Search Documents

By C MacRae, N Wilson

CSIRO Minerals has recently developed an electron microprobe (EMP) based imaging (or mapping) method for characterising ilmenite concentrates. The method requires an electron microprobe analyser to collect elemental X-ray maps which are then processed via an in-house developed software module (CHIMAGE). The type of information readily available from EMP mapping includes; primary phase identification, modal analysis of phases, chemical analysis of individual phases, textural information (eg the alteration stages in the formation of leucoxene or pseudorutile from primary ilmenite and the development of macro-porosity), and the identification of coatings or pore-fill material. All of these parameters will impact on the choice of future downstream processing options considered for any particular ilmenite concentrate. The method has been demonstrated to be a sensitive analytical tool for assessing the distribution of aluminosilicate minor impurities in ilmenite feedstocks from the West Coast of Australia and also for characterising the complex chrome-spinel gangue phases common in East Coast ilmenite concentrates from the Murray Basin.

Jan 1, 2001

By J E. Moffatt, N A. Spooner, T J. de Prinse, D J. Ottaway, E Klantsataya, L d. S Teixeira, B W. Smith, T B. Payten, G Tsiminis

Single wavelength fluorescence sensing has been used in the preconcentration of ores for many years in situations where it is typically specific to the mineral of interest. Examples of fluorescence sensing include the sorting of diamonds in diamond mines and the sorting of scheelite in tungsten ores. However, the number of minerals that show useful single wavelength fluorescence properties in the visible spectrum is relatively small, so the application of fluorescence sensing is currently limited to niche application in the minerals industry. Recent developments at the University of Adelaide have focussed upon extending fluorescence signal measurements into the infrared spectrum, as well as investigating multi-wavelength fluorescence known as up-conversion fluorescence. These techniques may not only significantly increase the number of minerals that exhibit fluorescence properties suitable for both identification and sensor-based sorting, but also provide mineral-specific signatures of higher quality than previously attainable. This paper details the research work carried out by the University of Adelaide and funded by CRC ORE to develop a mineral-specific fluorescence sensor. The sensor targets two fluorine bearing minerals, fluorite and fluorapatite, that are common in many base metal ores such as porphyry copper ores and silver/lead/zinc ores. Fluorine is a known penalty element in mineral products derived from these ores, so mining companies need to monitor and control the amount of fluorine in their final product to keep it below commercially agreed specifications. Currently there is no real time sensor capable of monitoring fluorine in the ore feed so monitoring and control is carried out using time-consuming standard sampling and off-line laboratory measurements. The development and application of a real time fluorine sensor will enable the mining companies to monitor and control fluorine levels in the plant, greatly reducing the time and cost associated with producing their mineral concentrates within the prescribed specifications.

Nov 10, 2020

By R Justa Cámara, L M. Pinillos Lorenzana

Barcelona Metro Line 9 (Line 9) is an essential infrastructure, improving the transversal transport in Barcelona by connecting the greater part of the currently existing radial lines. The purpose of Line 9 is to create a peripheral line surrounding the city of 1.6 million people (metropolitan area exceeds five million), and includes 52 stations, of which a total of 32 are deep shafts and 19 transfer stations in a densely populated area with several geographical constraints.The tunnel has an inner diameter of 10.90 m, bored with an earth pressure balance (EPB) tunnel boring machine (TBM) in soil sections with precast concrete lining type universal ring and segments 40 cm thick.A single tunnel solution was adopted, driven by functionality and costs savings. The internal tunnel section is divided into two levels to allow for one way rail transit including the platforms in each station on each level in order to optimise the space created by the TBM excavation and comply with the operational needs. The division in two areas of the tunnel was carried out through the construction of a horizontal slab resting on the tunnel segments with a constant thickness of 40 cm at the central part of the slab and supporting side walls.CITATION:Justa Cámara, R and Pinillos Lorenzana, L M, 2014. Two transit levels in one tunnel tube – an innovation in Barcelona Metro Line 9, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 387–398 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By J Joughin, D Kyan, L Rollin

In line with the 2015 Paris Agreement and corresponding climate disclosure requirements, many mining companies have publicly disclosed that they are developing and/or implementing ambitious decarbonisation strategies. Sometimes these strategies can be linked to the development of community programs and/or the creation of a positive legacy post-closure. Renewable power is key to most decarbonisation strategies – some mines will get this from external sources and others will establish on-site power generation and storage facilities. A range of options are available to develop renewable power generation (eg solar panel, wind farm, hydropower) and energy storage (eg battery, hydrogen, pumped hydroelectricity). Land access, impact assessments, planning and environmental approvals are required to establish new facilities. Host communities are more likely to be in favour of, or at least will accommodate, new power supply developments if these are planned with a benefit to the communities. Transitioning to renewables raises new challenges. Among these are high upfront costs and access to capital, energy demand variability, supply intermittency and variability, storage limitations, grid stability and reliability, transmission and distribution infrastructure constraints. Compounding these challenges are issues such as infrastructure resilience to extreme weather events (eg heat, wind), land use and access, lengthy permitting processes, community perceptions, skilled labour requirements, and meeting mine closure objectives. Renewable energy sources provide a more decentralised source of energy that reduces reliance on imported fuels, thereby increasing energy security and lowering production costs. On the contrary, implementing renewable energy could lead to potential negative impacts such as visual perception from the community, competitive land usage, electricity price raises due to upgrading infrastructure and the use of electricity storage capacities. As part of the definition of an environmental and social management plan, participative stakeholder engagement is required to identify benefits to the communities. For example, among the recognised benefits of developing solar panels (increase job opportunities, reduce soil erosion), various technologies have been experimented globally for the last ten years and are emerging due to their proven community benefits. Key findings to enhance those benefits can range from the development of innovative practices such as ‘agri-/aqua-voltaic’, ‘solar grazing’ to optimise land usage and stimulate the local economy (Table 1), to the implementation of technologies providing services to communities such as mobile water desalination plants or ‘smart grid’ systems to minimise energy clipping during peak-load of oversized renewable energy facilities (Table 2). While developing those synergies, careful management is required to avoid creating superfluous energy service needs from community programs. Energy sufficiency should remain a key principle according to the sufficiency, efficiency and renewable framework of the Intergovernmental Panel on Climate Change. Darby and Fawcett (2018) define energy sufficiency has ‘a state in which people’s basic needs for energy services are met equitably and ecological limits are respected’. Sufficiency tackles the causes of the environmental impacts of human activities by avoiding the demand for energy and materials over the life cycle of buildings and goods. Efficiency tackles the symptoms of the environmental impacts of human activities by improving energy and material intensities. The third pillar, renewables, tackles the consequences of the environmental impacts of human activities by reducing the carbon intensity of energy supply (Cabeza et al, 2022). Life of Mine Conference 2023 | Brisbane, Australia | 2–4 August 2023 34 This paper provides project developers, decision-makers and regulatory authorities with ideas on synergies between renewable energy options and community development programs. These can be considered to enhance stakeholders’ support for implementation of decarbonisation strategies.

Aug 2, 2023

By R van Wyk

In today’s mining environment the use of heavy mechanical devices and other high-tech electronic devices like two-way radios, cellular phones and even automated mining systems, form a vital part of the daily operations of a mining site. These human-made devices and some of the naturally occurring events, like lightning and gamma radiation, can have negative effects on electronic detonators and the associated control equipment.On larger mining operations the necessity to move the point of safety for blasting further away from the blast area, introduced remote firing via radio frequencies for electronic detonator systems. Other influences on electronic detonators can be abuse or ignorance. To ensure the safety of the end-user, an electronic detonator must be resistant to some common mistakes that users can make. One of main concerns here is resistance to static discharge or incorrect wiring. Despite the daily use of electronic detonator solutions, scepticism and concern still exists amongst those who believe the system raises the risk of a premature initiation of the blast through some form of interference trigger.This paper will help users understand how electronic detonators and the associated control equipment protects itself from external influences. Focus will be on protection schemes to counter static and over-voltage discharge and methods to ensure protection of secure wireless radio links and detonator communications. With well engineered communication systems and solid static and over-voltage protection, an electronic detonator system can be more reliable and safer than other detonator systems. The following main points will be discussed:what makes a detonator an electronic detonator,static electricity and over-voltage protection,the general influence of electromagnetic energy on the detonator,the influence of lightning on detonators,the protection of radio communication’s links as used by remote firing equipment, andthe safety protection features built into remote firing equipment.

Nov 8, 2011

By D Connelly

As the resources sector becomes tougher with rising costs and cyclical metal prices, mining companies need to continue to reduce their costs and do more with less. Many new resource projects fail to come in under or on budget based on Feasibility Studies. Particularly, capital expenditure (CAPEX) proves difficult to achieve for resource projects. A number of resource projects have failed because of aggressive plant CAPEX cost cutting resulting in projects with no surge capacity and are unable to achieve design throughput. In addition, the plants are not operable because of the omissions. In recent times many businesses have also experienced the "costs" of simply implementing aggressive operating "cost cutting” measures as a strategy for solving business performance problems. This paper looks at technology driven, employment related, luxury cuts, department cuts and restructuring cuts. In the past companies used an incremental approach based on the use of past budget information as an integral part of the budget construction process going forward. The use of performance reports and Management Information Systems (MIS) is examined along with the role of continuous improvement in achieving sensible cost cutting.

Aug 8, 2011

By N Mangadoddy, P Jampana, S Diddi

The study of air-core dynamics in hydrocyclone operation is essential for predicting separation efficiency in mineral processing. Electrical resistance tomography (ERT) allows non-invasive measurements of hydrocyclone internal flow dynamics. Existing regularisation methods such as Gauss-Newton and TV norms rely on optimisation techniques which have very high computational cost for very fine meshes. In contrast, the monotonicity method has much lower computational cost as it does not solve such minimisation problems. In this paper, results from the monotonicity method, Gauss-Newton (GN) (Tikhonov) and Total-Variation (TV) norm-based minimisation methods for estimating the air-core diameter in hydrocyclones are compared. We study these methods on the laboratory hydrocyclone experimental two-phase flow data. The results obtained are validated against High-speed video (HSV) imaging and Computational Fluid Dynamics (CFD) results. The results on different mesh sizes, in particular for very fine meshes with the number of cells ranging from 30 000 to above 100 000 are also investigated. The data used in this study is obtained from ITS Z8000 ERT system. This system does not measure the voltages on the current carrying electrodes. Since these voltage values are required for the monotonicity method, we implement an interpolation method to compute them. The results show that the monotonicity method provides a closer approximation of the interface between air and the water phases.

Aug 24, 2022

By L Bertoss, D Carvalho

In the last decade, the use of advanced implicit modelling software/algorithms in mineral resource workflows has become a best practice in the mining industry. In most cases, these workflows can easily replicate the level of detail of explicitly modelled geometries, even for very complex deposits. These techniques are flexible and can produce fast results since software is responsible for generating 3D surfaces and solids based on geological and interpretation data. Nevertheless, depending on how unique and complex some deposits are, intense manual editing and input are required to honour the geological context and produce the desired outcome. The current geological modelling workflow at George Fisher Mine (GFM) is based on the semi-automatic built-in tool that generates stratigraphic sequences (stacked lithology layers) based on logging and mapping data. This tool (stratigraphic sequence from Leapfrog Geo™) works for the majority of areas in the mine but fails to capture observed mineralisation pinch-outs in operational areas and at extrapolated boundaries of the deposit. These pinch-outs have the potential to negatively impact grade forecasts if not resolved manually. Using built-in software tools only, the alternative for a more accurate model is to generate each individual layer and adding tens of thousands of manual interpretation points to honour pinch-outs (based on the amount of existing drilling in the mine and number of layers). This approach would require an estimated minimum of two to four years of a full-time employee (FTE) to be exhaustively completed. This study presents an automated approach to generate pinch-out points using a set of Python scripts that only take a few minutes to run. The newly generated points are then combined into the commercial software workflow as interpretation points, honouring observed pinch-outs. The remarkable time difference between approaches removes chance of manual errors and allows mine geologists to spend valuable time in validation and testing of scenarios, ensuring they are more representative of the deposit’s geology.

May 24, 2023

By J E. Everett

Maximising ore tonnage at a selected target grade requires that appropriate ore identification criteria be established. Iron ore mining block models may consist of many millions of estimated blocks, each block corresponding to the selective mining unit (SMU), with grade interpolated from drill hole data. Each block can be considered as a potential ore candidate. Analysis of such a huge database can require large computational resources, especially for sensitivity analysis requiring multiple computations. However, an alternative streamlined approach is possible, where the data are compressed to an appropriately smaller and representative subset. The consequent data reduction not only makes it feasible to consider the simultaneous analysis of multiple pits but also considerably speeds up computation, enabling sensitivity analysis of the potential ore tonnage as a function of the required grade. Ore identification criteria can be successfully established using appropriately chosen reduced data comprising less than one per cent of the blocks. The ore identified is virtually indistinguishable in tonnage and grade from the ore that would be selected using the entire block model.Two methods of data reduction are tested: sampling (using a proportion of unaltered blocks) and binning (consolidating groups of blocks to a single average grade). The source blocks are first sorted (such as by location, analyte grade, principal component score, random order or value) before sampling or binning. In this study, the sorting options considered were by location and Fe grade. The effectiveness of each method was evaluated using the block model subsets to select the maximum tonnage of ore at a specified target grade. Block model data from an anonymous Pilbara iron ore project with about one million blocks averaging 1.132 kt were used. The blocks are from multiple resource models, to be blended to a single product. Sampling is shown to be superior to binning because sampling preserves the full variability while binning, although matching the mean block grades reduces their variability.It was found that the appropriately sampled data sets (sorted by location) gave results virtually identical to the results for the full data set, even when the samples comprised less than one per cent of the original blocks. The reduction in computer time to identify maximum tonnage at a specified grade was approximately proportional to the sample percentage. The increase in computation speed greatly facilitated sensitivity analysis. A sampled data set of one-eighth the total block model was used to investigate the effects of changing each of the component grades around the original grade specification. The results of this sensitivity analysis are discussed, and illustrate the potential benefit of carrying out sensitivity analysis in determining feasible and marketable product grades.CITATION:Everett, J E, 2015. Block model data reduction and sensitivity analysis, in Proceedings Iron Ore 2015, pp 263–270 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By H Mischo, M Ferber, M Donner, B Jung, S Grehl, A Dietze

Mobile robots have been making impressive inroads in a variety of domains. Within the Mining-RoX project, Technical University Bergakademie Freiberg is exploring a further frontier for mobile and autonomous robots: underground mines. The potential benefits of mobile robots in underground mining are plentiful as underground mines are strenuous and potentially dangerous working environments for humans. A higher degree of automation, with robots either acting as helpers for human miners or even replacing all human personnel deployed underground, could help to significantly reduce mining costs. In disaster cases, rescue robots could help to find missing personnel. Unmanned mines operated by robots alone would not endanger human lives at all. Further use cases, and a particular focus of the Mining-RoX project, are mobile robots that gather sensory information of the underground mine (eg for the purpose of creating detailed 2D and 3D maps) as well as monitoring environmental conditions such as air and water quality. This paper presents the design of a prototypical mobile robot for mapping and monitoring underground mines. A generic robotic platform was extended with various 2D and 3D imaging devices as well as other sensors. First results from test runs in an underground mine are reported. Maps of two sections of the mine enhanced with localised sensor measurements were successfully created.CITATION:Grehl, S, Donner, M, Ferber, M, Dietze, A, Mischo, H and Jung, B, 2015. Mining-RoX – mobile robots in underground mining, in Proceedings Third International Future Mining Conference, pp 57–64 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By Griffin PT, Espinosa-Gomez R, Jameson GJ

Two major issues are to be addressed in the Copper Concentrator of Mount Isa Mines Limited. The first of these is the need to increase concentrator flotation capacity to increase copper recovery, while the second is the need to reduce the iron sulphide dilution to meet future smelting requirements. Extra capacity in the cleaner and retreatment sections of the concentrator have been identified as key target areas, with additional copper recovery of at least one per cent identified from plant trials. Extensive pilot plant tests have been undertaken to evaluate the performance of the Jameson cell compared to conventional mechanical cell and column circuits. This work has shown that Jameson cells present an opportunity to achieve the desired grade and capacity specifications at lower capital cost than available alternatives. This paper outlines metallurgical results of work undertaken in the Copper Concentrator, together with a summary of pertinent Jameson cell operating parameters investigated during the period.

Jan 1, 1993

By T N. Little

This paper is concerned with the influence of engineering geology on design of Wall Control Blasts. In the Introduction, the Blast Management Framework and the Blast Design Requirements classification system (previously developed by the author) is drawn upon to set the context. Blasting objective for all wall control blasts involves both profile and damage control. Four classes of approaches for blast design are outlined and briefly discussed. Five distinct wall control blasting techniques are summarised. The general relationship between geology and blast design is explored in the paper. Influence of geology on pre-split and post-split design and blasting direction is highlighted. Wall damage modelling from the closest row of blastholes is also introduced using the Analytical Damage Model (ADM). The relationship of rock properties and explosive selection and in particular the Mach wave generation is introduced to assist blast designer in this regard. Finally a Conceptual Model that relates vibration, damage and rock mass condition has been presented along with some applications that have been undertaken by the developer. Eight conclusions have been formulated based on extensive work in this area and the current study.

Jun 22, 2022

By M Thompson

"The Jaguar concentrator, 60 km north of Leonora, Western Australia (WA), consists of a standard closed circuit semi-autogenous grinding (SAG) and ball mill producing a float feed of approximately 60 micron at 70 t/h. Following comminution, separate copper and zinc concentrates are produced by differential flotation. These concentrates are subsequently dewatered by thickening and then filtration.Separate audits of the Jaguar Operation’s copper and zinc concentrate thickeners were conducted to evaluate their performance, following occasions where site personnel had identified unnecessary loss of copper and zinc concentrate to the thickener overflow. The feedwells were identified as the source of the observed problems due to the following issues with their design/duty:lack of retention time in the feedwell as current design is completely opennot conducive to effective mixing required for efficient flocculationdiameter of the zinc concentrate thickener feedwell was undersize for its duty.To improve the performance of the thickeners, it is planned to replace both concentrate thickener feedwells with a high rate design for their respective duties in February 2016. The audits also identified that the feed system requires modifications with particular importance placed on minimising air entrainment of slurry into the thickener feedwell. Minimisation of air entrainment is hoped to be achieved by providing constant head pressure through installation of weir arrangements in the feedboxes and redirecting each feed pipe so that it feeds tangentially into the feedwell. In addition, improvements to the control philosophy of both thickeners will be made with the installation of an ultrasonic bed level probe and bed mass sensor, in order to make real-time adjustments to the underflow pump speed to maintain steady state operation.Following the feedwell replacement and modifications to both thickeners it is expected that losses of recovered copper and zinc will decrease to undetectable levels. Subsequently it is anticipated that a more consistent, homogenous underflow can be produced for downstream filtration.Citation:Thompson, M, 2016. Concentrate Thickeners Feedwell Replacement, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 273–278 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By M Hilden, K Barbosa, M Yahyaei, C Ndimande, K Runge, V Jokovic

Classification devices provide a link between comminution and flotation. Basically, it determines which particles are diverted back for additional grinding and which ones pass to downstream flotation. Therefore, the classifiers play an important role in the performance of a mineral processing circuit. Hydrocyclones are the most common classifiers used in wet grinding, despite being associated with poor classification efficiency. Hydrocyclones are widely used due to advantages related to low maintenance as well as reduced capital and operating cost. Other classifiers, such as fine screens, have much better classification efficiency compared to hydrocyclones. The major challenge of using screens in an operation, however, is their large footprint and increased maintenance requirements relative to hydrocyclones. Some researchers have demonstrated that switching from hydrocyclones to screens, as the classifier device in a ball milling circuit, resulted in a 20 per cent increase in plant throughput and significant improvements in coarse particle recovery, resulting in a 6 per cent increase in overall flotation recovery. However, it is known that these benefits of improved classification are very much ore specific, ie depending on the ore response. Therefore, there is a need to estimate the benefits of improved classification in pilot scale testing before the plant could consider the potential classifier upgrade. This paper presents the results of two pilot-scale grinding tests where the ore sample was processed using different classifiers: a traditional hydrocyclone and hybrid classification involving the use of a semi-inverted hydrocyclone followed by a screen. The size specific energy and circulating load were used to compare the performance of the grinding circuit. The grinding product was subject to mineral liberation analysis and the impact of classification efficiency on the mineral liberation is discussed in the paper.

Aug 24, 2022

By J Bolen, I Cameron, M Huerta, M Okrutny, K O’Leary

As greater amounts of fine iron ore concentrates enter the marketplace, new investments in iron ore pelletising capacity are inevitable to deliver these concentrates to steel industry consumers. When investors assess the two well-proven pelletising technologies, the straight grate and grate-kiln, the most appropriate choice may not be immediately evident. Certain technical, market and site-specific factors will favour one technology over the other; investors need to be aware and understand these factors in order to make the best investment decision. Hatch has compared the merits of both technologies regarding plant configuration; type of iron ore processed; energy consumption and flexibility to use a variety of fuels; ability to produce the required pellet quality; required plant capacity and scale; operating and capital costs and environmental performance. A technology assessment checklist that investors should consider when making a new pellet plant investment decision is presented.CITATION:Huerta, M, Bolen, J, Okrutny, M, Cameron, I and O’Leary, K, 2015. Guidelines for selecting pellet plant technology, in Proceedings Iron Ore 2015, pp 45–52 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By R G. Reddy, A Yahya

The sulfur distribution ratio (Ls) is an expression of the amount of sulfur in slag to the amount of sulfur in molten metal. The sulfide capacities calculated from Reddy-Blander (RB) model were used to calculate the sulfur distribution ratio (Ls). A new Reddy model for sulfur distribution ratio (Ls) was developed for modelling Ls for ironmaking, steelmaking, and secondary steelmaking conditions. Besides calcium oxide, the major component in the ladle furnace (LF) slags is alumina. The Ls was calculated for typical LF slags as a function of temperature and composition. The model calculated Ls values are in good agreement with the experimental and industrial slags data. The extremely low oxygen potential in these furnaces after fully-killed steel is favourable for desulfurisation. For any given slag’s composition and temperature, its sulfide capacity can be calculated a priori. The equilibrium sulfur distribution ratio between this slag and liquid metal in a particular vessel can also be calculated a priori. The Ls for ladle furnace (LF) slags is about twice those for blast furnaces (BF) slags and ten times those of basic oxygen furnace (BOF) slags. The desulfurisation of pig iron in BF and desulfurisation of steel in LF during secondary steelmaking are recommended. Steel desulfurisation in steelmaking furnaces is not effective. Since the model used to calculate the sulfur distribution ratio (Ls) is a priori, it is a useful tool for the iron and steel makers in improving the product quality and optimisation of the industrial furnace operations.

Aug 21, 2024

By V Rimal, d M. Tangstad

Multiphase slags form the basis of the reduction pathway for manganese ferroalloy production. The present work aims to understand the flow of slag through the coke bed based on experimentation in controlled conditions. Synthetic slags of different basicities were evaluated for their phase composition, viscosity, and flow. The two-phase slag will have two zones: a liquid slag zone and a multiphase zone. The multiphase zone will consist mostly of a solid phase with some liquid slag between the solid particles. The multiphase part will hence have a high viscosity. The liquid zone will flow into the coke bed while the multiphase area will stay. With increasing reduction, the multiphase area will decrease in size until the solid phase is gone and the whole slag will flow into the coke bed. The effective viscosity of slag will decrease with the lowering of the solid oxide phase. The results from flow experiments confirmed that the segregation of phases occurs when slag flows through the coke bed. It is observed that the flow is dependent both on the size of the void and the viscosity of slag.

Aug 21, 2024

By J Palarski

Over the last 100 years in the Polish mining industry considerable work has been done to assess optimum slurry, develop flexible delivery systems and adjust the fill technology to a wide variety of mining and geological conditions. Sand or industrial mineral waste materials for the backfilling of underground voids are used to control ground movement and surface deformation. This paper discusses various criteria to he considered in the preparation of a fill, including slurry properties, mine infrastructure, mining geometry, placement methods and the purpose of the backfill. This paper presents laboratory and in situ test data on the influence of materials parameters on the slurry flow in a pipeline system, stiffness, permeability, binding time and strength of a backfill, on the distribution of mixture in underground voids or the penetration between roof fall Materials.

Jan 1, 1998

By E Claridge

There are a number of major infrastructure tunnelling projects currently underway or proposed in New Zealand, including construction of new road and rail facilities and the refurbishment of existing road tunnels. These new projects have triggered a rethink of traditional practices in underground fire and life safety and local regulation.While there is a current surge in activity, tunnels have been a signifi cant part of New Zealand’s transport infrastructure for over a century. Despite this background, the new projects commonly face challenges that are symptoms of a national regulatory environment that has aspects that are inappropriate for underground environments. There are inconsistencies in local regional regulation and an absence of national guidance and standards relating to tunnel design. Historically, New Zealand has looked across the Tasman for guidance. Although recent overseas tunnel designs present learning opportunities, the adoption of international best practice and standards may not necessarily address local expectations or needs.This paper explores a number of specific matters affecting the design of road and rail tunnels in the New Zealand context, namely; the Building Regulations and associated local consenting processes and parties, and the responsibilities and needs of the New Zealand Fire Service.The discussion highlights the importance of a collaborative approach involving the designer, asset owner, regulators, emergency services, and other parties, and ensuring up-front clarity in design responsibility and ownership of residual risk.

Mar 8, 2011

By D FitzGerald

A critical component of any new tunnel design in a complex geological setting is the development of an integrated three-dimensional (3D) geology model with a full set of geotechnical properties of the rocks present. A novel means of predicting the geology based upon sparse observations of structural geology at the surface and from drill holes has been developed and used in several major tunnel studies in Europe.An example of this is the Lyons-Turin twin rail tunnel which is still in a development phase. This tunnel has been in planning and development for over 15 years already. An important aspect of this work is to characterise geological uncertainty along various possible tunnel paths as an input into early design optimisations for time, cost and risk avoidance strategies. Once the tunnel works commence and more detailed geological data is collected by daily mapping, progressive refi nement of the geological model is desirable; geological conditions still to be encountered can be more accurately predicted. Faults and their offsets, dykes, geological unconformities, folding, as well as standard sedimentary processes are all correctly modelled in the software. It is important to allow for seamless interchange of geological models at various scales with CAD workflows so that sufficient detail can be readily accessed at the required scale. Also, the proposed tunnel in its correct geometry can become a ‘section’ in its own right. Progressive detailed local geology models in the vicinity of the advancing head are created from the regional scale work by cutting and pasting a starting model, then adding all the extra detail for the required engineering geology work.For all rocks, most standard geotechnical quantities such as sonic velocities, Young’s modulus and Poisson’s ratio are handled. These and any other phenomena from borehole observations can have variograms calculated and stratigraphically constrained estimations made in a least biased geostatistical manner, in advance of the tunnel. RQD, or a prediction of rock fractures, is handled by the faulting and folding modelling facilities. This is probably the more interesting issue to pursue, as the fractal nature from small scale fractures and joints, to large-scale faults, can now be characterised more convincingly.

Mar 8, 2011