Search Documents

The grinding of ore to a size that is conducive to the extraction of minerals by leaching or flotation is an essential and expensive component of most mineral-processing operations. Overgrinding results in reduced flotability of the minerals, as well as problems in the filtration and thickening processes, while undergrinding leads to a product in which the minerals have not been exposed, and cannot be leached or floated effectively. Furthermore, coarse material causes settling in thickeners and agitator tanks. It is therefore essential, from the perspective of both operational and extraction efficiency, to grind the ore to an optimum size fraction. A well-run milling circuit will yield a product within a narrow size band and at a high throughput. Although the effective operation and control of milling circuits with their many operating parameters is widely acknowledged as a complex as well as a critically important operation, the benefits of such control are difficult to quantify. This is due to the difficulties in relating more stable operation to increased recovery of the valuable components in downstream processes.

Jan 1, 1993

By McGill RA

The Ranger Uranium Mine is surrounded by a World Heritage National Park. The strict environmental controls under which the mine operates are based on scientific and social requirements. Release of non-process storm runoff water to the Magela Creek during flood discharge and under controlled conditions has been identified as Best Practicable Technology for the operation of the water management system. Social and political factors have limited this release to a wet season with an Annual Exceedance Probability of one in ten. The first-generation trigger mechanism was based on a percentile analysis of monthly rainfall. The second-generation trigger is based on cumulative monthly volume increase in the retention ponds and is considered to be more applicable to the operation of the mine water management system.

Jan 1, 1988

By Miles M. J, Sandy D. A

It has long been known that drilling and blasting operations have a direct influence over productivity and costs of subsequent operations. If mine management is to effectively optimise blasting operations, good information is required on the operating costs of each of the affected operations, together with knowledge of how they are influenced by blasting. In practice it is not possible to do enough repeats of a full scale production blasting experiment to make a statistically significant analysis of the results. By monitoring each blast and subsequent operations in as much detail as possible, enough data will be available to effectively measure the effect of blasting on costs. This gives management an insight into the blast performance and is the first step towards optimisation. An Integrated Blast-related Cost Reporting System has been developed at the Rossing Mine Open Pit, which calculates the total mining cost for each blast. In assessing the total mining cost for each blast, use was made of an.integrated planning and management information system to collect relevant production variables, current operating costs and survey data. An automatic image analysis system was employed to measure the fragmentation of the blasted material in the back of haul trucks. A shovel monitoring system is also under development for use in assessing the muckpile diggability and, in conjunction with an appraisal of shovel component reliability, to estimate the maintenance cost under various digging conditions.

Jan 1, 1990

By P B. Hills, R J. Walton

Narrow vein tabular orebodies are prone to mining induced seismicity. The Tasmania Mine is a complex example of a seismically active tabular orebody, where the contrasting material properties of the host strata and of the orebody itself, serve to exacerbate the seismic response. Analysis of a continuous record of seismicity over a period of seven years has provided significant insight into the fundamental mechanics of the rock mass. Understanding seismicity to permit safe extraction of the orebody has been enhanced by instrumentation of rock mass behaviour in response to mining and mining induced seismicity. It is the purpose of this paper to explore that understanding in respect to the adoption of an alternative down-hole Avoca stoping method for use in particular circumstances.Intensive instrumentation of the Tasmania Mine over a period of four years has provided insight into the behaviour of the rock mass in response to extraction of the narrow vein orebody it encompasses. A range of instruments have been installed in clusters or single installations in order to measure changing stress conditions and the impact of those changes on the rock mass and the reinforcement system.Instruments are often installed in very close proximity to active production stoping. While it has been possible to observe the impact of the mining and mining induced seismicity at very close quarters, instruments installed in these locations are vulnerable to damage and consequently, the level of instrumentation is high. Instruments are continuously logged, typically on a six hourly basis coinciding with the end of regular blasting times. The response of the instrumentation to changed rock mass conditions is considered against the background of development and production blasting and against the seismic record to assess the viability of downhole Avoca stoping.CITATION:Hills, P B and Walton, R J, 2012. Continued observations of rock mass behaviour in response to stoping at the Tasmania mine, Beaconsfield, Tasmania, in Proceedings Narrow Vein Mining 2012 , pp 169-178 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

Blasting is a common practice in mining whereby solid rock is fractured, using explosives, to a more manageable size. The effectiveness of blasting influences a number of downstream activities such as shovel digability, crusher throughput and mill throughput. As the cost of explosives is relatively low compared to milling costs (mainly due to power consumption), blasting practices can be optimised so that the downstream processes are made more efficient, and an overall cost saving made. This is the basis of the Mine to Mill approach. The effectiveness of the blasting is influenced by two main factors, the blasting practices used (eg explosive amount and type) and the geology of the area. As the geology cannot be altered, the blasting practices must be refined to create optimum blasting. Kalgoorlie Consolidated Gold Mines (KCGM) Fimiston operation, located in the heart of the Kalgoorlie Goldfields is the largest gold mine in Australia. Mine to Mill at KCGM has had varied success, with initial positive indications being lessened by a number of factors, including the increase in the amount of voids.

Jan 1, 2003

A novel fracture-plane control blasting technique with particular application in wall-control blasts in mines employing medium to large diameter boreholes is described. It consists of a string of nested holes, each nest consisting of a large diameter charge-hole flanked on either side by a small diameter satellite hole. Each nest is shown to be an analog of a pressurized hole with diametral notches along its length. This 'equivalent-notched' hole concept for generating controlled fractures along preferred directions has been successfully investigated in the laboratory and in the field. The technique has been used to generate controlled fractures on a quarry bench in highly jointed limestone. The resulting blasts with a 250 mm diameter central charge-hole and 50-75 mm satellite holes show that two nests of such holes almost 5 m apart could be joined by a single co-linear fracture. The design range of diameter ratio between charge-hole and satellite hole is 3 to 6 and spacing is 3 to 5 charge-hole radii. With careful matching of explosives and decoupling, and combination of diameter ratio and spacing, it would be possible to connect two nests of such holes more than 20 charge diameters apart by a single controlled fracture plane. The relative merits of the technique against existing wall-control blasts are discussed, and guidelines for practical fracture-plane control blast designs are discussed.

Jan 1, 1990

By Heidecks C

Sub-level stoping with consolidated rockfill is the main method for mining steep dipping baryte and fluorite veins in Germany. Drifting is fully mechanised using drill jumbos, LHD units and shotcrete support. Stopes have heights up to 50 m with sub-level distances up to 15 m. Winning of the pillars between sub-levels is done by longhole blasting in slices of 3-5 m length on strike. Mucking is done on the lowermost level by LHD units. After each blast rockfill with binder (cement and/or fly ash) is dumped into the scope from the uppermost level. Economic success depends on both geological and technical parameters and factors, eg vein thickness and dip, ore grade, size and distance of sub-level drifts. Of particular influence are ore loss in pillar winning and dilution both in drifting on vein and in pillar mining. A comprehensive computer program has been developed for calculating the total cost per tonne run-of-mine ore respectively per tonne of concentrate for a single stope. The cost model includes development, longhole blasting, mucking and haulage to the mill, milling and ventilation. All costs (labour, energy, supplies, maintenance, depreciation and capital cost) are taken into account. Dilution and recovery are both considered. The program can be used to estimate the cost of mining a particular stope. It can also be used to investigate the influence of relevant parameters and factors on the economic result. By this way it should be possible to optimise the technical design of a stope.

Jan 1, 1995

Zinc alloy castings continue to account for a very large, world-wide end-use market for zinc. However, an ever expanding multitude of other materials and processes are increasingly providing viable, cost-effective alternatives to designers, many of whom have no particular allegiance to any one industry. In order to meet this challenge, innovation of and for the zinc hot chamber pressure die casting process, in concert with sustained and inventive market development, is clearly required. While 'Quality' is now the watchword, and the goal of zero defects is being rigorously pursued, other important goals which must be addressed include net shape casting, enhanced productivity and increased energy efficiency. The paper gives an overview of several practical, process-orientated, projects designed to help achieve these goals. For example, a project designed to understand and precisely measure dimensional changes of castings with time has provided some of the critical information needed for net shape casting. A second study is looking anew at surface quality in relation to process conditions as an important step toward the goals of zero scrap rate and increased productivity. Developing the correct die casting machine parameters for achieving optimal quality and properties of zinc (ZA) die castings is a further example of research designed to benefit both the die caster and his customer, chiefly the original equipment manufacturer (OEM). A project on die soldering or galvanising in response to varying process parameters is similarly being considered in order to foster increased understanding and avoidance of problems, with a special interest in the use of special coatings. The maintenance or expansion of the future market for zinc die casting alloys also depends on design for functional applications, as an adjunct to their traditional decorative use. The role that alloys with enhanced properties can play, such as ZATEC, a new high creep resistant alloy developed specifically for elevated stress/elevated temperature applications, will be briefly discussed.

Jan 1, 1993

This paper describes the application of a three-dimensional finite element modelling tool to help assess the stability of a highwall at a Central Queensland mine following the weakening of its base due to highwall mining. With traditional stability assessment techniques, likely failure modes are identified on the basis of previous experience and structural, sedimentological and geomechanical data and a mechanistic analysis of these individual modes is performed. The value of the full three-dimensional model over these traditional techniques is that it provides a coherent approach to assessing highwall stability without the necessity of initially deciding upon the dominant failure mechanism and gives a useful adjunct to the traditional tools. The three-dimensional model assumes the rock mass is made of elasto-plastic blocks, incorporating possible planes of weakness, separated by near horizontal joints. The model includes the relaxation of stresses due to the excavation of the highwall and incorporates estimates of blast damage near the highwall surface

Jan 1, 1995

By Z Li, D Chalmers, J M. Tenney

This paper presents the findings and analysis of the investigation of effectiveness of thin spray-on liners (TSLs) as a gas management tool in underground coalmines. The project involves spraying TSL on the area surrounding gas drainage holes whereby the TSL acts as a thin membrane decreasing the permeability of the coal. This restricts air migrating through the coal seam and diluting gas from the drainage holes. There are a number of potential benefits from this technique but key points are that gas drainage holes produce gas with higher concentrations of methane. The design and execution of a field trial to investigate the effectiveness of a TSL on purity of in situ methane from gas drainage holes is presented in this report. For eight drainage holes, the results show an average increase in methane purity by 9.14 per cent and a reduction in air contamination by an average 7.93 per cent. Overall methane flow rate decreased by 27.6 L/s; however, flow rates were unreliable due to poor measuring equipment. For most holes, methane purity was not changed significantly; however, certain boreholes were responsible for most of the variation in methane purity. The boreholes showing a dramatic improvement in methane purity were likely those with intersecting cleats covered by the TSL. If the TSL was sprayed over more area, specifically in areas where the cleats are intersecting with holes, it is likely that purity of methane in the drainage holes will increase.CITATION:Tenney, J M, Chalmers, D and Li, Z, 2015. Thin spray-on liners potential in reducing dilution of in situ gas in underground coalmines, in Proceedings The Australian Mine Ventilation Conference, pp 323–328 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

Alluvial gold exploration is aimed at recognizing areas of anomalous gold content as evidenced by the nature of the drainage system, its age, geomorphic history and other features of the geological environment including the provenances. Subsequent studies to quantify the findings are governed by the need for accurate data based upon precise measurements. Computerization allows the use of more complicated mathematical procedures than are feasible manually, thus promoting the development of more advanced technological aids. Data banks provide the means of storing vast quantities of information for instant recall.Sample representivity is a major problem and a clear understanding of both sampling and analytical requirements is essential for dealing with problems arising from variations in sample size and particle size distribution. Field samples must always be large enough to ensure adequate representivity or the sampling has failed in its purpose.

Jan 1, 1984

Swedish sulphide mining is presented. Dry filling is described. Fill properties with and without cement addings are dis- cussed in relation to various studies in la- boratory and in situ.

Jan 1, 1973

By Johns A. L

The concept of the Melbourne Underground Rail Loop and the organ- isation to achieve its construction are covered in the companion papers (Reference 1, 2) and will not be repeated here. The Victorian Railways, as well as being the eventual operator of the Loop when it is completed by MURLA, have also been responsible as "Contractors" to MURLA for the construction of the "cut and cover" or "box" tunnels and related approach works located on existing Railway property. These tunnel connections link the existing suburban system to the new underground works. The following tabulation indicates the significant work volume involved in this cut and cover tunnelling exercise and which is covered in some detail by this paper.

Jan 1, 1981

By Hammond J. R, Ward T. A

The Tom Price orebody, in the Hamersley Ranges of North West of Western Australia, is mined by Hamersley Iron Pty. Limited. The orebody is a folded sequence of hematite and shale bands capped with goethite, with a con- sequential variable iron content. The overall grade is below that required to yield spec- ification product, necessitating selective mining, 'Zone Plans' based on geological structure have been developed to yield forward information on material types and grades. Short and medium term mine plans - the initial stage of quality control - are based upon these 'zone plans'. Blasts are laid out to break to the grade boundaries, thus minimising dilution, and the samples taken from the blasthole cuttings provide blast grades. Blending of shovel out- put from different blasts forms the operational basis of grade control. Shales, being more friable than hematite, produce fines that are lower in iron grade than lump. Quality control in the mine centres around maintaining the target fines grade, compensation being applied in the mine if the fines grade lies outside the target range.

Jan 1, 1973

By Koh P. T L, Varnas S. R

Fluid flow, heat transfer and combustion in a nickel flash smelter have been investigated by numerical modelling and flow visualisation. The three-dimensional numerical model incorporates turbulent two-phase fluid dynamics, radiative heat transfer and combustion. The main features include the use of the k-E turbulence model, the Lagrangian tracking of particles, radiative heat transfer based on the spherical harmonics method, and chemical reactions. The predicted flow fields are in good agreement with data obtained from a series of flow visualisation experiments on a cold water model. The interaction mechanism between the fluid flow and the solid particles is examined for a range of particle sizes both with and without injected oil in a series of simulations. The heat transfer in the shaft is dominated by combustion and radiation, whereas the ignition of particles is influenced by the particle size and the added oil. Flow and temperature fields for both gas and solid particles are presented as well as the fraction of sulphur removed from the particles.

Jan 1, 1992

By Sowerby BD

The CSIRU Division of Mineral Engineering is developing various techniques for the on-line determination of moisture in coal and coke, and some instruments are now commercially available. These techniques permit accurate and rapid determination of moisture in materials directly on conveyor belts or in bins. The most promising techniques for direct on-belt measurement of moisture in coal are capacitance and microwave transmission. A non-contacting under-belt capacitance and gamma-ray backscatter technique has determined moisture in coal to better than 0.5 wt'/. in field tests at BHP Stockton Borehole Colliery, NSW. Mineral Control Instrumentation Pty Ltd have been licensed to manufacture the capacitance gauges and have installed five commercial units in the coal industry and other industries. Microwave transmission techniques have an advantage over the under-belt capacitance technique in that they are not sensitive to vertical segregation of moisture in coal on the conveyor belt. A laboratory prototype of a microwave transmission gauge has been constructed and tested. Microwave techniques, based on a measurement of attenuation and phase shift, are under development and are expected to be field tested in 1987. These new techniques will enable a wide range of thickness changes to be accommodated. Capacitance and microwave transmission methods are unsuitable for materials of high electrical conductivity, such as coke. CSIRO is therefore developing a fast neutron and gamma-ray transmission technique, which is proving very accurate in laboratory tests. This technique overcomes many of the limitations of thermal neutron moisture gauges and it is expected to be field tested in 1987.

Jan 1, 1987

By B Arthur, K Sexsmith, D Hockley, S D

At the proposed Crandon Project, mill tailings would be depyritised for upland disposal. The resulting pyrite concentrate would be disposed of in the underground workings as a cement-amended paste backfill. In the long term, the underground workings would be flooded and the potential for the paste backfill to generate acid would be limited. However, while the mine is operational, there is potential for oxygen ingress to the backfill that may lead to sulfide mineral oxidation and acid generation. A series of humidity cell tests were completed to assess the potential for groundwater contamination. To assess effects of surface area on oxidation, the humidity cell tests were conducted on moulded cubes of paste backfill. The tests were terminated at different intervals, and the cubes were dissected and examined mineralogically. Various leach extraction procedures were also used to assess the progress of oxidation and secondary mineralisation within the paste backfill. The test results showed that: the cement amendment significantly contributes to acid neutralisation and results in a lag in excess of one year before the onset of acidic conditions (in comparison to less than three weeks for the pyrite concentrate); the depth of oxidation in the paste backfill is restricted to about 1 mm after 107 weeks of testing; and secondary minerals form a distinct ærindÆ at the surface of the paste backfill. The results indicate that acid generation in the backfilled stopes would be minimal. The importance of including the surface area effect in the testing (ie using moulded cubes) is clearly demonstrated.

Jan 1, 2003

By Trois P

A fully instrumented and bench-mounted diamond drilling machine, purpose designed and built, has been used for investigating the effect of aqueous solutions of various chemical compounds when used as drilling fluids. The rocks investigated were andesite, basalt and granite, the chemical compounds were alkylamines, with various hydrocarbon chain lengths, aluminium chloride and dioxane. Rotation speed seems to be one of the major factors affecting the emergence of mechanochemical effects as the results obtained with aluminium chloride clearly indicate. Penetration rate is either unaf- fected or enhanced by the presence of certain compounds, such as aluminium chloride. On the other hand, penetration rate diminishes when the drilling fluid contains dioxane and exhibits an apparently unpredictable behaviour with alkylamine solutions, although it appears that an increase in hydrocarbon chain length usually equates to an increase in penetration 1. Full Professor, Mining and Mineral Dressing Department University of Cagliari - Italy 2. Associate Professor, Mining and Mineral Ikea- sing Department University of Cagliari û Italy rate. Rock texture seems to have a pronounced effect on test repeatability. With hexadecy- lamine acetate solutions in concentrations ranging from 10-5 to 5 .10-4 molò dm 3 and 41.88 radòs-1 rotation speed, 46 % increments in penetration rate of andesite were observed, with respect to water, whereas penetration rate decreased in basalt by as much as 60¦%o when a dioxane solution was used as drilling fluid. An interpretation of the observed effects is proposed in the light of current knowledge of solid state physics and physical Chemistry.

Jan 1, 1992

By Thomas G. A

THE irregularity of the Mount Morgan (Queensland) ore body presents problems other than those only of mining. For irregularity of outline is coupled with irregularity of grade, and the ore varies so rapidly from profitable to non-profitable, and fromhighly siliceous to highly pyritic, that the task of estimating quantities and values of ore reserves is manifestly rendered a difficult one, while the actual disposal of the broken ore demands constant supervision.Four classes of ore are handled. The oxidized ore, cheaply mined and cheaply treated, is obtained by quarrying from the top of the mountain. Below the 315-ft. mine level (measured from the original summit) sulphide ore comes in, and this is divided into siliceous sulphide ore (too siliceous for economic smelting), sulphide ore suitable for smelting, and ore too poor either to be smelted or to be treated by wet process with the siliceous ore. It is with these three latter descriptions of ore that this paper principally deals.Although the output from many stopes in the mine may usually be presumed beforehand to be either smelting or wet-treatment ore, yet it is never safe to take this for granted, and constant assaying is necessary. At the same time the ore merges from one class into...

Jan 1, 1911

By A J. Daniels

Macraes Mine is a large-scale open-cut and underground gold mine located in Central Otago, on the South Island of New Zealand. This paper presents the role of geological mapping in the grade control process at Macraes Open Pit as a case study, and demonstrates how systematic geological mapping can add significant value to the mining cycle. Geological mapping has proved to be a valuable foundation for orebody interpretation and analysis.Practical applications and lessons learnt are summarised, including predictive control of the orebody, improvement of geotechnical modelling, and identification of further exploration targets.

Aug 22, 2011