Search Documents

By P Hogan, M Wells

Reflectance spectroscopy has become an established technique for mineral exploration and ore characterisation. However, there are few reported cases where the technique has been applied to the Hamersley Province channel iron deposits (CID). The Bonnie Creek CID, located ÿ140 km north of Newman in Western Australia, represents one of a number of CIDs recently discovered in the Hamersley Province. Reflectance spectroscopic analysis using the CSIRO HyLoggerÖ automated scanning system, in conjunction with X-ray diffraction and compositional analysis, was used to characterise and map the ore and gangue mineralogy in CID drill core. Using CSIROÆs spectral mineral characterisation scripts, it was possible to map the downhole distribution of the Fe-oxide abundance, hematite:goethite ratio and the gibbsite and kaolinite abundance. Spectral estimates of kaolinite abundance were found to be closely related to loss on ignition measurements at 650¦C and the spectral kaolinite abundance index provided a reliable estimate of the total weight percentage Al2O3 content. In addition, downhole HyLoggerÖ scanning of diamond drill core reliably mapped the distribution of kaolinite as supported by coincidentally elevated contents of alumina and silica. Furthermore, spectrally-derived estimates of iron oxide abundance were well related to assayed Fe wt per cent contents and use of the spectral iron oxide mineral index mapped the distribution of the goethite:hematite ratio, and demonstrated that material logged as high-grade ore in the Bonnie Creek CID was predominantly goethite-rich.CITATION:Wells, M and Hogan, P, 2013. Bonnie Creek channel iron deposits ore mineralogy - insights using the HyLoggerÖ technology, in Proceedings Iron Ore 2013 , pp 321-328 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By N Van Buc, E Coroiu

The rapid socio-economic growth of Hanoi City coincides with a corresponding growth of the transport demand. Today, the transport in Hanoi is completely dependent on private modes of transport. Because of the lack of an efficient public transport system and the expected rapid increase in traffic volumes, the movement of people and goods in the urban areas of Hanoi will cause congestion in the present city transport network. The solution of the construction of new roads, or the widening of the existing streets, is very expensive in urban areas and usually causes many social problems due to the resettlement of people. From the point of view of the number of inhabitants, Hanoi City is now over one million. Above this number the international experience shows that the public transportation must be a mass transport system with large capacity, commercial speed and also independent as much as possible from the street network. According to the Hanoi Master Plan for 2020, the Hanoi urban population will be over 3.5 million persons. Also, in the next 15 years, the distances between centre-destination points will be doubled by comparison to 1995.

Jan 1, 1999

By S Döpp

Commencing with early experiences in iron ore beneficiation made at Beeshoek Mine, the paper follows through the process of extensive mineralogical and metallurgical investigations carried out during feasibility study. The paper will discuss the design process and logic followed over the last years, the challenges and decisions the design team faced in order to draw the conclusions that ultimately resulted in today’s value add approach at Assmang’s Khumani Operations.As integral part of the benefi ciation concept, a focus is set on the jigs, explaining the plant concepts, planned expansions and their contribution to the overall value add approach at the mine.The case study is intended to describe the outcomes of the design versus the actual achieved and the further value add projects to be implemented. As for future prospect, the incorporation of Wet High Intensity Magnetic Separation (WHIMS) demonstrates Assmang Khumani’s pursuit to maximise productivity and overall recovery.DMS was evaluated as an alternative to jigging within a comparative test work study, but in conclusion the option had to be excluded due to its inability to achieve the high density cut point required to achieve the sales specifi cations. In contrast, the investigation on producing an additional middlings fraction on the lumpy ore jigs prove to be an adequate option for further improvements of overall mass yield. With further liberation, a saleable product will be achieved by secondary beneficiation on Fines Jigs and WHIMS.Concluding, jigs are considered the most viable and cost effective benefi ciation process for off-grade ore +0.8 - 32 mm at Beeshoek as well as at Khumani, while WHIMS is the process under consideration for super fines recovery.

Jul 11, 2011

By B M. Patterson, A J. McKinley, M E. Grassi

Large-scale column experiments were undertaken to determine the effect of a step decrease in groundwater pH on metal remediation by bioprecipitation. Metal contaminated groundwater at pH 5.5 was amended with ~1 g/L of ethanol in one column using a polymer mat ethanol delivery system to promote bioprecipitation, while another column was left unamended and used as a control. Sulfate reduction and zinc removal were observed after eight weeks. Zinc removal was observed in the zone of sulfate reduction, indicating precipitation as ZnS, while, copper was removed in the denitrification zone. Once steady state bioprecipitation of zinc had been established, the pH of the metal contaminated influent groundwater was decreased stepwise from 5.5 to 4.25. As a result of the change in pH, a significant increase in copper concentration was observed in both columns. In the ethanol column, the zones of denitrification and copper removal migrated up the column, while both sulfate reduction and zinc removal ceased. Bioprecipitation of metal contaminated groundwater via sulfate reduction was shown to be an effective remediation strategy for zinc removal. However, this in situ biological remediation process was sensitive to changes in groundwater pH.

Jan 1, 2004

By X Ma

Kaolinite is of very fine particle size in nature and thus its dispersion plays a key role in the successful removal of kaolinite in iron ore flotation and selective flocculation processes. As the most widely used dispersant in the world, sodium silicate has been used as a standard dispersant for kaolinite in the iron ore industry. However, the actual effect of sodium silicate on the colloid stability of kaolinite particles and its dispersion mechanism remain unknown in the literature. In this work, the dispersion effect and dispersion mechanisms of some common inorganic and organic dispersants, including sodium silicate, polyphosphate and a low molecular weight polyacrylic acid, on kaolinite particles were systematically investigated through electrophoretic mobility and colloidal stability studies over a wide pH range. It was found that sodium silicate-kaolinite interactions only take place in the neutral and acidic pH range, while polyacrylic acid and polyphosphate interact with kaolinite from pH 3 to 10.5. Consequently, sodium silicate only disperses kaolinite at neutral and acidic pH. In contrast, polyacrylic acid and polyphosphate disperse kaolinite from pH 3 to 10.5, with strong dispersion effect observed at neutral and acidic pH. In the iron ore industry, selective fl occulation and reverse cationic fl otation, the most widely used flotation route, are both conducted at pH 10 to 10.5. The results of the present study show that, at such high pH, polyacrylic acid and polyphosphate are more effective dispersants of kaolinite, in comparison with sodium silicate.

Jul 11, 2011

FOR some years after the erection of the first chlorination plant at Mount Morgan the ore sent to the works for treatment was mined entirely from the oxidized zone; consequently, the bullion recovered at the refinery was of unusual purity, averaging about 972 in fineness, and, as no impurity in any way detrimental to the softness or toughness of the bullion was present, there was no necessity to subject it to any refining process.The charcoal from the filters was calcined to ash in small reverberatory furnaces of the usual type. The ash was mixed with suitable proportions of soda and borax to form a good liquid slag. This' mixture was then charged into salamander cruciblesand run to metal and slag in the ordinary wind furnaces-a slow and tedious proceeding in the Mount Morgan climate. The bullion, cleaned of slag, was re-melted under borax and poured into bars weighing from 350 to 400 oz.; these bars, after being dipped while hot into dilute sulphuric acid, were packed and sent to the mint. Of late years, however, the ore coming from the deeper ground of the oxidized zone became much lower in gold values, and contained variable but increasing quantities of sulphides, sulphates...

Jan 1, 1911

Separating Particles by Horizontal Deflection in a Paramagnetic Fluid This paper describes the horizontal deflection behavior of particles in paramagnetic fluids under a high-gradient superconducting magnetic field. Movements of single particle were observed experimentally and indicated that they could be deflected to different positions. Based on these results, the behavior of groups of particles from ore samples was examined in the superconducting magnetic. It was found that these particles could be deflected and settled at a certain position due to the combination of gravity and magneto-Archimedes forces as well as a lateral buoyancy (displacement) force. Mineral particles with different susceptibilities and/or densities could be deflected to different positions, thus producing groupings of similar types of particles. The work described here, although in its infancy, could form the basis of new approach to separating particles based on a combination of susceptibility and density.  

Sep 13, 2010

By K Biegaj

During the author’s 25+ year career in mine management in various parts of the world (mostly in Australia), the author has been privileged to live and work in mining towns (not FIFO) for more than 20 years. And has personally observed other people from the mining industry carrying out work at home in an unsafe manner, eg pushing lawn mowers whilst wearing thongs or performing electrical jobs whilst standing on aluminium ladders, as well as many others. It is common that injuries sustained at home whilst on break are not reported upon arrival back on a mine site. A large number of compensation claims for injuries at work, which in fact had been sustained at home, come at substantial extra costs to mining companies.

May 5, 2022

Professional engineers of today require a wide array of experience and knowledge. It is true that commonly engineering degrees do teach the technical requirements well, but do fall short in the way of teaching other non-technical issues of professionalism to the student. Today calls for an engineer who does not only have a high standard of the technical knowledge required for their degree, but also has a broad range of experience in areas that are becoming increasingly important in engineering. The importance of social responsibility, liability and interpersonal relations is high. Through the face of the changing world, it has become clear that there is a need for a new type of engineer, who has a broad range of expertise, as well as the typical technical abilities required. This paper will outline these non-technical issues and propose ways of combining these ideas into the mainstream engineering degree.

Jan 1, 2004

With the burgeoning opportunities for new gold mines to be developed the opportunity now exists for a reassessment of the optimal processing path for these gold ores. Projects have traditionally followed the path of whole ore cyanidation with either Carbon In Pulp (CIP), Carbon In Leach (CIL) or Merrill Crowe. The challenge ahead is whether these traditional processing methods are the best option for stakeholders, or to go beyond CIP and use a combination of currently available technologies that can be used to provide gold recovery at a significantly reduced capital cost and minimal deleterious impact on the environment. Either stand alone or combinations of gravity concentration and flotation, can produce a gold bearing concentrate that can then be fed directly to a batch or continuous intensive cyanidation unit. Treatment of a gravity/flotation concentrate by intensive cyanidation may be processed by the InLine Leach Reactor (ILR) developed by Gekko Systems of Australia. The advantages of the technology combining gravity/flotation followed by intensive cyanidation are significantly reduced capital costs; improved safety due to reduced cyanide inventories; the majority of tailings un-contaminated by cyanide; less energy required due to an opportunity for an increase in grind size û reducing green house gas emissions; detoxification of concentrate tailings can minimise tailings disposal and containment requirements.

Jan 1, 2004

By Y Cui, G Cao, H Zong, J Zheng, J Wang, S Yue, J Zhao, B Li

The iron (Fe) concentration in nickel slag is high, making its recovery and utilisation a hot and challenging topic. In the nickel smelting process, using CaO instead of SiO2 to adjust slag’s composition, and then directly reducing Fe from the output of molten slag is a more feasible method in practice for Fe recovery in nickel slag. The adjustment of slag’s composition in the nickel smelting process will have an impact on the distribution of impurity elements such as Pb, Zn, and As. In this paper, the slag adjustment of nickel smelting process was carried out with the oxygen-enriched topblowing system. The distribution of impurity elements in the smelting products with each composition slag was conducted by using thermodynamic software. Experimental verification was performed with rich oxygen top-blowing, and the distribution characteristics of impurity elements in the smelting products were characterised to explore the differences in mineral phases of impurity elements with each smelting conditions, elucidating the distribution patterns of Pb, Zn, and As in each phase. The results indicate that after slag adjustment, impurity elements are more easily to volatilisation and removal into the gas, reducing their total concentration in slag and matte. In the slag, the existence form of Pb, Zn is changed from silicate to ferrate, and As is changed from arsenate to low-valent arsenic oxide. It is easier to decompose the impurity-containing mineral phase and remove the impurity elements in the subsequent iron extraction process.

Jun 19, 2024

By G Brooks

The control of phosphorus in steelmaking is one of the famous challenges of pyrometallurgy. It is well established that highly basic slags, the presence of FeO in the slag and lower temperatures (less than 1650°C) are favourable for phosphorous removal. The thermodynamics of this reaction have been extensively studied under laboratory conditions and the general trends confirmed through industrial trials. However, in general, phosphorus slag/metal distributions measured in industry are far from equilibrium and quite specific to the oxygen steelmaking technology being used. This variability was quantified by Urban, Weinberg and Cappel (2015), who found that the phosphorus partition ratio measured in plants varied with blowing practice, stirring intensity and even converter life. Some recent kinetic studies by Gu, Dogan and Coley (2017) have shown how the kinetics of these reactions vary with FeO content and dissolved sulfur at the droplet scale. A global kinetic model by Rout et al (2018) provides meaningful predictions of where dephosphorisation occurs in an industrial basic oxygen furnace (BOF) and some recent heat transfer modelling by Madhavan et al (2021, 2022) implies that temperature difference between droplets and slag has a role to play in explaining why equilibrium is not achieved. This paper will review the current state of knowledge and provide suggestions on predicting phosphorous removal for industrial operations and how greater removal could be achieved.

Jun 19, 2024

By A G. Sheard

Fire safety requirements inside tunnels have become more demanding as tunnel designers consider the impact of potentially larger fires. Tunnel ventilation equipment is required to clear hot gases in the event of a fire. This is vital to maintain smoke free escape routes for people trapped in the tunnel and to facilitate safe access for emergency services. As the fire becomes larger, the temperature of clearing hot gases increases. Traditionally, engineers have taken into consideration gas temperatures of 250°C when designing tunnels. Because of larger fires, engineers must now design equipment to clear hot gas up to 400°C.Increasing the temperature of hot gases to 400°C requires tunnel ventilation equipment that goes beyond historic limits. As temperature rises, material strength reduces, consequently mechanically constraining fan aerodynamic performance. Developing tunnel ventilation equipment suitable for clearing hot gases at 400°C requires a fan technology that is more typical of industrial turbomachinery. The standards EN 12101-3:2002 and ISO 21927-3:2006 defi ne the necessary design criteria and testing methodologies to verify that a range of tunnel ventilation equipment is capable of extracting hot gases.This paper describes the process by which the authors certified in accordance with EN 12101-3 and International Organization for Standardization (ISO) 21927-3 a range of powered ventilators suitable for clearing smoke and hot gases at 400°C for two hours. Proving the high temperature capability of the new range provided a challenge as a consequence of the large physical sizes and high motor powers involved. Additionally, the need to install vertically, as well as horizontally, imposed high thrust loads on motor bearings, further complicating both mechanical design and testing. The paper presents the methods by which the authors overcame these challenges.

Mar 8, 2011

Early in 1950 a new laboratory was set up to deal with problems in mineragraphy, petrology and metallography. This paper describes the equipment, the organisation and association of the laboratory with the various departments of the company, the work that has been done and future plans.At Mount Isa it was soon realised that the microscope would play a most important role in mineral dressing problems and aiding geological research.As early as 1928, R. J. Colony submitted a petrographic report on Black Star ore for Consolidated Limited; much later, in 1934-5 Dr. Grondijs published for Mount Isa Mines Limited a preliminary study of the Mount Isa orebody, followed by a mineragraphicinvestigation of mill products, and in 1937 a Study of Mount Isa Ores by H. GrondIjs and C. Schouten appeared in Economic Geology, for June-July. Other papers dealing with the petrology and mineragraphy of Mount Isa ores are appended at the end of the paper.The mill research metallurgical staff has endeavoured to incorporate mineragraphy in solving milling problems and determining the effectiveness of laboratory as well as examining minerals sent in by the geological department.For many years the amount of equipment available was limited and much of it was locally made or improvised. An improvised briquetting machine, and grinding and polishing lap gave moderate results in conjunction with an old, but serviceable, Leitz microscope. However, for more detailed and accurate work not possible with improvised equipment, many mineragraphic problems were sent to specialist in.

Jan 1, 1953

In practice a sampling solution is a compromise of many requirements: the sample should be representative; the sampling system should also be reliable, less than 95 per cent availability restricts the use of the assayed sample for process control purposes; no sample is the worst sample, and investment costs and installation space/layout are frequently a restriction. For instance, online X-ray analysers for process control introduce a delimitation error by the nature of X-ray physics. Thus only in special cases a relative accuracy better than three per cent relative, as one standard deviation, is achieved. A sampling system for process control needs not to be, as representative, for so many sample properties, as one for composite laboratory analysis samples. Sampling system maintenance is also an important issue. There are many sampling systems in the industry which have been difficult to maintain and are in disuse for lack of resources or incentives to keep them running. Pierre Gy developed the most generally accepted sampling theory. One of the main principles is that all particles in a one-dimensional process stream should have equal chances of being included into the sample. A correctly designed and operated transversing cutter comes close to this goal but has limitations in temporal representativity. For slurries an acceptable solution in many cases is to use a fixed vertical cutter(s) in a position where the slurry is well-mixed by turbulence and other means. For online analysis, reliability problems are mostly related to faulty design or installation of the piping system to the analyser. Properties of material processed, process flow sheet and piping details before and after the sampler have to be taken into account when deciding on which sampling arrangement is appropriate. Guidelines and some solutions to these issues are presented in this paper.

Mar 1, 2010

By K Knorr, S Birch

The mineralogy of new certified-reference-materials (CRM) for X-ray fluorescence from Western Australia (ASCRM 030 to 035) was analysed by X-ray diffraction using the BRUKER energy dispersive one-dimensional detector LYNXEYE-XE. The samples were studied using standard-less quantitative phase analysis, based on the Rietveld method. This method delivers the relative amount of crystalline phases. All materials were found to be high-grade iron ore predominantly consisting of hematite and goethite and very low amounts of magnetite. In addition, the gangue mineralogy was characterised. It consists of low-per cent amounts of carbonate (siderite/calcite), quartz, kaolinite, chlorite and gibbsite.Furthermore, all samples were analysed with the external standard method. This is an elegant way to probe for amorphous content without adding an internal standard. All six samples were found to contain up to 16 per cent amorphous or nano-crystalline material.CITATION:Knorr, K and Birch, S, 2013. Mineralogy of new Australian x-ray fluorescence standards, in Proceedings Iron Ore 2013 , pp 269-274 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By Toussaint LF

A brief history of the mineral sands industry is given from a radiation protection standpoint, with gamma radiation and inhalation of radioactive dust being identified as the main sources of radiation exposure of persons working in the plants. The principal sources of gamma radiation exposure are identified and the history of early bagging methods is discussed. The concept of ALARA is introduced and the impact of the "bulka bags" (and more effective monazite storage facilities) are detailed as illustrative examples of dose minimization, together with the requirements for the transport of monazite. The dose from radiation received from inhaled dust is dependent on a number of parameters of the dust, some of which are not well known. ICRP 30 (1978) makes recommendations relating to the intake of radionuclides by workers. These recommendations are discussed with respect to the inhalation of dust containing thorium. The possible pathways of radioactive material throughout the body are also described. The effect of having parameters that differ from ICRP 30 is discussed and suggestions are made relating to measurements that can be carried out to more accurately determine these parameters. Since in some instances the exposures to dust yield personal doses which may exceed the annual ICRP 30 based limits, it is necessary to define more accurately parameters of the dust so as to determine more accurately personal Doses.

Jan 1, 1986

By G Lane, S La Brooy

A century ago, new mines were often accompanied by smelters. In Australia, smelters were built at the Daydream mine near Broken Hill, at Kuridala and Mount Elliott near Mount Isa, Broken Hill, Mount Lyell, Mount Morgan, Mount Isa, and more recently at Tennant Creek, Kalgoorlie and Olympic Dam. Now the big miners eschew site-based processing in favour of shipping concentrate to smelters in Europe and Asia. As Chip Goodyear was in the process of vacating his leadership role at BHP Billiton, he was quoted as saying that BHP should concentrate on mining ore and leave æto others the skill set of processing that materialÆ. Yet there are times when on-site processing clearly makes sense. Few companies ship gold ore or concentrate to China for gold extraction. New smelters are being built in Zambia. Solvent-extraction and electrowinning plants frequently produce copper from oxide ores and concentrates while pressure leaching is increasingly being considered for copper sulfide ores. Some argue that on-site processing is best because the waste products can be returned to the ground from whence they came, avoiding potentially large disposal costs in more-populated areas. Copper treatment and refining charges will not remain at $45 per tonne and 4.5 cents per pound forever. This paper examines when it makes sense to use on-site pyro- or hydrometallurgical processes in todayÆs environment and comments on how current trends might alter the balance in future.

Jan 1, 2008

Hydraulic backfill is generally retained in slopes using permeable barricades. Mitchell et a! (1975), Mitchell (1992) and Grice (1989) have shown that under normal drainage conditions, barricades experience low levels of loading. Cowling et a! (1988) have also shown that barricades are susceptible to piping failures if excess water has ponded on the upper backfill surface and if leakage of backfill from the barricades has occurred. During 1997, six hydraulic backfill barricades failed in four different Australian mines. Fortunately, in each case, the quantity of backfill slurry released was small, and no injuries to personnel nor damage occurred. Detailed investigation of two of the incidents showed that the primary cause of failure could be attributed to the delivery of excess quantities of transport water from the low-density slurry. For each of the incidents investigated there was evidence of the development of piping failures, which resulted in hydrostatic loading conditions on the barricades from the ponded water on the upper backfill surface. The circular failure surfaces in the barricades were characteristic of the application of point loading Conditions.

Jan 1, 1998

By L D. Redden, M G. Nelson

Mechanical flotation machine design is typically based on hydrodynamic analysis, with scale-up calculated by geometric proportionality. End users often specify and purchase machines on the basis of retention time, characterised by the æ$/m3Æ approach; they may also consider the manufacturerÆs installed base. In some applications, end users also consider specific energy and the impact of energy consumption on operational costs. In other cases, a decision may be based on machine type (forced-air versus self-aspirating) and perceived metallurgical or operational advantages of one machine type over the other. With regard to metallurgical performance efficient bubble-particle contact is very important and is primarily influenced by two factors:the concentration and size distribution of bubbles in the machineÆs contact zone (the volume enclosed by the disperser); and the number of times that slurry is pumped through the contact zone. The second factor is a function of the machineÆs pumping rate and its retention time. Field data show that pumping efficiency is independent of aeration rate. In this paper, a new dimensionless number for the characterisation of flotation efficiency is presented. The contact frequency number (CFN) is defined as the number of times a given volume of slurry passes through a machineÆs active contact region, and is given by: CFN Qp/Qf, where:Qpis the pumping rate through the contact regionQfis the volumetric feed rate to the machine

Jan 1, 2005