Search Documents

By W. C. Ellis

IN an ingot of germanium solidified progressively from the bottom by a method' devised by J. H. Scaff and H. C. Theuerer, examination discloses ex- IH. C. Torrey and C. A. Whitmer, Crystal Rectifiers. p. 364. 1948. New York. McGraw-Hill Pub. Co. tensive twin relationships. A slice taken about midway in a cylindrical ingot approximately 3/4 in. in diameter and 1 1/2 in. in length, after etching and polishing to delineate different orientations, is shown in fig. la. The orientations of the regions designated with letters were determined by Laue X-ray back-reflection methods and plotted on stereograms. The orientation relationships of the designated components were determined by comparing the values for the nine angles between the three respective cube poles of each orientation with the values calculated in a formal treatment of octahedral multiple twinning in cubic crystals. Germanium, diamond cubic in structure, has the octahedral twinning habit. I am indebted to K. H. Storks for the calculation of the angular relationships of cube poles in octahedral twinning to four orders. The set of values for the nine angles is distinctive of the order of twinning. Confirmation for a multiple twin relationship is obtained from the determined indices of the mirror planes. These exist for all orders of twinning through the third and for some of the fourth." If the orientations are not those for twinning, then the nine angles for the cube poles do not correspond in value and distribution to those formally calculated. Since all nine angles must correspond in values and distribution of values to the calculated ones, the Laue method with a precision of one or two degrees is adequate to establish or deny with confidence the existence of multiple twins. Regions of the same orientation can also frequently be identified by the optical reflections. For example, the narrow twin bands in A at 2: 00 o'clock have orientation B1. The interesting twin relationships shown schematically in fig. lb were found for the section in fig. la. Most of this slice was made up of orientation, A, appearing in widely separated regions. Of the four possible first order twins of A, three were present in this slice and are designated by B with subscripts. Four second order twins of A are designated by C with subscripts. It is worth emphasizing that two of these, C, and C,, are second orders of A through the first order missing in this section. Two regions, designated by D with subscripts are third order twins of A. D2 is a sixth order twin of D,. All orientations found were ascribable to multiple twinning, as if the orientations in this section originated earlier in solidification from a single nucleus. The presence of extensive multiple twinning to- gether with the absence of other orientations appears to be a characteristic result in many instances of solidification of germanium. Fertile conditions for twinning probably exist in the array of atoms in the diamond cubic structure. The high order twins in the section shown, it is reasonable to presume, are the result of progressive octahedral twinning through several generations in the material freezing earlier. Some of these generations do not appear in this section, it is suggested, because their orientations with respect to the growth direction were unfavorable for survival. The extensive twinning is probably promoted during solidification by constraint imposed by volume increase, and to an irregular growth front. Twinning may also be due, in part, to the attempt of the solidifying region to attain the orientation most favorable to the growth direction (maximum thermal gradient). The nucleus for a twinned orientation could have its origin in a "stacking fault" on the close-packed octahedral plane. Further work is being done in which the course of twinning throughout an ingot is being studied. The results appear to be important in the general theory of solidification.

Jan 1, 1951

By Leonard L. Melton, Calvin D. Saunders

The design and performance of many operations common to the petroleum industry depend upon the unique properties of a class of materials known as non-Newtonian fluids. The art of measuring and describing these properties, called rheology, has fallen far behind the field applica-tion of these fluids in this industry. Empirical methods are still employed although theoretically sound methods of analysis are now available. This paper illustrates a completely general method of analysis of the rheological properties of non-Newtonian fluids which id independent of the type of viscometer employed and also the rheological type of fluid encountered except those of a thixo-tropic or rheopectic nature. Values of the rheological properties of a fluid obtained using this method of analysis are based upon an absolute scale of measurement, eliminating the necessity of employ-jng arbitrary concepts of the flow properties of non-Newtonian fluids, The fundamental nature of this method of analysis is further demonstrated by evaluating the precision with which measurements have been made of these rheological properties by employing a dimensionless criteric: —the Fanning friction factor-Reynolds number correlation. INTRODUCTION Non-Newtonian fluids are not new in the petroleum industry. Particular properties of non-Newtonian materials have been recognized and used to advantage in drilling fluids and have found excellent application in the hydraulic fracturing process.'.' While usage of these fluids is not new in this industry, the art of measuring and describing their rheological properties is still in its infancy. This is reflected in the accepted method of evaluating drilling fluids, API RP 29, (1950), which recommends a one point "viscosity" measurement. These shortcomings are recognized by various groups in the industry and more adequate methods have been prposed.3,4 The efforts Of these people are to be commended; but, at the same time, the limitations of their method of analysis and viscometer must be appreciated. This method Of analysis is applicable Only to Bingham plastic fluids as is pointed out early in their articles. The consistency of a Bingham plastic fluid must also lie within the range of the viscometer which is also well defined by the author. It is believed that the apparent simplicity of this method of analysis and the utility Of Operation Of their viscometer will soon make the terms non-Newtonian fluid and Bingham plastic fluid synonymous as used in this industry; a tendency which has already been encountered. Application of this method of analysis to a non-Newtonian fluid other than a Bingham plastic can lead to erroneous results. The field of rheology has long been hampered by the adherence to arbitrary concepts of Of of the flow properties Of non-Newtonian fluids. This has resulted in the design and operation of viscometers so as to fulfill these concepts rather than following the more logical method of analyzing experimental data so as to yield a fundamental truth. completely Bingham proposed the concept Of plastic flow and yield asu rement. data presented by Buckingham could hardly be interpreted so as to substantiate this theory; but rather succeeded in establishing the fact that compliance with this flow concept could never be realized in the capillary tube vis-cometer.5 Bingham, in reply, sug-gested "Rather than complicate our formula, it would seem to me a much better plan to so change the conditions of flow that the formula will be linear... Reiner0 stated .This plan has been followed by me in collaboration with Miss Riwlin. . . . From the present paper (Reiner and Riwlin, 1929) it will be seen that it is possible to choose the conditions of flow so that the formula based on Bingham's law of plastic flow remains linear. This is realized in the rotation viscometer," Thus, a viscometer, with design and operation based on the Reiner and Riwlin equation for plastic flow, is restricted to a specific range of flow

Jan 1, 1958

By Orville R. Lyons

THE relative performance of coal washing equipment, or the effectiveness with which any type or make of equipment removes impurities from coal, has been most difficult to evaluate in the past. The most widely used yardstick is the Frazer and Yancey efficiency formula developed in 1922,1 but Yancey in a later article states that "washers treating coals of different density composition or operating at different densities of separation cannot be compared directly on the basis of this criterion."' Prior to and since 1922, a variety of other methods has been used for comparison purposes, including the distribution curve, the error area, and the "ecart probable" or probable error. Yancey and Geer in discussing these methods conclude, "Performance can be evaluated in a number of different ways, with the choice of the proper method to use being dictated by the objectives of the investigation and the data available."' It is true that performance can be evaluated in a variety of ways, but if the equipment is to be evaluated on an effectiveness basis, there should be only one universal comparison method. Varying methods have been used because one universal comparison method has not been found or developed. In the article previously quoted, Yancey and Geer state in clear terms the primary concept for a universal comparison method: "One of the simplest, and certainly one of the most obvious evaluations of washery performance is the quantity of sink material in the washed coal and the float material in the refuse. If the washery products are tested at the density at which the washing unit is operated, the sink in the washed coal and the float in the refuse represent material that has been misplaced." The quantity of misplaced material was used as a criterion of washery performance by Lincoln in 1913,8 by the United States Bureau of Mines in 1938,4 by Hancock in 1947,3 and by the national French research agency Cerchar in recent years.2 In 1950 Anderson' proposed the use of this criterion as an efficiency value to replace the Frazer and Yancey formula. However, none of the above-mentioned investigators used the misplaced material concept in a manner that would provide universal coal-cleaning equipment comparisons. The Correlation Theory The ideal coal cleaning process would treat all sizes and would make a perfect separation at any given specific gravity. All material lower in density than the desired value would report in the coal product and all material higher in density would report in the refuse product. Unfortunately, no known cleaning process achieves this goal and there seems little likelihood that any process yet to be invented will do more than approach it. When coal is treated in volume under operating conditions, it is impossible to avoid mechanical entrapment, fluctuations in throughput and effective gravity of separation, and the creation of turbulent currents, even when a true heavy-liquid bath is used and the feed is closely sized and contains little intermediate gravity material. This being so, it is possible to appreciate the difficulties inherent in trying to obtain a perfect separation when treating a wide range of sizes and a feed containing high percentages of intermediate material, using turbulent currents to help create the effective separation gravity, under operating conditions which normally tend to be on the overload side. When coal is separated from refuse in any coal cleaning equipment, some refuse always reports to the coal and some coal to the refuse; the writer therefore assumed that there should be a relationship between the total amount of misplaced material produced by any given piece of equipment and the difficulty of separation as represented by the percentage of near gravity material in the feed. With small amounts of near gravity or ±0.1 material in the feed there should be less misplacement of material than would occur with large amounts of near

Jan 1, 1952

By W. R. Kube, W. H. Oppelt

Five low-rank coals, including two lignites, a steam-dried lignite, and two subbituminous coals, were carbonized at 940°F, in a bench-scale carbon-ize~ with a nitrogen and hydrogen atmosphere, or both, using pressures from atmospheric to 1000 psig. Coking characteristics were observed, and yields, composition, and distribution of products from thermal degradation were determined. The influence of pressure on yields from coal carbonization, as well as on modification of coke structure, has long been of interest. One of the first attempts at pressure carbonization was that of Capps and Hulett1 who in 1917 investigated the effects of pressure ranging from 1 to 20 atm on yields at 600° C for bituminous and subbituminous coals. High-pressure carbonization has not been used commercially for coke production. More recently, carbonization at relatively high pressure in the presence of catalysts and hydrogen has been proposed for the production of metallurgical-grade coke from low-rank fuels.' Another approach involves carbonization at high pressure in a hydrogen atmosphere to produce heating gas and a solid residue that is gasified with oxygen and steam to produce the hydrogen required for hydro-genation 3-4 or, alternatively, is burned to raise steam. Recently it has been proposed to carbonize coal under pressure, burn the gas in a gas turbine to produce power, and use the solid residue as fuel in a conventional steam-power plant.5 Our primary interest in pressure carbonization stems from an attempt to determine the influence of pressure on the coking characteristics of lignite to design a high-pressure slagging gasifier using oxygen and steam. At atmospheric pressure, North Dakota lignite is generally considered to be non-coking. However, lignite and subbituminous coals have been reported to show increased agglomeration properties in steam, hydrogen, or carbon-dioxide atmospheres at elevated pressures, although no strong coke was formed at pressures up to 3000 psig.6 If lignite would agglomerate seriously under gasification conditions, proper flow of charge through the gasifier could not be maintained without installing a mechanical stirring device or destroying the caking properties of the coal before gasification. Data on the caking properties of lignite or other gasification fuel, as well as on yields of products under conditions simulating the carbonization process in the pregasification zone, were required in the preliminary design stage of the gasifier. No information was available concerning the influence of pressure and type of atmosphere on North Dakota lignite. To provide this basic data, the U. S. Bureau of Mines investigated the effect of pressure and a hydrogen or nitrogen-rich atmosphere on the yield of products and on coke formation in a bench-scale pressure carbon-izer. SCOPE OF INVESTIGATION Five coals were tested at 940°F in nitrogen and hydrogen atmospheres, at pressures from atmospheric to 1000 psig. Yields and composition of solid, liquid, and gaseous products were determined as a function of the process pressure, and attention was given to the physical appearance of the solid residue. Percentage of carbon converted, sulfur retained in char, and thermal balances were calculated. In this paper, primary consideration is given to carbonization in a nitrogen atmosphere and to data concerning the solid phase. The effect of pressure in hydrogen is presented in detail for only one lignite. More complete information on the response of the other coals in a hydrogen atmosphere will be published in a USBM Report of Investigations. DESCRIPTION OF EQUIPMENT Details of the bench-scale pressure carbonizer are given in Fig. 1. The body of the carbonizer was

Jan 1, 1961

By S. J. Burns, W. W. Webb

The dislocation arrangements formed during unsteady propagation of cleavage fractures on (010) planes in LiF have been investigated by high-resolution etch-pit techniques and by X-ray diffraction topogvaphy. In impurity-hardened crystals, cracks propagating in any direction on (010) planes at velocities of about 103 cm per sec are usually accompanied by light plastic deformation which is enhanced wherever the crack is allowed to hesitate. Dislocations with [011] type Burger's vectors are often formed looped around the crack tip. They are dragged along with the crack tips leaving edge dislocations lying nearly parallel with the clearage surface about 5µ from it. These dislocations are easily overlooked since they may initially intersect with the cleavage surface infrequently and later may disappear from the crystals due to image forces during aging at room temperature. Although the plastic work associated with these dislocations is only comparable with the reversible (010) surface energy, an instability in crack propagation appears due to a limit of the velocity with which dislocations can be dragged along with the crack. Transition to a fully brittle nonplastic fracture mode occurs when the crack velocity exceeds the velocity with which dislocations can be moved by the stress field of the crack. TRANSITIONS between brittle and ductile modes of fracture appear to be common processes in the behavior of materials in which the flow stress is close to the stress at which brittle cracks can propagate. High-strength engineering alloys fit into this category and the transition from ductile to brittle modes of crack propagation may be associated with catastrophic failures in these important materials. The methods of theoretical mechanics indicate the geometrical conditions in which these processes may occur but the detailed mechanisms controlling the generation of dislocations in the initiation of the plastic mode and the process by which the loss of plasticity occurs on transition to the brittle mode are not yet clear. Since these mechanisms are not amenable to direct observation in engineering alloys we have chosen a semi-ductile alkali halide LiF as a model system in which to observe transition mechanisms between plastic and brittle modes of crack propagation. Cleavage cracks in this system are known to undergo a plastic-elastic transition at velocities between 103 to 104 cm per secl and dislocation configurations in LiF are amenable to study by optical-microscopic observation of dislocation etch pits2 and by X-ray diffraction topography.3 We have been able to identify a dislocation mechanism responsible for the transition from brittle to slightly plastic modes of crack propagation in LiF. A model based on this mechanism permits calculation of the critical crack-propagation velocity for this transition and indicates the importance of the stress dependence of dislocation velocity in determining the critical crack velocity. Of course, this model cannot be carried directly over to more complex materials but it is quite possible that its qualitative features are generally applicable. Dislocations intersecting fresh cleavage surfaces in LiF were reported by Gilman,4 by Forty,5 and by Wash-burn et a1.6 Such dislocations were construed to have been nucleated where the cleavage crack hesitated or stopped, near stress concentrators, such as cleavage steps, on the crystal face. The loci of such dislocations deposited On the cleavage plane in bands were called "stop lines" or "deformation zones". Gilman, Knudsen, and walshl measured the velocity of cleavage cracks in lithium fluoride by evaporating thin resistive strips on the crystal side and recording

Jan 1, 1967

By B. A. Eaton, R. H. Jacoby

This paper presents the depletion-performance correlations developed using data from PVT studies and well-completion tests of 27 rich gas-condensate and volatile-oil reservoir fluids. The PVT behavior for each fluid war determined experimentally in the laboratory, and the depletion performance of each fluid was then calculated. Well-completion test data consisting of reservoir pressure and temperature, initial total gas-oil ratio, and stock-tank oil gravity were used with the depletion-performance data to develop general performance correlations. Three correlations are presented. The first equation shows the empirical relation of gas in place per barrel of hydrocarbon pore space with reservoir pressure and temperature, and initial total gas-oil ratio. The second equation is the correlation of stock-tank oil in place per barrel of hydrocarbon pore space. The third equation relates stock-tank oil production (to 500-psia depletion pressure) with pressure, temperature and oil gravity. All three correlations are also presented in convenient graphical form. Gas production to 500-psia depletion pressure is approximately 92.6 per cent of the gas in place for each fluid, so no correlation was developed for gas production. INTRODUCTION The rate of discovery of shallow, low-pressure and low-temperature oil reservoirs in the United States has been declining in recent years. For this reason, the search for oil has gone to greater depths where high pressures and temperatures are encountered. A high-pressure and high-temperature reservoir is the environment in which many rich gas condensates and highly volatile oils are found. Because of this trend, the performance prediction of such reservoirs has become an important task of the reservoir engineer. The need and usefulness of a performance correlation based on field data that are available from the usual well-completion tests have previously been established. These earlier attempts have shown that the phase behavior of rich gas-condensate systems and volatile-oil systems can be correlated with fluid properties, pressure and temperature. However, very little information on gas-condensate depletion performance5 was available at the time of these earlier attempts. The availability of more recent data has made possible the development of an improved correlation. The data, as listed in Tables I and 2, are for 25 gas-condensate and two volatile-oil systems that were studied. The problem was to correlate the data for in-place fluids and the production data with the initial total gas-oil ratio, initial reservoir pressure and temperature, and stock-tank oil gravity. These correlations were obtained by multiple regression analysis, whereby the data were fitted to an equation by the method of least squared error. BASIS OF THE CORRELATIONS 1. The data used in the development of these correlations were obtained from depletion-performance calculations6 and well-test or production measurements. 2. All of the independent variables used in the correlations are available from the usual well-test completion data. 3. The reservoir volume considered is 1 bbl of hydrocarbon pore space (HCPS). 4. The gas-oil ratio used is the total standard cubic feet of gas (at 14.7 psia, 60F) coming off the entire separator train per barrel of stock-tank oil. This minimizes the effect of separator conditions which might vary from system to system. 5. The correlated pressures are the actual reservoir pressures which might or might not be the saturation pressure of the reservoir fluid.

Jan 1, 1966

By H. M. Davis, T. S. Jones

A methodfor accelerating the reduction of a metal oxide by carbon monoxide is to incorporate in the reduction system a nonreducible oxide which has a strong affinity for carbon dioxide and will remove it from the product gases. The effectiveness of this method was investigated by veduction experiments on specially prepared powder mixtures of SrO-ZnO ("active'.) and SrCO3-ZnO (reference). Measurements at 750o and 677°C showed that the rate of reduction of ZnO by CO was as much as an order of magnitude greater in the presence of SrO. Under the experimental conditions at least as much CO2 as generated by veduction was absorbed when SrO was present. Enlzancernent of the veduction rate by SvO resulted from modification of' gaseous djfitsion processes. THE specific question posed in this investigation was whether the reduction reaction CO + ZnO - Zn(g) + COa [1] could be accelerated by incorporating strontium oxide into the oxide charge undergoing reduction. Provided the strontium oxide was active enough, it could remove carbon dioxide from the product gases of ( 11 and form strontium carbonate, thus modifying Reaction [ 1] to CO + ZnO + SrO = Zn(g) + SrCO3 [ 2] This study of the comparative rates of Reactions [ I] and [2] can be considered as a particular case of a general scheme for increasing the rates of reduction of metal oxides by carbon monoxide. The limits of applicability of this scheme are indicated in the simple thermodynamic analysis presented in the appendix. This analysis primarily dictated the choice of the system, CO-ZnO-SrO, employed in this investigation. In addition, it was thought that a study of this scheme by use of the CO-ZnO-SrO reaction system would be of special interest in view of indications in the literature1-3 that the gaseous reduction of zinc oxide is prone to rate control by diffusion in the gas phase. The distinction should be pointed out between this and other efforts to increase the rates of reduction reactions through the use of addition agents. Additions of a wide range of chemicals have been tried with de- grees of apparent success varying from slightly negative to highly positive. The reasons for making additions have included the use of salts to produce effects akin to catalysis,4, 5 the alteration of the microstruc-tural details of the reduction process (including solid-state diffusion),6-8 and the conversion of an en-dothermic reaction into one that is exothermic or autogenous.9-12 The means used to attempt alteration of the enthalpy change has commonly been to incorporate lime into the charge, so that heat is generated by reaction with either of the reaction products, carbon dioxide or water. The use of lime in this way makes endeavors such as that of Edstrom and Wiberg similar to the present one. Furthermore, the basic principle behind the present work has previously been set forth.13 However, a detailed investigation of the type of reaction described in this work does not appear to have been conducted. EXPERIMENTAL PROCEDURE From both conceptual and physical standpoints, Reaction [2] is to be considered as the sum of two reactions:

Jan 1, 1968

By C. H. Lee, R. Maddin

The diffusion rates of Ag110 in cylindrical single crystals of 99.99 pct pure silver, which were twisted to a total surface strain of 0.91 during the diffusion anneal at temperatures of 700°, 750°, and 800°C, were measured by sectioning and counting as a function of the strain rates. The ratio of the diffusivities while strain ing occurred (Ds) to those of the unstrained specimens varies linearly with the rate of twisting and attains values of near 100 for some of the rates used. The enhancement of diffusion by straining is inversely proportional to the temperature at which diffusion occurs. The activation energy for diffusion determined from the data plotted as a function of the rate of twisting decreases from 44,090 cal per mole for zero strain, to an asymptotic value of 21,000 cal per mole for the strain rates of 22 x it)"5 see-l. Qualitative explanation for the observations based on the generation of nonequilibrium number of defects by plastic deformation will be discussed. The initial research of Buffington and cohen1 on self-diffusion in a iron under compressive stresses contributed the first quantitative information concerning the effect of applied stresses on diffusion. These results were obtained from radioactive Fe55 plated on one of the horizontal surfaces and compressing the large-grained specimens while the diffusion-anneal was occurring. Enhancement of diffusion of a maximum of seventeen times was observed provided the strain was in the tertiary stage of creep and the rates of straining were at least as fast as rates used in the normal creep test. On the other hand, Darby, Tomizuka, and Balluffi,2 extending silver single crystals up to 30 pct elongation at rates of straining about equal to those used by Buffington and Cohen observed no effect. For the past two and a half years at the University of Pennsylvania, we have been investigating the effect or torsional strains on self-diffusion in silver single crystals. If enhancement is observed as has been reported1 a possible explanation may be based upon the generation of fairly large numbers of point defects and their role in the diffusion process. Hence, since torsion should produce an abundance3 of point defects, an increase in the diffusivity while the crystal is being twisted should easily be measured. EXPERIMENTAL PROCEDURE Our research uses single crystals of silver prepared from 99.99 Ag by the Bridgman method in a dynamic vacuum of less than 25 µ. As grown, they are about 25 cm long by 1.3 cm in diam. The crystals are cut into 7.5 cm lengths with a jeweler's saw and machined to the shape shown in Fig. 1. The test length of the crystal is machined to a 0.6 cm diam after which the ends are masked and the test section etched heavily in HNO3, and KCN:(NH4),S2Os , solution to remove the effects of machining. The specimen is then annealed in vacuum for 8 to 12 hr at 800°C to remove any residual stresses and also to recrystallize the end sections. The recrystallized ends are necessary since experiments showed that single-crystalline end sections are too soft to transmit the desired torque. Occasionally, recrystalliza-

Jan 1, 1960

By M. Garfinkle, W. D. Klopp, W. R. Witzke

The tensile properties of binary W-Re alloys containing up to 33 at. pct Re were determined at temperatures from 78" to 3630°F. Elongations as high as 260 pct were observed in electron-beam-melted tungsten containing 23 at. pct Re when tensile-tested at 3630°F after a 1-hr anneal at 3090°F. All alloys tested under these conditions with rhenium contents between 20 and 28 at. pct exhibited elongations of at least 200 pct. These alloys also showed enhanced grain growth rates. The values of strain-rate sensitivity ranged between 0.2 and 0.3 for the alloys exhibiting high elongations. Houlezler, for swaged alloys tested just above the re-crystallization temperature, strain-rate sensitivities as high as 0.8 were observed. The high-temperature strengths of the high-rhenium-content alloys were also less than those of alloys with intermediate rhenium contents. ALLOYING with rhenium has two distinct effects on the mechanical properties of tungsten. One effect occurs in dilute solid solutions and is most clearly seen in the lowering of the hardness and of the ductile-brittle transition temperature at about 5 at. pct Re.1-3 The second effect occurs in the concentrated solid solution at about 25 at. pct Re, and is characterized by twinning and a larger decrease in the ductile-brittle transition temperature. An aspect of the high-rhenium-content alloy which has received little attention is the higher-than-usual tensile ductility at 3500°F.3 Anomalous high ductility has been observed in several other alloy systems. usually associated with a phase transformation or a solid-solubility limit.4'5 The phenomenon is now commonly termed superplasticity. High-strain-rate sensitivities6 and grain boundary sliding7 have been reported for materials that undergo superplastic deformation. Also, it has been found that superplastic materials usually have a very fine grain structure (less than 10 pm).8 and it has been proposedg that such a structure alone is sufficient for superplasticity. The purpose of the present study was to further characterize the high-temperature tensile properties of W-Re alloys to determine the conditions under which they might be superplastic. Tensile and selected strain-rate sensitivity tests were conducted on alloys containing 0 to 33.3 at. pct Re at temperatures from 78" to 3630°F. Grain-growth rates were also determined on most alloys at 3630°F. Fig. 1 indicates the compositions evaluated and their locations relative to the solvus line in the tungsten-rich end of the W-Re phase diagram. Twelve binary W-Re alloys containing up to 33.3 at pct Re were double electron-beam-melted and subsequently fabricated to 0.3-in. rod by extrusion and swaging. The starting materials were commercial powders of tungsten and rhenium with impurity levels as listed in Table I. The various blended W-Re compositions were hydrostatically pressed at 70 ksi. The pressed bars were drip-melted into 1.5-in.-diam ingots and then remelted into 2-in.-diam ingots at a chamber pressure of 10~5 torr. The ingots were canned in molybdenum and extruded to round bar at a reduction ratio of 6:l. The alloy extrusions were swaged to about an 80 pct reduction at 2100" to 2900°F. Buttonhead tensile specimens with a reduced section diameter of 0.16 in. and a gage length of 1.0 in. were centerless-ground from the swaged bars

Jan 1, 1970

By Stephen Zorn

INTRODUCTION The process of financing mining projects in developing countries has changed greatly in the past 15 years. New methods of financing, notably the use of syndicated Eurocurrency project loans, have appeared, and direct equity financing by transnational mining corporations has become less significant. These changes are of particular importance to developing countries which have many mineral deposits still awaiting development, or even discovery. If major new mines are to be financed, host governments will need to obtain more sophisticated information than has hitherto been widely available as to the various sources of finance currently available and as to possibilities for innovative approaches to financing, such as the combination of several different kinds of financing in a single package. This paper reviews the major sources of mining finance potentially available to developing countries and highlights those problems in obtaining adequate financing that developing country producers have begun to experience in the last few years and that are likely to persist through the 1980s. Section I surveys the major types of mining finance; section II reviews specific financing problems, including (a) the withdrawal of the transnational corporations from developing countries, (b) inflation and the size of new projects; (c) developing country indebtedness, and (d) competition among projects in different countries. SOURCES OF DEVELOPING COUNTRY MINING CAPITAL1/ There is a wide range of financing mechanisms which are potentially available to developing countries with economically viable mining projects., Moreover, these financing mechanisms have not been fully exploited by developing countries, and more aggressive pursuit of financing by the governments of these countries may well reveal greater possibilities in respect of any particular project than may initially have appeared. However, virtually all the funds available from these sources are available only to projects which meet the standards of viability acceptable to lenders and others in the business community. If a project does not, for example, promise to generate a discounted cash flow rate of return of at least 15 per cent on total funds employed, or if it does not appear likely to generate sufficient cash flow in the early years of production to cover debt service requirements with a comfortable margin in reserve, most of the sources of financing will not be available. Only where a government has its own financial surplus (as in the case, for example, of the industrialization program of the Saudi Arabian government) can it effectively undertake projects which do not satisfy the definition of economic viability that is accepted at any given time by the worldwide financial community. Internal Sources In Developing Countries Internal financing capacity in developing countries is restricted to a relatively small number of countries - typically those large enough to support a well-rounded industrial sector, in which mining is only one of a number of dynamic industries. While there are large mining companies in certain other countries, the ability of such companies to finance new projects (or even, in some cases, to generate the cash necessary to maintain existing levels of production) is highly problematical. Within developing countries, the possible sources of internally-generated mining finance are the following: (1) state-owned enterprises; (2) private capital; (3) the banking system, and in particular those financing agencies that have a special involvement with the mining sector; and (4) direct budgetary appropriations.

Jan 1, 1985

By M. P. Tixier, M. Gondouin, G. L. Simard

In the quantitative interpretation of the SP logs, the electrochemical component is generally taken equal to — K log Rm /Rw where K has the theoretical value corresponding to solutions of pure sodium chloride. This method may be misleading when relatively large quantities of salts other than NaCl are present in form-rrtion waters—as is generally the case for low salinities —or in gyp-base muds. In such cases recourse is made in the field to changing the K value or to adding a correction term to the equation on the basis of local experience. An investigation has been made in the laboratory of the influence of HCO3, SO4=, Ca++, and Mg++ on the amplitude of the SP deflection, which included in par-ricular determinations of the activity coefficients of Ca++ and Mg++. The theory, the experimental techniques and a tentative method for applying the results are described. So far, applications to actual field cases where chemical analyses of waters were available have provided an excellent confirmation of the proposed method. The case of the SP in very salty brines is also considered and it is shown that the use of activity data for sodium gives satisfactory results. HISTORICAL In early times of electrical logging, the SP curve was used exclusively as a tool for the location of permeable beds and the definition of their boundaries. Later, with the introduction of methods of quantitative analysis, attention was called to the possibility of deriving from the SP log some information on the formation water resistivity, which constitutes one essential element for the computation of water saturation from log data. The first laboratory experiments' in 1932 had shown that, as a result of electrochemical phenomena arising at the contact of the niud and the formation, the amplitude of the deflection of the SP curve was, at least partly, a function of the salt concentration of interstitial water and accordingly of its resistivity. It was indicated that the amplitude of the electrochemical component of the SP should be equal to K log R1/R2, R1 and R2 being the resistivities of the mud and of the formation water respectively. However, the exact value of the K coefficient was not determined at that time because the surface clay used for a laboratory model was far from an ideal shale membrane. Consequently, the way was not yet open towards quantitative interpretation. In the early forties, Tixier reported2, on the basis of field log observations, the following equation for the case of NaCl solutions, SP = -71 log f1c1/f2c2, c1 and c2 being the concentrations and f1, f2 the mean activity coefficients. The local variations observed in the empirical values of K, chiefly in the Rocky Mountains, led him to advance the opinion that, besides the relative amounts, the nature of the salts present in the solutions had a bearing on the magnitude of the SP. At about the same time Mounce and Rust- ad published laboratory results which emphasized the part played by the shale in the generation of the SP. On the basis of laboratory tests and theoretical considerations, Wyllie in 1948' published the following equation of the electrochemical SP for the case of NaCl solutions, SP= - 71 log (a1)m/(a2)m

Jan 1, 1958

By Joseph L. Gillson

BRAZIL has had an industry based on ocean beach deposits of heavy minerals containing monazite, zircon, rutile, and ilmenite for well over 40 years, but except at the very earliest period, prior to 1906, and again during World War 11, has this industry been at all comparable in size with similar operations in other countries. Limiting factors have been neither a lack of reserves nor lack of markets (except for zircon). Although poor local transportation and shipping facilities have handicapped the development in Brazil, these conditions were perhaps equally bad (when mining operations started) in the Indian State of Travancore, and in New South Wales and Queensland, Australia, in which states the principal production of beach deposits of heavy minerals has occurred. The outstanding restraints on the Brazilian industry have been the lower quality of the Brazilian minerals, the relative small size of individual deposits that were known until recently, the lack of interest of Brazilian investors in mining ventures, and the unfavorable climate for investment of foreign capital under Brazilian mining law. The lower quality of the minerals is indicated by the fact that the Brazilian monazite carries only 5 to 6 pct Tho2*, and the ilmenite 561/2 pct TiO2, whereas the corresponding Travancore minerals carry 9 pct Tho, and 60 pct TiO, respectively. The Brazilian zircon is a dirty brown color (which can be removed readily) as compared with the gleaming whiteness of the Australian zircon. An inadequate market for the abundant zircon that will be available in any operation in Brazil is certainly a heavy restraint, since otherwise it could be an important byproduct. The oxide of zirconia, baddeleyite, that has come from Brazil is from other sources.' Since the Brazilian beach sands carry only a little rutile, that mineral has not been available as a valuable byproduct to help finance the operations. Substantial tonnages of rutile have been exported from Brazil. The sources of this mineral are stream placers and residual deposits over gneisses in the States of Goyaz, Minas Geraes, Ceara, etc. (Leonardos,' and Chambers". With these handicaps, Brazilian production from beach sands has been marginal, and there has been only one consistent producer. This is a company, originally French, which was called Companie de Franco-BrazilliCne, but, with the downfall of France in 1940, became Brazilian under the name Monazita e Ilmenita do Brasil ("Mibra"). This company has operated several deposits in the vicinity of Guara-pary, in the State of Espirito Santo. Its office and plant has been at Guarapary. Recently a company called, "Fomil" (Fomento Monazita-Ilmenita) started operations. This company was organized by the Foote Mineral Co. of Philadelphia, and such share as a foreign company can hold under Brazilian law has now been acquired by the Lindsay Light and Chemical Co. of Chicago. When the writer went to Brazil in the fall of 1940, he found that no general survey of the beaches had been made except for a thorough study of part of the area by Abreu.4 The paper by Miranda6 had not then been written. The federal Geological Survey and Department of Mines knew only of the existence of the deposits in Espirito Santo south of Vitoria, and had a hazy idea that others might be found north of Vitoria. One deposit in Bala was known in Rio, but the larger one at Guaratiba was not known, although a Frenchman had prospected

Jan 1, 1951

By Joseph L. Gillson

BRAZIL has had an industry based on ocean beach deposits of heavy minerals containing monazite, zircon, rutile, and ilmenite for well over 40 years, but except at the very earliest period, prior to 1906, and again during World War 11, has this industry been at all comparable in size with similar operations in other countries. Limiting factors have been neither a lack of reserves nor lack of markets (except for zircon). Although poor local transportation and shipping facilities have handicapped the development in Brazil, these conditions were perhaps equally bad (when mining operations started) in the Indian State of Travancore, and in New South Wales and Queensland, Australia, in which states the principal production of beach deposits of heavy minerals has occurred. The outstanding restraints on the Brazilian industry have been the lower quality of the Brazilian minerals, the relative small size of individual deposits that were known until recently, the lack of interest of Brazilian investors in mining ventures, and the unfavorable climate for investment of foreign capital under Brazilian mining law. The lower quality of the minerals is indicated by the fact that the Brazilian monazite carries only 5 to 6 pct Tho2*, and the ilmenite 561/2 pct TiO2, whereas the corresponding Travancore minerals carry 9 pct Tho, and 60 pct TiO, respectively. The Brazilian zircon is a dirty brown color (which can be removed readily) as compared with the gleaming whiteness of the Australian zircon. An inadequate market for the abundant zircon that will be available in any operation in Brazil is certainly a heavy restraint, since otherwise it could be an important byproduct. The oxide of zirconia, baddeleyite, that has come from Brazil is from other sources.' Since the Brazilian beach sands carry only a little rutile, that mineral has not been available as a valuable byproduct to help finance the operations. Substantial tonnages of rutile have been exported from Brazil. The sources of this mineral are stream placers and residual deposits over gneisses in the States of Goyaz, Minas Geraes, Ceara, etc. (Leonardos,' and Chambers". With these handicaps, Brazilian production from beach sands has been marginal, and there has been only one consistent producer. This is a company, originally French, which was called Companie de Franco-BrazilliCne, but, with the downfall of France in 1940, became Brazilian under the name Monazita e Ilmenita do Brasil ("Mibra"). This company has operated several deposits in the vicinity of Guara-pary, in the State of Espirito Santo. Its office and plant has been at Guarapary. Recently a company called, "Fomil" (Fomento Monazita-Ilmenita) started operations. This company was organized by the Foote Mineral Co. of Philadelphia, and such share as a foreign company can hold under Brazilian law has now been acquired by the Lindsay Light and Chemical Co. of Chicago. When the writer went to Brazil in the fall of 1940, he found that no general survey of the beaches had been made except for a thorough study of part of the area by Abreu.4 The paper by Miranda6 had not then been written. The federal Geological Survey and Department of Mines knew only of the existence of the deposits in Espirito Santo south of Vitoria, and had a hazy idea that others might be found north of Vitoria. One deposit in Bala was known in Rio, but the larger one at Guaratiba was not known, although a Frenchman had prospected

Jan 1, 1951

By W. A. Tiller, D. H. Lane

A simple zone melting technique for investigating the effect of ultrasonic irradiation upon ingot solidification is described. The effect of i) ultrasonic power level, ii) freezing velocity, iii) constant or variable frequency, iv) direction of irradiation, and v) transducer-cozlpling bar joint upon the grain size of type 316 stainless steel have been investigated. The results of this study support the postulate that the ultrasonic vibrations increase the nucleation probability in the layer of liquid adjacent to the freezing interface. In the first paper of this series,l the possible mechanisms whereby ingot structure may be altered by irradiating a solidifying melt with ultrasonic vibrations have been discussed. A new technique for efficiently introducing the ultrasonic energy into the solid-liquid interface region was presented and applied to ingot preparation by the consumable-electrode arc-melting technique. The experimental results support the postulate that the ultrasonic vibrations may refine the ingot structure by increasing the nucleation probability in the zone of liquid adjacent to the solid-liquid interface. The present paper describes the application of the same technique to a relatively simple laboratory-scale zone-melting apparatus. This apparatus is found to be well suited to the detailed study of ultrasonic technology in this area and allows one to determine, in particular, the minimum ultrasonic power level needed to produce a certain grain size in a particular material. The results of this study support the nucleation mechanism for grain refinement, but do not provide any deeper insight into the specific nucleation mechanism responsible for the effect. EXPERIMENT The apparatus used in these experiments is shown in Fig. 1 and illustrated schematically in Fig. 2. The material to be studied, type 316 stainless steel, was in the form of a 3/4-in. sq bar 30 in. long. This bar was placed in a square open-topped mold with open ends made from high-purity graphite coated with a flame-sprayed Al2O3, skin. Surrounding the crucible was a molybdenum susceptor with 3/8-in. diam holes spaced at 1-in. intervals along its length to serve as sight ports. A tapered transducer horn was brazed to one end of the specimen. The entire assemblage was enclosed in a quartz tube, the transducer itself projecting out one end and resting in a cooling tank. A vacuum seal between the coupling bar and the end plate enclosed one end. A similar plate and seal enclosed the other end. The system is gas tight and can be operated under vacuum or an inert atmosphere. For these experiments, flowing argon at 15 in. of Hg pressure was used. The heat source for melting the stainless steel specimen was a 2-in. long 3-kc induction coil placed around the quartz tube; this source heated the susceptor, inductively melting about a 3-in. zone of the sample by radiation. To move the molten zone at a specified rate, the induction coil was moved down the tube at this rate with the aid of a simple pulling device. Thus, the sample could be irradiated at varying ultrasonic frequencies and power levels and could be solidified at varying rates. The power input to the transducer was measured using a "John Fluke Model 120 VAW-Meter." 1 The power delivered to the interface region is probably only about 50 pct of that measured on the VAW-meter. In a typical run, when the ultrasonic power was turned on, the interface of the molten zone closest

Jan 1, 1961

By C. H. Gorski

A method for preparing titanium tetrachloride is described which consists of reducing rutile with coke and chlorinating the reduced product at 200° to 500°C. The crude distillate is purified by treatment with copper powder and distillation. Recoveries, exceeding 90 pct of the titanium in the rutile, were obtained. IN recent years considerable interest in metallic titanium has been aroused because of its outstanding physical and chemical properties. The present commercial processes for preparing titanium are modifications of the Kroll1 process and consist essentially of the reduction of titanium tetrachloride with magnesium in an inert atmosphere to produce metallic titanium with magnesium chloride as a byproduct. At present,' commercial titanium tetrachloride costs $0.32 a pound, which makes the price of the included titanium $1.28 a pound. As the titanium tetrachloride must be purified further before processing into metal, its ultimate cost obviously will be higher. Consequently, one of the prime requisites for the production of lower cost titanium metal is a source of low-cost titanium tetrachloride. Recently, Knickerbocker, Gorski, Kenworthy, and Starliper3 escribed a method for preparing titanium tetrachloride from low-grade Arkansas rutile by smelting the rutile with pyrite and coke to form a titanium matte and then chlorinating the titanium matte to prepare a crude titanium tetrachloride. This process had several inherent advantages. Low-grade rutile concentrates were utilized, the chlorination temperature was relatively low (approximately 200°C), and the reaction was strongly exothermic. However, this process had several disadvantages, chief of them being the rather low recoveries of titanium tetrachloride (65 to 81 pct) and the difficulty in purifying the crude titanium tetrachloride obtained. Because of the high-titanium and low-iron con- tents of rutile as compared to ilmenite, rutile should be of greater potential value as a source of titanium tetrachloride than ilmenite. Rutile, however, is not chlorinated directly in commercial practice, because reaction temperatures above 700 °C are required, at which point chlorine attacks most of the common materials of construction. The process now in use consists of converting the titanium in rutile to the cyanonitride by high-temperature reduction in an electric furnace, and then chlorinating this compound. The disadvantages of this process are the difficulty of producing the cyanonitride, the use of high-grade rutile concentrates in the charge, and the presence of several percent of silicon tetrachloride in the finished product. It would be of considerable interest to develop a new process for the preparation of titanium tetrachloride from rutile by chlorination at 200" to 500°C. Process Development Several investigators'-' have studied the reduction of titanium dioxide with carbon in an effort to prepare titanium monoxide. Invariably, the titanium monoxide formed in this manner was not pure, as it contained titanium carbide and one or more of the lower oxides of titanium. As these lower oxides of titanium are more reactive chemically than rutile, and as it is known that titanium carbide may be chlorinated readily, a study was made of the chlorination of carbon-reduced rutile. A sample of rutile concentrates from Hot Spring County, Ark., containing 76.19 pct TiO,, 5.65 pct Fe2O3, 4.18 pct SiO2, and 2.88 pct Al2O3, was used for this investigation. The experimental procedure consisted of making an intimate mixture of —100-mesh rutile and petroleum coke, adding water and molasses as a binder to foi-m a paste, charging into a graphite crucible that was covered, except for a vent to allow the

Jan 1, 1952

By d&apos, K. Mukherjee, C. R. Antonio, R. J. Maciag, G. J. Fischer

Tensile data indicate that over the range of strain rates 10-5 to 10-1 sec-1 and in the temperature range 298° to 743°K the flow stress at a given temperature may be expressed as: C0 = Cem where m changes abruptly at a critical strain rate of 10-2 sec-1. The Zener-Hollomon parameter was tested and found to be invalid except at temperatures exceeding 700° K. Values of AH calculated for temperatures above 700°K ranged from 30 to 47.5 kcal per g-mole. ThE flow characteristics of aluminum and aluminum alloys as a function of temperature and strain rate have been of interest to various experimenters for many years. Trozera et al.1 determined tensile flow curves for pure aluminum and concluded that the combined effect of temperature and strain rate on the flow stress could be related using the Zener-Hollomon parameter. More recently, Hockett2 proposed a relationship between compressive flow stress, temperature, and true strain rate which could be represented by a surface. Holt et al.3 studied strain rate effects on flow stress in a number of aluminum alloys at room temperature. It was determined that there is a critical strain rate above which a strain rate effect is observed. It was also reported that the strain rate sensitivity was significant in aluminum alloys in the "0" condition only. In a recent review paper McQueen4 has considered a number of mathematical expressions which have been used to describe the relationship between stress, strain rate, and temperature. These expressions have been applied to the flow characteristics of a number of different metals and alloys including aluminum. In the present work the strain rate sensitivity of 7075-0 aluminum was determined in the temperature range of 298° to 743°K. The tensile flow stress at 0.2 pct offset was obtained over a nominal strain rate range of 10-5 to 10-1 sec-1. EXPERIMENTAL Threaded tensile specimens were cut from a single heat of 7075-T6 aluminum. The composition of this heat is given in Table I. The test bars had a gage section 1.5 in. long by 0.250 in. diam and conformed to ASTM specification E-8-57T. After machining, the bars were annealed at 413° ± 10°C for 2 hr. They were then cooled to 260°C in 3 hr, and finally air cooled to room temperature. This treatment is commonly used to produce the "0" condition. Load-time curves at constant crosshead speeds were obtained at various temperatures using an Instron testing machine. Crosshead speeds ranged from 0.002 to 40 in. per min. A three-zone resistance tube furnace was used for the elevated-temperature tests. Temperatures were measured at three points along the gage length by means of suitably placed thermocouples. Each tensile bar was held at temperature for 30 min prior to testing and the maximum temperature variation along the gage length was kept below 1°C. In all, 275 samples were tested and each data point plotted is an average of at least two tests. In many cases the point represents up to six tests. RESULTS AND DISCUSSION Values of the flow stress at 0.2 pct offset at six different temperatures are plotted vs strain rate on log-log coordinates in Fig. 1. Over discrete ranges of strain rate, the data for each temperature fit the expression:

Jan 1, 1969

By W. D. Forgeng, R. E. Grace

The rate of copper corrosion in liquid lead was studied as a function of flow rate and temperature in a closed isothermal loop system between 350" and 500°C. Kinetic data were interpreted with the Nernst-Brunner equation and the Chilton-Colbum mass transfer analogy to heat transfer. Over the range of temperatures and flow rates employed the solution rate constant varied from 2 x 10-3 to 20 x 10-3 cm per sec. The rate constant was found to vary with the 0.76 power of the Reynolds number in the range 7500 < Re < 40,000. The results of this investigation indicate that the Cu-Pb corrosion process is controlled largely by diffusion across a boundary layer. particularly at the higher temperatures. The effective boundary layer for diffusion is found to be approximately three to four times smaller than the momentum boundary layer. CORROSION by liquid metals has long been a problem during melting, static containment, and casting. Recently, considerable emphasis has been placed on the understanding of liquid metal corrosion mechanisms in an effort to prevent mass transfer and eventual failure in liquid metal heat exchangers and in liquid-metal-fueled nuclear reactors. The present investigation was conducted to determine the relationships which exist between corrosion kinetics and hydrodynamic conditions in an isothermal loop containing a simple liquid metal-solid metal corrosion system. The Cu-Pb system was chosen for its simplicity and ease in handling. Previous isothermal Cu-Pb corrosion studies1-3 have been conducted in both static and dynamic systems but not under conditions which allow easy "scale-up" to engineering systems, such as liquid metal heat exchangers. On the other hand, most liquid metal loops which have been used to evaluate mass transfer rates4 have been driven with temperature gradients under conditions of natural convection and unknown flow rates. The primary contributions of this research are twofold: 1) to evaluate the design of a simple isothermal loop corrosion system and 2) to investigate liquid metal corrosion behavior under well-defined hydrodynamic conditions. MATERIALS AND EXPERIMENTAL WORK The apparatus used to measure the Cu-Pb corrosion rates is shown schematically in Fig. 1. The loop system consisted of 1) a reservoir made of Type 316 stainless steel containing a centrifugal pump and 2) stainless-steel tubing containing a removable copper test section. The copper test section was OFHC hard-drawn tubing, 11.0 0.05 cm in length and 0.775 ±0.005 cm ID. A Type 316 stainless-steel venturi meter* was inserted in place of the copper test sec- tion in order to determine the lead velocity as a function of pump speed at each temperature. The Cu-Pb system was chosen for this study because the solubility of copper in liquid lead is large enough to measure accurately but small enough that the diameter of the copper tubing was not changed significantly by corrosion. There are no intermediate phases formed in the system, and the solid solubility of lead in copper is vanishingly small so that back-diffusion cannot occur. Molten lead (corroding grade; 99.94+ pct Pb, 0.0015 max pct Cu) was charged from an auxiliary melting furnace into the system under an argon cover to minimize oxidation. The lead was then maintained at constant temperature by a stirred molten salt bath in which the loop was immersed to a depth just above the lead level in the reservoir, Fig. 1. The total volume of lead in the system was 320 2 cu cm.

Jan 1, 1969

By H. R. Brannon, R. J. Robinson, G. W. Kattawar

Accurate prediction of storm wave characteristics are needed for design of offshore structures. Statistical methods of random noise analysis provide techniques for predicting required wave properties. These techniques have been used to analyze and characterize storm wave profiles from Gulf of Mexico recording installations in 34, 65 and .98 ft of water. Correlations based on the results can be used to predict wave crest probabilities and wave shapes for a range of Gulf water depths and storm conditions. Example predictions of wave crest probability as a function of water depth for a particular set of storm conditions are given. INTRODUCTION Accurate predictions of wave crests and wave shapes are needed for design of offshore structures. With predictions of wave crests, platform deck elevations giving adequate protection from exposure to storm waves can be selected. Use of hydro-dynamic wave theories with the wave crest and wave shape predictions permits an estimate of the wave forces an offshore structure must withstand. Observation of ocean waves suggests use of statistical analysis for studying wave characteristics for water depths beyond the breaking wave zone; recent wave generation theories lend support to this approach. l-3 One of the most powerful methods of statistically analyzing wave profiles was introduced by Cartwright and Longuet-Higgins; most of the basic relations used were developed by Rice5.6 in studies of random noise theory. This method predicts wave crest elevation probabilities from two parameters characterizing a wave profile. The statistical approach also provides a means for predicting wave shapes. In the random noise model of a wave profile, surface elevation is represented as an infinite sum of sine waves with closely spaced frequencies and random phase angles. Power density is proportional to the sum of the squares of the amplitudes of sine waves having frequencies within a narrow band, and the distribution of power density as a function of frequency is called the power density spectrum, or power spectrum. The power spectrum characterizes an irregular sea, and hence finds use in motion studies of ships, barges and semisubmersible drilling platforms. From the power spectrum, a wave profile of any duration of time can, in principle, be calculated; this long wave profile depicts the many wave shapes to which a structure may be exposed. Thus, the statistical methods of wave analysis provide an approach to selecting wave shapes as well as wave crest elevations needed for design of offshore structures. For practical application of these techniques, power spectra and related quantities must be predicted from storm properties. Barber and Tucker 7 have reviewed correlations of wave properties and storm conditions. Their review summarizes work of Darbyshire,8 among others, in which a correlation of power spectra with wind intensity of the North Atlantic was developed. These results, plus more recent work by Pierson and Moskowitz and Kitaigorodskii,10 establish feasibility of correlation, but there is no theoretical basis for modifications extending the relations to other areas as remote as the Gulf of Mexico. Hence, to predict characteristics of Gulf of Mexico waves, a study of local observations is needed. This paper presents (1) a practical approach to computing wave profiles hat depict shapes of waves for use in force calculations, (2) a summary of relations for predicting probabilities of wave crest elevations, (3) correlations of parameters needed to apply these methods in the Gulf of Mexico and (4) examples of application of the techniques. THEORETICAL BACKGROUND The following sections summarize relations needed to calculate wave profiles and to estimate wave crest probabilities. These relations also identify quantities that must be related to storm

By J. H. Jackson, P. D. Frost, C. H. Lorig, A. C. Loonam

THIS paper describes (1) the effect of sodium on the tensile ductility of magnesium-lithium base alloys, and (2) the precautions necessary to avoid sodium contamination. Effect of Sodium on Properties The harmful effect of sodium in magnesium-lithium base alloys has been recognized by other investigators.1,2 However, quantitative data on its effect have not hitherto been published. The effect of sodium on the ductility of an 87 pct Mg-9 pct Li-4 pct Zn alloy is shown in fig. 1. The sodium was introduced by adding sodium chloride to the flux, which consisted of 50 pct LiC1-50 pct KC1. Moderately high ductility was obtained at an indicated sodium content of about 0.05 pct. Actually, the value probably was less than 0.05 pct, be-cause analyses of the lithium, which were more accurate than those of the alloy, indicated that the highest ductility was obtained when its sodium content was 0.02 pct or less. In fact, in alloys having somewhat greater strength than this particular composition, the sodium content of the lithium must be under 0.01 pct to avoid embrittlement. The effect of sodium on the ductility of several alloys having fairly low strength levels is shown in fig. 2. These alloys were melted with a flux containing 75 pct LiC1-25 pct LiF, to which various quantities of sodium chloride had been added. Sodium had no significant effect in pure magnesium but markedly decreased the ductility of the magnesium-lithium-zinc alloy, even though the alloy contained only 3 pct Li. As the lithium content of the binary alloys was increased, the ductility of the sodium-free alloys also increased. However, the effect of sodium on ductility became progressively more pronounced. Sodium raised the minimum hot-rolling temperatures, particularly those of the high-strength alloys, but its effect, in this respect, was less critical than its effect on tensile ductility. For optimum cold roll-ability, a low-sodium content was required. No deleterious effect of sodium on the stability of properties at slightly elevated temperatures was found. Control of Sodium in the Alloys Optimum ductility is obtained in the magnesium-lithium base alloys when sodium-free materials are used. Commercial lithium was formerly the chief source of contamination. Now purified lithium is usually available. When lithium of ordinary purity is used, the effects of sodium can be minimized by using a flux consisting of 75 pct LiC1-25 pct LiF. Bubbling nitrogen through the melt also helps remove sodium. The damaging influence of sodium on the ductility of the magnesium-lithium base alloys was observed very early in the alloy development program. The discovery came about as a result of chemical analyses made on the lithium used in the alloys. Ductile alloys had been made from lithium containing about 0.2 pct Na, whereas the lithium used in the brittle alloys contained about 0.9 pct Na. The first magnesium-lithium alloys were melted under commercial fluxes ordinarily used in melting magnesium alloys. These fluxes were unsuited for scavenging the contaminating sodium, and the resulting alloys were not ductile. Next, a flux containing 50 pct KC1-50 pct LiCl was tried. This was somewhat more effective but still was not satisfactory. After a number of different experimental fluxes had been investigated, one containing 75 pct LiC1-25 pct LiF was adopted. This flux made it possible to obtain good ductility in the alloys. The

Jan 1, 1951

[A session of the Institute of Metals held during the February, 1926, meeting of the Institute, was devoted to a symposium on &apos;&apos;gas" in copper. S. Skowronski, Perth Amboy, N. J., was chairman. On the program were papers by T. S. Fuller; W. H. Bassett and J. C. Bradley; Susan B. Leiter, and W. H. Bassett and H. A. Redworth. These papers follow the chairman&apos;s introductory discussion.] S. Skowronski, Perth Amboy, N. J.—There are today two groups of metallurgists, one group who believe in oxygen-free copper and another group who believe that oxygen is absolutely essential in copper; not that the two groups disagree, but that a certain grade of work calls for oxygen-free copper, while another grade of work does not. I can sum up the problem by reading the abstract of an article by Frederick Johnson of Great Britain in The Metal Industry of Sept. 4, 1925. Few, who have watched the trend of things during the last two decades, can have failed to notice the steady growth of opposition to the prevalent use of copper in the "tough-pitch" condition, which for many ages enjoyed an unchallenged supremacy. Broadly speaking, there are two schools of thought in the metallurgical world, one holding the view that copper containing a small proportion of oxygen is an eminently suitable material for users, the other expressing its preference, in no hesitating or uncertain manner, for copper from which oxygen has been removed by means of a deoxidizer. In the old days, before the advent of the converter and the electrolytic refining process, the copper of commerce was so impure that the presence of oxygen was imperative in order to neutralize the influence of impurities which militated against the hot-working properties of the metal. For electrical purposes, oxygen must be present, because sound bars and billets cannot be produced without it, except at the expense of electrical conductivity. For most engineering purposes, however, electro-deposited copper may be used either by itself or with the addition of alloying elements, e. g., arsenic and nickel, which experience has proved to be beneficial, such copper being freed from oxygen by the aid of a deoxidizer, e. g., phosphorus. Such material has positive advantages over "tough-pitch" copper as at present produced from refinery furnaces. It has greater toughness and malleability, and is immune from the action of reducing gases at high temperatures, the destructive action of which, in the case of "tough-pitch" copper, is well known. The reasons why there has been no wholesale replacement of "tough-pitch" copper by deoxidized copper are commercial in nature; copper can be more economically melted in large-capacity furnaces which lend themselves to the poling process and are not so suitable for control of uniformity of action of deoxidizers as the smaller electric or crucible furnaces, whilst they are also more convenient for the production of very large castings. Moreover, the equipment of most large copper manufacturing plants is designed for casting "tough-pitch " copper in open moulds, e. g., wire bars and cakes, and these could not be used for deoxidized copper, which must be cast in vertical moulds as in brass-shop practice. Further, there are still certain impure brands and

Jan 1, 1926