Search Documents

By Irwin R. Higgins

CONTENTS A. Introduction B. System Description C. Uranium Pilot Plant Programs D. Summary INTRODUCTION The Chem-Seps Continuous Countercurrent Ion Exchange (CCIX) contactor was first conceived of in 1951 at the Oak Ridge National Laboratory. In the 27 years that have passed, there has been a steady stream of pilot plant process development studies on a variety of processes far too numerous to mention. These have been in the area of water and waste treatment, chemical processing, ore leach treatment, and many others. Many successful production systems have been installed and operated in a variety of applications. A few of these are described herein together with a description of the system and its operational characteristics. SYSTEM DESCRIPTION Chem-Seps Continuous Countercurrent Ion Exchange* is a single loop in which various sections are separated by valves to isolate the sections performing different functions simultaneously. (Refer to Figure 1). To explain the working of a typical unit, let us use a simple configuration used in water softening or demineralization. The resin is moved in small increments by the hydraulic ram action. All solution flows are countercurrent to the flow of resin. The contaminants are removed in the process cycle and the resin is moved in the pulse cycle. A controller in the effluent stream from the treatment section senses the proper limit permissible in the effluent. In the process cycle, the influent enters through a set of distributors, moves downward and leaves through a set of collectors. Simultaneously the regenerant enters through valve RE and leaves through valve WA. The rinse enters through valve RI and its duration is controlled by an interface controller. In the process cycle, valves B, C, and D are closed, isolating all the sections. The duration of the process cycle is 4-10 minutes depending on the contaminants to be removed and is controlled either by a timer if the contaminants are fixed, or a controller in the effluent stream, if the contaminants fluctuate at short intervals. Valve A is open and resin is dropped to the pulse section simultaneously with the removal of contaminants in the treatment section, regeneration of loaded resin in the strip section, and rinsing of regenerated resin in the rinse section. As the resin drops through the valve A, it is backwashed to remove the suspended solids or resin fines. Removal of these fine particles is important to avoid the unnecessary pressure drop in the bed and plugging of the distributors. At the end of process cycle, all flows going into the unit and out of unit are automatically shut off. The valve A closes and valves B, C, and D open in proper sequence. A slug of water enters through valve PU, a predetermined incremental volume of resin moves into the regeneration section, an equal volume of regenerated and rinsed resin enters the bottom of the treatment section, and an equal volume of the loaded resin leaves the top of the treatment section and goes into the resin reservoir section. (The resin movement is plug flow with the Reynold's number being in the laminar region of the curve, and no fluidization occurs during the pulse cycle.) The total time required for proper sequencing of valves and the movement of resin is 20-30 seconds. At the end of this period, the valves B, C, and D close and valve A opens. The solution valves open and normal steady state operation begins. All valves are interlocked and properly sequenced. The resin movement is precisely controlled by sonic devices. Special Features of Chem-Seps CIIX "Downflow"*: The raw feed in the treatment section moves downward and the resin moves upward in the treatment section. The "downflow" of feed overcomes the handicap encountered in "upflow" systems. The "upflow" of feed requires a certain minimum flux during process cycle to lift the bed and keep it

Jan 1, 1979

By V. K. Grotzky, F. J. Fraikor

A number of investigators have noted the importance of various precipitation reactions on the properties of commercial-purity beryllium.1-5 Carrabine, for example, has demonstrated the interaction of iron and aluminum on the mechanical properties of hot-pressed polycrystalline beryllium.6 He considered the determining factor on elevated-temperature properties to be a reversible AlFeBe, precipitation reaction which could be directly related to the Fe/Al impurity ratio of the beryllium. Any aluminum in excess of the stoichio-metric amount required to form A1FeBe4 was presumed to remain primarily in the grain boundaries. We have observed, by transmission electron microscopy, such a grain boundary effect after various heat treatments of beryllium sheet. The starting material in this investigation was bare-rolled beryllium ingot sheet (0.001 to 0.005 in. thick), in contrast to the hot-pressed powder utilized by Carra-bine. It should be noted from the ingot sheet analysis shown in Table I that the Fe/Al weight ratio was near unity which would provide some free aluminum although the total aluminum and iron content was still small. Fig. l(a) shows some aluminum or aluminum-rich precipitates in the grain boundaries of a beryllium foil which had been quenched from 1200°C into brine at -TPC. Similar grain boundary precipitates were found, particularly at grain boundary intersections, in other samples quenched from 1100° and 1000°C. The length of annealing time at these elevated temperatures did not appear to substantially alter the amount of grain boundary precipitates, thus attesting to their relative insolubility. No matrix precipitates were observed other than the normal BeO and Be2C inclusions. A microprobe analysis of the larger precipitates at

Jan 1, 1968

By Charles Barrett

PLASTIC flow in metal crystals and the changes in orientation resulting from it are generally understood to take place by the following funda-mental mechanisms: (1) slip on crystallographic planes, (2) homogeneous crystal rotation resulting from the slip, (3) bending of the lattice between the planes of slip, and, under certain circumstances, (4) twinning. This paper and a preceding one on iron subjected to uniaxial compression1 concern two additional processes that must now be added to this list: (5) the formation of deformation bands, and (6) the bending and rotation of these bands. The present investigation yields a new understanding and definiteness to the common terms so loosely used when speaking of cold-worked metals -"grain fragmentation," "elongated grains," and "deformation twins," "deformation bands," "etch bands," or "X-bands." Bands have been noted on the polished and etched surfaces of cold-worked metals by vari-ous investigators for more than 25 years, ? yet their nature and their significance have been so little understood that they are not treated in the most comprehensive modern texts on the deformation of crystals. The experiments in this series show that they are one of the fundamental processes in the deformation of metals, of importance in the development of preferred orientations, in work-hardening (since they have the effect of reducing the effective grain size and interfering with slip), and in the recrystallization process. The present experiments were performed on the same stock of mate-rial that was used in the earlier compression experiments1-hydrogen-purified mild steel in which the carbon content had been reduced to the limit detectable under the microscope and in which single crystals could be grown by a strain-anneal treatment.2

Jan 1, 1939

By G. H. Edmunds, C. H. Mathewson

About fifty pages of Henry M. Howe's profound treatise, "The Metallography of Steel and Cast Iron," are devoted to twinning with special reference to the origin, nature and general significance of the Neumann bands in ferrite. Howe believed with Osmond and Cartaud1 that the Neumanns are mechanical twins and his careful observations leave no doubt that these straight-sided narrow bands habitually occur parallel to trapezohedral planes of form {211). Attempts to develop the structure of the bands by various methods SO that their identity could be established beyond question have not been conspicuously successful. Howe thought that they deflected slip bands. Some of the etching figures which have been developed within and adjacent to Neumann bands support the contention that they are twins. A good example of this effect in ferrite containing 0.6 per cent, of niekel and 1.3 per cent. of phosphorus, originally due to Harnecker and Rassow,2 was reproduced in the 1928 lecture before the Institute of Metals Division on twinning in metals.3 In this case, the sides of the figures might represent the traces of cubic planes laid bare by etching a properly oriented grain of ferrite, twinned along a plane of form (211). Our own observations in this direction may be represented by Fig. 1 which shows in a deeply etched cavity in the boundary region between a Neumann band and the original crystal two small crystal surfaces which resemble the faces meeting at a reentrant angle in the simple cube twinned along a bisecting plane of form (211) as sketched in Fig. 2. Rosenhain and McMinn4 in 1925, after a careful study of slip bands in ferrite containing Neumanns previously produced by shock, concluded

By Samuel Daniels

Aluminum-base alloys containing small amounts of copper and magnesium possess but ordinary physical properties as sand cast, but may be treated to give a remarkable range of tensile values and of Brinell hardness. The high-copper (4.5 per cent.) duralumins must be given a protracted treatment which in nature resembles the malleableizing of white cast iron; the low-copper (2.25 per cent.) duralumins develop an excellent combination of strength and ductility with a treatment which requires a maximum of 5 hr. to be completed. THE wrought alloys of aluminum with small amounts of copper and of magnesium have, with the development of the automotive and aircraft industries, sprung into prominence through the medium of duralumin; but the cast alloys remained in the background because their possibilities in the heat-treated condition were either not recognized or not fully investigated. In 1919, the Bureau of Standards published a preliminary survey1 of this field, which pointed out that, in general, the ultimate strength and the percentage of elongation of the alloys of aluminum with and without magnesium could be improved by so simple a treatment as heating to 932° F. (500° C.) for 2 hr., cooling in, air, and aging at room temperature for several days. British investigators, too, working with chill-cast material, found that " considerable improvement in the mechanical properties of copper-aluminum alloys' may be obtained from suitable heat treatment applied to castings."2 Jeffries and Gibson3 made the first contribution to the literature dealing exclusively with the heat treatment of sand-cast aluminum-base alloys, describing the effect of small additions or of combinations of copper, magnesium, and iron on the response to a short heat treatment comprising heating at 932° F. in a

Jan 7, 1924

By G. R. Fritterer

Investigators in the field of temperature measurement have long sought a thermoelectric couple fulfilling the following requirements: 1. It should be useful up to and including high industrial temperatures; i. e., 1000 to 1800 C. 2. Its thermoelectric variation with temperature should be linear and be maintained after heating to high temperatures for long periods of time. 3. It should be reproducible; i. e., different couples of the same elements should have similar calibration curves. 4. Its thermoelectric power should be large so as to allow the industrial use of rugged recording instruments. 5. Chemical reactions with, and physical changes within the elements of the couple should not alter its calibration. No thermocouple proposed to date exhibits simultaneously all of these characteristics, whereas the couple about to be described fulfills all requirements to a satisfactory degree. New Thermoelectric Materials A thorough survey of the literature on thermoelectricity revealed that present-day thermocouples could not meet the specifications mentioned above because their thermoelements are metallic. Metals have a marked tendency to deteriorate chemically and their melting points limit their use to low temperatures. Refractory substances, however, are usually resistant to chemical attack and are quite stable at high temperatures. Hence a survey of refractory substances having thermoelectric possibilities was made. One class of thermocouples considered was that in which carbon and a carbide of some metal or nonmetal were the thermoelements. Previous investigators neglected to study this field but certain recommendations were made by them for the use of couples in which carbon served as one element. These proposals are listed in Table 1. The couples suggested are unsatisfactory because of their low thermoelectric powers, the low melting points of their metallic elements, etc. The

Jan 1, 1933

By H. W. Miller, V. H. Wilhem

Although the year 1933 was a period of uncertainty, considerable new development was initiated, with a high percentage of favorable results, for owing to financial conditions only projects of merit were proposed and developed. Unfavorable marketing conditions caused severe financial losses to refinery and sales departments of nearly all companies during the first half of the year. In anticipation of stabilized Government control, earnings were generally favorable during the third quarter but failure of the Government to take legal action against violators of the proration orders, and lack of agreement on a definite plan of curtailment, resulted in considerable overproduction and demoralization of the market structure during most of the final quarter. However, toward the close of the year Government action against violators of the Oil Code had a tendency to decrease overproduction materially and give the market a firmer tone. As a whole, the price structure of crude oil was maintained at a high level during the year; in fact, at a much higher level than the price of refinery products warranted. At no time during the year was production within 10,000 bbl. daily of the state allotment, overproduction of crude reaching a peak of 70,000 bbl. on Sept. 7, average daily average for the year being about 27,000 barrels. Numerous plans for equitable curtailment were prepared and tested during the year, none of which fully solved the many and intricate problems faced by operators who were in most cases willing to curtail if they could feel that cooperation was being practiced by their neighbors. Outstanding events in California oildom during the period under discussion may be classified under the following headings: 1. New discoveries. (a) New development in proven areas. (b) Deeper zones in settled pools. 2. Unproductive wildcat operations. 3. Whipstocking practice and procedure. 4. Progress of unit and orderly plans of development.

Jan 1, 1934

By K. B. Nowels

DATA pertaining to pipe line flow for both oil and gas in horizontal or nearly horizontal pipe lines are both extensive and accurate. However, the pipe formulas used to determine pressure drop for flowing fluids (liquids and gases) under conditions of horizontal flow are not generally applicable to flowing oil and/or gas wells. Except for some data developed in small laboratory set-ups, little or no information was available concerning flow of oil and gas mixtures in vertical pipes, when, in 1928, the writer began the development of a method for computing pressure drops in the pipes of flowing oil wells, as outlined in this paper. In 1929, Uren1 presented some findings based on laboratory experi-ments in which vertical flow of an extremely heavy crude oil was induced, by means of air through a 2-in. pipe, 41 ft. long. The friction factors derived from the experiment, as well as values for pressure drop per 100 ft., are not believed satisfactory in their application to flow problems in the field. Versluys,2 also in 1929, presented a mathematical development of the theory of flowing oil wells, and in 1930, gave a companion paper3 setting forth some principles governing the choice of length and diameter of tubing in oil wells. Since the termination of the study presented in this paper, another. valuable contribution pertaining to the problem, of vertical flow was made by Moore and Wilde.4 Although there were writings dealing with the principles of the gas-lift, a search of the available literature indicated that specific information on vertical flow was lacking with the exception of the writings of Uren, Versluys, and Moore and Wilde, to which reference .has been made.

Jan 1, 1932

By Carl E. Swartz

In the course of a recent investigation1 to develop a more satisfactory white-metal bearing alloy, a number of alloy systems were studied. The cadmium-nickel system showed characteristics desirable in a bearing alloy, and the system was therefore studied in some detail. Experimental Method Alloying cadmium with nickel offered no serious difficulty. After melting the cadmium, clean sheet nickel was added while the temperature was maintained at 500" to 600" C. A few crystals of ammonium chloride2 served to clean the nickel when the latter did not "wet" readily. In preparing the individual alloys for thermal and microscopic investigation, a "hardener" containing about 10 per cent nickel was used. Thermal Experiments and Apparatus Time-temperature cooling curves were made by standard methods. Globe electrolytic cadmium was added to the hardener to make a melt of the desired composition weighing between 100 and 200 grams. This charge was placed in a Pyrex test tube, 1 by 10 in., closed with a rubber stopper carrying a thermocouple sheath and quartz stirring rod. The assembly was lowered to a depth of about 4½ in. into an electric resistance pot furnace containing a No. 0000 clay-graphite crucible (to catch the melt in case of a break in the test tube). After the tube was clamped in this position, an asbestos-magnesia mixture was loosely packed in the furnace around the tube and a "halved" cover of transite placed on top. This left at least 5 in. of the test tube protruding from the furnace. When the alloy had melted, the thermocouple was adjusted so that the hot junction was l! in. from the bottom of the test tube. The melt was stirred thoroughly for several minutes to insure composition homogeneity and absence of thermal gradients.

Jan 1, 1934

By J. D. Pennock

About a year and a half ago, Mr. Morris, an engineer of the Solvay Process Company, was sent to Belgium and France to study the manufacture of coke in the Semet-Solvay ovens, which were in operation at Havre. With complete plans of construction and a good understanding of the methods of running the ovens, he returned to Syracuse. Work on twelve Semet-Solvay ovens was immediately begun. These ovens, with plant for crushing and washing coal, and the necessary condensers, scrubbers, and concentrator for the recovery of the byproducts are nearly finished, and will soon be in operation. As the work approached completion it became necessary to determine what coal should be used. Accordingly, a chemical investigation of the various bituminous coals was made. I. Investigation of Coals. The samples of coal taken for analysis were: I. A sample of Reynoldsville coal that had been exposed to the weather for a year; 11. Reynoldsville coal taken from a car direct from the mine; 111. Morris Run lump coal; IV. Morris Run fine coal; V. Coal from the Fairmount Coal and Coke Company; VI. A special enginecoal from Pardee colliery, Phillipsburg, Pa.; VII. South Fork, Pa., coal; VIII. Coal from Laceyville, Ill.; IX. Pittsburgh bituminous coal from Ocean mines (gas-coal); X. Steubenville, Ohio, coal; XI. Evansville, Indiana, coal; XII. Coal from the Ohio Coal Company. Proximate Analysis. I. 11, 111. IV. V. VI. Water at 90° C.,* ..................................... Volatile,. .. 31.14 33.00 17.73 18.12 37.20 23.86 Fixed Carbon,. . 64.49 58.07 71.92 71.89 56.68 73.00 Ash,. .. 4.37 8.93 10.35 9.99 6.12 3.14 Coke,. .. 68.86 67.00 82.27 81.88 61.88 76.80

Jan 1, 1893

By Ben E. Lindsly

PetRoleum engineers generally are familiar with the investigations of Dow and Reistle,1 Beecher and Parkhurst,2 and Dow and Calkin3 relative to the solubility of natural gas in crude oil. Since the publication of the results of those investigations and the work of Mills and Heithecker,4 little additional knowledge on this interesting and important subject has appeared in the petroleum engineering literature. The reports of Beecher and Parkhurst and Dow and Calkin agree substantially. The data from both investigations showed that, under the conditions of the tests, the solubility of natural gas in crude oil increased in direct proportion to the pressure at which the gas was put into solution, and the solubility decreased to a considerable extent with increased temperature. These facts, and others relating to the changes in viscosity, surface tension and specific gravity of the crude caused by the solution of gas in the oil, have been given due consideration in the petroleum industry, and the recognition of these facts has resulted in a great improvement in the technique of producing oil. However, in these first experiments, various grades and types of weathered crude oil were contacted at various pressures up to 500 lb. per sq. in. gage with gases deficient to a considerable degree in the heavier hydrocarbons, as compared with the gas that was originally in solution in the oil in its natural underground reservoir. The amount of dissolved gas that was liberated upon reducing the pressure to 1 atm. was measured. For these reasons, the complete significance of the effect of dissolved gases in crude oil, as it occurs in nature, cannot be determined directly from the data obtained under the conditions of the tests as described.

Jan 1, 1931

By H. W. Knott, M. H. Mueller, P. A. Beck

The rolling and recrystallization textures in 300°C rolled uranium sheet were investigated using a Geiger counter diffractometer with the modified Schulz reflection technique. Seven sections of sheet material were used in order to obtain sufficient data for quantitative pole figures by the reflection technique. A special integrating specimen table was used for obtaining and recording the data automatically. The rolling texture was described in terms of several "ideal orientations" in which the stronger orientations have either the (1103 or (010) poles in the vicinity of the rolling direction. The recrystallization texture of the sheet uranium was also described by several "ideal orientations" which are somewhat different, except in one case, than the as-rolled "ideal orientations." RESULTS of an X-ray study of the deformation texture in rolled uranium rods were reported by Harris' in which a concentration of (010) and (110) poles was found in the rolling direction. More recently Seymour," Mitchell 'and Rowland,3 and Adam and Stephenson4 reported results obtained on uranium sheet rolled under various conditions of tem- perature and amount of reduction. Since the results of Seymour as opposed to those of the two other groups of investigators are not in full agreement, it seemed justifiable to publish the present data, obtained concurrently with the previously mentioned investigations.'-' The results with rolled and re-crystallized uranium sheet were also included in the paper, since they appear to be more complete than the only previously published texture data on recrystallized sheeL3 In the present investigation great care was taken to maintain complete separation of the reflections from different crystal planes, even in cases where the 20 angles differed from each other by less than

Jan 1, 1956

By Hsun Hu

NOT much data are available in the literature on textures in cross-rolled metal sheets. Among the body-centered-cubic metals, a few investigators have studied the preferred orientations developed in cross-rolled and in subsequently annealed molybdenum specimens.1-4 Semchyshen and Timmons5 onstructed complete pole figures for the cross-rolled and subsequently annealed arc-cast molybdenum. They used the conventional photographic method. Similar data on cross-rolled iron are still lacking. In view of the fundamental importance of iron as a basic metal for magnetic alloys and many industrial steels, the present investigation was undertaken in an attempt to understand more about its properties. The material selected for the present work was of high purity, and the textures were determined by the Geiger counter spectrometer technique, which permits the construction of quantitative pole figures. Experimental Procedure The material used for this investigation was NRC (National Research Corp.) high-purity, gas-free iron. The total gas content (N2 + O2 + H2) given was less than 0.026 pct, and the carbon content, less than 0.005 pct. Spectrographic analysis of a 2 in. cast ingot showed the percentage of metallic impurities as 0.0004 pct Cu, 0.0002 pct Mg, 0.001 pct Mn, 0.01 pct Ni, and 0.006 pct Si. A 1 in. thick slice was cut off from the 2 in. cast ingot. It was hot-forged at 850 °C to destroy most of the cast structure. Surface scale was removed by milling the forged piece to a size 2 in. long, 1½ in. wide, and ¾ in. thick. After normalizing at 915 °C for 15 min, the piece was alternately cold-rolled 40 pct and annealed at 750°C in hydrogen to a final thickness of 0.165 in., with a resulting uniform grain size of 0.1 mm.

Jan 1, 1958

By D. A. Martin, Laird Crocker, W. I. Nissen

The Federal Bureau of Mines has developed a process for removing SO2 from stack gases. The process comprises absorption of SO2 in an. aqueous solution of sodium citrate, citric acid, and sodium thiosulfate, followed by reaction of the absorbed SO2 with H2S to precipitate sulfur and regenerate the citrate solution for recycle. A pilot plant was operated at The Bunker Hill Co. lead smelter in Kellogg, Idaho, to assess the feasibility of using the process for flue gas desulfurization. Nominal capacity of the pilot plant, which treated .tail gas from the lead smelter sintering furnace, was 1699 standard meters cubed per hour (15 degrees celsius) of 0.3- to 0.7-percent-SO2 gas yielding about 272 net kilograms of sulfur per day. The pilot plant was operated for about 4500 hours and produced more than 45 net tonnes of sulfur. The operation demonstrated that (1) more than 95 percent of the SO2 could be removed from the lead smelter sintering furnace tail gases, (2) regeneration of the citrate solution with H2S and precipitation of sulfur in conventional stirred vessels was readily controlled and highly efficient, (3) the precipitated sulfur could be continuously recovered as a 99.5-percent-pure product by kerosine flotation and melting, and (4) the 77- to 79-percent-H2S gas used for sulfur precipitation could be readily produced from pilot plant product sulfur, natural gas, and steam. Projected operating costs, including capital charges, for a citrate plant, installed at a 118 000-tonne-per-year lead smelter and treating 49 271 standard meters cubed per hour of lead smelter sintering furnace tail gas, are estimated to be $384 per tonne of sulfur.

Jan 1, 1976

By B. H. Sage, W. N. Lacey, W. M. Morris

The volumetric behavior of isobutane at temperatures below its critical temperature has been studied by several investigators. Seibert and Burrelll measured the vapor pressure of isobutane from the ice point to the critical temperature. Dana and co-workers2 determined among other thermodynamic quantities the density of the saturated liquid and the saturated gas and the vapor pressure from approximately 0 to 130 F. Sage and Lacey3 studied a number of the thermodynamic properties of this hydrocarbon from 70" to 250" F. The specific volume in the gas and liquid region was determined at pressures up to 3000 Ib. per sq. in.? throughout this temperature interval. In addition, the vapor pressures were measured at 30" intervals. These data taken together serve to establish the thermodynamic behavior of isobutane at temperatures between 0" and 250" F. with reasonable accuracy. However, apparently there are no data available at the higher temperatures. For this reason an investigation of the volumetric behavior of isobutane at temperatures between 100" and 460" F. was carried out with apparatus that has been described in another paper (p. 136, this volume). Materials The isobutane used in this investigation was obtained from the Philgas Division of the Phillips Petroleum Co. That company's special analysis upon this sample indicated it to contain less than 0.03 mol per cent of impurities. In order to avoid traces of noncondensable gases, this hydrocarbon material was subjected to two successive fractionations at a high reflux ratio in a column approximately 4 ft. long and % in. in diameter, which was packed with small glass rings. The middle portion of distillate from the first fractionation was used in the second fraction-ation and a portion of the overhead from this second distillation process was repeatedly condensed at liquid-air temperatures at a pressure only slightly above the sublimation pressure of isobutane at this temperature.

Jan 1, 1940

By W. N. Lacey, B. H. Sage, W. M. Morris

The volumetric behavior of isobutane at temperatures below its critical temperature has been studied by several investigators. Seibert and Burrelll measured the vapor pressure of isobutane from the ice point to the critical temperature. Dana and co-workers2 determined among other thermodynamic quantities the density of the saturated liquid and the saturated gas and the vapor pressure from approximately 0 to 130 F. Sage and Lacey3 studied a number of the thermodynamic properties of this hydrocarbon from 70" to 250" F. The specific volume in the gas and liquid region was determined at pressures up to 3000 Ib. per sq. in.? throughout this temperature interval. In addition, the vapor pressures were measured at 30" intervals. These data taken together serve to establish the thermodynamic behavior of isobutane at temperatures between 0" and 250" F. with reasonable accuracy. However, apparently there are no data available at the higher temperatures. For this reason an investigation of the volumetric behavior of isobutane at temperatures between 100" and 460" F. was carried out with apparatus that has been described in another paper (p. 136, this volume). Materials The isobutane used in this investigation was obtained from the Philgas Division of the Phillips Petroleum Co. That company's special analysis upon this sample indicated it to contain less than 0.03 mol per cent of impurities. In order to avoid traces of noncondensable gases, this hydrocarbon material was subjected to two successive fractionations at a high reflux ratio in a column approximately 4 ft. long and % in. in diameter, which was packed with small glass rings. The middle portion of distillate from the first fractionation was used in the second fraction-ation and a portion of the overhead from this second distillation process was repeatedly condensed at liquid-air temperatures at a pressure only slightly above the sublimation pressure of isobutane at this temperature.

Jan 1, 1940

Forty-three years ago a record for low cost was made at the Spanish mine, in Nevada county, California. In 22 days of September, 1887, there was mined 2796 tons of ore at a cost of 37.5 cents per ton, of which 32.4 cents was for labor and 5.1 cents for supplies. The mill treated this ore for 23 cents per ton, of which 12.3 cents was for labor and 10.7 cents for supplies. Thus the total operating cost was 60.5 cents per ton. The yield was $1.16 in gold per ton, leaving a profit of 56 cents per ton, or 48 per cent of the yield. The mine was an open-cut in a schist formation on a hillside and the work was done by Chinese laborers that were paid $1.40 per shift. The ore was soft, and could be ground effectively in four Hunting- ton mills, supplemented by silvered amalgamating plates.* The engineer in charge was F. W. Bradley, a student from the University of California. As has been indicated, the conditions were unusually favorable in respect of softness of ore, accessibility to the mill, metallurgic simplicity, with cheap labor and power, but even at that the results were so remark- able as to attract general attention, which, as might be expected, was magnified, for advertising purposes, by the manufacturers of the Huntington mill, the firm of Parke & Lacy, at San Francisco. The record made at the Spanish mine therefore found its way into many textbooks on mining published at that time. The editor of the 'Mining and Scientific Press'† (at that date, Charles G. Yale) evidently took a warm interest in. the

Jan 1, 1932

Statistics compiled by the United States Geological Survey show that the iron ore mined in the United States in 1917 reached a total of 75,288,851 gross tons, exceeding the former record output of 1916 by 121,179 tons. The shipments from the mines in 1917 were 75, 573,181 gross tons, valued at $238,260,333, a decrease in quantity of 2,297,372 tons, or 2.95 per cent., and an increase in value of $56,358,056, or 30.98 per cent., over the shipments in 1916. The average value per ton at the mines for all grades of ore in 1917 was $3.15 as against $2.34 in 1916. Stocks of iron ore at mines, mainly in Minnesota and Michigan, amounted at the close of 1917 to 10,628,908 gross tons, compared with 10,876,352 gross tons in 1916. The quantity of pig iron, exclusive of ferro-alloys, sold or used in 1917, according to reports of producers to the United States Geological Survey, amounted to 38,612,546 gross tons, valued at $1,053,785,975; compared with 39,126,324 gross tons, valued at $663,478,118 in 1916, a decrease of 1.32 per cent. in quantity and an increase of 59 per cent. in value. The average price per ton at furnaces in 1917, as reported to the Survey, was $27.29, compared with $16.96 in 1916, an increase of 61 per cent. The production of pig iron, including ferro-alloys, was 38,647,397 gross tons in 1917, compared with 39,434,797 gross tons in 1916, a decrease of 4.5 per cent., according to figures published by the American Iron and Steel Institute, March 18, 1918.

Jan 12, 1918

The Colorado Scientific Society, Denver, Colo Charles Henderson, President, 519 U. S Custom House, Denver, Colo. Beginning in 1882, up to. about 1919, the Society published 11 volumes containing many valuable papers From the informa¬tion at hand, the papers in those volumes are now only available in libraries or on file at institutions. Vols 12 and 13 are the current volumes, and the list of the geologic papers contained in them are given here For any information as to price and availa¬bility, address the above. Vol 12 (1929-31) No 1, The geology of the Sangre de Cristo Mountains, by J H Johnson, 2, Relation of the ore deposits of the southern Rocky Mountain region to the Colorado Plateau, by B S Butler; 3, Mosquito Range and the Leadville district, by C H Behre, Jr , 4, Geologic history of the Front Range, by T S Lovering, 6, Revision of geologic structure and stratigraphy in the Ouray district, by W S Burbank, 7, Localization of ore in the schists and gneisses of the Mineral Belt of the Front Range, by T. S. Lovering, 8, Relation of the ore deposits of the southern Rocky Mountain region to the Colorado Plateau, by J. B. Tenney; 9, Preliminary geologic map of the Alma mining district, by Q D. Singewald and B S Butler, 10, The Climax molybdenum deposits of Colorado, by B S Butler and J W. Vanderwilt, 12, Localization of ore bodies at Rico and Red Mountain, by G. F Collins, and Geology of Mount Lincoln and Russia mines, by Q D Singewald and B S. Butler. Vol 13 (1932- ): No. 1, Preliminary geologic notes on Galena Mountain, by J. W Vanderwilt, and High plains of Colorado and New Mexico (Late Tertiary history), by F. M. Van Yuyl and J M. Coke

Jan 1, 1933

By P. E. Demmler

PHOSPHORUS combines with copper in various proportions, forming true alloys, some of which are of commercial importance. These materials find wide application as deoxidizers and as a means of introducing phosphorus into other alloys, as in phosphor-bronze. Phosphor-coppers containing 10 and 15 per cent. of phosphorus are the commercial grades that are most generally offered. Each has certain advantages when used in making other alloys. The 10 per cent. grade of phosphor-copper has an advantage over the 15 per cent. in that it has a much lower melting point and can be prepared by certain methods with a much lower loss in phosphorus. The 15 per cent. grade has the advantage of lower freight rates per unit of phosphorus and, by the method to be described, a uniform product can be prepared with practically no loss of phosphorus. Alloys of copper and phosphorus containing any desired percentage of phosphorus lower than 15 per cent. can be prepared by melting together the requisite amounts of copper and 15 per cent. phosphor-copper. Processes for making phosphor-copper may be divided into two classes as follows: (1) Those depending on the smelting of phosphate rock or superphosphate of calcium with copper or copper-bearing materials, and coal or other carbonaceous material; (2) those depending on the direct combination of metallic copper and elemental phosphorus. A number of formulas for preparing phosphor-copper according to the first method have been published. The Metal, Industry' gives-the following: Superphosphate of calcium, 60 lb.; granulated copper, 301b.; finely powdered coal, 10 lb. Similar formulas are given by Brannt2 and others, and detail 'variations are covered by patents, such as those of L A Jeffs3 and H A Webster.4

Jan 8, 1920