Search Documents

By Roland Blanchard

ABSTRACT RECENT discovery at Mount Isa of copper mineralization in commercial amount at a depth of 1000 ft., coinciding with downward termination of ore at about the same depth within the larger silver-lead-zinc lenses that have been the standby of Mount Isa's production to date, has been cited as an example in support of mineral zoning. A previous paper by the author and Graham Hall1 furnished a detailed description of the geology of the ore at Mount Isa as exposed up to that time, but necessarily dealt mainly with the silver-lead-zinc mineralization. Most of the geologic facts that constitute the first half of the present paper were set forth in the previous one in much greater detail, with full supporting evidence for the facts cited. The large amount of underground development (approximately 20 miles) and the extensive exploration carried out by diamond drilling (100,000 ft.) at Mount Isa, added to extensive microscope work conducted over a period of years, both by the company's staff and by others, had made possible the calculation within fairly close limits of mineralogical composition of the principal mineralized block of ground down to 1000-ft. depth, and had established closely the mineral succession, with reasons for deposition of the various minerals in the patterns now occupied by them. The geologic facts as outlined in the previous paper remain as stated; but because substantial development within the new copper ore body and further exploratory diamond drilling within the new silver-lead-zinc area (Race-course) have taken place since that paper was written, statements and figures relating to those two areas in the present paper supersede those furnished in the previous one. The recent work likewise has established more clearly the paragenetic relationship between the chalcopyrite and galena. Evidence confirming the relationship is furnished in the present paper. The facts of ore occurrence at Mount Isa show [ACCEPTED ZONAL SUCCESSION Silver sulphantimonides Galena Sphalerite Tetrahedrite Arsenical sulphides Chalcopyrite Pyrrhotite MOUNT ISA SUCCESSION Chalcopyrite In the main but Silver sulphantimonides wholly Tetrahedriteably not Galenacontemporaneous Pyrrhotite Sphalerite Arsenical sulphides They show further: (I) that instead of the silver-lead minerals yielding to increased zinc in depth, the zinc yields to increased silverlead; (2) no dovetailing of the silver-lead-zinc sulphides into chalcopyrite takes place; (3) despite the large amount of pyrrhotite deposited in the district (estimated at upward of 100,000,000 tons), its deposition took place under moderately low temperature conditions; (4) no evidence has been found for increase in temperature of deposition, with depth, to deepest exploration in ore (1495 ft.). The anomalous condition at Mount Isa, both as to the unorthodox mineral succession and the largely unorthodox pattern of mineral distribution, is explained in the present paper,

Jan 1, 1943

By J. C. McKinnell

The appraisal of an oil lease may often be mad,? through production decline analysis, which requires description of the functional relationship between the oil production rate and either cumulative production or time. Heretofore, attempts to define the function appropriate to a given set of production data have depended to some extent on subjective procedures. The purpose here is to introduce an objective solution, obtained by combining the principle of least squares with the theory of equations. MATHEMATICAL ANALYSIS The fundamental differential equation appropriate to a general class of decline curves may be written. Solution of Eq. 1 for general boundary conditions may be written in terms of either the cumulative oil production or time: These equations constitute the mathematical expression of the so-called hyperbolic decline. Their complete description for a given set of production data requires the numerical evaluation of the three parameters1.', n, D, and (go),. For the special case of n = 0, Eq. 2 becomes q. = (q.), - DiN with the corresponding expression in terms of time being q. = (qa),e...........(5) Similarly, for the special case of n = 1, Eq. 3 becomes with the corresponding expression in terms of cumula- tive oil production being q. = (q.),e " '.......(7) Eqs. 4 and 5 constitute the mathematical description of the so-called exponential decline; Eqs. 6 and 7 are the mathematical description of the harmonic decline.',' Returning to the hyperbolic expressions, Eqs. 2 and 3 may also be written, q: = sNp + b........ (8) and where a = 1 - n; s = (n— 1)D,(q0);"; b = (go):-"; a'=-n;s/= nD,(qo);"; and b' = (go);-. Note that both Eqs. 8 and 9 are linear in either time or cumulative production with respect to an exponential function of the production rate. In other words, a straight line relationship results for both variables when associated with the appropriate power of q,. This fact is of prime importance in the application of statistical analysis. . STATISTICAL ANALYSIS For a given oil lease, the time, production rate and cumulative production are recorded records. To establish predictive formulas from Eqs. 2 and 3, it remains to determine numerical values for the three parameters [n, D, and (q,) .] through an investigation of the past history. Upon interpreting a, s and b as parameters, Eq. 8 may be expressed for every time interval of interest, i, over the past history as follows. (q,): = s(Np), + b........(10) In general, Eq. 10 will not be satisfied exactly, because of the assumptions in the expression of Eq. 1, and the errors and anomalies universally associated with production data. It will instead define the residual, s(Np), + b- CO=d......(11) Squaring both sides and summing over all the data points, m, under consideration yields

By H. C. Fiedler

The solubility of sulfur in Si-Fe was determined by the metallographic examination of heat-treated and quenched samples. In the absence of manganese, the solubility in 3.1 pct Si-Fe was found to be about 0.010 pct at 1000o C, 0.015 pct at 11000C, and 0.020 pct at 1150°C, which is substatntially less than hitherto reported. Increasing the silicon content was found to decrease the solubility of sulfur, which is consistent with the increase in the activity coefficient of sulfur with increasing silicon content that has been reported for Fe-Si alloys. Manganese additions were studied in alloys containing 3.1 pct Si and between 0.013 and 0.015 pct S. At low manganese levels the solubility product of manganese sulfide was found to be lower than previously reported. THE solubility of sulfur in pure polycrystalline iron has been reported by Rosenquist and Dunicz1 and by Turkdogan et al.2 Samples were equilibrated in atmospheres containing different ratios of H2S/H2. Both groups of investigators found a solubility limit in y iron of 0.013 pct at 1000oC and 0.031 pct at 1200°C. In addition, Rosenquist and Dunicz1 found a solubility limit in a iron of 0.020 pct at 900°C. Ainslie, Hoffman, and seybolt3 found significantly higher sulfur contents in polycrystalline iron samples than in single-crystal samples after heating at 890°C in a sealed tube containing a mixture of powdered iron and FeS made with s35. Whereas the single crystals contained 0.013 and 0.016 pct S (± 0.005 pct), the polycrystalline samples contained between 0.016 and 0.026 pct S. Autoradiographs suggested that the excess sulfur in the polycrystalline samples was due to the segregation of sulfur in solution at grain boundaries. Ainslie and seybolt4 have reported on the solubility of sulfur in 3 pct Si-Fe. Their samples were sealed in capsules containing hydrogen and sufficient sulfur as cobalt sulfide to saturate the sample. After heat treating, the sulfur-rich phase on the surface was removed by abrading, and the sulfur content of the sample was taken as the equilibrium value for that temperature. Before the equilibrating heat treatment, the samples were heated to 1300°C to coarsen the grains. The resulting grain size, which was about 3/18 in. in diam, was considered sufficiently large to preclude a sensible increase in sulfur solubility due to grain boundary segregation. They reported the solubility to be 0.029 pct at 900oC, 0.063 pct at 1000oC, 0.076 pct at 1100°C, 0.122 pct at 1200°C, and 0.098 pct at 1300°C.

Jan 1, 1968

By C. S. Roberts

Four binary alloys in this system were creep tested at 300°' to 600°F. A photographic study of microstructural changes showed that the outstanding creep resistance results primarily from a potent precipitation hardening locally at grain boundaries. Twinning was correlated with the primary stage and nonbasal slip with the tertiary stage of creep. THE utility of the rare earth metals as ingredients of magnesium alloys destined for elevated temperature application has been recognized for about 15 years. A review of the early development of these alloys has been given by Leontis. 1,2 It has been only recently that a desire has arisen to understand basically their remarkable creep resistance. The present research had that object. The work of Leontis showed that the differences between the behavior of the individual magnesium-rare earth element binaries was of commercial significance. However, the variations were small compared to the overall difference in creep resistance between the group as a whole and the magnesium alloys of the Al-Zn type. It was decided to conduct this investigation with one binary system which would be representative of the magnesium-rare earth element alloy group. Cerium was chosen as the solute because of its near-middle position in the series and because of its availability in the commercially pure form. A previously published description of the creep behavior of electrolytic magnesium" serves as the background to this research. The experimental approach used in that investigation has been partially repeated here. A series of binary alloys was planned to include the following: 1—A dilute alloy which would contain the cerium almost entirely in solid solution. This would assess the solid solution effect. 2—An alloy which is nearly saturated at the selected solution heat treatment temperature, 1070°F. Here the effect of nearly maximum precip- itation would be obtained without the influence of undissolved Mg-Ce intermetallic. 3—An alloy containing slightly more cerium than is soluble at 1070°F. This would allow the investigation of the effect of a small amount of excess intermetallic. 4—A high cerium alloy in which the influence of a large volume of undissolved intermetallic may be examined. Experimental Details In order to specify compositions of the binary alloy series a knowledge of the solubility of commercially pure cerium in solid electrolytic magnesium and also of the composition of the terminal intermetallic phase was necessary. The latter has been proven to be approximately Mg,Ce by Voge14 and Haughton and Schofield.5 A series of both cast and extruded alloys were solution heat treated 24 hr at 1070°F for a solubility determination. Lineal analyses of the polished and etched microstructures were accomplished with the aid of a Hurlbut

Jan 1, 1955

By Walter Knox, Charles H. Sawyer

All of the coals commonly used in domestic bituminous stokers form coke, and satisfactory operation depends upon the fact that the coke formed is so weakly bound together that it breaks readily in the normal operation of the stoker and automatically maintains a good fuel bed. Some coals, because of their tendency to form solid, blocky coke, are practically excluded from use in small domestic stokers as now built. Other coals, some among the best stoker coals available, can form this troublesome coke under certain conditions. Many contradictory methods have been offered as cures for coke formation. Generally the procedure has been to try various adjustments until a combination was found that seemed to give better results. Such random methods of treatment have not provided any reliable information as to causes. The present paper covers a comprehensive test program undertaken by the Koppers Company's Stoker Coal Research Laboratory at Kearny, N. J. The program had two main objectives; first, to discover what factors affected coke formation, and second; to define corrective steps that could be applied in stoker service work. Conclusions and Results i. The design of the stoker outweighs in importance all other factors capable of improving coke formation. 2. Insufficient air supply aggravates the formation of large blocky coke, although raising the air above 30 to 40 per cent excess (as determined during steady running) does not further improve the character of the coke formed and only reduces its accumulation at the expense of efficiency, increased fly ash, poorer clinker-ing, and other disadvantages. 3. Increasing the coal feed results in a somewhat more friable coke structure and is recommended for persistently troublesome jobs. 4. Increasing over-fire draft improves the character of the coke formed and reduces troublesome accumulations by accelerating off-period burning, although at some expense in efficiency and some increase in fly-ash accumulation. 5. Coke structure was not substantially improved by blocking some of 'the retort tuyeres, although the blocking of tuyeres at the feed-screw end of a rectangular retort did lead to somewhat improved performance, possibly because of considerably better distribution of coke in the fuel bed. 6. With the equipment tested no difference was shown between installation of the same stoker in a steam boiler and a warm-air furnace, or between a sand-filled and a ventilated type of hearth. 7. The following design features had no noticeable effect on coke formation: a. Presence or absence of coal-tube air as provided by many manufacturers to eliminate smoke-back. B. Presence or absence of a flap damper ill the air duct to minimize off-period burning. c. Continuous or intermittent (ratchet and pawl driven) movement of fuel feed screw.

Jan 1, 1944

By Charles H. Sawyer, Walter Knox

All of the coals commonly used in domestic bituminous stokers form coke, and satisfactory operation depends upon the fact that the coke formed is so weakly bound together that it breaks readily in the normal operation of the stoker and automatically maintains a good fuel bed. Some coals, because of their tendency to form solid, blocky coke, are practically excluded from use in small domestic stokers as now built. Other coals, some among the best stoker coals available, can form this troublesome coke under certain conditions. Many contradictory methods have been offered as cures for coke formation. Generally the procedure has been to try various adjustments until a combination was found that seemed to give better results. Such random methods of treatment have not provided any reliable information as to causes. The present paper covers a comprehensive test program undertaken by the Koppers Company's Stoker Coal Research Laboratory at Kearny, N. J. The program had two main objectives; first, to discover what factors affected coke formation, and second; to define corrective steps that could be applied in stoker service work. Conclusions and Results i. The design of the stoker outweighs in importance all other factors capable of improving coke formation. 2. Insufficient air supply aggravates the formation of large blocky coke, although raising the air above 30 to 40 per cent excess (as determined during steady running) does not further improve the character of the coke formed and only reduces its accumulation at the expense of efficiency, increased fly ash, poorer clinker-ing, and other disadvantages. 3. Increasing the coal feed results in a somewhat more friable coke structure and is recommended for persistently troublesome jobs. 4. Increasing over-fire draft improves the character of the coke formed and reduces troublesome accumulations by accelerating off-period burning, although at some expense in efficiency and some increase in fly-ash accumulation. 5. Coke structure was not substantially improved by blocking some of 'the retort tuyeres, although the blocking of tuyeres at the feed-screw end of a rectangular retort did lead to somewhat improved performance, possibly because of considerably better distribution of coke in the fuel bed. 6. With the equipment tested no difference was shown between installation of the same stoker in a steam boiler and a warm-air furnace, or between a sand-filled and a ventilated type of hearth. 7. The following design features had no noticeable effect on coke formation: a. Presence or absence of coal-tube air as provided by many manufacturers to eliminate smoke-back. B. Presence or absence of a flap damper ill the air duct to minimize off-period burning. c. Continuous or intermittent (ratchet and pawl driven) movement of fuel feed screw.

Jan 1, 1944

By W. C. Ellis, M. E. Fine

In the iron-cobalt system there are several property-composition relationships of theoretical importance. The alloys are ferromagnetic exhibiting a maximum saturation at approximately 33 at. pct cobalt;' the interatomic distances at room temperature show large positive deviations from Vegard's rule;2 and in the region of 50 at. pct cobalt there is an order-disorder transition2 which has a large effect on other properties. The thermal expansion data for the system have been reported only from room temperature to 100 C and for this temperature range a minimum in coefticient in the rcgion of 50 at. pct cobalt is well established.3,4,6 This paper reports the expansion properties in the iron-cobalt system for temperatures from 30 to 850°C, shows the correlation with other physical properties, and proposes an explanation for the tcrrelation. Experimental Procedure The thermal expansivities of iron-cobalt alloys in 10 pct steps in composition were determined from 30 to about 850°C. The major series of alloys was prepared by induction melting from Armco iron and cobalt rondelles with the addition of about 0.6 wt pct manganese. This series was supplemented by three compositions: high purity electrolytic iron, high purity electrolytic cobalt, and an alloy of 52.1 wt pct cobalt prepared from the high purity electrolytic iron and electrolytic cobalt by vacuum-melting. The compositions of both series of alloys are given in Table I. The specimens for measurement were prepared from the cast ingots by first hot-swaging followed in most instances by cold-swaging to 0.180-in. diam rod. Some alloys in the region of 5c pct cobalt, because of inherent cold-brittleness, were swaged hot to the final diameter. The expansion specimens were approximately 2 1/2 in. long with flat-ground and polished ends. Before measurement they were annealed in hydrogen for I hr at 900°C. In the apparatus used for the thermal expansivity measurements (Fig I), a modification of that designed by Hidnert and Sweeney,? the differential expausion between the specimen and vitreous silica was measured by a dial micrometer reading to 0.001 mm. An invar fixture supported the dial gauge, and this fixture, in turn, was connected to a split invar collar which supported the outer silica tube. A pyrex "T" was placed over the outcr silica tube and was sealed to the invar collar by Apiezon Q sealing compound. A movable hollow vitreous silica rod which rested on top of the test specimen slid through a flexible rubber diaphragm cemented to the top of the pyrex "T." The specimen rested On a vitreous silica pedestal fused into the outer tube and was kept centered by a silica sleeve. A nonoxidizing atmosphere was obtained by admitting hydrogen into the

Jan 1, 1949

By H. J. R. Way

The work to be described was undertaken at various periods from 1937 to 1939 on the Busia gold field, in the eastern province of Uganda. It was decided to examine the possibility of reef prospection by the resistivity method, for it was not known how far the usually disintegrated nature of most reefs in the ubiquitous laterite near the surface would obscure indications obtained by resistivity traverses. The work at the commencement was therefore largely experimental, but the results obtained thereby were satisfactory, and a survey was started at the Government closed area at Amonikakine. With the limited time and resources at the writer's disposal, it was not possible to complete the survey to his satisfaction or to follow up exhaustively all the geophysical indications, but some of the results of the experimental work and the survey were of sufficient interest to be worth recording; in particular the relation between the width of reef, electrode separation and shape of the curve, and the interference effect of constant separation curves over zones of float are significant and useful. Three new veins were located, but only one contained sufficient gold to warrant detailed prospection. This was called the Geophysical reef, and was uncovered over a strike distance of 1140 ft., and there are indications that it extends over a distance of 1990 ft. These results and the recom- mendations consequent therefrom were embodied in a special report to the Uganda Geological Survey. History OF the Field The Busia field is in the southeastern corner of Uganda near the Kenya-Uganda border, and is about 17 miles north of the northeastern corner of Lake Victoria. Gold was first discovered in the area in the stream beds by Davies1,2 in 1932. Subsequently numerous small alluvial claims were worked by prospectors and the area was prospected for reef by a company for periods varying from three to nine months, but was finally abandoned, as the results were considered unfavorable. Further prospecting by the Geological Survey in 1935-1936 under Davies8 and later under the writer4 uncovered three reefs with sufficient gold values to be of economic interest. These were finally taken over by a company known as Borderland Syndicate, which still owns the area, and from September 1937 to the end of 1941 about 13,000 oz. of gold was extracted from reefs of the area proved by the Geological Survey. Opencast mining operations are still proceeding (February 1943). The Amonikakine area lies to the immediate north of that of Borderland Syndicate. A certain amount of prospecting had been done when the writer started work there. As a result of his report, this area was taken over by another syndicate, but little further work was accomplished before it ceased operating because of difficulties of wartime working.

Jan 1, 1946

By H. J. R. Way

The work to be described was undertaken at various periods from 1937 to 1939 on the Busia gold field, in the eastern province of Uganda. It was decided to examine the possibility of reef prospection by the resistivity method, for it was not known how far the usually disintegrated nature of most reefs in the ubiquitous laterite near the surface would obscure indications obtained by resistivity traverses. The work at the commencement was therefore largely experimental, but the results obtained thereby were satisfactory, and a survey was started at the Government closed area at Amonikakine. With the limited time and resources at the writer's disposal, it was not possible to complete the survey to his satisfaction or to follow up exhaustively all the geophysical indications, but some of the results of the experimental work and the survey were of sufficient interest to be worth recording; in particular the relation between the width of reef, electrode separation and shape of the curve, and the interference effect of constant separation curves over zones of float are significant and useful. Three new veins were located, but only one contained sufficient gold to warrant detailed prospection. This was called the Geophysical reef, and was uncovered over a strike distance of 1140 ft., and there are indications that it extends over a distance of 1990 ft. These results and the recom- mendations consequent therefrom were embodied in a special report to the Uganda Geological Survey. History OF the Field The Busia field is in the southeastern corner of Uganda near the Kenya-Uganda border, and is about 17 miles north of the northeastern corner of Lake Victoria. Gold was first discovered in the area in the stream beds by Davies1,2 in 1932. Subsequently numerous small alluvial claims were worked by prospectors and the area was prospected for reef by a company for periods varying from three to nine months, but was finally abandoned, as the results were considered unfavorable. Further prospecting by the Geological Survey in 1935-1936 under Davies8 and later under the writer4 uncovered three reefs with sufficient gold values to be of economic interest. These were finally taken over by a company known as Borderland Syndicate, which still owns the area, and from September 1937 to the end of 1941 about 13,000 oz. of gold was extracted from reefs of the area proved by the Geological Survey. Opencast mining operations are still proceeding (February 1943). The Amonikakine area lies to the immediate north of that of Borderland Syndicate. A certain amount of prospecting had been done when the writer started work there. As a result of his report, this area was taken over by another syndicate, but little further work was accomplished before it ceased operating because of difficulties of wartime working.

Jan 1, 1946

By R. K. McGeary, B. Lustman

Orientation relationships and rates of annealing of 97 pct cold rolled zirconium have been studied by X-ray techniques, metallography, and by hardness measurements. The process of annealing occurring by the formation of domains, and their subsequent growth without recrystallization, is demonstrated. NUMEROUS investigators1-' have revealed sub-grain formation after annealing cold worked metal single crystals and have generally described the results in terms of a dislocation mechanism of polygonization.5,6 in heavily cold rolled polycrystal-line aluminum the first stages of heating cause an apparently spontaneous subdivision of regions of the deformed matrix into a great number of slightly disoriented domains followed or accompanied by rapid growth of certain domains to form a recrystallization texture.7,8 In the present investigation the isothermal rate of annealing of cold worked polycrystalline zirconium has been studied by X-ray techniques, metallography, and by hardness measurement. It will be shown that, rather than by the usual nucleation and growth mechanism,"12 the process of annealing can best be explained by the formation of domains early in the annealing treatment and the subsequent growth of these domains without recrystallization. Experimental Procedure All the experimental work was performed on an arc-melted ingot of high purity zirconium crystal bar made by Westinghouse in a production scale deBoer unit. The weight percentage of impurities in the zirconium were as follows: C, 0.04; Fe, 0.05; Hf, 0.014; W, 0.01; Ti, Ni, and Al, 0.003; Si and N, 0.002; Cr and Cu, 0.001. Metallographically the zirconium showed only a single phase. The 4 in. diarn ingot was forged at 760°C to a 1 1/2x3 in. plate and was then rolled at 760°C to 0.150 in. thickness and annealed at this temperature for 20 min to produce an equiaxed grain structure of about 0.1 mm average grain diameter. The hot rolled plate was roller-leveled, surface ground to 0.135 in., cold rolled 83 pct reduction in thickness on a two-high mill, and then to a total reduction of 97 pct on a Sendzimir mill. The 0.004 in. strip material so produced received no subsequent mechanical treatment. Specimens % in. square were sheared from the rolled strip and isothermally annealed at 104 mm Hg in an all glass vacuum system equipped with a Vycor furnace tube. The temperature data presented are the average temperatures during the runs and did not vary more than about k3"C. X-ray Diffraction Methods: When zirconium is drastically cold rolled, a high degree of preferred orientation results in which prism poles, {1010}, are perpendicular to the rolling direction. After fully annealing this material an entirely new texture develops which corresponds to a 20" or 40" rotation of the deformation texture about hexagonal axes of

Jan 1, 1954

By H. E. Stauss

THE time-to-fracture test has been applied to pure platinum and to two alloys of platinum under the special conditions of small cross-sectional area of the specimens and of a test temperature above the annealing temperature. While the results are similar in character to those secured with large specimens of steel at temperatures below the annealing temperatures, two differences are noted: (I) an upward inflection in the curves for log stress vs. log time for the alloys, and (2) a sharp break in the curve for log stress vs. log time for pure platinum when single crystals filled the wire. The experiments showed that: (I) platinum and 10 per cent rhodium-platinum maintained their strengths at 1100°C. better than did 10 per cent iridium- platinum, and (2) the rhodium-platinum after a time exceeded the iridium-platinum in strength at 1100°C. Platinum alloys in their service at high temperatures encounter conditions some- what similar to those that exist in the usual form of the time-to-fracture "l test with steel. This paper is intended primarily to present results obtained by a "time-to- fracture" test under conditions approximating actual service for platinum (at the temperature 1100°C. under oxidizing conditions) with three materials, pure platinum (99.99 per cent), a platinum alloy with lo per cent iridium, and a platinum alloy with 10 per cent rhodium. The experimental procedure differed from that previously used in this type of measurement in that the samples were of small diameter (0.010 in.), were fully annealed, and were tested at a temperature definitely above their annealing points (600°C., 1000°C. and 1050°C., respectively, for 60 per cent cold reduction and 15 min. heating time2,3). The experimental arrangement was similar to that previously described,4 using as heating unit a small, horizontal, platinum- wound furnace, ½ by 12 in., maintained at constant temperature by an automatic controller. The samples were 0.010-in. wires, which had been annealed at 1200°C. by drawing them slowly through the furnace. The time-to-fracture was measured electrically. Elongation was not determined because of the difficulties inherent in the experimental arrangement. Life-that is, the time-to-fracture-was considered the important property in these first tests. No attempt was made to measure the reduction in area, but the types of fracture were noted qualitatively; in the text they are referred to as (I) the normal, plastic, or necked fracture, (2) the knife-edge fracture, and (3) the brittle or intercrystalline fracture with small reduction of area. Results for different constant applied stresses are plotted in Fig. I. In all cases at least two trials were made for each stress, although they cannot always be indicated separately on the curves. The breaking stresses drop very rapidly to a small frac-

Jan 1, 1943

By H. B. Smith, B. Egererg

In a previous paper1 the authors dealt with the physical properties of cold-rolled and heat-treated Britannia metal of the approximate composition Sn, 91 per cent., Sb, 7 per cent. and Cu, 2 per cent. It was found that cold rolling to more than 50 per cent. reduction produced a continuous softening of the metal when measured by the Brinell machine, whereas the Shore instrument indicated increased hardness; that the strength of the material followed the Brinell hardness and that the metal therefore became weaker the more it was cold-rolled; and further, it was found that hardness and strength could be largely restored to the cold-rolled metal by "baking" for about one hour at any temperature between 200" and 450" F., the melting point. The higher the baking temperature, the more effective was the heat treatment as far as increased hardness was concerned. It seemed to be of little importance whether the metal was soaked or not at the baking temperature for a great length of time and the rate of cooling seemed to be immaterial. The present paper deals with the same alloy and more particularly with the resistance towards various forms of stress — tensile, bend and deep drawing. The metallography of Britannia metal has in part also been covered and an explanation attempted for the abnormal behavior of this alloy. Tensile and Bend Tests Two ingots 73/4 in. wide, 11 in. long and ¾ in. thick were cast from the same pot. One ingot was cold-rolled in one direction to a strip 0.241 in. thick, which furnished the tensile test specimens; the other ingot was rolled in the same way to 0.253 in. and furnished the specimens for the bend tests. The ingots were cast as described in the previous paper and cold-rolled in six passes.

Jan 1, 1930

By M. G. Benz, J. F. Elliott

Otto Schaaber (Institut für Harterei-Technik, Bremen -Schönebeck, Germany)— Langenberg, Pestel, and Honeycutt gave an interesting example of the grain refining effect nonstationary magnetic fields may execute on a solidifying metal. Probably some additional comments, based on more than a decade of experience with this method of influencing crystallization, may be useful. They refer to an attempt to explain the mechanism of grain refinement by such fields, and to recent European developments which have not been mentioned in the paper. I. During studies of the temperature distribution in a metal body near the phase boundary solid/liquid, an anomaly was observed under certain special conditions: a) direction of heat transfer as horizontal as possible, b) steady state (equilibrium, i.e,, solidification resp. melting rate exactly zero). In the liquid phase, immediately adjacent to the phase boundary, the temperature was found to be constant over an appreciable distance in spite of a high value of heat transfer (40.000 to 70.000 keal/ m2h).3 Convection, which might explain this phenomenon, could not be observed. Therefore another explanation had to be sought. The assumption that a metallic melt, especially at temperatures near the point of solidification, contains some sort of atomic arrangement with a higher degree of order than the surrounding liquid, now is generally accepted. Considering the differences in energy between such an arrangement and its environs, a transport of heat even in absence of any temperature gradient is conceivable by continued formation and redissolution of regions with a higher degree of order, i.e., with lower energy level.3 At this stage, it was not necessary to postulate any special condition as to the form or size of these regions or the distance between arrangements to be newly formed and those to be redissolved. However, a simple consideration shows that an energy transfer from one region to another will only be possible without loss of energy, if the distance between will be equal to the lattice parameters, and if, secondly, crystallographic axis or planes will be parallel.4 By the way, this assumption might give a reasonable explanation of the well known orientation effect of the heat flow during solidification. Any measures to prevent columnar crystallization should act upon this ordering mechanism: a) the regions with a lower energy (higher order) should not be allowed to arrange themselves parallel to the direction of heat flow, and their growth should be disturbed; b) all conditions leading to an appreciable heat flow of uniform direction should be avoided or removed. Condition a) may be satisfied by a physical force preferably under 90 deg to the main axis of the columnar crystals (i.e., parallel to the solidification front) acting on the ordered regions; condition b) by equalizing any differences in

Jan 1, 1962

By E. J. Dulis, G. V. Smith

AS reported several years ago,' nitrogen may be taken up from the atmosphere by austenitic Cr-Ni steels during creep or creep-rupture tests. This was indicated by chemical analysis and by the appearance of a new microstructural phase, or phases, tentatively identified as chromium nitride (S), at the surface or at the intergranular cracks associated with fracture. The nitrogen pickup was observed to be dependent on time, temperature, and deformation. In a more recent investigation, a sample was obtained in which there was sufficient of the precipitate to suggest that it could be readily identified by X-ray diffraction. This sample had been taken from a 1/4 in. diam creep-rupture specimen of annealed, type 304L stainless steel of the following initial composition: C, 0.03 pct; Mn, 0.65; P, 0.010; S, 0.019; Si, 0.54; Cr, 19.50; Ni, 12.02; N, 0.031; and Al, 0.005. The specimen had ruptured after 10,470 hr at 1500°F (2000 psi). In this case nitrides were distributed across the whole section of the sample, Fig. 1. The precipitate occurred both at the grain boundaries and within the grains; the latter precipitate had in some cases the appearance of pearl-ite, and in others was distinctly Widmanstatten. Chemical analysis of the sample after test showed 0.64 pct "soluble" nitrogen (soluble in 1:1 hydrochloric acid: water) and 0.18 pct "insoluble7' nitrogen (insoluble in the hydrochloric acid solution but dissolved by fuming sulphuric acid). For identification of the precipitate by X-ray diffraction, the matrix in the surface layer of the specimen was dissolved by prolonged attack in an alcoholic solution of picric and hydrochloric acids. The appearance of the specimen surface after such etching is shown in Fig. 1c. The diffraction pattern of the surface-concentrated precipitate was obtained with a recording spectrometer in both the forward and back-reflection regions (the latter by adapting a special fixture to the conventional X-ray unit). The observed X-ray diffraction lines, Table I, show the presence of Cr,N and CrN; the agreement with interplanar spacings calculated from reported data2,3 is quite good. Since it has been suggested' that CrN dissolves only in concentrated sulphuric acid, whereas Cr2N dissolves in dilute hydrochloric or sulphuric acids, an effort was made to distinguish between the two nitrides. This proved possible, inasmuch as etching in a dilute solution of hydrochloric acid gave a sample in which microscopic examination showed that much of the Widmanstatten-pearlitic precipitate within the grains had been eaten out, leaving the grain boundary precipitate in relief, and which, when examined by X-ray diffrac-

Jan 1, 1953

By R. P. Smith

The carbon content of a number of alloys ranging (before carburitation) from purified iron to purified cobalt was determined for fixed activities of carbon by equilibration with each of six CO-CO2 atmosphere at 1000°C. At fixed carbon activity, the carbon content decreases continuously with increasing cobalt content. For concentrations of 0 to 50 at. pct Co the results can be expressed by a linear interaction equation of the type In y2 = 7.76n2/(n1+n3)+ 2.30 n3/(n1+n3) where y2 is the activity coefficient of carbon (standard state such that y2— 1 as n2 — 0 in the Fe-C binary) and n1, n2, and n3 are the number of atoms of iron, carbon, and cobalt per unit weight of alloy. The results are also given in terms of the a functions. In the same concentration range, the results are in accord with the regular solution theory of Alcock and Richardson. THE carbon content of Fe-Si, Fe-Mn, and Fe-Ni alloys at fixed activities of carbon has been reported previously.'-, The present work extends R. P. SMITH, Member AIME, is Research Chemist, E. C. Bain Laboratory for Fundamental Research, United States Steel Corp., Research Center, Monroeville, Pa. these measurements to a series of Fe-Co alloys. These alloys, like the Fe-Ni alloys, are fcc ("aus-tenitic") over the entire range of composition at 1000°C. EXPERIMENTAL PROCEDURE The alloys were made from electrolytic cobalt and Plast-Iron in a small vacuum-melting furnace. A small amount of graphite was added to each melt to keep the oxygen content low. The ingots were analyzed for iron and carbon: the amount of cobalt was obtained by difference. Analysis of the top and bottom of the ingots indicated that they were uniform in alloy content. Except for the pure cobalt the ingots were hot-rolled to approximately 0.15 cm thickness, cleaned by sandblasting, then cold-rolled to about 0.045 cm. We were not successful in cold rolling the pure cobalt; therefore it was hot-rolled to the final thickness. The last traces of surface oxide were removed by acid pickel, then the samples were treated in a hydrogen-2 pct water vapor mixture at 1100°C to remove carbon and most of the oxygen. The carburizing procedure was similar to that previously described.1,2,4 The alloys in the form of strips about 1.7 cm wide, 7.5 cm long, and 0.04 cm thick, together with a similar specimen of purified iron, were equilibrated with each of six CO-CO2 mixtures of fixed composition, then quenched in the

Jan 1, 1965

By Don B. Carson, Donald L. Katz

NATURAL gases under pressure form crystal-line hydrates with water. Experimental data are reported on four-phase equilibrium for the methane-propane-water, methane-pentane-water, and methane-hexane-water systems. Temperatures and pressures for equilibrium between gas, water-rich liquid, hydrocarbonrich liquid, and hydrate were measured, as well as the percentages of methane and propane in the hydrate. The data indicate that natural gas hydrate behaves as a solid solution and that pentanes and heavier hydrocarbons do not enter into the solid phase. Vapor-solid equilibrium constants are presented that permit the approximation of the conditions for hydrate formation, from the composition of a gas. INTRODUCTION Natural gas hydrates have been the object of considerable research in recent years, because of the trouble they have caused in the natural-gas and natural gasoline industries. Natural gas hydrates are white crystalline compounds of water and gas, which, under pressure, exist at temperatures considerably above the freezing point of water. Because of the relatively high temperatures at which the hydrates exist, they become a nuisance in high-pressure gas operations where water is present, since their formation causes partial or complete plugging of valves and pipes. From a practical standpoint, the trouble incident to hydrate formation has been solved by dehydration of the gas before it enters the plant or pipe line, or by other remedial measures. Extensive work on gas hydrates in the latter part of the nineteenth century, by Villard1 and others, gave data on methane hydrate and on ethane hydrate. Schroeder summarized these theoretical studies.2 Hammerschmidt3 introduced the information on gas hydrates to the gas industry and Deaton and Frost4-6 gathered a considerable number of data on the behavior of natural gas hydrates. Recent papers7,8 have extended both the data and the theory of these hydrates. At present, data are available on temperatures and pressures of hydrate formation for pure methane, ethane, propane, n-butane, methane-ethane mixtures, methane-propane mixtures, methane-butane mixtures, and some 15 natural gases, all in the presence of excess water. However, up to the present time no method has been available for predicting the temperature at given pressures or the pressure at given temperatures at which natural gases will form hydrates if saturated with water. This paper pre¬sents data on the methane-propane-water, methane-pentane-water and methane-hexane water systems in four phases, one of which is the hydrate. The application of the phase rule to the methane-propane-water data proves that hydrates behave as solid solutions. The data of this paper and those in the literature were used to develop vapor-solid equilibrium constants,8 which permit prediction of conditions of hydrate formation from the analysis of a natural gas.

Jan 1, 1941

By C. Richard Honeycutt, Frederick C. Langenberg, Guenter Pestel

Otto Schaaber (Institut für Harterei-Technik, Bremen-Schönebeck, Germany)— Langenberg, Pestel, and Honeycutt gave an interesting example of the grain refining effect nonstationary magnetic fields may execute on a solidifying metal. Probably some additional comments, based on more than a decade of experience with this method of influencing crystallization, may be useful. They refer to an attempt to explain the mechanism of grain refinement by such fields, and to recent European developments which have not been mentioned in the paper. I. During studies of the temperature distribution in a metal body near the phase boundary solid/liquid, an anomaly was observed under certain special conditions: a) direction of heat transfer as horizontal as possible, b) steady state (equilibrium, i.e,, solidification resp. melting rate exactly zero). In the liquid phase, immediately adjacent to the phase boundary, the temperature was found to be constant over an appreciable distance in spite of a high value of heat transfer (40.000 to 70.000 keal/ m2h).3 Convection, which might explain this phenomenon, could not be observed. Therefore another explanation had to be sought. The assumption that a metallic melt, especially at temperatures near the point of solidification, contains some sort of atomic arrangement with a higher degree of order than the surrounding liquid, now is generally accepted. Considering the differences in energy between such an arrangement and its environs, a transport of heat even in absence of any temperature gradient is conceivable by continued formation and redissolution of regions with a higher degree of order, i.e., with lower energy level.3 At this stage, it was not necessary to postulate any special condition as to the form or size of these regions or the distance between arrangements to be newly formed and those to be redissolved. However, a simple consideration shows that an energy transfer from one region to another will only be possible without loss of energy, if the distance between will be equal to the lattice parameters, and if, secondly, crystallographic axis or planes will be parallel.4 By the way, this assumption might give a reasonable explanation of the well known orientation effect of the heat flow during solidification. Any measures to prevent columnar crystallization should act upon this ordering mechanism: a) the regions with a lower energy (higher order) should not be allowed to arrange themselves parallel to the direction of heat flow, and their growth should be disturbed; b) all conditions leading to an appreciable heat flow of uniform direction should be avoided or removed. Condition a) may be satisfied by a physical force preferably under 90 deg to the main axis of the columnar crystals (i.e., parallel to the solidification front) acting on the ordered regions; condition b) by equalizing any differences in

Jan 1, 1962

By T. E. Davidson, A. P. Lee

It is known from the early work of Bridgman that the two lowest-pressure transitions (I-II and II-III) are accompanied by substantial and abrupt changes in resistivity and Volume. However, unlike the temperature -induced allotropic transformations observed in such elements as lithium, cobalt, tin, and so forth, there is little actually known about many of the characteristics of the pressure-in&ced transitions. This current work involves an examination of the structural and transformation characteristics of the bismuth I-II and II-III transitions under hydrostatic pressures. The relationship of initial structure to the transformation pressure, rate, resistivity change, and resultant structure is discussed. It is shown that the transition pressure and transformation rate are independent of the presence of grain boundaries and associated anisotropy-induced deformation. An observed hysteresis in both the I-II and II-III transitions is shown. BISMUTH is one of the most interesting of the elements exhibiting pressure-induced polymorphs since it undergoes several allotropic transformations at pressures below 90,000 atm. It is known from the early work of bridman1,2 that the two lowest-pressure transitions (1-11 and 11-111) are accompanied by substantial and abrupt changes in resistance and volume. However, unlike the temperature-induced allotropic transformations observed in such elements as lithium, cobalt, tin, and so forth, there is little actually known about many of the characteristics of these pressure-induced transitions. It is the purpose of this work to examine some of the structural and transformation characteristics of the bismuth 1-11 and 11-111 transitions under hydrostatic pressures. Another interesting characteristic of bismuth is that, in its polycrystalline form, hydrostatic pressures of sufficient magnitude will induce severe progressive plastic deformation in the region of the grain boundaries.3 This deformation, which has also been observed in several other metals, is attributed to the high degree of anisotropy in the linear compressibility of bismuth, resulting in shear stresses in the grain boundaries when it is exposed to hydrostatic pressure. Most thermally induced allotropic transformations in metals, whether of the diffusionless ather-ma1 (martensitic) or isothermal nucleation and growth types, are dependent upon structure and prior history,4 viz., grain boundaries, deformation, and so forth. One logically wonders then whether the transformation characteristics of the pressure-induced polymorphs in bismuth might also depend upon initial structure, particularly with respect to the presence of grain boundaries and associated plastic deformation. In this investigation, the role of grain boundaries and plastic deformation on the characteristics of the bismuth I-II and 11-111 transitions will be established. The rather unique residual microstruc-tural changes associated with these transitions will be presented and discussed. The occurrence of a measurable hysteresis in both the I-II and 11-111 transitions will be demonstrated. The type of transformation mechanism based on the observed transformation rate will be discussed. EXPERIMENTAL PROCEDURE A) Apparatus. The hydrostatic pressure system utilized in this investigation is similar to that previously reported by Bridgman' and Birch and Robertson,5 and has been previously described.3 For the purpose of this work, the pressure medium utilized was a 1:l mixture of pentane and isopentane. Pressure measurement was by means of a manganin coil in conjunction with a Foxboro Recorder. The manganin coil was mounted in the bottom closure and inserted inside the pressure cavity. Based on calibration against a controlled clearance piston gage at approximately 10,000 atm, the estimated error in the pressure measurement was +2 pct. Assuming the nonlinearity in the pressure coefficient of resistivity between 10,000 and 28,000 atm to be not greater than 1 pct, then the estimated error in the range of the I-II and 11-111 transitions was +3 pct. B) specimen Material and Preparation. The bismuth utilized throughout this investigation was of

Jan 1, 1964

By T. F. Mueller, P. A. Witherspoon

For the case of an infinite radial system operating at constant terminal rate, the reservoir engineer often uses the "point source" solution of the diffiusivity equation to study pressure interference effects. At early times and at short distances from the inner boundary these solutions are invalid. The amount of error is often not precisely defined because of mathematical difficulties. Work presented here shows that, if dimensionless time is defined appropriately, previous solutions of the pressure equation can be displayed .as a family of curves on one chart. These solutions include the point source solution (referred to in the field of hydrology as the Theis solution) and other solutions obtained with digital computer methods. With these curves, an exact evaluation of the pressure drop within a reservoir or an aquifer can be made by the engineer. Examples of field problem solutions are presented. In most reservoirs the error involved when the Theis solution is employed is often negligible; whereas, in the calculation of interference effects in an aquifer, a substantial error can occur through such an approach. INTRODUCTION Flow equations are used in petroleum engineering to study the behavior of individual wells and reservoirs. In the case of wells, the pressure response at the wellbore face is the major point of interest; whereas, in the case of reservoirs, the pressure response at the interface of the aquifer boundary is sought. To aid in such studies, the flow equations have been solved in terms of the behavior at these two inner boundaries. Only limited work has been published in regard to the pressure conditions away from these points, i.e., within the reservoir or aquifer. Theis and Mortada are among the few who have reported on this problem. The Theis approach employs the exponential integral and is valid for pressure conditions that occur some distance away from the flow disturbance. It is derived from the concept of a point source, as opposed to a flow across some finite area. The Mortada results, on the other hand, are valid at all points within the reservoir or aquifer. They are presented in terms of dimension less ratios of the radius where the pressure is desired to the radius where the flow rate is measured. Their main use, in the past, has been in aquifer studies. The published results are presented in the form of graphs that are limited to a maximum radius ratio of 64. These graphical results are cumbersome to interpolate at non-integral radius ratios, so that one may be forced to utilize a rather involved analytical expression presented by Mortada. BASIC EQUATIONS The solutions of Mortada and Theis are both based on the diffusivity equation as applied to the case of an infinite radial system subject to a constant terminal rate. The equation is obtained by combining the material balance equation with Darcy's flow equation. The assumptions implicit in the use of this equation are as follows: (1) a single fluid is present that occupies the entire pore volume; (2) the reservoir is horizontal, homogeneous, uniform in thickness, and of infinite radial extent; (3) compressibility and viscosity of the fluid remain constant at all pressures; and (4) fluid density obeys the equation Using the diffusivity equation in situations where the above conditions do not hold will result in errors. These errors (not discussed here) but only the errors which arise in the solution of the equation itself. The diffusivity equation for the homogeneous reservoir conditions cited above can be written in cylindrical coordinates, as To obtain a dimensionless equation, so a single solution can be used for applications of different porosity, permeability and fluid properties, the following transformations are usually made: After these transformations are made, Eq. 3 .can be written in dimensionless form, as MORTADA SOLUTION One solution of Eq. 6 has been given by Mortada.

Jan 1, 1966

By R. N. Dokken, J. F. Elliott

A high-temperature solution calorimeter was used to measure directly the partial molar heat of mixing of nickel in the Cu-Ni system, 0 to 15 at. pct Ni and 1200°C; of silver in the Cu-Ag system, 0 to 50 at. pct Ag and 1100°C; and of cobalt in the Cu-Co system, 0 to 6 at. pct Co and 1200°C. The heats of fusion of copper and silver were also detervnined directly. The results of these investigations are as follows: Cu-Ni: HM = [2.64 + 0.25Xm JXNiXCy kcal/g-U~OI Cu-Ag: HM =[4.00 + 0.31XAglXAgXCu kcal/g-atom Cu-Co: HF~ = [8- 5X~,]X& kcal/g-atotn Cu, AH, = 3290 * 275 cal/g-atom Ag, AH, = 2890 * 250 cal/g-atom The performance of the calorimeter was enhanced by improving the operational and control procedures, particularly the temperature-wieasuren~ent method and the solute-addition practice. The interpretation of the experimental data was improved by developing machine computational techniques that increased the speed, flexibility, and accuracy of the treatment of the data. THIS paper reports further measurements of the heats of solution of liquid metals with the high-tem- perature solution ca1orimeter.l Measurements were made of the partial molar heats of mixing in the following liquid alloys: Cu-Ni, Cu-Ag, and Cu-Co. In addition the heats of fusion of copper and silver were also determined. The apparatus and the experimental procedure were essentially those of Benz and Elliott.2 Several modifications in the experimental method and the means for interpreting the data were incorporated in this study to improve the results. The operation of the calorimeter and its characteristics will be described only briefly here. The

Jan 1, 1965