Search Documents

By W. B. Gogarty, H. R. Bailey

Methods are presented for determining molecular diffusion coefficients by using data from, capillary flow experiments. These methods are based on a numerical solution (presented in a previous paper) of the partial differential equation describing the combined mechanisms of flow and diffusion. Results from this numerical solution are given and compared with the approximate analytical solution of G. I. Taylor. The numerical solution is valid over a much larger time range. These methods are applied to experimental results for the fluid pairs water-potassium permanganate solution and amyl acetate-orthoxylene. Both of these fluid pairs have approximately equal densities and viscosities. Graphical and numerical techniques are presented for deter mining diffusion coefficients from the flow data. Values obtained by these techniques are compared with values obtained by other methods. INTRODUCTION The molecular diffusion coefficient is known to be a variable in determining the amount of mixing in a miscible displacement process. The effect of molecular diffusion on dispersion in longitudinal flow through porous media -has been examined by different investigators. These investigators concluded that at low velocities of flow, the amount of dispersion is approximate1y proportional to the molecular diffusion coefficient. The influence of diffusion on fingering, channeling, and overriding has been mentioned by other investigators.4 Recent studies5,6 have been made on the effects of molecular diffusion in connection with the problem of gravity segregation. Many different methods have been developed for the experimental determination of molecular diffusion coefficients? These methods differ mainly according to boundary conditions selected and analytical procedures used. Nevertheless, all of these methods have the condition in common that the bulk fluids in which diffusion is occurring are stationary with respect to each other. In connection with a series of papers on mixing in capillary flow,8-10 Taylor suggested the use of a flow method for determining molecular diffusion coefficients. Additional studies 11-13 have been conducted on miscible displacements in capillary tubes, but the data from these studies were not used for the specific purpose of determining diffusion coefficients. The flow method proposed by Taylor results in a single value of the diffusion coefficient for the fluid pair used in the displacement experiments. This single value represents the true value for the fluid pair when the diffusion coefficient is independent of concentration. If the diffusion coefficient is a function of concentration, the single value obtained by the flow method gives an average value for the coefficient of the fluid pair. These average values are based on diffusion taking place over the entire range of concentration, i.e., from 0 per cent of one fluid to 100 per cent of that same fluid. In field applications of the miscible displacement process, gradients occur over the same range of concentration as are found in the displacements in capillary tubes. Molecular diffusion coefficients obtained from the capillary flow method should, therefore, be especially relevant to field operations. This investigation was undertaken to evaluate the feasibility of obtaining molecular diffusion coefficients from capillary -flow experiments. In making this evaluation, diffusion coefficients were first determined for two systems from data obtained in capillary flow experiments. These values of the diffusion coefficient were then compared to values obtained by other methods. MIXING IN CAPILLARY FLOW—THEORETICAL The theoretical basis for determining molecular diffusion coefficients from capillary flow experiments is the partial differential equation relating the mechanisms of flow and diffusion. For the case of laminar flow and with a fluid pair having equal densities and viscosities, the equation is given by

By W. B. Gogarty, H. R. Bailey

Methods are presented for determining molecular diffusion coefficients by using data from, capillary flow experiments. These methods are based on a numerical solution (presented in a previous paper) of the partial differential equation describing the combined mechanisms of flow and diffusion. Results from this numerical solution are given and compared with the approximate analytical solution of G. I. Taylor. The numerical solution is valid over a much larger time range. These methods are applied to experimental results for the fluid pairs water-potassium permanganate solution and amyl acetate-orthoxylene. Both of these fluid pairs have approximately equal densities and viscosities. Graphical and numerical techniques are presented for deter mining diffusion coefficients from the flow data. Values obtained by these techniques are compared with values obtained by other methods. INTRODUCTION The molecular diffusion coefficient is known to be a variable in determining the amount of mixing in a miscible displacement process. The effect of molecular diffusion on dispersion in longitudinal flow through porous media -has been examined by different investigators. These investigators concluded that at low velocities of flow, the amount of dispersion is approximate1y proportional to the molecular diffusion coefficient. The influence of diffusion on fingering, channeling, and overriding has been mentioned by other investigators.4 Recent studies5,6 have been made on the effects of molecular diffusion in connection with the problem of gravity segregation. Many different methods have been developed for the experimental determination of molecular diffusion coefficients? These methods differ mainly according to boundary conditions selected and analytical procedures used. Nevertheless, all of these methods have the condition in common that the bulk fluids in which diffusion is occurring are stationary with respect to each other. In connection with a series of papers on mixing in capillary flow,8-10 Taylor suggested the use of a flow method for determining molecular diffusion coefficients. Additional studies 11-13 have been conducted on miscible displacements in capillary tubes, but the data from these studies were not used for the specific purpose of determining diffusion coefficients. The flow method proposed by Taylor results in a single value of the diffusion coefficient for the fluid pair used in the displacement experiments. This single value represents the true value for the fluid pair when the diffusion coefficient is independent of concentration. If the diffusion coefficient is a function of concentration, the single value obtained by the flow method gives an average value for the coefficient of the fluid pair. These average values are based on diffusion taking place over the entire range of concentration, i.e., from 0 per cent of one fluid to 100 per cent of that same fluid. In field applications of the miscible displacement process, gradients occur over the same range of concentration as are found in the displacements in capillary tubes. Molecular diffusion coefficients obtained from the capillary flow method should, therefore, be especially relevant to field operations. This investigation was undertaken to evaluate the feasibility of obtaining molecular diffusion coefficients from capillary -flow experiments. In making this evaluation, diffusion coefficients were first determined for two systems from data obtained in capillary flow experiments. These values of the diffusion coefficient were then compared to values obtained by other methods. MIXING IN CAPILLARY FLOW—THEORETICAL The theoretical basis for determining molecular diffusion coefficients from capillary flow experiments is the partial differential equation relating the mechanisms of flow and diffusion. For the case of laminar flow and with a fluid pair having equal densities and viscosities, the equation is given by

By N. K. Chen, R. Maddin

In the extension of molybdenum single crystals at room temperature, the slip planes were found to be of the type (1101; the slip direction <111>. Theories of plasticity of body-centered cubic metals have been examined, and an explanation based upon planes of highest atomic density seems plausible to explain the plastic behavior of molybdenum single crystals. IN body-centered cubic metals, slip has been reported to occur on several planes; these are of the type {110), {112), and (123). Andrade has correlated&apos; the operative slip planes in body-centered cubic metals with the testing temperature relative to the melting point. In this correlation, if T is the absolute temperature at which slip takes place and Tm the absolute melting point, then the acting slip planes in body-centered cubic metals may be arranged as shown in Table I. However, deviations from this correlation have been reported in iron and iron-silicon alloys2 and also in molybdenum deformed at a temperature around 2400°C." In the case of iron and other body-centered cubic metals or alloys in which all three slip planes have been reported to be active at any one temperature, the crystallographic mechanism of slip is not well understood. Numerous investigators in this field have assumed that the resolved shear stress is a deciding factor. Such considerations were given by Gough in his experiments with repeated torsion of iron single crystals4 and recently by Opinsky and Smoluchowski in their study of iron-silicon alloys," and will be dealt with later in this report. A third possibility is that slip lines in body-centered cubic metals may be formed by alternate slip on nonparallel (110) planes and not by slip on any plane of higher indices. This was advanced by Elam in the case of ß brass." Since (1101 planes are planes of highest atomic density in the body-centered cubic structure, this hypothesis would be in accordance with the plastic behavior of metals in other systems, namely, face-centered cubic and hexagonal close-packed. Experimental evidence in support of this hypothesis is lacking. Nevertheless the work of Barrett, Ansel, and Meh12 has definitely demonstrated that the slip resistance on {110} planes in iron is very much smaller compared with that on (112) and (123) planes. In the present investigation, molybdenum single crystals were carefully documented as to the operative slip planes and lattice reorientations after plastic extension at room temperature. In three crystals studied, (110) planes were found to be active invariably rather than the (112) planes, which were previously reported for molybdenum at this temperature&apos; and predicted by Andrade&apos;s theory.&apos; In two other cases (112) and (123) planes seemed to operate together with (110) planes as active slip planes. However, it is believed, after careful analysis of crystallite and lattice rotations, that slip on (112) and (123) planes may be spurious. Particular reference will be made to the formation of asterism, lattice rotation, and crystallite rotation in an attempt to show that slip apparently observed on {1121} and (123) planes is actually slip on nonparallel {110} planes. Materials and Treatment Sintered molybdenum rods ? in. in diam, obtained from the Fansteel Metallurgical Co., were reported to have a purity of 99.9 pct.* One specimen, Mo-13, ¼ in. in diam, was supplied by Westinghouse Electric Corp. Single crystals were prepared, using the technique devised by Chen, Maddin, and Pond." Mo-13 was ¼ in. in diam x 7 in. long with a reduced gage section of 0.200 in. in diam x 3 in. long. The center of

Jan 1, 1952

By G. W. Nabor, H. J. Ramey

A blotter-type electrolytic model was utilized to prepare flow diagrams for a field test of the in-situ combustion process. It is pointed out that the areal sweep of a combustion pattern is similar to sweep patterns that would be developed at an infinite mobility ratio, which exists (approximately) across a combustion front because of the complete removal of liquids from the sand behind it. The precision of the blotter method was tested by comparison with results obtained by other techniques and was found to be satisfactory. The blotter-type model will not furnish as much information as more elaborate and expensive potentiometric models, but its speed of operation and ease of construction make it a highly satisfactory tool to determine areal sweep patterns. A tabulation of sweep efficiency and mobility ratio is furnished for various well geometries. INTRODUCTION In connection with the first field experiment with the in-situ combustion method of oil recovery," flow diagrams for the unique well geometry and boundary conditions involved in the subject test were developed. From these diagrams, information concerning the areal sweep and distribution of flow was obtained. A survev of the literature on potentiometric models, utilized to solve two-dimensional flow problems,1,2,3,4,5,6,8,9,10 indicated that the information desired could be obtained by means of a blotter-type model by making certain modifications in the technique. The following discussion describes the application of the modified blotter-type electrolytic model to the solution of the problem of the flow of gases in an oil reservoir for an engineering appraisal of the progress of the combustion front during the first field experiment. Considerable information has been published on the theoretical aspects of electrical model techniques. One author stated that:&apos; "The models are based on the observation that since the velocity of an ion in an electrolytic system is proportional to the potential gradient, just as the velocity of a fluid particle in a porous medium is proportional to the pressure gradient, the paths of the ions in the electrolytic systems must be similar to those of the fluid particles in a porous medium with the same geometry and equivalent boundary conditions." This suggestion of a real analogy has been established repeatedly by comparisons of analytic derivations with model results. The analogy between the movement of a combustion front and the model results is not as apparent, since the combustion process differs from water flooding and gas cycling in that the velocity of the burning front is different from the velocity of the injected fluid at the front in combustion. Analogy between electric current flow and movement of the burning front exists because the local velocity of the burning front is proportional to the air (mass) velocity at this point (assuming frontal temperatures are at least as high as the ignition temperature of the fuel). Most model studies fall into one of two categories: (1) electron conduction, or (2) ionic conduction models. Examples of these are models which employ as flow media either a thin metal sheet, or a porous blotter saturated with an electrolyte, respectively. Of the two, the porous blotter model, an ionic conduction model, appears to be the most adaptable to the flow problem that results when using in-situ combustion. This problem requires that the mobility of the particles in the model be controlled analogous to the mobility of gas flowing through burned sand of high permeability to gas and then through oil sand of lower permeability to gas. Although the blotter model has heretofore been

Jan 1, 1955

By M. A. Selim, W. H. Somerton

Thermal expansions and heats of reaction of three typical sandstones were measured in the temperature range of 25°to 1,000°C. The significance of these data in subsurface heat-transfer calculations is discussed. Linear thermal expansions were measured both parallel and perpendicular to the bedding planes. Volume expansions are reported as the perpendicular expansion plus two times the parallel expansion. Expansion behavior of the sandstones was found to be controlled by the expansion characteristics of the quartz content. Differential expansion of the quartz grains and other minerals included in the sandstones caused permanent deformation of the heated samples after they were cooled to room temperature. Structural damage resulting from heating is probably an important cause of the reduction of thermal conductivity of heated samples. Measurements of heats of reaction were based on the known heat required for a- quartz inversion. Thermal reactions, which probably include deby-droxylation of clay minerals and decomposition of carbonate minerals contained within the samples, were found to require more than one-fourth of the amount of heat necessary to raise the temperature of the rock alone. In shales and limestones, the reaction heat could be substantially greater than that required from specific heat considerations alone. INTRODUCTION In earlier work, l-3 methods of measuring thermal properties were developed and thermal data for several sedimentary-rock types were reported. Data included thermal conductivity, specific heat and thermal diffusivity. In addition, calculations of heat transfer in subsurface formations may require data on the thermal-expansion characteristics of rock and the heats of reaction of mineral constituents. Thermal expansion of rocks is relatively small in magnitucle and, from the standpoint of change in bulk density, has only minor effects on heat-transfer cliaracteristics. Thermal-expansion behavior, however, may have significant effects on the structure of rocks. Differential expansion of different minerals and along different crystal-lographic axes may result in structural damage which could effectively reduce the thermal conductivity of the rock. Many mineral constituents of sedimentary rocks undergo phase or related changes when heated to sufficiently high temperatures. Although some of these reactions (such as the a-ß quartz inversion) are reversible and the heat absorbed is returned to the system upon cooling, many of the major reactions are irreversible. Through certain temperature ranges, the additional heat energy required to complete the reactions may be nearly as great as that necessary to raise the temperature of the rock in the absence of thermal reactions. If the heat requirements for these reactions are not considered, serious errors in heat-transfer calculations may result. Thermal-tzxpansion and thermal-reaction data have been obtained for three typical sandstones. Methods of measurement and results obtained are reported and discussed in the following. THERMAL EXPANSION OF SANDSTONES The linear expansions of three outcrop sandstones (Bandera, Berea and Boise) have been measured in the temptbratue range of 25° to 1,000° C. Expansion measurements were made in the directions parallel and perpendicular to the bedding. The differential expansion apparatus used is that described by Mitoff and Pask.4 The test sample is heated in an electric furnace with a temperature rise of 6°C/minute. The lengthening of the samples upon heating is compared with the small and known expansion of a fused silica rod. The change in length is transmitted to an X-Y recorder by means of a Statham transducer. A maximum error of ± 1.5 per cent has been obtained with this apparatus

By R. C. Edwards, T. G. Kirkland, Will Mitchell

A scrubber of new design has been invented for the beneficiation of glass and chemical sands. The machine is described and its capacity and metallurgical efficiency compared with the performance of other sand cleaning devices. THREE years ago, when the Process Research Laboratory at Allis-Chalmers Manufacturing Co. sought a remedy for the increasing cost of disposing of great quantities of spent sands from foundries, R. C. Edwards developed a continuous inclined paddle scrubber which removed a substantial amount of the charred coatings from the grains with a surprisingly small amount of degradation of the sand itself.&apos; The satisfactory results obtained on foundry sand, using this piece of equipment in conjunction with classification, suggested that a similar procedure could probably be applied to the cleaning of other sands, such as those required by the glass and chemical industries. This paper describes the flowsheet and the results of tests performed on impure natural sands. The four materials tested were silica sands obtained from widely separated geographical areas. Three of the sands tested contained various amounts of iron oxide and the fourth an excessive amount of calcareous bonding material. The iron oxide was present predominantly in the form of grain coatings, which were scuffed by the paddle scrubber, and in all cases a product was manufactured which would meet one of the sets of specifications imposed by the glass industry.&apos; The Edwards paddle scrubber used in these tests consists of a rubber-lined steel cylinder 18 in. in diam and 48 in. long, mounted on a frame so that its slope can be varied 5" to 35" from horizontal. This variable slope permits controlled flow of material through the machine. Rubber paddles rotate inside the cylinder and are secured to a center shaft 2 in. square, which extends through the entire length and is turned at both ends so that it can be supported by sleeve bearings centrally fixed in the end plates of the shell. At the upper or feed end it extends through the bearing on the end plate into a sheave, to which the motor drive is connected by means of Texrope transmission. The four sets of paddles mounted on the shaft, two in each set, are made of rubber belting, 1/4 in. thick, 9 in. wide, and 16 in. long. The two paddles in each set are secured on opposite sides of the square shaft, but in the same longitudinal position along the shaft axis. In other words, the two paddles in the set operate 180" apart. Each successive set is mounted 90" from the preceding one. One end of each paddle is bolted to the square shaft and the other weighted by a steel bar, lx1 1hx9 in. long, which is attached about Yz in. from the outer tip of the paddle. By centrifugal force at proper shaft speed, these weights force the paddle surface to rub smoothly against the rubber lining of the cylinder. During operation, the sand forces its way between the paddle face and the surface of the cylinder, providing the necessary abrading action as the pulp flows by gravity down the length of the cylinder. The capacity of the machine is limited by the amount and the hardness of the coating material and by the quality of product desired. The degree of scrubbing is governed by the retention time in the scrubber, which in turn may be changed by varying the feed rate, water content of the feed, and

Jan 1, 1953

By R. C. Edwards, T. G. Kirkland, Will Mitchell

A scrubber of new design has been invented for the beneficiation of glass and chemical sands. The machine is described and its capacity and metallurgical efficiency compared with the performance of other sand cleaning devices. THREE years ago, when the Process Research Laboratory at Allis-Chalmers Manufacturing Co. sought a remedy for the increasing cost of disposing of great quantities of spent sands from foundries, R. C. Edwards developed a continuous inclined paddle scrubber which removed a substantial amount of the charred coatings from the grains with a surprisingly small amount of degradation of the sand itself.&apos; The satisfactory results obtained on foundry sand, using this piece of equipment in conjunction with classification, suggested that a similar procedure could probably be applied to the cleaning of other sands, such as those required by the glass and chemical industries. This paper describes the flowsheet and the results of tests performed on impure natural sands. The four materials tested were silica sands obtained from widely separated geographical areas. Three of the sands tested contained various amounts of iron oxide and the fourth an excessive amount of calcareous bonding material. The iron oxide was present predominantly in the form of grain coatings, which were scuffed by the paddle scrubber, and in all cases a product was manufactured which would meet one of the sets of specifications imposed by the glass industry.&apos; The Edwards paddle scrubber used in these tests consists of a rubber-lined steel cylinder 18 in. in diam and 48 in. long, mounted on a frame so that its slope can be varied 5" to 35" from horizontal. This variable slope permits controlled flow of material through the machine. Rubber paddles rotate inside the cylinder and are secured to a center shaft 2 in. square, which extends through the entire length and is turned at both ends so that it can be supported by sleeve bearings centrally fixed in the end plates of the shell. At the upper or feed end it extends through the bearing on the end plate into a sheave, to which the motor drive is connected by means of Texrope transmission. The four sets of paddles mounted on the shaft, two in each set, are made of rubber belting, 1/4 in. thick, 9 in. wide, and 16 in. long. The two paddles in each set are secured on opposite sides of the square shaft, but in the same longitudinal position along the shaft axis. In other words, the two paddles in the set operate 180" apart. Each successive set is mounted 90" from the preceding one. One end of each paddle is bolted to the square shaft and the other weighted by a steel bar, lx1 1hx9 in. long, which is attached about Yz in. from the outer tip of the paddle. By centrifugal force at proper shaft speed, these weights force the paddle surface to rub smoothly against the rubber lining of the cylinder. During operation, the sand forces its way between the paddle face and the surface of the cylinder, providing the necessary abrading action as the pulp flows by gravity down the length of the cylinder. The capacity of the machine is limited by the amount and the hardness of the coating material and by the quality of product desired. The degree of scrubbing is governed by the retention time in the scrubber, which in turn may be changed by varying the feed rate, water content of the feed, and

Jan 1, 1953

By R. C. Edwards, Will Mitchell, T. G. Kirkland

A scrubber of new design has been invented for the beneficiation of glass and chemical sands. The machine is described and its capacity and metallurgical efficiency compared with the performance of other sand cleaning devices. THREE years ago, when the Process Research Laboratory at Allis-Chalmers Manufacturing Co. sought a remedy for the increasing cost of disposing of great quantities of spent sands from foundries, R. C. Edwards developed a continuous inclined paddle scrubber which removed a substantial amount of the charred coatings from the grains with a surprisingly small amount of degradation of the sand itself.&apos; The satisfactory results obtained on foundry sand, using this piece of equipment in conjunction with classification, suggested that a similar procedure could probably be applied to the cleaning of other sands, such as those required by the glass and chemical industries. This paper describes the flowsheet and the results of tests performed on impure natural sands. The four materials tested were silica sands obtained from widely separated geographical areas. Three of the sands tested contained various amounts of iron oxide and the fourth an excessive amount of calcareous bonding material. The iron oxide was present predominantly in the form of grain coatings, which were scuffed by the paddle scrubber, and in all cases a product was manufactured which would meet one of the sets of specifications imposed by the glass industry.&apos; The Edwards paddle scrubber used in these tests consists of a rubber-lined steel cylinder 18 in. in diam and 48 in. long, mounted on a frame so that its slope can be varied 5" to 35" from horizontal. This variable slope permits controlled flow of material through the machine. Rubber paddles rotate inside the cylinder and are secured to a center shaft 2 in. square, which extends through the entire length and is turned at both ends so that it can be supported by sleeve bearings centrally fixed in the end plates of the shell. At the upper or feed end it extends through the bearing on the end plate into a sheave, to which the motor drive is connected by means of Texrope transmission. The four sets of paddles mounted on the shaft, two in each set, are made of rubber belting, 1/4 in. thick, 9 in. wide, and 16 in. long. The two paddles in each set are secured on opposite sides of the square shaft, but in the same longitudinal position along the shaft axis. In other words, the two paddles in the set operate 180" apart. Each successive set is mounted 90" from the preceding one. One end of each paddle is bolted to the square shaft and the other weighted by a steel bar, lx1 1hx9 in. long, which is attached about Yz in. from the outer tip of the paddle. By centrifugal force at proper shaft speed, these weights force the paddle surface to rub smoothly against the rubber lining of the cylinder. During operation, the sand forces its way between the paddle face and the surface of the cylinder, providing the necessary abrading action as the pulp flows by gravity down the length of the cylinder. The capacity of the machine is limited by the amount and the hardness of the coating material and by the quality of product desired. The degree of scrubbing is governed by the retention time in the scrubber, which in turn may be changed by varying the feed rate, water content of the feed, and

Jan 1, 1953

By R. C. Edwards, Will Mitchell, T. G. Kirkland

A scrubber of new design has been invented for the beneficiation of glass and chemical sands. The machine is described and its capacity and metallurgical efficiency compared with the performance of other sand cleaning devices. THREE years ago, when the Process Research Laboratory at Allis-Chalmers Manufacturing Co. sought a remedy for the increasing cost of disposing of great quantities of spent sands from foundries, R. C. Edwards developed a continuous inclined paddle scrubber which removed a substantial amount of the charred coatings from the grains with a surprisingly small amount of degradation of the sand itself.&apos; The satisfactory results obtained on foundry sand, using this piece of equipment in conjunction with classification, suggested that a similar procedure could probably be applied to the cleaning of other sands, such as those required by the glass and chemical industries. This paper describes the flowsheet and the results of tests performed on impure natural sands. The four materials tested were silica sands obtained from widely separated geographical areas. Three of the sands tested contained various amounts of iron oxide and the fourth an excessive amount of calcareous bonding material. The iron oxide was present predominantly in the form of grain coatings, which were scuffed by the paddle scrubber, and in all cases a product was manufactured which would meet one of the sets of specifications imposed by the glass industry.&apos; The Edwards paddle scrubber used in these tests consists of a rubber-lined steel cylinder 18 in. in diam and 48 in. long, mounted on a frame so that its slope can be varied 5" to 35" from horizontal. This variable slope permits controlled flow of material through the machine. Rubber paddles rotate inside the cylinder and are secured to a center shaft 2 in. square, which extends through the entire length and is turned at both ends so that it can be supported by sleeve bearings centrally fixed in the end plates of the shell. At the upper or feed end it extends through the bearing on the end plate into a sheave, to which the motor drive is connected by means of Texrope transmission. The four sets of paddles mounted on the shaft, two in each set, are made of rubber belting, 1/4 in. thick, 9 in. wide, and 16 in. long. The two paddles in each set are secured on opposite sides of the square shaft, but in the same longitudinal position along the shaft axis. In other words, the two paddles in the set operate 180" apart. Each successive set is mounted 90" from the preceding one. One end of each paddle is bolted to the square shaft and the other weighted by a steel bar, lx1 1hx9 in. long, which is attached about Yz in. from the outer tip of the paddle. By centrifugal force at proper shaft speed, these weights force the paddle surface to rub smoothly against the rubber lining of the cylinder. During operation, the sand forces its way between the paddle face and the surface of the cylinder, providing the necessary abrading action as the pulp flows by gravity down the length of the cylinder. The capacity of the machine is limited by the amount and the hardness of the coating material and by the quality of product desired. The degree of scrubbing is governed by the retention time in the scrubber, which in turn may be changed by varying the feed rate, water content of the feed, and

Jan 1, 1953

By B. Haimson, C. Fairhurst

A criterion is Proposed for the initiation of vertical hydraulic fracturing taking into consideration the three stress fields around the wellbore. These fields arise from (1) nonhydrostatic regional stresses in earth, (2) the difference between the fluid pressure in the wellbore and the formation fluid pressure and (3) the radial fluid flow through porous rock from the wellbore into the formation due to this pressure difference. The wellbore fluid pressure required to initiate a fracture (assuming elastic rock and a smooth wellbore wall) is a function of the porous elastic constants of the rock, the two unequal horizontal principal regional stresses, the tensile strength of the rock and the formation fluid pressure. A constant injection rate will extend the fracture to a point where equilibrium is reached and then, to keep the fracture open, the pressure required is a function of the porous elastic constants of the rock, the component of the regional stress normal to the plane of the fracture, the formation fluid pressure and the dimensions of the crack. The same expression may also be used to estimate the vertical fracture width, provided all other variables are known. The derived equations for the initiation and extension pressures in vertical fracturing may be employed to solve for the two horizontal, regional, principal stresses in the rock. INTRODUCTION Well stimulation by hydraulic fracturing is a common practice today in the petroleum industry. However, this stimulation process is not a guaranteed success; hence, the deep interest shown by the petroleum companies in better understanding the mechanism that brings about rock fracturing, fracture extension and productivity increase. Geologists and mining people became interested in hydraulic fracturing from a different point of view: the method may possibly be employed to determine the magnitude and direction of the principal stresses of great depth. Numerous articles in past years have dealt with the theory of hydraulic fracturing, but they all seem to underestimate the effect of stresses around the wellbore due to penetration of some of the injected fluid into the porous formation.1-4 Excellent papers on stresses in porous materials due to fluid flow have been published5,6 but no real attempt has been made to show the effect of these stresses in the form of a more complete criterion for vertical hydraulic fracturing initiation and extension. This paper is such an attempt. ASSUMPTIONS It is assumed that rock in the oil-bearing formation is elastic, porous, isotropic and homogeneous. The formation is under a nonhydrostatic state of regional stress with one of the principal regional stresses acting parallel to the vertical axis of the wellbore. This assumption is justified in areas where rock formations do not dip at steep angles and where the surface of the earth is relatively flat. This vertical principal regional stress equals the pressure of the overlying rock, i.e., S33 = —pD, where S33 is the total vertical principal stress (positive for tension), p is average density of the overlying material and D is the depth of the point where S33 is calculated. The wellbore wall in the formation is considered to be smooth and circular in cross-section. The fluid flow through the porous elastic rock obeys Darcy&apos;s law. The whole medium is looked upon as an infinitely long cylinder with its axis along the axis of the wellbore. The radius of the cylinder is also very large. Over the range of depth at which the oil-bearing formation occurs, it will be assumed that any horizontal cross-section of the cylinder is subjected to the same stress distribution, and likewise that it will deform in the same manner. STATE OF STRESS PRIOR TO DRILLING OF WELLBORE At a depth D from the earth surface within the oil-bearing strata, it is assumed that the following are 1References given at end of paper.

By E. Topanelian

In recent years considerable progress has been made in the development and application of mathematical techniques for the solution of certain problems involving economic "strategies". Such a problem might involve, for example, the scheduling of shipments of a commodity from a number of sources to a number of destinations. The object would be to schedule the shipments in a manner so as to satisfy the destination requirements and at the same time minimize the transportation costs. The solution to such a problem is not necessarily intuitively obvious. The "obvious" solution is frequently far from optimum. If the shipments are to be made from, for example, only two sources to four destinations, the optimum schedule is readily found. However, if shipments are to be made from, say, 10 sources to several hundred destinations, even a competent and experienced scheduler may spend considerable time in finding a reasonable answer. Even then he is not sure that he has the optimum solution. Furthermore, he has no way of knowing how far from optimum the answer is. Consequently, he does not know whether he should accept this solution or seek a better one. Prior to the advent of large high-speed digital computers, little more could be done with such problems because of their great size and multiplicity of possible solutions. A problem involving 20 sources and 50 destinations would require choosing, from a very large number of possible combinations, the optimum combination of 1,000 variables. The best one could do was to utilize intuition, extrapolation from past experience, and other non-exact approaches. With a high-speed computer, however, such problems can be solved providing a reasonable computational procedure (or algorithm) can be utilized. The purpose of this paper is to describe such a procedure (linear programming) and to apply this procedure to a production scheduling problem. THE RESERVOIR PROBLEM A simple reservoir model is used throughout this analysis to illustrate the use of linear programming. Even the simplest reservoir behavior problem is nonlinear in both space and time, but if the geometry is fixed for a particular study and the time variable is quantized, the resultant system may be described by linear constraints on the variable production rates. Crude oil is available from five separate sources and is delivered to a pipeline. Sources 1, 2, 3 and 4 are ideal reservoirs and therefore are subjected to reservoir flow restrictions. Source 5 is labeled "Outside Source" and crude oil from this source is assumed to be available in unlimited quantities without considering reservoir conditions. The general problem is to determine the schedule of crude oil production from five sources which, over an eight-year period and subject to certain restrictions, will result in maximum profit. "Profit" is defined to encompass all economic factors and expenses involved in producing and selling crude oil to a pipeline facility. Such economic factors are lumped to the extent that the term represents the dollars profit from one barrel of crude oil from any of the five sources entering the pipeline system. Table 1 presents the assumed profit per barrel for oil from any of the five sources over each of the four time periods. In this chart the eight years is broken into four equal intervals of two years. The selection of four time periods of two years each and the values representing the potential profit are completely arbitrary selections for the purpose of illustrating this idealized reservoir problem. In any practical application of this work a careful economic study would have to be made in order to estimate potential unit profits for time periods as far in the future as eight years. In this particular study it is assumed that all of the potential unit profits (C) are known and fixed before the production schedule is attempted. For each reservoir arbitrary values are assigned for

By B. Trafton, H. L. Hartman

An earlier paper1 introduced a rapid solution for mine ventilation network problems, employing the digital computer. In this paper, refinements and additions to the computer program which expand its scope of application and a solution to a ventilation network having a coal-mine configuration are presented. The revised program-written in FORTRAN for the IBM 7074 computer in Penn State&apos;s Computation Center-is applicable to any mine ventilation network employing natural splitting and having its fan located externally. It accomplishes the following: 1) Distributes an assumed total quantity of air flow among all airways of the network, performing iterations until an acceptable level of error is attained and the flow in each airway is known. 2) Computes the pressure drop (head loss) in all airways and the overall network and mine head losses. 3) Determines the operating point for the mine and a given fan, adjusting all air flows and head losses to the actual values. The basis of analysis used is the Hardy Cross method of successive approximation for solution of any fluid network, explained in detail in the earlier article. In brief, corrections to assumed air flows are computed for all the loops of a network; following distribution to the airways of each loop, the process is repeated until acceptable accuracy is attained. When a hand or desk-calculator solution is used, there is advantage to close approximation of the actual flows in the original assumption of air-flow distribution in the network. Since publication of the previous paper, in which assumption of initial quantities was also necessary in the computer solution, the program has been modified to make the first distribution itself, assigning the total quantity to one specified path in a split and then proceeding to correct the flows. The number of iterations required for a high-accuracy solution is little affected, at least in networks of few loops, 10 to 15 being sufficient to reduce the error to 1 pct or less. The principal limitation of the original program was that it contained no provision for handling a fan. Further, it did not determine the overall head loss in the network and was not designed for multiple parallel openings, such as occur in coal mines. The revised program was written to overcome these disadvantages and also to print out the adjusted flows for all airways, corrected for the system operating point. At the present time, the program can handle only an external fan. The procedure employed in solving a ventilation network is now as follows: 1) Input data consisting of airway characteristics and loop designation along with assumed direction of flow, for each branch of the network and any trunk airways, are fed into the computer. 2) Employing the resistance relationship, where R is resistance, K is friction factor, P is perimeter, L is length, A is area, and n is number of airways (where multiple intakes and returns are employed); values are computed for all airways. 3) An arbitrary, continuous route of flow through the circuit—from beginning to end—is selected and the path identified by airway numbers and read in. 4) Based on a total assumed quantity of flow Q (usually 100,000 cfm.) the computer employs the procedure described in the previous article in distributing quantities of flow among all the airways until a satisfactory level of accuracy has been attained (in the current program, the machine is turned off when the cumulative corrective error in cfm, is reduced to five times the number of airways). 5) Airway head losses H are calculated by the relation H = R Q2 and cumulated along the original designated flow route to find the overall head loss for the network. Trunk airways are then included to obtain the mine head.

Jan 1, 1964

By John F. Elliott, John R. Rawling

The rate of reduction of silica to silicon by carbon at 1550° to 1700°C in iron blast-furnace type slag-metal systems has been investigated. In the tower portion of the temperature range oxygen transport in the metal boundary layer at the slag-tal interface is probably rate limiting. A second step, which apparently involves a chemical process in the slag at the slag-metal interface, appears to be rate limiting when the oxygen-transport limitation is avoided. Above 1650°C rate control of the reduction by carbon probably is mixed between the two steps. INVESTIGATIONS1.2 into the equilibrium distribution of silicon between graphite-saturated slags and metals typical of iron blast-furnace practice show that, under the experimental conditions specified, the reduction of silica to silicon is relatively slow compared with the rates of other slag-metal reactions under similar conditions. For this reason, the reduction of silica in blast-furnace slag-metal systems was considered to be an interesting subject for further study. Investigations of the kinetics of the reaction3-5 suggest that several possible steps may be rate controlling, and that the rate-controlling step depends not only on the physical state of the systems but also on the configuration of the apparatus. The main objects of the investigation reported here were to sug- gest plausible reaction paths for the reduction of silica under the experimental conditions chosen and to determine the step or steps which control the rate of reduction of silica. EXPERIMENTAL Two types of experiments involving the reduction of silica from the slag were carried out. In the first, the only reducing agent present was carbon (graphite), for which the over-all reaction is (SiO2) +2C(gr) —Si + 2Co(g) [l] The second type was a graphite-saturated ferro-silicon-iron concentration cell. In it silica in the slag could be reduced either by carbon according to Eq. [I], or by a reaction of electrochemical nature in which silicon was oxidized at the ferrosilicon-slag interface and silica was reduced at the slag-iron interface without the formation of CO. The two types of experiment are described below. Reduction of Silica with Carbon as the Only Available Reducing Agent. The reduction of silica was accomplished by allowing a liquid lime-alumina-silica slag and graphite-saturated iron to react in an induction-heated graphite crucible. The crucible was 2.25 in. diameter and 5 in. deep; it was fitted with a graphite stirrer which penetrated through the slag and into the metal, Fig. 1. The slag and metal charges weighed 350 g each. Pure carbon monoxide at a pressure of 1 atm was maintained above the melt by passing the purified gas through the crucible at a rate of 0.5 liter per min. The gas did not stir either the slag or metal. Temperature measurements were made by sighting an optical pyrometer down the hollow stirrer rod into a 1/4-in. hole drilled in the stirrer blade. The crucible temperature was maintained within *15"C of the required value by manual control of the power supply to the

Jan 1, 1965

By F. E. Rizzo, L. R. Bidwell, D. F. Frank

THE poor high-temperature oxidation resistance of the refractory metals becomes an important problem as higher operating temperatures are sought. A meaningful analysis of their oxidation behavior requires a knowledge of the phases that can appear during oxidation as well as their relative stability. Although several extensive investigations have been carried out to obtain this information for the W-0 system,1-10 serious inconsistencies still remain. First, the standard free energies of formation (AG°) determined in recent studies which used the solid electrolyte galvanic cell technique6,7,9 differ significantly from those obtained primarily from gas equilibration measurements.1,3,4,10 The disagreement is especially large for the highest oxides. These data have been used to predict the decomposition temperatures of WO2. 72 and WO2.90.1 A considerable extrapolation is required, resulting in a large uncertainty in the decomposition temperatures. Second, Bousquet and perachon3 have presented convincing evidence, ob- tained by gas equilibration measurements, in support of the long-contested existence of W30. Phillips and chang,ll on the other hand, were not able to observe this phase under similar experimental conditions. The purposes of this work, which is part of a continuing investigation of the W-Mo system, were to resolve the discrepancies between the AGO measured by gas equilibration and solid electrolyte galvanic cell techniques, to extend the latter measurements to lower temperatures, to redetermine the WO2.72 and WO2.90 decomposition temperatures, and to apply the more sensitive electromotive-force method to the question of the existence of W3O. I) EXPERIMENTAL PROCEDURE The measurement of ?G° of reaction by the use of calcia-stabilized zirconia solid electrolyte galvanic cells has been described previously.12 The method is based on the measurement of the difference in chemical potential of oxygen between an electrode containing the two oxides of interest and a reference electrode of known oxygen activity. Two different types of cell holders were used in this study. The first type of apparatus has been described earlier." It consisted of two solid electrodes separated by a disc of electrolyte. Both electrodes were exposed to the same stream of purified helium. With this design a gaseous transport of oxygen between the two electrodes is possible. The second type of apparatus, which has also been described earlier,14 effectively separated the two electrode atmospheres. It utilized a closed-end impervious, calcia-stabilized zirconia tube that was open to the atmosphere. The tube served as an electrolyte for the cell and provided a means for separating the anode compartment, which was held under a static vacuum, from an air reference cathode. The cells and reactions of interest are described in Table I. High-purity tungsten metal was obtained from the Fansteel Metallurgical Corp. and the Allied Chemical Corp. Table II contains an analysis of each material. WO3 was prepared by oxidizing the metal in air at approximately 600°C in high-purity recrystallized alumina boats and by the dehydration of reagent-grade tungstic acid in alundum boats. The two methods of preparing WO3 resulted in slightly different purities.

Jan 1, 1968

By N. F. Foster

The use of piezoelectric semiconducting materials for the fahrication of ultrasonic transducers has raised the upper fundamental frequency limit for transducers from about 200 mc to above 10 kmc, Several types of semiconductor transducer configurations have been proposed and examined experimentally. Depletion-layer transducers have been made and operated at frequencies below 1 kmc hut they appear to he better suited for operation at considerably higher frequencies around 10 knzc. Diffusion-layer transducers have been made and operated in the range 50 to 1000 mc and have exhihited considerably improved conversion losses and bandwidths compared with other transducers available in the frequency range. A variety of novel structures are possible using these new types of transducers, some of which could lead to substantial advances both in research and in the fabrication of ultrasonic delay lines and memory elements. THE field of ultrasonics today spans some five decades of the frequency spectrum from the audible to the kmc range and finds applications ranging from fundamental research into the atomic structure of matter to the degreasing of machine parts. To cover this wide range it has been necessary to develop a great many types of ultrasonic trandsucers utilizing a variety of materials and physical phenomena. The first ultrasonic transducers were made during World War I for a submarine-detection system. They consisted of plates of single-crystal quartz bonded between metal plates and were one of the first applications of the phenomenon of piezoelectricity discovered nearly 30 years previously. Despite the many advances which have been made in transducer technology, piezoelectric transducers using single-crystal quartz are still used almost exclusively for application above about 30 mc. Transducers at these frequencies are normally made in the form of thin quartz plates which are then bonded onto the medium in which the ultrasonic wave is to be propagated. The crystallographic orientation and geometry of these plates determines the type of wave generated and the way in which the efficiency of the electromechanical conversion varies with frequency. Analysis of the design parameters shows1 that the frequency of maximum efficiency (the fundamental or resonant frequency) is that frequency at which the transducer is approximately half the wavelength of the ultrasonic wave in the material. As the frequency increases, the ultrasonic wavelength, and therefore the optimum transducer thickness, decreases and in practice the fabrication of quartz transducers with fundamental freauencies above 100 mc becomes extremely difficult due to the extreme thinness required. For frequencies above 100 mc quartz transducers can be used in overtone-mode operation, and for very high frequencies (500 to 24,000 me) a technique using a quartz rod inserted in a high-Q microwave cavity4 is available. These techniques, however, exhibit comparatively low fractional bandwidths and rather poor conversion efficiencies. The present trend in ultrasonics is towards high frequencies and greater bandwidth to allow the use of shorter pulses which can give increased discrimination in radar-system delay lines and greater storage capacity in computer applications. The increasing demand for more efficient transducers with greater bandwidth

Jan 1, 1964

By J. E. Pavlick, A. G. Guy

The total creep of tin alloys containing antimony in solid solution was observed to decrease with increase in antimony content. However, near the solubility limit an anomalous maximum in deformation was. found, in agreement with similiar observations by Bochvar. IT has long been recognized that alloys may deform more rapidly under stress if there is a tendency for a phase change or other structural change to occur simultaneously. However, the phenomena involved are complex and in some instances the opposite effect, strengthening, may result.&apos; This area of research has not attracted much interest in the western world, and although Russian investigators have studied it for the past 15 years their work has not received due attention here. Recently diametrically opposing views on one aspect of this problem have been espoused by two Russian investigators, Kornilov and Bochvar. The question is this: in certain binary alloys tested in creep at the temperature where the solute is at the limit of solid solubility, does the incipient formation of the second phase strengthen or weaken the alloy? Korni-lov&apos;s arguments in favor of strengthening were presented at the 1954 Symposium at the National Physical Laboratory, =Creep and Fracture of Metals at High Temperatures.The most recent statement of Boch-var&apos;s theory of weakening is in Oding&apos;s new book on creep and rupture.3 Although Bochvar agrees that strengthening occurs in some alloy systems, he argues that in certain alloys an anomalous weakening is observed. However, the extensive work of Korni-lov&apos;s group on creep properties of alloy systems has not revealed any anomaly of this type, but instead has tended to refute Bochvar&apos;s theory. This clear-cut controversy offered a good opportunity for a simple experiment to resolve the problem. The experiment and its results supporting Bochvar are the subject of this paper. However, it will be helpful first to sketch the present status of the larger question of the effect of a phase change or other structural change on plastic deformation. PREVIOUS WORK One of the first researches in this area was by Pfei1,37 who investigated the creep resistance of an 80 Ni-20 Cr alloy containing varying amounts of titanium. He found that the resistance to creep increased rapidly as the solid solubility limit in the alloy at 775&apos;c was approached and slightly exceeded. With further addition of titanium the creep resistance decreased, presumably because of precipitation effects. Bochvar&apos;s first work in this field was a study in 1945 of "superplasticity" in zinc alloys containing 15 to 25 pct Al.4 He found that alloys quenched from about 400 had anomalously low hardness when tested below this temperature. The following year, in a paper on the dependence of mechanical properties on the composition and structure of alloys,5 he extended some observations of Kurnakov to predict that at high temperatures of testing the hardness values for solid-solution alloys might be lower than those for the component metals. He also pointed out the influence of changes in solidus temperature in affecting curves of hardness vs composition, and he

Jan 1, 1962

By E. Buehler, J. E. Kunzler

High-pu.1-ity molybdenum has been heat treated, melted, and zone refined and the physical and chemical changes that are produced by these processes have been studied by making resistance ratio measurements. Pronounced effects are observed that are associated with recrystalliza-tion at about 1200°C and with melting. Melting alone is found to result in a substantial purification by the evaporation of impurities such as iron. Zone refining is found to be reasonably effective with four passes producing a three-fold decrease in resistance ratio and a minimum ratio of 0.0003. With the aid of low temperature measurenzents, it has been shown that the build-up of a deposit of the material being zone refined on the radio frequency coil used for heating can lead to contamination of the sample. CONSIDERABLE interest in high-purity refractory metals for the study of mechanical properties has developed during recent years. Also the need for highly pure metals in certain fundamental studies, such as electronic band structure, has become quite widely appreciated. Molybdenum can now be produced with sufficiently high purity to make it attractive for such investigations. The most suitable measure of chemical purity of metals used for many of these studies is its resistance ratio, R,.,o,/Ro, During the purification of molybdenum by zone refining and its subsequent evaluation by this technique, a number of informative observations were made. These observations concern the effectiveness of zone refining, the volatilization of impurities at the melting point, and the recrystallization of molybdenum and appear to be pertinent to other refractory metals. Also, the usefulness of low-temperature resistance measurements as an analytical tool for evaluating the presence of chemical impurities and physical defects in metals is again illustrated. Samples of high-purity molybdenum of known mechanical history were heated to various temperatures between 800°c and their melting point. Resistance ratios of the samples were measured after they had been given a specified treatment. The data were used, along with mass spectrographic analysis, as an aid in interpreting the nature of the processes that occurred in conjunction with each treatment. Changes in the concentrations of chemical impurities and physical defects are typical of things that effect the low-temperature resistivity. SAMPLES The starting material was obtained from Westing-house Corp., Bloomfield, N.J. It was in the form of molybdenum rods, usually 1/8 or 3/16 in. in diameter. These had been previously processed from bars, 5/8 in, in diameter, originally reduced from 4 in. diam arc-cast ingots, by hot swaging at about 1300°c. In the final step, the temperature was lowered to about l lOO°C which resulted in the production of elongated grains. Typical grains were about 0.03 mm thick and 0.6 mm long. The molybdenum was quite pure as is indicated by the results of mass spectro-scopic analysis1 given in Column 2 of Table I. Other nongaseous elements not listed in the table were not detected. ZONE REFINING AND THERMAL TREATMENT OF SAMPLES Several sample rods, 8 to 10 in. long, were zone refined or were heat treated at several temperatures. Both types of operations were performed using 3 me-

Jan 1, 1962

By C. C. Clark, J. S. Iwanski

The purpose of this investigation was to study mi-crostructural changes that take place in a commercial nickel-chromium-iron alloy, such as Incoloy "901," over long periods of time at temperatures up to 13 50°F and to correlate such changes with creep-rupture properties. of the alloy. In the course of the investigation, some microstructural changes were observed which correspond to microstructural alterations found in previous studies of Inconel "X." Microstructural phases have been identified in both alloys with the aid of electron and X-ray diffraction and an electron probe microanalyzer. The materials used in this investigation were from commercial heats of the following chemical composition: Pct Cr Pct Ni Pct Mo Pct Fe Pct Cb Incoloy "901" 12.51 43.67 5.72 Bal. -Inconel "X" 14.61 73.44 - 6.61 1.02 Pct A1 Pct Ti Pct Mn Pct Si Pct C Incoloy "901" 0.10 2.46 0.46 0.24 0.05 Inconel "X" 0.70 2.43 0.51 0.36 0.04 Long-term creep-rupture tests were conducted on Incoloy "901" at temperatures of 1000°, 1200°1 and 1350°F. A summary of these results is shown in Table I along with the results of a long-term creep-rupture test conducted on Inconel "X" at 1500°F. The heat treatments given the specimens are also shown in Table I. When the creep-rupture results on Incoloy "901" are compared with shorter-tertn data, there is no evidence of any undue deterioration of the creep-rupture strength with time, nor is the elongation decreased more than would be expected from the influence of time alone. INCOLOY "901" PHASE IDENTIFICATION Microscopic examination of the Incoloy "901" specimens reveals a dark etching grain boundary constituent in the specimen which was under test for about 11,500 hr at 1000°F. This grain boundary constituent was seen to increase in size as the test temperature was increased to 1200" and 1350°F, Figs. 1, 2, and 3. Simultaneously, an acicular structure of definite crystallographic orientation appears within the grains of the 1350°F specimen, Fig. 3. Under examination with the electron microscope, a fine precipitate is observed in the 1200 °F specimen. Fig. 4. It becomes considerably larger in the 2850-hr 1350°F specimen, Fig. 5. In a few areas the precipitated particles have been replaced by, or transformed to, small needles or platelets. After 7380 hr at 1350°F, Figs. 3 and 6, the needles are much larger and have replaced nearly all of the fine precipitate. X-ray diffraction studies detected the presence of hexagonal Laves phase and hexagonal n phase (Ni,Ti) in the 1350°F specimens, Table 11. Only the Laves phase was detected by X-ray diffraction in the 1200°F specimen and none was detected in the 1000°F specimen. In this latter specimen, however, the small quantity of precipitate in the grain boundaries (presumed to be Laves phase) precludes its detection by X-ray diffraction. Composition of the hexagonal Laves phase is not yet known, although its diffraction

Jan 1, 1960

By D. A. Dahlstrom

WITHIN the past decade, certain economic, legal, and technological changes have intensified the necessity for an efficient classifier or deslimer of particles at and below the 200-mesh point. First, mechanization of mining has increased the percentage of clays, silts, refuse, and high-ash material in the run-of-mine coal. Second, many washing plants must rely on smaller percentages of fresh make-up water because of shortages, economic factors, or legal restrictions on waste water disposal. Finally, the crushing of middlings and coarse refuse plus the trends toward the finer sizes in sales has further increased the amount of fines produced per ton of mine-run coal. A joint consequence of these circumstances has been the augmented percentage and build-up of —200-mesh material in the finer coal fractions and tipple circulating water. This results in the following disadvantages to the operator: (1) Higher ash percentages in the fine coal caused in large measure by the greater ash content of the —200-mesh material, (2) more difficult or expensive recovery of the fine coal from plant slurries, (3) lower filtration, drainage, and drying rates caused chiefly by lower permeability and the greater surface exposed per unit mass of the finer particles, (4) greater difficulty of beneficiatiing the fine coal because of lowered equipment efficiency and the partial "coating-out" of the —200-mesh fraction on the coarser coal particles. Obviously some cheap but effective fine-size classifier must be developed to aid in solving the above problems. To eliminate the generally unwanted —200-mesh fraction from coal slurries, several methods are in use. Probably the most popular with coal operators is the settling cone wherein the larger particles settle downward to the apex of an inverted cone while the slimes and fines are carried upward by vertical fluid currents caused by the overflow of the bulk of the water at the outer rim. The main advantage of the unit is the low initial and operating cost since no moving parts are involved. Disadvantages are primarily low capacity per square foot or floor space and the loss of good coal in the overflow above the 100-mesh size due to localized, high-velocity gradients and nonuniform, fluid-flow patterns, especially at high loadings. Also, when high slime concentrations are present, desliming efficiency is severely injured.&apos;, &apos; Other methods employed are the drag and spiral classifiers and the hydroseparator.&apos; These involve mechanical separations achieved by moving parts and naturally result in higher initial costs. As they are all based on the settling velocity of the particles at the mesh of separation under operating conditions, area requirements are again large per gallon of throughput if they are to classify at the 200-mesh point. Usually the selection is made to operate at a higher throughput and thus sacrifice some coarser coal in the slime overflow. Cyclone Possibilities in Desliming To overcome the disadvantages of present deslirning methods, it is necessary to use a device that exhibits a very stable and uniform flow pattern while greatly increasing the settling velocity of

Jan 1, 1952

By Douglas A. Karvonen

INTRODUCTION Although the economy in the Province of Saskatchewan has historically been agriculturally oriented, a major source of wealth has been realized through natural resources such as petroleum and natural gas, coal and uranium and since the 1960&apos;s - potash. Potash or potassium chloride, in the form in which it is presently produced in Saskatchewan, is used primarily as fertilizer, a source of potassium, one of three essential elements required for healthy plant growth, with about 5% of production sold to the chemical industry for use in such products as soap and liquid detergent, glass and ceramics, textiles and some pharmaceuticals. Saskatchewan is estimated to have approximately 40% of known world potash reserves and its ten active mines account for some 25% of annual world production. POTASH CORPORATION OF SASKATCHEWAN In an effort to guarantee a fair and lasting economic benefit to the Province of Saskatchewan, the Potash Corporation of Saskatchewan (PCS) was created on February 4, 1975 through an Order-in-Council under the Crown Corporation&apos;s Act and later on April 1, 1976, the Potash Corporation Act provided for its continuation. PCS was given the mandate to acquire ownership of a significant portion of the potash mining capacity in Saskatchewan and to establish an organization capable of operating the facilities, marketing the product, and conducting all of the other activities necessary for a successful corporation competing in the world potash industry. The corporation is the largest potash producing and selling organization in the Western World - or third largest in the world. (See also Figure 1). PCS through its wholly-owned subsidiary, PCS Mining, has acquired a whole or partial interest in five geographically distinct producing properties or divisions, representing today more than 40% of Saskatchewan&apos;s potash producing capacity. The acquisition of each division was followed by a program designed to exploit and maximize the particular opportunities at each minesite for increased production. To that end, PCS Mining has taken an active lead in expanding to meet future demand and has implemented expansion programs at all properties except for its Esterhazy Division where it has a long-term processing agreement with International Minerals & Chemical Corporation (Canada) Limited. Through its wholly-owned subsidiaries, PCS Mining, PCS Sales and PCS Transport, this provincial crown corporation has the ability to operate as a producer and marketer of Saskatchewan&apos;s potash. In certain instances PCS, the parent company, assists in the financing of various projects undertaken by the subsidiaries and in other cases the subsidiary involved arranges its own financing. POTASH RESERVES As a background to the specific issue of financing, it is helpful to describe briefly the nature of the deposit which supports the industry - our collateral, if you like. The potash beds underlying Saskatchewan are sedimentary rock deposits formed by the gradual evaporation of an inland sea during the Middle Devonian period roughly 400 million years ago. Now known as the Prairie Evaporite, this formation stretches from North Dakota and Northeast Montana through Southern Saskatchewan into North-Central Alberta. These beds lie at mining depths ranging from 950 - 1000m (3,000 ft) below the surface, where conventional mining methods can be used, and to 1,650m (5,000 ft), where solution mining must be

Jan 1, 1985