taking safety seriously are severe, and unfortunately injuries and fatalities are continuing to occur across the mining sector (Brady, 2019). There is a tendency to turn to lag indicators such as All Injury Frequency Rate (AIFR), Total Recordable Injury Frequency Rate (TRIFR), and Lost Time Injury Frequency Rate (LTIFR) to track these outcomes. As outlined below these approaches are inherently flawed and a renewed focus is needed on indicators within the control of leaders, indicators that have high predictive validity for future events and data that is used in a way to enable learning and change.

May 5, 2022

By K Sherry, N Shahbazi

Scope 3 emissions are a set of often overlooked indirect greenhouse gas emissions within a company’s value chain and represent the majority of emissions for many sectors. These emissions arise from activities conducted by entities beyond the reporting organisation’s ownership or direct control and are often challenging to calculate. Scope 3 emissions typically encompass purchasing goods and services, transportation and distribution, managing operational waste, downstream processing and utilising sold products. Within the mining sector, scope 3 emissions often constitute a significant portion of the overall carbon footprint. Therefore, these emissions are a significant aspect of the future of sustainable mining. As the journey towards a world committed to achieving Net Zero Emissions has started, the time to spark a transformative conversation in the mining industry has arrived. Consequently, a better knowledge of scope 3 footprints allows organisations to assess their emission mitigation projects against the total carbon impact of their operations and products.

Sep 1, 2024

By M Grinceri

The New MetroRail City Project was completed in 2007 in Perth, Western Australia. The project included construction of two underground stations, twin bored rail tunnels of 1.4 km combined length and cut-and- cover tunnels and dive structures of about 1 km total length. It is the first major underground construction project within the Perth central business district (CBD). This paper provides an introduction to the project and describes the geology and hydrogeology of the area. Ground conditions varied significantly along the alignment from soft estuarine muds in an area of reclamation to very dense cemented sands and very stiff to hard clays. Deep foundations for the project extend down into the bedrock below the CBD, a Tertiary siltstone/sandstone. Key geotechnical hazards encountered during the project are discussed. The building protection methodology on the project is described, including damage assessment, condition surveys, monitoring and protection of key structures.

Jan 1, 2008

By Ueki S

Underground coal gasification (UCG) is a promising process for obtai- ning energy from coal, which is either unmineable with current mining techno- logy or uneconomic to recover, using conventional methods, in the present energy market situation. There are several coal fields, which could become new coal reserves, if the UCG process were successfully applied. In the 1960's Japanese researchers made a number of basic studies and field tests into UCG, although not all of them produced favourable results. This paper reviews Japanese research on UCG. This includs basic studies into coal gasification using a small, tube reactor fed by air and oxygen, and also large scale model stu- dies(reactor size of 8.Om x 2.4m x 1.5 m). Field test results from Akabira colliery in Hokkaido and a feasibility study of power generation using UCG from a coal field in Hokkaido are also Presented.

Jan 1, 1987

By Lynce AJ

A method has been developed for the prediction 'of 'the- . performance of a multi-stage grinding=cyclone classification circuit of any degree of complexity on any ore for a wide range `of operating conditions, The-.method involves ;the. s` inu ation b'f the circuit on a digital computer by means of. matheinatical' models ":bf the"' individual units:, the. development of which is- also discussed'., At present, in order to establish 'the!'" charac'teristtics of they ¦ore- and the machines. in mathematical terms;. it is necessary to know'the performance of a , simpl,.e. ; system on tri.e ore - for! one known ,,feed rate and.fe.ed s,l-zing, analysis. ' ,Fiiither work on :the- separate identification 'of the terms defining the characteristics of the ore and the machines may permit the method to be, applied directly to the cj.4ta,derived from small scale tests on ores,

Jan 1, 1964

Chlorine as a lixiviant for gold possesses a number of significant chemical and Idnetic advantages over cyanide but because of its corrosive and vaporous nature the method of implementation needs to be significantly modified. At comparable reagent concentrations the dissolution rate for gold in the C12/Cl- systems is some 10 - 100 times that achieved in the 02/CN system. The dissolution rate in the chlorine system is largely a function of the concentration of C12, Cl- and pH. Under conditions of low Cl', (less than 50 g/1), the dissolution rate begins to drop off dramatically over the pH range from 3 - 4. Increasing the level of dissolved chloride ions shifts the pH of this rate reduction to around pH 5 at 100 g/l NaCl, and to around pH 6 at 300 g/l NaCl.

Jan 1, 1991

The Lake Rotokaua sulphur deposit, near Taupo, New Zealand, is a lacustrine sedimentary ore body, 220 acres in area and from 7 ft to 96 ft thick, containing, within the area drilled to date, some 20 million long tons of ore averaging 25% elemental sulphur in unconsolidated tuffaceous diatomaceous clay, overlain by about 120 ft of pumice sand and by the shallow Lake Rotokaua. An additional amount of perhaps 4 million tons of sulphur is regarded as probable in the area remaining to be drilled. Current economic studies cover the problems of mining an unconsolidated water-saturated formation with some residual thermal activity nearby; conservation and restoration after mining in a scenic recreation area; beneficiation of the ore and extraction of high- purity sulphur, principally for fertilizer manufacture. The deposit has additional importance as a pointer to possible further discoveries in the Thermal Region.\

Jan 1, 1971

By Jones BH

Discovery of the Vera-Nancy deposit in late-1995 followed 12 years of active exploration in and around the Pajingo Epithermal System, an andesite hosted veinfield covering an area of 150 square kilometres at the northern end of the Devono-Carboniferous Drummond Basin in North Queensland. Early exploration targeted open-pittable resources in the numerous auriferous veins and it was not until 1994 that exploration focus shifted to drilling to depths below about 100 metres from surface, which resulted in the Vera-Nancy discovery. That deeper drilling process is still at a very early stage of coverage of the epithermal system as a whole and substantial potential exists for additional discoveries.Drill-out of Vera-Nancy has to-date established a gold resource in excess of 1.4 million ounces. Mine development is proceeding via a twin decline system with first stoped production scheduled for August 1997.

Jan 1, 1997

By Dunne R, Defilippi J

Dump leaching began at Teller in late-1988 at a rate of 4 MTPA and has been progressively expanded to the present rate of 10 MTPA. Teller's on-going commitment to dump leaching is driven by the amenability of gold ores to the process and the availability of large tonnages of low grade gold ore. The sequence of evaluating ores for dump leaching involves rolling bottle tests on coarsely ground ore, followed by small and large column leaching and finally trial heaps. Trial heap tests are very expensive and an alternative approach to this is large diameter column leaching.A four-column permanent facility was built at Teller to specifically evaluate the leaching characteristics of new dump leach ores. Details of construction, operation and dismantling are discussed in the paper. Capital cost for the four column facility was some $45 940, while operating costs are about $24 800 per column.

Jan 1, 1992

By K Biegaj, S C. Dominy

A high-nugget effect and presence of coarse gold characterises many styles of gold mineralisation. The effective sampling of these deposits is often difficult because of the relatively low concentrations involved and erratic nature of the gold or other minerals. Geometric and/or metallurgical complexities often compound this effect. Underground development, in-fill drilling and bulk sampling/trial mining are generally required to delineate Ore Reserves. Similarly expensive definition strategies often apply to surface mining in complex orebodies of gold and other minerals, including precious stones. Development, particularly winzing is a historical technique that was used to gather geological, grade and metallurgical data during underground and near-surface exploration. It permits access to the mineralised structure below the surface datum to determine viability. Winzing has always been considered an arduous and dangerous task. Modern winzing technology has led to the development of the Mobile Supersucker – essentially a giant vacuum cleaner with underground and surface capabilities. By the elimination of shovel-loaded blasted winze material into a kibble and hoisting, this system permits safe and highly efficient winzing activities, and allows the collection of bulk samples for grade and metallurgical evaluation, as well as access to the mineralisation for geological and geotechnical mapping. Bulk samples from horizontal development have long been collected to help define mineable grade via pilot processing. However, when defining blocks below current development, there has been over-reliance on ineffective ‘small sample’ drill data. The Mobile Supersucker permits the development of winzes and off-winze sub-levels. These provide critical information to a mine technical team when trying to justify capital to go deeper or commence or deepen an existing open pit. CITATION: Biegaj, K and Dominy, S C, 2018. Lowering risk in complex mineralisation: application of mobile supersucker development, in Proceedings Complex Orebodies Conference 2018, pp 113–115 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By K Sommerville

BHP Billiton’s Area C iron ore operation has been in production since 2003. During 2010, below water table mining in the Marra Mamba formation commenced and dewatered ore has been successfully processed through the plant.The ability to mine below water table material increases reserves. Pits can be dewatered using a combination of ex-pit and in-pit bores. Critically it is important to allow suffi cient lead time to dewater. For Area C, in-pit bores yield the most water which presents challenges in every day operations when mining around bores. Operationally there are steep learning curves in obtaining equipment, training personnel and setting up infrastructure. Core risks include lifting, refuelling and maintaining gensets. The pipework, extraction and re-establishment work can be very manual.The challenges include blasting, mining, stockpiling, processing, water balance and disposal. Maximising up time on bores whilst minimising impacts to blast practices have evolved. Blast practices now align bores to the edge of patterns. Protecting bores have evolved from stemming bores with rock and re-drilling to using gas bags which require no drills. Based on moisture and material properties, mining of dewatered material can be categorised into three groups:1. normal,2. sheeting, and3. sheeting and top loading.Ore can go straight to the plant ore to drying pads where it takes between one and three months to drain.Stock management of these piles is important to ensure efficiency of the plant. Rules have been established for blending wet material to maintain feed capacity and some modifications to plants have been made. Dewatering of pits poses a challenge for water use. Initially turkey’s nests were established to capture water and use for dust suppression. As water abstraction has increased methods of management include using exhausted pits for storage and evaporators. Managed Aquifer recharge and use in potable water are being considered. An over arching coordination of the capacity and use are required.Important elements in dewatering include:• capacity models,• capital,• long to short planning,• day to day coordination, and • water level monitoring and balances. Success in dewatering requires a cross function team working towards a common goal. *This is an abstract only. No paper was provided for this abstract.*

Jul 11, 2011

A flow sheet has been developed to treat a high tonnage highly preg-robbing gold ore. The ore is low grade and fine grained with a high proportion of very fi ne free gold. The key components of the flow sheet include gravity, flotation, intensive cyanidation with direct electrowinning, and carbon-in-leach of the flotation concentrate. The circuit produces a low overall mass pull to concentrate allowing economic intensive treatment of large tonnage low-grade material. Efficient recovery of fine gravity gold using a Falcon concentrator in both the milling and flotation circuits, and subsequent intensive cyanidation in a Gekko InLine Leach Reactor (ILR) is critical to the process with over 70 per cent gold recovery expected in this circuit. Grind size control was also found to be important in controlling the activity of the preg-robbers in the carbon in leach circuit and also in the solid liquid separation performance. Tests at the large-scale demonstration plant have been conducted to demonstrate the effectiveness of this flow sheet. A large low-grade deposit is currently under development with the aim of developing a 10 Mt/a treatment plant with the subsequent addition of equivalent sized process lines in multiples of 10 Mt/a. The economic development of this orebody is critically dependant on understanding and exploiting the properties of the ore. In particular it is critical to minimise the effect of preg-robbers by recovering free gold with Falcon concentrators and InLine Leach Reactors. Recovery of the remaining gold by flotation into a small mass yield allows this fraction of gold to be treated by CIL leaching utilising high carbon levels. It is critical is to ensure operation at the optimal grind size to maximise liberation of the free gold and minimise pregrobber activity. The ore has been identified as preg-robbing with low recoveries obtained if treated using conventional cyanidation and carbon absorption. The mineralogy consists of predominantly fi ne grained free gold with minor sulfides including pyrite and arsenopyrite. With conventional cyanide leaching in the absence of carbon, gold recovery is less than 50 per cent. Direct cyanide leaching of the ore in the presence of activated carbon results in an improved but still uneconomic gold recovery. The gravity recoverable gold (GRG - as defined by Andre La Plante) content of the ore has been measured to be 70 per cent to 85 per cent in various tests with liberation grind size of approximately 106 ¦m. This indicates gold is predominantly free and suitable for recovery by batch centrifugal concentrators into a low mass yield. This property of the ore presents the opportunity to maximise the recovery of gold by separating it from the majority of the preg-robbers prior to leaching. Due to the very fine gold particle sizes and the necessity to maximise recovery of this fine fraction Falcon concentrators were selected for the duty, with their proven high recoveries at very fine gold sizes. The gravity recovery in the milling circuit is designed to be in the range 55 to 65 per cent. This has been achieved in the existing pilot plant using a Falcon operating on ball mill discharge within the mill recirculating load. Intensive leaching in an InLine Leach Reactor is essential to recover the gold from the gravity concentrates. Tabling is not a preferred option since recovery is lower than intensive cyanidation and any gold losses to table tails will report to CIL where recovery is reduced by the presence of preg-robbers. Furthermore, tabling recovery from the gravity concentrates is particularly poor due to the fine particle size of the free gold. ILR recoveries of 98 per cent were demonstrated in the pilot plant using an ILR100BA and leach conditions were investigated in the lab using pilot plant generated Falcon concentrate. Recovery of gold from the pregnant solution was achieved with direct electrowinning at pilot and efficiency and sizing parameters were determined at lab scale. To further increase free gold recovery Falcon concentrators will be installed in the flotation circuit. Location of the Falcons in the circuit is not finalised but installation on the rougher concentrate stream is favoured since it will allow multiple pass recovery. This is expected to recovery a further ten to 20 per cent of the gold, as indicated by lab tests on pilot plant generated material. The gravity concentrate from the flotation circuit will also be leached using InLine Leach Reactors. Initial intensive cyanidation tests carried out on lab generated flotation concentrates indicated higher recoveries than CIL can be obtained even though the concentrates contain significant levels of preg-robbing material. This can be explained by the high cyanide, high pH leaching conditions used in the ILR which alters the absorption equilibrium of the preg-robbers. Further optimisation of the leach conditions will be undertaken once more concentrate becomes available. Recovery of the remaining gold content is achieved by flotation into a small mass yield, however the preg-robbers are also recovered into this concentrate. Due to the presence of the preg-robbers gold leaching must be carried out in the presence of high levels of activated carbon in a CIL system. The recovery has been shown to be strongly dependant on the carbon loading and the concentrate particle size. The carbon competes against the preg-robbers for dissolved gold while excessive grinding increases the surface area and activity of the preg-robbers. This has been demonstrated in test work however the economic optimum leaching conditions and carbon loading have yet to be determined. The grind size is critical to the economics of the project, not only due to its effect on gold recovery but also due to its effect on the major operating and capital costs at both the front and back end of the process. It is critical to grind enough to obtain both gravity free gold and flotation liberation at low mass yields however over-grinding results in large increases in mill size and power at the front end and filtration or thickening costs at the tails. Because these unit operations treat essentially all the plant feed even small changes can result in major impacts on project economics. The viability of this project is greatly enhanced by the high recovery of gold into a small mass yield. In particular the production and intensive leaching of the free gold gravity concentrates will allow over 70 per cent of the gold to be recovered efficiently with minimal impact from preg-robbers. By using flotation the mass of the remaining fine preg-robber contaminated material, to be leached in CIL, is greatly reduced allowing this difficult material to be economically treated. This is an ABSTRACT ONLY. No paper was prepared for this presentation. 

Aug 1, 2010

By H Simpson, C Gimber

The financial evaluation of mining projects drives a whole range of decision-making regarding project viability, project design, operating models and closure philosophy. Net Present Value is a financial assessment approach that is pervasive across the industry and has been widely criticised for driving short-term thinking and leading to poor long-term outcomes and future unfunded closure liabilities. But are there alternative models and what are the impediments to their implementation? This paper aims to outline current and past mine closure practices in the mining industry and questions these outcomes given the changing shareholder investment requirement for alignment with sustainable Environmental, Social and Governance (ESG) goals. Examples are presented of closure programs planned and executed in the later stage of the life-of-mine and explores the benefits that could have been realised by integrating these into concurrent production operations. Examples of simultaneous mine development and closure execution and their benefits are presented, and their relevance to corporate investor branding. This paper also discusses the concept of investor project ownership through to sustainable closure and outlines alternative approaches to responsible, sustainable mine closure. We explore the current mining industry divestment practices to remove closure liability from the balance sheet. These underlying financial practices and Net Present Value approach to Mine Closure and alternative approaches are discussed.

Aug 2, 2023

By R Pax

Feed ore variability, the major disturbance into a mineral processing plant receives considerable attention operationally, and at research and strategic levels to ensure that the throughput of the ore are maintained at all times whilst encouraging a sustainable approach to recovering the valuable minerals from ore bodies. Effort and insights from mineralogical and processing characterisation (eg. ore hardness) of sub-ore body domains allows sequencing for processing to ensure consistency and throughput for the size sensitive grinding unit processes. Optimising the blast fragmentation has benefit as does pre-concentration using ore sorting. Blending of ore domains with different characteristics is common for operations. In recent years a number of technologies have become available for on-line and more rapid assessment of ore and have been discussed in a recent paper by Cameron et.al. (2016) as an opportunity for further utilisation of mine-to-mill (and mine to product) strategies. Current concepts have focused on extensive characterisation of ores so that current control practices can be realised and made more effective with relatively slow measurements and actuation. CITATION: Pax, R, 2018. Dynamic concepts for mine to mill operation and optimisation, in Proceedings Complex Orebodies Conference 2018, pp 124–125 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By G Guy, J Summerville

Over the past five years in coalmine slope evaluation the application of 3D modelling has increased significantly as software has become more user friendly but also areas requiring evaluation have become increasingly complex. Often simplistic 2D Limit Equilibrium modelling and analysis has been poorly used to solve slope stability issues by back analysis and subsequent forward predictive analysis. A plane strain condition with slope movement perpendicular to the slope strike is assumed where in reality the problem is more complex. This often leads to a misinterpretation of the failure mechanism because the failure mechanism being modelled in 2D does not generally represent the actual failure mechanism observed in the pit, with 2D modelling often oversimplifying a slope. This paper presents a case study where the initial slope assessment and remedial design evaluation was undertaken as a 2D Limit Equilibrium model which led to an overly conservative and costly remedial solution being implemented. Subsequent modelling of the slope using both 3D Limit Equilibrium and Finite Element methods were able to provide a better understanding of the structural complexities associated and correlate well with slope monitoring data to create a more realistic outcome.

Nov 29, 2022