Search Documents

By M S. Powell, M P. Bueno

The commonly used SAB, SABC and run-of-mine (ROM) ball mill circuits can achieve high throughputs with good operating stability. However, these circuits consume a substantial amount of grinding media, which can have a substantial impact on the OPEX and the æcarbon footprintÆ, specifically when viewed as an æembodiedÆ energy input. On the other hand, fully autogenous (AG) circuits can operate at much lower operating costs, but with limited throughput. The control of AG mills, fed by ores with hard and soft components, can also be challenging, due to the sensitivity of the mill to the ratio of hard to soft components.In this paper, a multi-component modelling approach was used to demonstrate that the harder component should be used as grinding media, and its use should be kept to a minimum to avoid reduction in the mill throughput. There is an optimal blend of hard to soft, and any optimal blending condition is both ore-dependent and mill-specific. Establishing this blend is challenging, and consequently discourages the use of autogenous mills. The new modelling approach addresses this challenge by providing a quantitative prediction of the influence of blending soft and hard components in a mill. This prediction can then be used to establish the required blend for maintaining a stable and efficient operation in autogenous grinding mode.CITATION:Bueno, M P and Powell, M S, 2012. How to use hard ore components as grinding media, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 31-36 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By R B. Wanty

Historically, most investigations of biogeochemical cycling in acid rock drainage systems involved synoptic sampling over longer time periods (one sample per week or month) or intensive time series studies over a few hours or days. However, many important episodic loading events, such as seasonal meltwater and storm events occur on timescales that are rarely observed by these traditional sampling approaches. Monitoring these transient processes, which may contribute the bulk of the annual metal loading, is essential for accurate assessment in acid rock drainage areas. Recent work also has demonstrated dramatic diel (24 hour cycle) variations in trace metal concentrations in response to diel changes in temperature, pH, oxygen, and photochemical cycling (Brick and Moore, 1996; Nimick et al, in prep). To characterise a system that may respond to diel, seasonal, and episodic events, a monitoring program must sample at a frequency that captures the details of these major forcing events. We developed two novel instruments, the Zn-DigiScan and the DigiSampler to examine low and high frequency temporal changes in acid rock drainage areas. The Zn-DigiScan is a battery powered real time in situ chemical analyser designed for long-term deployments with hourly analyses of Zn. Stream physical parameters (temperature, conductivity, dissolved oxygen, pH, turbidity, etc) were measured every 15 minutes with a water quality sonde. The DigiSampler was developed for the long-term daily sampling of biogeochemically active elements and can take either discrete samples or samples integrated over 24 hours. The DigiSampler collects 2 ml samples in a Teflon coil which are separated by 0.2 ml nitrogen bubbles. The sample coil is returned to lab and the 2 ml samples are diluted 1:10 and analysed for trace metals by ICP-MS. Initial results from a three-day deployment at Fisher Creek, MT, USA have successfully demonstrated the ability of the Zn-DigiScan to record Zn concentrations at levels below 100 ¦g/L. Zinc concentrations measured at 30 minute intervals in Fisher Creek showed a diel cycle with low values of ~25 ¦g/L in the late afternoon and increasing to ~60 ¦g/L by early morning. Zn concentrations were inversely related to temperature and pH, suggesting that temperature and pH dependent adsorption was the main factor controlling diel Zn fluctuations. Initial deployment of the DigiSampler also was successful, revealing diel cycles in Zn, Cu, and Mn. Comparison of trace metal samples collected by the DigiSampler showed good agreement with samples collected by an Isco automated water sampler, demonstrating that the DigiSampler can collect clean samples for trace metal analysis at the low ¦g/L range.

Jan 1, 2003

By S Nowosad, A Binder, O Langefeld, M Bothe-Fiekert, F Apollo

The mining industry faces complex and urgent challenges driven by an increasing demand for raw materials, and a socially demanding globalised world. The extraction of primary raw materials is today more important than ever as one of the cornerstones towards a sustainable future since the increasing demand for the raw materials required for the energy transition. In the last three years, leading countries as USA, China, Canada, Australia, and the European Union (EU) have developed and adopted strategies to enhance domestic extraction capabilities, diversifying sources, fostering innovation in recycling, and promoting international collaboration related to critical raw materials. On 2022, the Inflation Reduction Act was signed into law in the USA, in June 2023, the Australian Critical Minerals Strategy 2023–2030 was published and in March 2024, the Council of the EU adopted the European Critical Raw Materials Act. On the other hand, raw materials extraction is facing higher environmental and safety standards and regulations, as well as scrutiny from the broader public. Regrettable environmental accidents as tailing dam failures or acid mine drainage occurrences have led to a general distrust of mining activities leaving mining companies with the dual imperative of increasing output while implementing sustainability, decarbonisation, and circularity as a core value in their production processes. This challenging environment offers the opportunity to enhance ‘blue mining’ (BM) as a sustainable holistic approach that integrates the principles needed to plan sustainable, reliable, and responsible mines for today’s and future generations by implementing the principles of circular economy (CE). This requires a fundamental shift from the traditional linear economy approach to a sustainable, circular economy strategy. At its essence, BM encapsulates four crucial aspects – energy, ergonomics, water, and circularity and integrates these four aspects into integrative mine planning, defining clear goals and objectives from the ‘blueprint’ of a mine towards a beneficial post-mining activity. Its implementation can lead to maximisation of resources beyond the life of the extractive mine and sustainable use of materials by integrating the principles of circular economy and multiuse mine, see Figure 1. These concepts complement and recognise the need to minimise environmental and social impacts while advancing economic development. Finally, this contribution explains the requirements and challenges of moving from linear to dynamic planning approaches under the BM concept. This way, BM stands as an approach that can contribute to the mining industry receiving necessary approvals and support from society leading to a long-term transformation of the industry’s image.

Sep 1, 2024

By I Doye

Acid mine drainage is a serious environmental problem caused by the oxidation of sulfide minerals responsible for highly acidic, sulfate and metals-rich drainage. Several methods of mine waste management have been developed that reduce liabilities on environment. Layered co-mingling of waste rock with compacted tailings, covers with capillary barriers effect, and co-disposal of waste rock and tailings are these new methods which are used to reduce the formation of acid mine drainage. These methods shield waste rock dumps from oxygen. These techniques could prevent oxidation reaction. In this study, alkaline industrial wastes are used with acid generating tailings to inhibit acid mine drainage. The alkaline wastes selected are cement kiln dust (CKD) and red mud bauxite (RMB). These alkaline materials are used to keep neutral conditions in the fine material layer and to inhibit the metabolic activity of Thiobacillus ferroxidans which catalyses the oxidation of sulfide minerals. A series of timed static leaching tests were performed by reacting samples of mine tailings with two, five and ten per cent alkaline material in order to characterise geochemical balance between liquid and solid phases. Column tests have been set up with oxidised tailings, waste rock, CKD, and RMB. Column tests have been carried out to simulate layered co-mingling, covers, liners, and co-disposal of waste rock and tailings. Column leach tests were conducted in order to investigate the long-term neutralisation potential of alkaline materials and the drainage water quality. Bacteria counting were performed on each sample after testing. The results obtained show that the addition of alkaline materials permit the retention of near neutral conditions in the fine material layer, thus increasing water quality and preventing bacteria development. In fact, the pH results show that the use of five per cent, ten per cent CKD or ten per cent of a mixture of CKD and RMB permit the retention of neutral pH conditions in the reactive layer. At these percent rates, the concentrations of Al, Fe, Cu, Zn, and SO4 in solution are significantly reduced compared to those obtained with the tailings only. In presence of waste rock, the relative position of the fine material layer is important. When the fine material layer overlaying reactive waste rock is composted of reactive tailings with ten per cent CKD and ten per cent (CKD:RMB), a delay was observed before achievement of near neutral pH. The neutral pH conditions remain stable over time. The mixture of CKD and RMB provides a better short-term neutralisation than the use of CKD alone. The use of alkaline materials is beneficial in order to reduce the concentrations of Fe and other metals such as Cu and Zn as well as the number of viable bacteria. The use of ten per cent RMB alone does not involve the neutralisation of reactive tailings. In the cases where the fine-grained layer are below or mixed with the waste rocks, the near neutral pH values are directly reached with ten per cent CKD. However, the pH values decrease rapidly and the number of viable bacteria increases.

Jan 1, 2003

By J Lane, D J. Barker, B Pei

Queensland Alumina Limited (QAL) is the worldÆs largest producer of smelter grade alumina, located in Gladstone, Queensland, Australia. The plant employs evaporative cooling towers for waste heat rejection. Process water requirements include red mud residue disposal, steam venting to the atmosphere and Calcination feed moisture. Raw (untreated) water consumption in 2001 was 37 700 m3/d or 3.8 m3 per tonne of production. The Gladstone region experienced a water shortage in the period 2001 to 2003, resulting in progressive water restrictions. Industry operated under a ten per cent restriction from April 2002 and in November 2002 a 25 per cent restriction came in force. The maximum restriction level of 50 per cent was anticipated for the middle of 2003. Water restrictions of these magnitudes have the potential to result in significant production limitations, which would have major economic consequences for QALÆs owners, customers, suppliers and employees. Therefore it was imperative that measures be found to mitigate the impact of these restrictions. Furthermore, as one of the largest water users in the Gladstone region, QAL had an obligation to the community to minimise water usage as much as possible. A thorough analysis of water usage on site was conducted, focussing on all water streams leaving the plant. The philosophy used was that by minimising water outputs, the inputs would follow suit. Where possible, preference was given to solutions that provided lasting water savings. This occurs when the value of the water saving justifies the project cost, irrespective of water restrictions. By June 2002 an average water saving of 19 per cent was achieved, almost double the required saving. By end November 2002 further projects had increased the total water saving to 29 per cent, mainly through the re-use of GladstoneÆs municipal treated effluent as wash water. Further measures to reach the target of 50 per cent reduction were investigated. The evaporative cooling system was to be replaced with seawater cooling, using cooling towers to minimise the seawater pumping cost. Another benefit of this concept was the ability to dispose of the cooling tower bleed stream with the existing system for neutralised red mud disposal. This would avoid the need for an additional environmental outfall from the plant. In February 2003 the Gladstone region received over 500 mm of rain, which boosted water reserves to five years supply at forecast usage rates. This led to the lifting of all water restriction. As most of the implemented water savings measures are economically viable in the absence of water restrictions, raw water usage at QAL is still less than 75 per cent of pre-2002 levels.

Jan 1, 2003

By P J Savory

Ranger is a uranium mining operation located within one of the most environmentally sensitive regions of Australia. Geology has played an important role in mine planning, operations and rehabilitation since discovery of the deposits 25 years ago. The Ranger orebodies have a reserve total of 166 300 tonnes of U308 including 90 400 tonnes of U308 at North Ranger. At current milling rates these reserves give a mine life greater than 40 years. The uranium is hosted in Lower Proterozoic rocks of the Cahill I ormation and is associated with strong chlorite alteration. In pit grade control involves the use of calibrated probes and a radiometric truck discriminator allowing fast, accurate grade determination of material. Ore is defined at a cut-off grade of 0.2 per cent U308. Mineralised material is defined by the Uranium Mining (Environmental Control) Act 1979 (UMEC Act) at a grade of 0.02 per cent U30s. Natural water levels in the #1 Pit area vary as much as 7.5 metres between wet and dry seasons. Ground water inflow into the pit during the dry season is 600 m3/day. No significant slope failures have occurred in the pit. The environmental impact of mining operations is constantly monitored. Rehabilitation of non-mineralised stockpiles is ongoing. This paper discusses the interaction between geology, hydrogeology, rock mechanics and grade control with the present mining operation.

Jan 1, 1994

Metallurgical accounting can be defined as the monitoring of the valuable metals from the time the ore is broken at the primary crusher until the time that we have the saleable products and residues. The overall purpose of metallurgical accounting is to provide management with up-to-date inform- ation that can be used to control mining and metallurgical oper- ations. The decisions that are taken on the basis of the information that the metall- urgical accounting system provides should result in improved control and, ultimately, increased revenue. The current state of accounting is a result of an extended evolutionary process and will continue as process plants bec- ome more sophisticated. Differences in mine æcall factorsÆ and grade control reconciliation can lead to frustration between the siteÆs geoscie- ntists and its metallurgists leading to a level of distrust in the mill grade. Metallurgical accounting is not included in sufficient detail in undergraduate courses and the acceptable industry standards have developed based on what is considered acceptable to industry personnel and consultants. There is now the AMIRA P754 Metal Accounting, Code of Practice and Guidelines Handbook or reference manual. Computer based databases and spreadsheets have transformed tedious bookkeeping into an important management tool. Over time these standards have improved with developments in analytical procedures, weighing technology and sampling. This paper provides anecdotal examples of problems and improvements observed over a number of years within the gold industry in Australia and overseas.

Jan 1, 2009

By D Michaelsen, S Miller

The Grasberg Mine is a copper and gold open pit mine operated by PT Freeport Indonesia (PTFI) and located in the high equatorial mountains of the Indonesian province of Papua. The climate is alpine/subalpine with little seasonal variation in temperature or rainfall. The daily average temperature ranges from about 2¦C to 14¦C and the annual rainfall in the vicinity of the mine and overburden stockpiles is about 4000 mm to 5000 mm. Mining of the Grasberg open pit will continue until 2014 at which time approximately 2750 Mt of overburden will have been produced. Current overburden production rates are 200 Mt per annum. The current mill rate is 230 000 t/day from the Grasberg pit (190 000 t/day) and the underground operations (40 000 t/day). The acid rock drainage (ARD) issues associated with overburden from the Grasberg operations were identified early in the mining operation. Almost all overburden placed to date has been Potentially Acid Forming (PAF). Laboratory testing has identified four main overburden types: limestone and non-acid forming (Green waste), PAF low capacity (Blue waste) and PAF high capacity (Red waste), and Heavy Sulfide Zone (HSZ), which contains greater than 20 per cent pyrite. Waste type block modelling indicates that at least 30 per cent of the overburden production from 2003 to the end of Grasberg pit operations will be limestone. Strategies are being developed to maximise the beneficial use of limestone through strategic blending and placement for ARD mitigation and control.

Jan 1, 2003

By K Knorr

Desktop X-ray powder diffraction using a D2 PHASER equipped with fast linear detector was performed on several iron ore and mill scale samples. Data were analysed using cluster analysis and Rietveld quantitative phase analysis. The quantitative mineralogy of both materials could be established. Thus the input is provided for understanding the energy consumption and the CO2 emission during iron production. Furthermore, tabletop XRD allows to distinguish iron ore from mill scales and to quantify their mixtures.

Jul 11, 2011

The Henty Gold Mine is a good example of a situation where conditional simulation and optimisation techniques may have useful impact on modelling of mineralisation distribution and ore definition. Much of the gold mineralisation at Henty is concentrated within an alteration zone which is both physically discontinuous and forms only a small fraction of the overall mineralised volume. The alteration units are mappable from diamond drill core and underground workings. Conditional simulation and optimisation techniques for ore definition have found considerable success in the open pit gold mining environment. For many reasons including computational efficiency, lack of consistent geological information, and lack of familiarity with ideas and methods among mine geologists, implementations of these methods in open pit mining have been comparatively simplistic. Modelling is commonly reduced to treating the sample data as a single geologic population. This paper discusses the application of the MP method (a particular implementation of conditional simulation and optimisation) to modelling the distribution of potential ore blocks in the Henty gold mineralisation. The approach allows the mine geologist to model both the spatial geometry of the alteration types and the gold grades associated with each alteration type in a single process. Options allow the geologist to include or exclude underground geological mapping and face sampling depending mainly on the abundance of drill hole sampling and the quality of the face sampling. An optimisation algorithm based on maximisation of profit from mining is used to assist in ore definition.

Jan 1, 2000

More and more coal in Australia is extracted by underground mining methods especially by longwall mining. These methods can be particularly sensitive to relatively small-scale structural discontinuities and variations in roof and floor rock character. Traditionally, information on these features has been obtained through drilling. However, this is an expensive process and its relevance is limited to the immediate neighbourhood of the boreholes. The geological uncertainty remains. Seismic surveying, especially by 3D seismic, is an alternative tool for geological structure delineation with growing credibility. In fact, it is one of the most effective geophysical methods available for identification of geological structures such as faults, folds, washouts, seam splits and thickness changes which are normally associated with potential mining hazards. Seismic data even can be used for stratigraphic identification. The information extracted from seismic data then can be integrated into mine planning and design. In this paper, we demonstrate computer aided interpretation techniques for maximising the information from seismic data and illustrate the ability of seismic reflection methods to resolve localised geological features. Both synthetic and real seismic data obtained in recent 2D and 3D seismic surveys from Australian coal mines will be used. Compared with results obtained with drilling programs, the structural definitions from seismic are of unprecedented quality.

Jan 1, 2002

By T D. H McGrath, O Baker, W P. Staunton, C Ypelaan

"The carbon-in-pulp process has been used extensively in the gold industry since the late 1970s to recovery leached gold from solution. Despite more than 30 years of experience in operating carbon circuits, average gold solution loss has remained at an average of 0.02–0.03 ppm (mg/L), higher than the ‘best practice’ target of 0.01 ppm.Process modelling, such as SIMCIL developed by the Curtin Gold Technology Group (GTG), can provide information on optimum set points; however, manual control of the circuit limits the potential benefits.An automated carbon measurement device, the Scout Carbon Meter, has been developed to allow for automation of carbon concentration measurement, and automated control of the carbon transfer pumps. This paper describes the results from the evaluation of the first two prototypes of the meter.Citation:Staunton, W P, McGrath, T D H, Ypelaan, C, Baker, O and Eksteen, J J, 2016. Optimising Carbon Management - Increasing Gold Recovery and Decreasing Costs with the Carbon Scout, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 225–228 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

A mathematical model for spontaneous combustion of coal with moisture included is presented in this paper. The one-dimensional unsteady state model consists of conservation equations for oxygen, water vapour and inherent moisture of coal and energy for both gaseous and solid phases. A first order Arrhenius reaction rate for oxidation under both pore diffusion and chemically controlled reaction regime is considered. The rate of evaporation or condensation is also considered as a function of temperature of coal, water content of coal and gas streams. The equation of the model is solved numerically by the finite difference technique. Influences of different parameters on the process of spontaneous combustion can be examined by using this model. Also the model can be used to simulate full-scale storage conditions.

Jan 1, 2005

By C Smith, D Lilly

The Lafarge Marblehead Plant in Marblehead, Ohio, USA produces 4.2 million tonnes of sized aggregate yearly. In 1997, a program was instituted to maximise primary crusher productivity through the optimisation of blasting variables and procedures. A proprietary blasting shot report database and the Lafarge production database was statistically analysed to provide guidance in the program. Blasting powder factor (kg/m3) was the main control variable utilised to increase crusher throughput. In 2005, the program was refined to increase the production of certain high margin aggregate sizes and the reduction of fines. The principal blasting component affecting the percentage of high margin size production appears to be pattern area (burden and spacing area). This can be coupled with powder factor to optimise the production rate of high margin aggregate sizes. The size optimisation program incorporates the blasting shot report database, Lafarge production database, statistical analysis and aggregate sampling. A preliminary indication is that the production of high margin sizes (12.7 mm X 4.8 mm, 24.4 mm X 12.7 mm, and 50 mm X 25.4 mm) has been increased seven to 12 per cent utilising these techniques. As an added benefit, blasting costs have been reduced linearly as burden û spacing pattern areas have increased and powder factors have decreased. The program is ongoing and will investigate other blasting procedures and variables including electronic blasting caps to further increase the production of high margin products. The statistical methods involved in the analysis are described in this article for use in other mines and situations. The methods described can be used to optimise crusher throughput, digging rates and product size.

Jan 1, 2007

By I Mason, G Turner, J Hargreaves

One of the key objectives in production from any mine is the minimisation of ore loss and dilution. This can only be achieved when the distribution of ore within the mine is known. The distribution of ore is usually evaluated from a combination of drill hole information and underground mapping data. Three-dimensional models of the ore distribution are then constructed by interpolating grades, contact locations and confirming these estimates through mapping. While the interpolation procedure can incorporate an understanding of the local geological conditions, it is an approximation and thus susceptible to some degree of ore loss or dilution. Naturally, such problems increase in areas of sparse geologic information or greater geologic complexity. Borehole radar offers an approach to decrease the interpolative aspects of modelling by providing a continuous image of some ore contacts. Borehole radar works by building a two-dimensional image of an ore contact from radio waves bounced off the contact from closely spaced positions along a borehole. This image can be imported into Datamine (or a similar design package) and incorporated into geological models of a given ore block. The results of a trial survey from the Mariners nickel mine at Kambalda are presented to illustrate the improved level of detail and accuracy that can be achieved through the incorporation of borehole radar into orebody delineation practice. Once implemented on a large-scale this technique has the potential to greatly increase the cost-effectiveness of long hole stoping at Kambalda, through increased ore recovery and reduced dilution.

Jan 1, 2000

By W Ilahi

Underground metalliferous mining methods often result in the formation of vertical openings to facilitate the extraction of orebodies. These development and production techniques can result in the creation of vertical open voids, which include stopes, orepasses, ventilation raises and other excavations. There are risks associated with the use of mobile plant in the vicinity of these voids, especially during backfilling and when bunds are constructed at the edge of a stope or void. These voids can present unacceptable risks if not adequately managed.

May 5, 2022

By M I. Pownceby, N Karimian, A Frierdich

These may be found with goethite through mechanisms including direct substitution or coprecipitation of nanocrystalline phases. Understanding P incorporation in goethite has significant implications for Australia’s iron ore industry as it lowers their commodity value. The current study tests a novel low-temperature technique to extract P impurities from synthetic goethite phases under O2-free ambient conditions by utilising Fe(II)-catalysed recrystallisation. The objective of this study was to examine the effect of the Fe(II)-catalysed recrystallisation of goethite on the geochemical behaviour (mobility and speciation) of co-associated P. To achieve this, we tracked changes in labile P (aqueous and 1M NaOH extractable) concentrations over time in goethite suspensions which were reacted with Fe(II)aq for 14 days under circumneutral pH conditions and room temperature conditions. Temporal changes in Fe mineralogy were investigated via synchrotron-based X-ray absorption spectroscopy. Iron K-edge extended X-ray absorption fine structure (EXAFS) spectroscopy confirmed goethite as the only mineral phase in P-free treatments while goethite (~86 per cent) and feroxyhyte (~14 per cent) were the main phases in 1.0 per cent P-containing treatments after a 14- day reaction with Fe(II)aq. According to our findings, the treatment of P-goethite with Fe(II) for a duration of 7–14 days, followed by a 24-hour extraction of the reacted solids using 1M NaOH, results in the removal of approximately 79.5 per cent of the initial P content. This removal encompasses both the aqueous fraction (~4.5 per cent) and the surface adsorbed fraction (~75 per cent) from the 1 per cent P-bearing mineral phase. Notably, this approach demonstrates an improvement in P extractability, with approximately a 10 per cent increase compared to the 1 per cent P-goethite sample that was not reacted with Fe(II).

Sep 18, 2023

Production of oic at BHP Minerals Pty Ltd's Cannington Mine commenced in May 1997. The initial sloping blocks at the [nine are located in the upper part of the Footwall Lead lode, and the Hangingwall Lead and Glenholme Breccia lodes. This paper discusses the geological investigations, interpretation and modelling that was undertaken for the Footwall Lead lode production block at Cannington Mine, as well as providing a basic geological introduction to the Cannington deposit.

Jan 1, 1997

By P G Simpson

The Sundance gold mine, located 2.5 km east of the town of Batchelor in the Northern Territiory, has produced over 5300 oz of gold since it was discovered in 1978. Sundance is unique in the Pine Creek Inlier in that the ore is hosted in palaeo-karst detritus and crystalline magnesite of the Early Proterozoic Coomalie Dolomite. This paper presents a summary of the geology of the mine, and describes the methods used during the two periods of mining.

Jan 1, 1994

By Y V. Haarlem, P Coghill, N G. Cutmore, M Millen, I Carter

Due to the low concentration of gold, ore sorting for gold has always required measuring indirect properties, such as density or colour, to allow separation on a rock by rock basis. This only works on an ad hoc, by deposit basis and is likely to be least reliable where it is most required in low grade ores. One candidate technique, Gamma Activation Analysis (GAA) has been demonstrated to directly measure gold extremely accurately in powder samples of around 500gm and is used in the Chrysos PhotonAssay assay system. This method uses a linear accelerator (linac) to generate the X-ray radiation that activates the ore at low levels to emit a characteristic gold gamma ray that is then measured by a radiation detector. CSIRO is adapting this measurement technique to application on a belt at up to 800tph to measure pods of ore. The principal differences between measuring samples and an on-line measurement of pods are the requirement to measure coarse ore (<50mm), to measure a larger volume of ore as uniformly as possible, and to have an open-ended geometry with adequate shielding of the linac radiation source. These issues have all been addressed with measurements of coarse ore reported down to around 1ppm in sub-optimal test conditions. They have been demonstrated for <75mm particles with detectors capable of measuring a large volume geometry continuously. These are projected to allow measurements down to 0.3ppm in more optimum conditions for a 10 second measurement time period where the U/Th content of the ore is less than ~10ppm. Extensive Monte Carlo modelling has demonstrated that adequate shielding can be provided in relatively simple geometries with only 1 right angle transfer in the material handling. Steady progress is being made to reach the technical position required to trial an ore sorting system.

Nov 10, 2020